LCD-008N002A1-NFG-ET www.vishay.com Vishay 8 x 2 Character LCD FEATURES • Type: Character • Display format: 8 x 2 characters • Built-in controller: ST 7066 or equivalent • Duty cycle: 1/16 • 5 x 8 dots includes cursor • + 5 V power supply • LED can be driven by pin 1, pin 2, or A and K • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA ITEM ABSOLUTE MAXIMUM RATINGS STANDARD VALUE Module Dimension UNIT 58.0 x 32.0 x 8.9 max. ITEM SYMBOL STANDARD VALUE MIN. TYP. MAX. Viewing Area 38.0 x 16.0 Power Supply VDD to VSS - 0.3 - 7.0 Dot Size 0.56 x 0.66 Input Voltage VI VSS - VDD Dot Pitch 0.60 x 0.70 Mounting Hole 53.0 x 27.0 Character Size 2.96 x 5.56 mm UNIT V Note • VSS = 0 V, VDD = 5.0 V ELECTRICAL CHARACTERISTICS ITEM SYMBOL CONDITION Input Voltage VDD Supply Current IDD Recommended LC Driving Voltage for Normal Temperature Version Module VDD to V0 STANDARD VALUE UNIT MIN. TYP. MAX. VDD = + 5 V 4.7 5.0 5.3 V VDD = + 5 V 1.0 1.2 1.5 mA 5.5 - 20 °C - - 0 °C - - - 25 °C - 4.4 - 50 °C - - - 70 °C 3.5 - - V LED Forward Voltage VF 25 °C - 4.2 4.6 V LED Forward Current IF 25 °C - 70 140 mA EL Power Supply Current IEL VEL = 110 VAC, 400 Hz - - 5.0 mA OPTIONS PROCESS COLOR BACKLIGHT TN STN GRAY STN YELLOW STN BLUE FSTN B&W STN COLOR NONE LED EL CCFL x x x x x - x x x - For detailed information, please see the “Product Numbering System” document. DISPLAY CHARACTER ADDRESS CODE Display Position 1 2 3 4 5 6 7 8 DD RAM Address 00 01 02 03 04 05 06 07 DD RAM Address 40 41 42 43 44 45 46 47 Revision: 08-Jan-13 Document Number: 37470 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay INTERFACE PIN FUNCTIONS PIN NO. SYMBOL FUNCTION 1 VSS Ground 2 VDD Supply voltage for logic + 5 V 3 V0 Operating voltage for LCD (variable) 4 RS H: Data, L: Instruction code 5 RW H: Read (MPU module), L: Write (MPU module) 6 E Chip enable signal 7 DB0 Data bus line 8 DB1 Data bus line 9 DB2 Data bus line 10 DB3 Data bus line 11 DB4 Data bus line 12 DB5 Data bus line 13 DB6 Data bus line 14 DB7 Data bus line 15 n/a no connection 16 n/a no connection 58.0 ± 0.5 43.2 38.0(VA) 27.81(AA) A 27.0 K 29.0 4- 2.5 PTH 4- 5.0 PAD 53.0 1.6 EL or NO B/L 2.54 2.96 1.7 0.59 0.60 0.56 15 17.78 (P2.54*7) 16 2 5.56 0.70 0.66 The non-specified tolerance of dimension is ± 0.3 mm. 16- 1.0 PTH 16- 1.8 PAD 1 PIN DETAIL Revision: 08-Jan-13 0.38 7.11 2.5 8.9 max. 4.5 2.5 7.4 10.0 15.095 32.0 ± 0.5 26.2 16.0(VA) 11.5(AA) 2.9 8.0 10.25 DIMENSIONS in millimeters DOT SIZE SCALE 5/1 Document Number: 37470 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 1.Module Classification Information ʳ ʳ ʳ ʳ LCDc 008 d N 002 e f A1 g -N h F G -ET i j k 1. BrandΚVishay Intertechnology, Inc. 2. Horizontal Format: 8 characters 3. Display TypeΚNШCharacter Type, HШGraphic Type 4. Vertical Format: 2 lines 5. Model serials no.: A1 6. Backlight NШWithout backlight TШLED, White TypeΚ BШEL, Blue green AШLED, Amber DШEL, Green RШLED, Red WШEL, White OШLED, Orange FШCCFL, White GШLED, Green YШLED, Yellow Green 7. LCD ModeΚ BШTN Positive, Gray TШFSTN Negative NШTN Negative, GШSTN Positive, Gray YШSTN Positive, Yellow Green MШSTN Negative, Blue FШFSTN Positive 8. LCD Polarizer AШReflective, N.T, 6:00 HШTransflective, W.T,6:00 Type/ Temperature DШReflective, N.T, 12:00 KШTransflective, W.T,12:00 range/ View GШReflective, W. T, 6:00 CШTransmissive, N.T,6:00 direction JШReflective, W. T, 12:00 FШTransmissive, N.T,12:00 BШTransflective, N.T,6:00 IШTransmissive, W. T, 6:00 EШTransflective, N.T.12:00 LШTransmissive, W.T,12:00 9. Special Code ET : English and European standard font; Compliance with the ROHS Directions and regulations Revision: 08-Jan-13 Document Number: 37470 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 2.Precautions in use of LCD Modules (1)Avoid applying excessive shocks to the module or making any alterations or modifications to it. (2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of LCD module. (3)Don’t disassemble the LCM. (4)Don’t operate it above the absolute maximum rating. (5)Don’t drop, bend or twist LCM. (6)Soldering: only to the I/O terminals. (7)Storage: please storage in anti-static electricity container and clean environment. (8)Supplier has the right to change the passive components (Resistors, capacitors and other passive components will have different appearance and color caused by the different supplier.) (9)Supplier has the right to change the PCB Rev. 3.General Specification Item Dimension 8 characters x 2 Lines Unit Ё 58.0 x 32.0 x 8.9 (MAX) mm View area 38.0 x 16.0 mm Active area 27.81 x 11.5 mm Dot size 0.56 x 0.66 mm Dot pitch 0.60 x 0.70 mm Character size 2.96 x 5.56 mm Character pitch 3.55 x 5.94 mm Number of Characters Module dimension LCD type FSTN Positive Reflective, (In LCD production, It will occur slightly color difference. We can only guarantee the same color in the same batch.) Duty 1/16 View direction 6 o’clock Backlight Type Without backlight Revision: 08-Jan-13 Document Number: 37470 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 4.Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature T OP -20 Ё +70 к Storage Temperature T ST -30 Ё +80 к Input Voltage VI V SS Ё V DD V Supply Voltage For Logic VDD-V SS -0.3 Ё 7 V Supply Voltage For LCD V DD -V 0 -0.3 Ё 13 V 5.Electrical Characteristics Item Supply Voltage For Logic Supply Voltage For LCD *Note Symbol Condition Min Typ Max Unit V DD -V SS Ё 4.5 5.0 5.5 V Ta=-20к Ё Ё 5.5 V Ta=25к Ё 4.4 Ё V Ta=70к 3.5 Ё Ё V V DD -V 0 Input High Volt. V IH Ё 0.7 V DD Ё V DD V Input Low Volt. V IL Ё V SS Ё 0.6 V Output High Volt. V OH Ё 3.9 Ё V DD V Output Low Volt. V OL Ё Ё Ё 0.4 V Supply Current I DD V DD =5V 1.0 1.2 1.5 mA * Note: Please design the VOP adjustment circuit on customer's main board Vdd VR 10K~20K Vo LCM Module VSS Revision: 08-Jan-13 Document Number: 37470 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 6.Optical Characteristics Item Symbol Condition Min Typ Max Unit (V)Ӱ CRЊ2 30 Ё 60 deg (H)ӽ CRЊ2 -45 Ё 45 deg CR Ё Ё 5 Ё Ё T rise Ё Ё 150 200 ms T fall Ё Ё 150 200 ms View Angle Contrast Ratio Response Time @ 25C Definition of Operation Voltage (Vop) Intensity 100䋦 Definition of Response Time ( Tr , Tf ) Non-selected Conition Selected Wave Non-selected Wave Selected Conition Non-selected Conition Intensity 10䋦 Cr Max Cr = Lon / Loff 90䋦 100䋦 Vop Tr Driving Voltage(V) [positive type] Tf [positive type] Conditions : Operating Voltage : Vop Viewing Angle(ӰΔӽ) : 0̓Δ 0̓ Frame Frequency : 64 HZ Driving Waveform : 1/N duty , 1/a bias Definition of viewing angle(CRЊ2) f l b = 180° r = 90° = 270° = 0° Revision: 08-Jan-13 Document Number: 37470 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 7.Interface Pin Function Pin No. Symbol Level Description 1 V SS 0V 2 V DD 5.0V 3 VO 4 RS H/L H: DATA, L: Instruction code 5 R/W H/L H: Read(MPUШModule) L: Write(MPUШModule) 6 E H,HШL 7 DB0 H/L Data bus line 8 DB1 H/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line 15 N/A N/C 16 N/A N/C Revision: 08-Jan-13 Ground Supply Voltage for logic (Variable) Operating voltage for LCD Chip enable signal Document Number: 37470 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay A 27.0 K 29.0 7.11 2.5 8.9 max 4.5 2.5 7.4 10.0 15.095 58.0 0.5 43.2 38.0(VA) 27.81(AA) 32.0 0.5 26.2 16.0(VA) 11.5(AA) 2.9 8.0 10.25 8.Contour Drawing &Block Diagram 4- 2.5 PTH 4- 5.0 PAD 53.0 EL or NO B/L 2.54 1.7 15 17.78 (P2.54*7) 16 1.6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Vss Vdd Vo RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 N/A N/A 16- 1.0 PTH 16- 1.8 PAD 2 2.96 1 0.59 0.60 0.56 PIN DETAIL 0.38 5.56 0.70 0.66 The non-specified tolerance of dimension is ¡ 0À.3 mm . Revision: 08-Jan-13 DOT SIZE SCALE 5/1 Document Number: 37470 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com 80 series or 68 series VR 10K~20K Vdd Vo Vss Com1~8 Controller/Com Driver ST7066U or Equivalent Bias and Power Circuit MPU RS R/W E DB0~DB7 Vishay Com9~16 8X2 LCD Seg1~40 External contrast adjustment. Character located DDRAM address DDRAM address Revision: 08-Jan-13 1 2 3 4 5 6 7 8 00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47 Document Number: 37470 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 9.Function Description The LCD display Module is built in a LSI controller, the controller has two 8-bit registers, an instruction register (IR) and a data register (DR). The IR stores instruction codes, such as display clear and cursor shift, and address information for display data RAM (DDRAM) and character generator (CGRAM). The IR can only be written from the MPU. The DR temporarily stores data to be written or read from DDRAM or CGRAM. When address information is written into the IR, then data is stored into the DR from DDRAM or CGRAM. By the register selector (RS) signal, these two registers can be selected. RS R/W Operation 0 0 IR write as an internal operation (display clear, etc.) 0 1 Read busy flag (DB7) and address counter (DB0 to DB7) 1 0 Write data to DDRAM or CGRAM (DR to DDRAM or CGRAM) 1 1 Read data from DDRAM or CGRAM (DDRAM or CGRAM to DR) Busy Flag (BF) When the busy flag is 1, the controller LSI is in the internal operation mode, and the next instruction will not be accepted. When RS=0 and R/W=1, the busy flag is output to DB7. The next instruction must be written after ensuring that the busy flag is 0. Address Counter (AC) The address counter (AC) assigns addresses to both DDRAM and CGRAM Display Data RAM (DDRAM) This DDRAM is used to store the display data represented in 8-bit character codes. Its extended capacity is 80ͪ8 bits or 80 characters. Below figure is the relationship between DDRAM addresses and positions on the liquid crystal display. High bits Low bits Example: DDRAM addresses 4E AC (hexadecimal) Revision: 08-Jan-13 AC6 AC5 AC4 AC3 AC2 AC1 AC0 1 0 0 1 1 1 0 Document Number: 37470 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay Display position DDRAM address 1 00 40 2 3 4 5 6 7 8 01 02 41 42 03 43 04 05 06 07 44 45 46 47 2-Line by 8-Character Display Character Generator ROM (CGROM) The CGROM generate 5ͪ8 dot or 5ͪ10 dot character patterns from 8-bit character codes. See Table 2. Character Generator RAM (CGRAM) In CGRAM, the user can rewrite character by program. For 5ͪ8 dots, eight character patterns can be written, and for 5ͪ10 dots, four character patterns can be written. Write into DDRAM the character code at the addresses shown as the left column of table 1. To show the character patterns stored in CGRAM. Revision: 08-Jan-13 Document Number: 37470 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay Relationship between CGRAM Addresses, Character Codes (DDRAM) and Character patterns Table 1. For 5 * 8 dot character patterns Character Codes ( DDRAM data ) 7 6 5 4 3 2 1 0 High 0 0 0 0 0 0 0 0 0 0 0 0 Low * 0 0 0 * 0 0 1 * 1 1 1 CGRAM Address 5 4 3 2 1 0 Low 0 0 0 0 0 1 0 1 0 0 0 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 0 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 0 1 0 1 Character Patterns ( CGRAM data ) 7 6 5 4 3 2 1 0 High 0 0 1 1 * * * * * * * * * * * * * * * * * High * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Low 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Character pattern( 1 ) 0 0 Character pattern( 2 ) 0 0 0 0 0 0 0 0 0 0 0 0 0 Cursor pattern Cursor pattern * * * For 5 * 10 dot character patterns Character Codes ( DDRAM data ) 7 6 5 4 3 2 1 0 High 0 0 0 0 Low * 0 0 0 CGRAM Address 5 4 3 2 1 0 High Character Patterns ( CGRAM data ) 7 6 5 4 3 2 1 0 Low 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 High 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 * * * * * * * * * * * * * * * * * * * * * * Low * 0 0 0 0 0 * 0 0 0 0 0 0 0 * 0 0 * 0 0 0 * 0 0 0 * 0 * 0 0 0 0 * 0 0 0 0 * 0 0 0 0 * * 0 0 0 0 0 Character pattern Cursor pattern * * * * * * * * : " High " Revision: 08-Jan-13 Document Number: 37470 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 10.Character Generator ROM Pattern Table.2 Upper 4 bit Lower 4 bit LLLL LLLH LLHL LLHH LHLL LHLH LHHL LHHH HLLL HLLH HLHL HLHH HHLL HHLH HHHL HHHH LLLL CG RAM (1) LLLH CG RAM (2) LLHL CG RAM (3) LLHH CG RAM (4) LHLL CG RAM (5) LHLH CG RAM (6) LHHL CG RAM (7) LHHH CG RAM (8) HLLL CG RAM (1) HLLH CG RAM (2) HLHL CG RAM (3) HLHH CG RAM (4) HHLL CG RAM (5) HHLH CG RAM (6) HHHL CG RAM (7) HHHH CG RAM (8) Revision: 08-Jan-13 Document Number: 37470 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 11.Instruction Table Instruction Code Instruction Execution time (fuss=270Khz) Description RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Clear Display 0 0 0 0 0 0 0 0 0 1 Write “00H” to DDRAM and set DDRAM address to “00H” from AC 1.53ms Set DDRAM address to “00H” from AC and return cursor to its original position if shifted. The contents of DDRAM are not changed. 1.53ms Assign cursor moving direction and enable the shift of entire display. 39Ӵs Set display (D), cursor (C), and blinking of cursor (B) on/off control bit. 39Ӵs Return Home 0 0 0 0 0 0 0 0 1 Ё Entry Mode Set 0 0 0 0 0 0 0 1 I/D SH Display ON/OFF Control 0 0 0 0 0 0 1 D C B Cursor or Display Shift 0 0 0 0 0 1 Ё Ё control bit, and the direction, without Function Set Set CGRAM Address Set DDRAM Address Set cursor moving and display shift S/C R/L 39Ӵs changing of DDRAM data. Set interface data length (DL:8-bit/4-bit), numbers of display line (N:2-line/1-line)and, display font type (F:5ͪ11 dots/5ͪ8 dots) 39Ӵs AC5 AC4 AC3 AC2 AC1 AC0 Set CGRAM address in address counter. 39Ӵs 1 DL N F Ё Ё 0 0 0 0 0 0 0 1 0 0 1 AC6 AC5 AC4 AC3 AC2 AC1 AC0 Set DDRAM address in address counter. 39Ӵs Whether during internal operation or not can be known by reading BF. The AC6 AC5 AC4 AC3 AC2 AC1 AC0 contents of address counter can also be read. 0Ӵs Read Busy Flag and Address 0 1 BF Write Data to RAM 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Write data into internal RAM (DDRAM/CGRAM). 43Ӵs Read Data from RAM 1 1 D7 D6 D5 D4 D3 D2 D1 D0 Read data from internal RAM (DDRAM/CGRAM). 43Ӵs Ϡ ”Ё”Κdon’t care Revision: 08-Jan-13 Document Number: 37470 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 12.Timing Characteristics 12.1ʳʳ Writing data from MPU to ST7066U Ta=-30~+85к, VDD=5.0± 0.5V TC Enable Cycle Time Pin E 1200 - - ns TPW Enable Pulse Width Pin E 140 - - ns TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 0 - - ns TAH Address Hold Time Pins: RS,RW,E 10 - - ns TDSW Data Setup Time Pins: DB0 - DB7 40 - - ns TH Data Hold Time Pins: DB0 - DB7 10 - - ns Revision: 08-Jan-13 Document Number: 37470 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 12.2Reading data from ST7066U to MPU Ta=-30~+85к, VDD=5.0± 0.5V Read Mode (Reading Data from ST7066U to MPU) TC Enable Cycle Time Pin E 1200 - - ns TPW Enable Pulse Width Pin E 140 - - ns TR,TF Enable Rise/Fall Time Pin E - - 25 ns TAS Address Setup Time Pins: RS,RW,E 0 - - ns TAH Address Hold Time Pins: RS,RW,E 10 - - ns TDDR Data Setup Time Pins: DB0 - DB7 - - 100 ns TH Data Hold Time Pins: DB0 - DB7 10 - - ns Revision: 08-Jan-13 Document Number: 37470 16 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 13.Initializing of LCM Revision: 08-Jan-13 Document Number: 37470 17 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Revision: 08-Jan-13 Vishay Document Number: 37470 18 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 14.Reliability Content of Reliability Test (wide temperature, -20к~70к) Environmental Test Test Item High Temperature storage Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Operation Thermal shock resistance Content of Test Endurance test applying the high storage temperature for a long time. Endurance test applying the high storage temperature for a long time. Endurance test applying the electric stress (Voltage & Current) and the thermal stress to the element for a long time. Endurance test applying the electric stress under low temperature for a long time. The module should be allowed to stand at 60 к,90%RH max For 96hrs under no-load condition excluding the polarizer, Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of operation -20к 25к 70к 30min 1 cycle 5min Test Condition 80к 200hrs -30к 200hrs Note 2 1,2 70к 200hrs —— -20к 200hrs 1 60к,90%RH 96hrs -20к/70к 10 cycles 1,2 —— 30min Total fixed amplitude : 1.5mm Vibration Frequency : 10~55Hz Endurance test applying the vibration during 3 Vibration test One cycle 60 transportation and using. seconds to 3 directions of X,Y,Z for Each 15 minutes VS=800V,RS=1.5k Endurance test applying the electric stress to the Ө Static electricity test —— terminal. CS=100pF 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container. Revision: 08-Jan-13 Document Number: 37470 19 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 15. Inspection specification NO 01 02 Item Criterion AQL Electrical Testing 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character , dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 LCD viewing angle defect. 1.7 Mixed product types. 1.8 Contrast defect. 0.65 Black or white 2.1 White and black spots on display Љ0.25mm, no more than spots on LCD three white or black spots present. (display only) 2.2 Densely spaced: No more than two spots or lines within 3mm 3.1 Round type : As following drawing ӥːʻʳ̋ʳʾʳ̌ʳʼʳ˂ʳ˅ʳ ʳ ʳ ʳ ˦˜˭˘ʳ 2.5 ˔˶˶˸̃̇˴˵˿˸ʳˤʳ˧ˬʳ ʳ ʳ ʳ ʳ ʳ ӥЉ˃ˁ˄˃ʳ ˔˶˶˸̃̇ʳ́̂ʳ˷˸́̆˸ʳ ˃ˁ˄˃ІӥЉ˃ˁ˅˃ʳ 03 ˅ʳ ˃ˁ˅˃ІӥЉ˃ˁ˅ˈʳ ˄ʳ LCD black ʳ ˃ˁ˅ˈІӥʳ ˃ʳ spots, white spots, contamination (non-display) 3.2 Line type : (As following drawing) Length Width Acceptable Q TY --WЉ˃ˁ˃˅ Accept no dense LЉˆˁ˃ 0.02ІWЉ˃ˁ˃ˆ 2 LЉ˅ˁˈ 0.03ІWЉ˃ˁ˃ˈʳ --- Revision: 08-Jan-13 0.05ІW 2.5 2.5 As round type Document Number: 37470 20 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com 04 Polarizer bubbles If bubbles are visible, judge using black spot specifications, not easy to find, must check in specify direction. Vishay Size ӥ ӥЉ˃ˁ˅˃ Acceptable Q TY Accept no dense ˃ˁ˅˃ІӥЉ˃ˁˈ˃ 3 ˃ˁˈ˃ІӥЉ˄ˁ˃˃ 2 ˄ˁ˃˃Іӥ 0 Total Q TY NO Item 05 Scratches Revision: 08-Jan-13 Criterion 2.5 3 AQL Follow NO.3 LCD black spots, white spots, contamination Document Number: 37470 21 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length: 6.1 General glass chip : 6.1.1 Chip on panel surface and crack between panels: Chipped glass 06 ̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ ̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ ˭Љ˄˂˅̇ʳ ˡ̂̇ʳ̂̉˸̅ʳ̉˼˸̊˼́˺ʳ˴̅˸˴ʳ ̋Љ˄˂ˋ˴ʳ ˄˂˅̇І̍Љ˅̇ʳ ˡ̂̇ʳ˸̋˶˸˸˷ʳ˄˂ˆ˾ʳ ʳ ̋Љ˄˂ˋ˴ʳ 2.5 Ф˜˹ʳ̇˻˸̅˸ʳ˴̅˸ʳ˅ʳ̂̅ʳ̀̂̅˸ʳ˶˻˼̃̆ʿʳ̋ʳ˼̆ʳ̇̂̇˴˿ʳ˿˸́˺̇˻ʳ̂˹ʳ˸˴˶˻ʳ˶˻˼̃ˁʳ ʳ ˉˁ˄ˁ˅ʳ˖̂̅́˸̅ʳ˶̅˴˶˾ˍʳ ʳ ̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ ʳ ̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ˭Љ˄˂˅̇ʳ ˡ̂̇ʳ̂̉˸̅ʳ̉˼˸̊˼́˺ʳ˴̅˸˴ʳ ̋Љ˄˂ˋ˴ʳ ˄˂˅̇І̍Љ˅̇ʳ ˡ̂̇ʳ˸̋˶˸˸˷ʳ˄˂ˆ˾ʳ ʳ ̋Љ˄˂ˋ˴ʳ ̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ Ф˜˹ʳ̇˻˸̅˸ʳ˴̅˸ʳ˅ʳ̂̅ʳ̀̂̅˸ʳ˶˻˼̃̆ʿʳ̋ʳ˼̆ʳ̇˻˸ʳ̇̂̇˴˿ʳ˿˸́˺̇˻ʳ̂˹ʳ˸˴˶˻ʳ˶˻˼̃ˁʳ ʳ NO Item Revision: 08-Jan-13 Criterion AQL Document Number: 37470 22 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay ˦̌̀˵̂˿̆ʳˍʳ x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : ̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ʳ ̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ ̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ ̌Љ˃ˁˈ̀̀ʳ ̋Љ˄˂ˋ˴ʳ ˃ʳ Іʳ ̍ʳЉʳ̇ʳ ˉˁ˅ˁ˅ʳˡ̂́ˀ˶̂́˷̈˶̇˼̉˸ʳ̃̂̅̇˼̂́ˍʳ 06 Glass crack 2.5 ̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ʳ ̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ ̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ ̌Љʳ˟ʳ ̋Љ˄˂ˋ˴ʳ ˃ʳ Іʳ ̍ʳЉʳ̇ʳ ʳ Ф˜˹ʳ̇˻˸ʳ˶˻˼̃̃˸˷ʳ˴̅˸˴ʳ̇̂̈˶˻˸̆ʳ̇˻˸ʳ˜˧ˢʳ̇˸̅̀˼́˴˿ʿʳ̂̉˸̅ʳ˅˂ˆʳ̂˹ʳ̇˻˸ʳ˜˧ˢʳ̀̈̆̇ʳ ̅˸̀˴˼́ʳ˴́˷ʳ˵˸ʳ˼́̆̃˸˶̇˸˷ʳ˴˶˶̂̅˷˼́˺ʳ̇̂ʳ˸˿˸˶̇̅̂˷˸ʳ̇˸̅̀˼́˴˿ʳ̆̃˸˶˼˹˼˶˴̇˼̂́̆ˁʳ Ф˜˹ʳ̇˻˸ʳ̃̅̂˷̈˶̇ʳ̊˼˿˿ʳ˵˸ʳ˻˸˴̇ʳ̆˸˴˿˸˷ʳ˵̌ʳ̇˻˸ʳ˶̈̆̇̂̀˸̅ʿʳ̇˻˸ʳ˴˿˼˺́̀˸́̇ʳ̀˴̅˾ʳ ́̂̇ʳ˵˸ʳ˷˴̀˴˺˸˷ˁʳ ˉˁ˅ˁˆʳ˦̈˵̆̇̅˴̇˸ʳ̃̅̂̇̈˵˸̅˴́˶˸ʳ˴́˷ʳ˼́̇˸̅́˴˿ʳ˶̅˴˶˾ˁʳ ʳ Revision: 08-Jan-13 ̌ˍʳ̊˼˷̇˻ʳ ʳ ̋ˍʳ˿˸́˺̇˻ʳ ̌Љ˄˂ˆ˟ʳ ̋ʳЉʳ˴ʳ ʳ Document Number: 37470 23 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com NO Item 07 Cracked glass 08 09 10 Backlight elements Bezel PCBΕCOB Vishay Criterion ˧˻˸ʳ˟˖˗ʳ̊˼̇˻ʳ˸̋̇˸́̆˼̉˸ʳ˶̅˴˶˾ʳ˼̆ʳ́̂̇ʳ˴˶˶˸̃̇˴˵˿˸ˁʳ ʳ ˋˁ˄ʳ˜˿˿̈̀˼́˴̇˼̂́ʳ̆̂̈̅˶˸ʳ˹˿˼˶˾˸̅̆ʳ̊˻˸́ʳ˿˼̇ˁʳ ˋˁ˅ʳ˦̃̂̇̆ʳ̂̅ʳ̆˶̅˴̇˶˻˸˷ʳ̇˻˴̇ʳ˴̃̃˸˴̅ʳ̊˻˸́ʳ˿˼̇ʳ̀̈̆̇ʳ˵˸ʳ˽̈˷˺˸˷ˁʳ˨̆˼́˺ʳ ˟˖˗ʳ̆̃̂̇ʿʳ˿˼́˸̆ʳ˴́˷ʳ˶̂́̇˴̀˼́˴̇˼̂́ʳ̆̇˴́˷˴̅˷̆ˁʳ ˋˁˆʳ˕˴˶˾˿˼˺˻̇ʳ˷̂˸̆́ϗ̇ʳ˿˼˺˻̇ʳ̂̅ʳ˶̂˿̂̅ʳ̊̅̂́˺ˁʳ ʳ ʳ ˌˁ˄ʳ˕˸̍˸˿ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̅̈̆̇ʿʳ˵˸ʳ˷˸˹̂̅̀˸˷ʳ̂̅ʳ˻˴̉˸ʳ˹˼́˺˸̅̃̅˼́̇̆ʿʳ̆̇˴˼́̆ʳ ̂̅ʳ̂̇˻˸̅ʳ˶̂́̇˴̀˼́˴̇˼̂́ˁʳ ˌˁ˅ʳ˕˸̍˸˿ʳ̀̈̆̇ʳ˶̂̀̃˿̌ʳ̊˼̇˻ʳ˽̂˵ʳ̆̃˸˶˼˹˼˶˴̇˼̂́̆ˁʳ ʳ ʳ ˄˃ˁ˄ʳ˖ˢ˕ʳ̆˸˴˿ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̃˼́˻̂˿˸̆ʳ˿˴̅˺˸̅ʳ̇˻˴́ʳ˃ˁ˅̀̀ʳ̂̅ʳ ˶̂́̇˴̀˼́˴̇˼̂́ˁʳ ˄˃ˁ˅ʳ˖ˢ˕ʳ̆˸˴˿ʳ̆̈̅˹˴˶˸ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̃˼́˻̂˿˸̆ʳ̇˻̅̂̈˺˻ʳ̇̂ʳ̇˻˸ʳ˜˖ˁʳ ˄˃ˁˆʳThe height of the COB should not exceed the height indicated in the assembly diagram. 10.4 There may not be more than 2mm of sealant outside the seal area on the PCB. And there should be no more than three places. 10.5 No oxidation or contamination PCB terminals. 10.6 Parts on PCB must be the same as on the production characteristic chart. There should be no wrong parts, missing parts or excess parts. 10.7 The jumper on the PCB should conform to the product characteristic chart. 10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw hold pad, make sure it is smoothed down. ˄˃ˁˌ The Scraping testing standard for Copper Coating of PCB AQL 2.5 0.65 2.5 0.65 2.5 0.65 2.5 2.5 0.65 2.5 2.5 0.65 0.65 2.5 2.5 X Y 11 Soldering Revision: 08-Jan-13 2 X * Y<=2mm ʳ ʳ ˄˄ˁ˄ʳˡ̂ʳ̈́ˀ̀˸˿̇˸˷ʳ̆̂˿˷˸̅ʳ̃˴̆̇˸ʳ̀˴̌ʳ˵˸ʳ̃̅˸̆˸́̇ʳ̂́ʳ̇˻˸ʳˣ˖˕ˁʳ ˄˄ˁ˅ʳˡ̂ʳ˶̂˿˷ʳ̆̂˿˷˸̅ʳ˽̂˼́̇̆ʿʳ̀˼̆̆˼́˺ʳ̆̂˿˷˸̅ʳ˶̂́́˸˶̇˼̂́̆ʿʳ̂̋˼˷˴̇˼̂́ʳ̂̅ʳ ˼˶˼˶˿˸ˁʳ ˄˄ˁˆʳˡ̂ʳ̅˸̆˼˷̈˸ʳ̂̅ʳ̆̂˿˷˸̅ʳ˵˴˿˿̆ʳ̂́ʳˣ˖˕ˁʳ ˄˄ˁˇʳˡ̂ʳ̆˻̂̅̇ʳ˶˼̅˶̈˼̇̆ʳ˼́ʳ˶̂̀̃̂́˸́̇̆ʳ̂́ʳˣ˖˕ˁʳ ʳ 2.5 2.5 2.5 0.65 Document Number: 37470 24 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com NO 12 Vishay Item Criterion General appearance 12.1 No oxidation, contamination, curves or, bends on interface Pin (OLB) of TCP. 12.2 No cracks on interface pin (OLB) of TCP. 12.3 No contamination, solder residue or solder balls on product. 12.4 The IC on the TCP may not be damaged, circuits. 12.5 The uppermost edge of the protective strip on the interface pin must be present or look as if it causes the interface pin to sever. 12.6 The residual rosin or tin oil of soldering (component or chip component) is not burned into brown or black color. 12.7 Sealant on top of the ITO circuit has not hardened. 12.8 Pin type must match type in specification sheet. 12.9 LCD pin loose or missing pins. 12.10 Product packaging must the same as specified on packaging specification sheet. 12.11 Product dimension and structure must conform to product specification sheet. Revision: 08-Jan-13 AQL 2.5 0.65 2.5 2.5 2.5 2.5 2.5 0.65 0.65 0.65 0.65 Document Number: 37470 25 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LCD-008N002A1-NFG-ET www.vishay.com Vishay 16. Material List of Components for RoHS 1. Declaration that all of or part of products (with the mark “N” in code), including, but not limited to, the LCM, accessories or packages, manufactured and/or delivered to your company (including your subsidiaries and affiliated company) directly or indirectly by our company (including our subsidiaries or affiliated companies) do not intentionally contain any of the substances listed in all applicable EU directives and regulations, including the following substances. Exhibit AΚThe Harmful Material List Material (Cd) (Pb) (Hg) (Cr6+) PBBs PBDEs Limited 100 1000 1000 1000 1000 1000 Value ppm ppm ppm ppm ppm ppm Above limited value is set up according to RoHS. 2.Process for RoHS requirementΚ (1) Use the Sn/Ag/Cu soldering surfaceΙthe surface of Pb-free solder is rougher than we used before. (2) Heat-resistance temp.Κ ReflowΚ250°C, 30 seconds Max.Ι Connector soldering wave or hand solderingΚ320°C, 10 seconds max. (3) Temp. curve of reflow, max. Temp.Κ235°C ±5 degreesΙ Recommended customer’s soldering temp. of connectorΚ280°C, 3 seconds. 17. Recommendable Storage 1. Place the panel or module in the temperature 25°C±5°C and the humidity below 65% RH 2. Do not place the module near organics solvents or corrosive gases. 3. Do not crush, shake, or jolt the module Revision: 08-Jan-13 Document Number: 37470 26 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000