CS22 www.vishay.com Vishay Sfernice Single Value Wirebondable Thin Film Chip Resistors FEATURES • Small size 20 mil x 20 mil • Very high ohmic value up to 10 M • Aluminum or gold terminations Actual Size Chromium silicon thin film is very well suited to produce high density and high ohmic value resistor chips. These high ohmic value chip resistors are available with improved performances and size when compared to thick film counterparts. • Good stability 0.1 % (2000 h, rated power at + 70 °C) • Wirebondable • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 SCHEMATIC AND PATTERN R STANDARD ELECTRICAL SPECIFICATIONS MODEL SIZE RESISTANCE RANGE RATED POWER P70 °C W LIMITING ELEMENT VOLTAGE V TOLERANCE ±% TEMPERATURE COEFFICIENT ± ppm/°C CS22 0202 10K to 10M 0.05 100 (1) 0.5, 1, 2 50, 100 Note (1) Higher on Al O 2 3 CLIMATIC SPECIFICATIONS MECHANICAL SPECIFICATIONS Operating temperature range - 55 °C to + 155 °C Resistive element Storage temperature range - 55 °C to + 155 °C Chromium silicon Passivation Silicon nitride Substrate material Silicon (consult Vishay for Al2O3) Bonding pads Aluminum or gold DIMENSIONS in millimeters (inches) 0.58 ± 0.05 (23 ± 2) 0.43 (17.2) 0.58 ± 0.05 0.43 (23 ± 2) (17.2) 0.58 ± 0.05 (23 ± 2) 0.47 (18.8) 0.58 ± 0.05 0.47 (23 ± 2) (18.8) Type A (Current) Type B (New) 0.125 min. (5 min.) 0.08 min. (3.2 min.) 0.08 min. (3.2 min.) 0.10 min. (4 min.) Note • Customer can get one or the other part, but positions of pads are similar. Revision: 21-Nov-13 Document Number: 60063 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CS22 www.vishay.com Vishay Sfernice DIMENSIONS in millimeters (inches) 0.4 max. (15.75 max.) TECHNICAL SPECIFICATIONS TEST Stability SPECIFICATIONS CONDITIONS ± 0.1 % typical, ± 0.2 maximum 2000 h at + 70 °C at Pn < - 20 dB typical MIL-STD-202 method 308 Noise Thermal EMF < 0.01 μV/°C Shelf life stability 200 ppm 1 year at + 25 °C Rated Power in % DERATING 100 80 60 40 20 0 0 25 50 75 100 125 150 175 Ambient Temperature in °C GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CS22-100KD0016 (preferred part number format) C S 2 GLOBAL MODEL 2 - 1 0 0 K D 0 0 1 VALUE TOLERANCE TERMINATIONS OPTION Decimal R, K or M D = ± 0.5 % F = ± 1.0 % G = ± 2.0 % Blank = Aluminum G = Gold Leave blank if no option 6 Historical Part Number example: CS22 150K 0.5 % R0016 (will continue to be accepted) CS22 150K 0.5 % R0016 HISTORICAL MODEL VALUE TOLERANCE OPTION Revision: 21-Nov-13 Document Number: 60063 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000