Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Q6008LTH1LED Series RoHS Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC in a single package, which saves user expense by eliminating the need for separate Triac and DIAC components. Q6008LTH1LED series is designed to meet low load current characteristics typical in LED lighting applications. By keeping holding current at 6mA maximum, this Quadrac series is characterized and specified to perform best with LED loads. The Q6008LTH1LED series is best suited for LED dimming controls to obtain the lowest levels of light output with a minimum probability of flickering. Q6008LTH1LED series is offered in the industry standard TO-220AB package with an isolated mounting tab that makes it best suited for adding an external heat sink. Agency Approval Agency Agency File Number L Package : E71639 ® Main Features Features Symbol Value Unit 8 A VDRM / VRRM 600 V DIAC VBO 33 to 43 V IT(RMS) Schematic Symbol Benefits • As low as 6mA max holding current • Provides full control of light out put at the extreme low end of load conditions. • UL recognized TO-220AB package • 2500V AC min isolation between mounting tab and active terminals • 110 °C rated junction • Improves margin of safe operation with less heat sinking required temperature MT2 MT1 T • di/dt performance of 70A/μs • Enable survivability of typically LED load operating characteristics • QUADRAC version includes intergrated DIAC • Simplicity of circuit design & layout Applications Excellent for AC switching and phase control applications such as lighting and motor speed controls. Typical applications are AC solid-state switches, light dimmers with LED loads, small low current motor in power tools, and low current motors in home/brown goods appliances. Internally constructed isolated package is offered for ease of heat sinking with highest isolation voltage. Q6008LTH1LED Series 1 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Absolute Maximum Ratings Symbol Parameter Value Unit Tc = 80°C 8 A single half cycle; f = 50Hz; TJ (initial) = 25°C 80 single half cycle; f = 60Hz; TJ (initial) = 25°C 85 30 A 2s RMS forward current IT(RMS) ITSM Peak non-repetitive surge current I2t I2t value for fusing tp = 8.3ms Critical rate-of-rise of on-state current f = 60Hz; TJ =110°C 70 A/µs Peak gate current TJ = 110°C 1.5 A Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 110 °C Value Unit di/dt IGM Tstg TJ A Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Alternistor Quadrac Symbol Test Conditions IH IT = 15mA (initial) MAX. 6 mA dv/dt VD = VDRM; gate open; TJ=110°C MIN. 50 V/μs dv/dt(c) di/dt(c) = 0.54 x IT(rms) / ms; TJ = 110°C MIN. 10 V/μs tgt (note 1) TYP. 3 μs Value Unit MAX. 3 V MIN. 33 MAX. 43 (1) Reference test circuit in figure 7 and waveform in figure 8; CT = 0.1μF with 0.1μs rise time. Trigger DIAC Specifications Symbol Test Conditions Breakover Voltage Symmetry ΔVBO VBO Breakover Voltage, forward and reverse [ΔV±] V Dynamic Breakback Voltage, forward and reverse (note 1) MIN. 5 V IBO Peak Breakover Current MAX. 25 uA CT Trigger Firing Capacitance MAX. 0.1 µF Value Unit 1.6 V (1) Reference test circuit in figure 7 and waveform in figure 8. Static Characteristics Symbol Test Conditions IT = 1.41 x IT(rms) A; tp = 380μs VTM IDRM / IRRM MAX. TJ = 25°C VDRM / VRRM TJ = 110°C MAX. 10 µA 500 Thermal Resistances Symbol Parameter Value Unit Rθ(J-C) Junction to case (AC) 2.8 °C/W Rθ(J-A) Junction to ambient 50 °C/W Q6008LTH1LED Series 2 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Figure 1: Normalized DC Holding Current vs. Junction Temperature Figure 2: On-State Current vs. On-State Voltage (Typical) Instantaneous On-state Current (iT) – Amps Ratio of IH/IH(TJ = 25°C) 2.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 45 40 TJ = 25°C 35 30 25 20 15 10 5 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Instantaneous On-state Voltage (vT) – Volts 110 Junction Temperature (TJ) -- °C Figure 4: Maximum Allowable Case Temperature vs. RMS On-State Current Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation [PD(AV)] - (Watts) Figure 3: Power Dissipation vs. RMS On-State Current (Typical) 120 12 10 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 8 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 110 100 6 4 2 0 0 2 4 6 8 10 RMS On-State Current [IT(RMS)] - (Amps) 90 80 70 0 2 4 6 8 10 12 RMS On-State Current [IT(RMS)] - Amps Figure 5: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 1 10 100 1000 Surge Current Duration -- Full Cycles Q6008LTH1LED Series 3 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Figure 7: Test Circuit Figure 6: DIAC VBO Change vs. Junction Temperature 6% RL VBO Change -- % 4% 2% D.U.T. 120 V 60 Hz 0% MT2 -2% -4% T -6% VC -8% -40 -20 0 20 40 60 80 100 120 CT = 0.1 µF 140 MT1 Junction Temperature (TJ) -- °C Figure 8: Test Circuit Waveform VC +VBO ∆V+ ∆V-VBO Q6008LTH1LED Series 4 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds 260°C +0/-5 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 1005 Matte Tin-plated Body Material UL Recognized epoxy meeting flammability classification 94v-0 Lead Material Copper Alloy tL TS(max) Preheat TS(min) Ramp-do Ramp-down tS time to peak temperature Time Environmental Specifications Test Specifications and Conditions MIL-STD-750: Method 1040, Condition A High Temperature Rated VDRM (VAC-peak), 110°C, 1008 Voltage Blocking hours MIL-STD-750: Method 1051 Temperature Cycling -40°C to 150°C, 15-minute dwell, 100 cycles Biased Temperature & EIA/JEDEC: JESD22-A101 Humidity 320VDC, 85°C, 85%RH, 1008 hours MIL-STD-750: Method 1031 High Temp Storage 150°C, 1008 hours Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Q6008LTH1LED Series Ramp-up TL 25 Peak Temperature (TP) tP TP Temperature Reflow Condition Low-Temp Storage -40°C, 1008 hours Thermal Shock MIL-STD-750: Method 1056 0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles Autoclave EIA/JEDEC: JESD22-A102 (Pressure Cooker Test) 121°C, 100%RH, 2atm, 168 hours Resistance to Solder Heat MIL-STD-750: Method 2031 260°C, 10 seconds Solderability ANSI/J-STD-002, Category 3, Test A Lead Bend MIL-STD-750: Method 2036, Condition E 5 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor Quadrac for LED dimmer applications Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E Dimension 8.13 .320 P B C AREA (REF.) 0.17 in 2 13.36 .526 D 7.01 .276 F R G L H K N J M MT1 MT2 T (Trigger) Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Product Selector Part Number Type Package Q6008LTH1LED Alternistor Quadrac TO-220L Packing Options Part Number Marking Weight Packing Mode Q6008LTH1LED Q6008LTH1 2.2 g Bulk 500 Q6008LTH1LEDTP Q6008LTH1 2.2 g Tube 500 (50 per tube) Part Numbering System Base Quantity Part Marking System TO-220 AB - (L Package) Q 60 08 L T H1 LED DEVICE TYPE Q: Quadrac LED LIGHTING APPLICATION VOLTAGE RATING 60: 600V TRIAC TYPE H1: Low Holding Current Alternistor Quadrac CURRENT RATING 08: 8A Trigger T: Internal Diac (33V – 43V) Q6008LTH1 YMXXX ® PACKAGE TYPE L: TO-220 (Isolated) Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Q6008LTH1LED Series 6 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.