MTT Datasheet

MTT
www.vishay.com
Vishay Electro-Films
Wire Bondable Thin Film Multi-Tap Resistor Arrays
FEATURES
• Wire bondable
• Selectable values by wire bonding
• Resistance range: 1.1 k to 275 k
• Chip size: 0.038" x 0.038"
• Case: 0404
• Resistor
material
self-passivating
tantalum
nitride,
• Oxidized silicon substrate for good power dissipation
Product may not be to scale
The MTT multi-tap resistors offer nineteen taps allowing the
user to select specified increments and a wide range of
values. The desired resistance value is obtained by bonding
the wires to the appropriate pads.
These chips are manufactured using Vishay Electro-Films
(EFI) sophisticated Thin Film equipment and manufacturing
technology. The MTT’s are 100 % electrically tested and
visually inspected to MIL-STD-883.
• Ideally suited for hybrid prototyping
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
The MTT series of multi-tap resistor chips are designed to
satisfy the requirements of prototype development and
circuit trimming in hybrid packages through selective
wire-bonding.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
10 Resistors Between Pads 1 and 11
10 Resistors Between Pads 11 and 21
Standard Tolerances
VALUE
UNIT
1.1K, 2.75K, 5.5K, 11K, 27.5K, 55K, 110K, 275K

Each 9.1 % of total resistance
Each 0.91 % of total resistance
± 1, ± 5, ± 10, ± 20 of total resistance of all 20 resistors
%
± 250
ppm/°C
TCR
Example:
When the total resistance value is 55 k, the resistors between pads 11 and 21 are 500  each, and the resistors between
pads 1 and 11 are 5 k each.
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
VALUE
UNIT
TCR Tracking Between Elements
±5
ppm/°C
Noise, MIL-STD-202, Method 308
- 30 typ.
dB
Moisture Resistance, MIL-STD-202, Method 106
± 0.5 max. R/R
%
Stability, 1000 h, + 125 °C, 125 mW
± 0.5 max. R/R
%
- 55 to + 125
°C
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
± 0.25 max. R/R
%
High Temperature Exposure ± 150 °C, 100 h
± 0.5 max. R/R
%
Operating Temperature Range
Dielectric Voltage Breakdown
200
V
Insulation Resistance
1012 min.

Operating Voltage
100 max.
V
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Revision: 02-May-13
0.250, total R
W
± 0.25 max. R/R
%
Document Number: 61046
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MTT
www.vishay.com
Vishay Electro-Films
DIMENSIONS in inches
0.038
0.009
0.038
0.004
21
0.004
0.009
0.004
0.004
TYPICAL RANGE
1.1 kΩ to 5.5 kΩ
TYPICAL RANGE
11 kΩ to 275 kΩ
SCHEMATIC
R
R
R
21
R
R
R
R
R
R
R
10R
10R
10R
10R
10R
10R
10R
10R
10R
R T = 110 R
10R
1
MECHANICAL SPECIFICATIONS
PARAMETER
Chip Size
0.038" x 0.038" ± 0.002" (0.762 mm x 0.762 mm)
Chip Thickness
0.010" ± 0.002" (0.254 mm ± 0.05 mm)
Chip Substrate Material
Oxidized silicon, 10 kÅ minimum SiO2
Resistor Material
Tantalum nitride, self-passivating
Bonding Pads
0.004" x 0.004" (0.10 mm x 0.10 mm)
Number of Pads
21
Pad Material
10 kÅ minimum aluminum
Backing
None, lapped semiconductor silicon
GLOBAL PART NUMBER INFORMATION
Global Part Number: MTT11002KMANHWS
Global Part Number Description: MTT 110K 10 %, 250 ppm/°C, Al termination, no back metal, class H, WS
M
T
T
MODEL
RESISTANCE
MTT
First 4 digits
are significant
figures of
resistance
1
1
RESISTANCE
MULTIPLIER
CODE
A = 0.1
0=1
1 = 10
2 = 100
0
0
TOL.
CODE
(%)
F = 1.0
G = 2.0
J = 5.0
K = 10
M = 20
L = 25
2
K
TCR
(ppm/°C)
C = ± 50
K = ± 100
M = ± 250
R = 0/- 250
M
A
N
H
W
S
TERMINATION
BACK
METAL
VISUAL
CLASS
PACKAGING
CODE
G = Gold
A = Aluminum
G = Gold
N = None
H = Class H
K = Class K
WS =
Waffle pack
100 min,
1 mult
Historical Part Number: WMTT00210002K (will continue to be accepted)
Revision: 02-May-13
Document Number: 61046
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000