MTR www.vishay.com Vishay Electro-Films Wire Bondable Thin Film Multi-Tap Resistor Arrays FEATURES • Wire bondable • Selectable values by wire bonding • Chip size: 0.030" x 0.030" • Case: 0303 • Standard resistance range: 100 to 24 k or 800 to 240 k • Resistor material: Tantalum nitride, self-passivating Product may not be to scale The MTR multi-tap resistors, available in two formats, offer eleven taps allowing the user to select specified increments a wide range of values. The desired resistance value is obtained by bonding the wires to the appropriate pads. These chips are manufactured using Vishay Electro-Films (EFI) sophisticated Thin Film equipment and manufacturing technology. The MTRs are 100 % electrically tested and visually inspected to MIL-STD-883. • Oxidized silicon substrate for good power dissipation • Ideally suited for hybrid prototyping • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS The MTR series of multi-tap resistor chips are designed to satisfy the requirements of prototype development and circuit trimming in hybrid packages through selective wire-bonding. TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER Total Resistance Range Format A Format B 7 Resistors Between Pads 1 and 8 5 Resistors Between Pads 8 and 13 Standard Tolerances TCR VALUE UNIT 100, 200, 400, 800, 2.4K, 8K, 24K 800, 2.4K, 8K, 24K, 80K, 160K, 240K Each 12.5 % of total resistance Each 2.5 % of total resistance ± 10, ± 20 of total resistance of all 12 resistors % ± 100 ppm/°C Example: When the total resistance value is 8 k, the resistors between pads 8 and 13 are 200 each, and the resistors between pads 1 and 8 are 1 k each. STANDARD ELECTRICAL SPECIFICATIONS PARAMETER TCR Tracking Between Elements Noise, MIL-STD-202, Method 308 VALUE UNIT ±5 ppm/°C - 30 typ. dB Moisture Resistance, MIL-STD-202, Method 106 ± 0.5 max. R/R % Stability, 1000 h, + 125 °C, 125 mW ± 0.5 max. R/R % - 55 to + 125 °C Thermal Shock, MIL-STD-202, Method 107, Test Condition F ± 0.25 max. R/R % High Temperature Exposure + 150 °C, 100 h ± 0.5 max. R/R % Operating Temperature Range Dielectric Voltage Breakdown Insulation Resistance Operating Voltage DC Power Rating at + 70 °C (Derated to Zero at + 175 °C) 5 x Rated Power Short-Time Overload, + 25 °C, 5 s Revision: 18-Apr-13 200 V 1012 min. 100 max. V 0.250, total R W ± 0.25 max. R/R % Document Number: 61045 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MTR www.vishay.com Vishay Electro-Films DIMENSIONS in inches 0.030 0.030 0.030 0.030 0.004 0.004 0.004 0.004 Format B Format A SCHEMATIC 13 R R 5R 5R R R 5R R 5R 5R 5R 1 R T = 40R MECHANICAL SPECIFICATIONS PARAMETER Chip Size 0.030" x 0.030" ± 0.003" (0.762 mm x 0.762 mm ± 0.076 mm) Chip Thickness 0.010" ± 0.002" (0.254 mm ± 0.05 mm) Chip Substrate Material Oxidized silicon, 10 kÅ minimum SiO2 Resistor Material Tantalum nitride, self-passivating Bonding Pads 0.004" x 0.004" (0.10 mm x 0.10 mm) Number of Top Pads 13 Pad Material 10 kÅ minimum aluminum Backing None, lapped semiconductor silicon GLOBAL PART NUMBER INFORMATION Global Part Number: MTR24001KAKANHWS Global Part Number Description: MTR 24K 10 %, format A, 100 ppm/°C, Al pads, no back metal, class H, WS M T R 2 4 0 MODEL RESISTANCE RESISTANCE MULTILPLIER CODE TOL. CODE (%) MTR First 4 digits are significant figures of resistance A = 0.1 0=1 1 = 10 2 = 100 J = 5.0 K = 10 M = 20 L = 25 0 1 FORMAT A = Form A B = Form B K TCR (ppm/°C) K = ± 100 M = ± 250 R = 0/- 250 A K A N H W S TERMINATION BACK METAL VISUAL CLASS PACKAGING CODE G = Gold A = Aluminum G = Gold N = None H = Class H K = Class K WS = Waffle pack 100 min, 1 mult Historical Part Number: WMTR05024001K (will continue to be accepted) Revision: 18-Apr-13 Document Number: 61045 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000