Si 4 7 0 7 - B20 W EATHER B A N D A N D SAME D A TA R ECEIVER Features Weather band support WB digital tuning Low-IF direct conversion with no (162.4–162.55 MHz) external ceramic filters SAME processor Excellent SAME sensitivity data quality metrics Advanced error correction 1050 Hz alert tone detection Excellent real-world performance Freq synthesizer with integrated VCO Automatic frequency control (AFC) Automatic gain control (AGC) Adaptive noise suppression Byte-wise 2.7 to 5.5 V supply voltage Ordering Information: See page 22. Firmware upgradeable 3 x 3 x 0.55 mm 20-pin QFN package Pin Assignments Pb-free/RoHS compliant Si4707-B20-GM Applications Emergency radios Table and portable radios Stereos Mini/micro systems Portable media players (Top View) Boom boxes Cellular handsets Modules Clock radios Mini HiFi NC 1 NP3 Integrated LDO regulator GPO3 (RSSI and SNR) 2-wire and 3-wire control interface GPO2/INT Receive signal quality indicators GPO1 Volume control NC Programmable reference clock 20 19 18 17 16 FMI 2 Description 15 NP2 RFGND 3 ADC FMI RFGND LNA PGA DAC LOUT DSP ADC DAC ROUT GPO GPO AGC 0/90 RSSI / SNR 6 7 8 9 10 RCLK VIO 12 GND SDIO RST 5 11 VDD CONTROL INTERFACE XTAL OSC SEN REG Patents pending Notes: 1. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic, Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers. 2. Place Si4707 as close as possible to antenna jack and keep the FMI traces as short as possible. VIO VDD SAME RST AFC SDIO RCLK SCLK 32.768 kHz Rev. 0.8 6/08 13 ROUT Si4707 Weather Band Antenna 2.7–5.5 V NP1 4 SCLK Functional Block Diagram 14 LOUT GND PAD SEN The Si4707 is the first digital CMOS weather band and SAME decoder receiver IC to integrate the complete tuner and decoder functionality from antenna input to audio and/or data output. Copyright © 2008 by Silicon Laboratories Si4707-B20 This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Si4707-B20 2 Rev. 0.8 Si4707-B20 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3. Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.2. Block Diagram Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.3. Weather Band Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.4. DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.5. SAME Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.6. Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.7. Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 4.8. Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 4.9. GPO Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.10. Firmware Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 4.11. Reset, Powerup, and Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.12. Programming with Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5. Commands and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6. Pin Descriptions: Si4707-B20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 8. Package Markings (Top Marks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.1. Top Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.2. Top Mark Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 9. Package Outline: Si4707 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 10. PCB Land Pattern: Si4707 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 11. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Rev. 0.8 3 Si4707-B20 1. Electrical Specifications Table 1. Recommended Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Supply Voltage VDD 2.7 — 5.5 V Interface Supply Voltage VIO 1.5 — 3.6 V Power Supply Powerup Rise Time VDDRISE 10 — — µs Interface Power Supply Powerup Rise Time VIORISE 10 — — µs TA –20 25 85 C Ambient Temperature Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at VDD = 3.3 V and 25 C unless otherwise stated. Parameters are tested in production unless otherwise stated. Table 2. Absolute Maximum Ratings1,2 Parameter Symbol Value Unit Supply Voltage VDD –0.5 to 5.8 V Interface Supply Voltage VIO –0.5 to 3.9 V 3 Input Current IIN 10 mA Input Voltage3 VIN –0.3 to (VIO + 0.3) V Operating Temperature TOP –40 to 95 C Storage Temperature TSTG –55 to 150 C 0.4 VpK RF Input Level 4 Notes: 1. Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond recommended operating conditions for extended periods may affect device reliability. 2. The Si4707 devices are high-performance RF integrated circuits with certain pins having an ESD rating of < 2 kV HBM. Handling and assembly of these devices should only be done at ESD-protected workstations. 3. For input pins SCLK, SEN, SDIO, RST, RCLK, GPO1, GPO2, and GPO3. 4. At RF input pins, FMI. 4 Rev. 0.8 Si4707-B20 Table 3. DC Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 C) Parameter Symbol Min Typ Max Unit IFM — 19.1 23 mA IIO — 320 600 µA VDD Powerdown Current IDDPD — 10 20 µA VIO Powerdown Current1 IIOPD — 1 10 µA Supply Current Interface Supply Current 1 Test Condition SCLK, RCLK inactive 2 High Level Input Voltage VIH 0.7 x VIO — — V Low Level Input Voltage2 VIL — — 0.3 x VIO V Current2 IIH VIN = VIO = 3.6 V –10 — 10 µA Low Level Input Current2 IIL VIN = 0 V, VIO = 3.6 V –10 — 10 µA High Level Output Voltage3 VOH IOUT = 500 µA 0.8 x VIO — — V Low Level Output Voltage3 VOL IOUT = –500 µA — — 0.2 x VIO V High Level Input Notes: 1. Specifications are guaranteed by characterization. 2. For input pins SCLK, SEN, SDIO, RST, and RCLK. 3. For output pins SDIO, GPO1, GPO2, and GPO3. Rev. 0.8 5 Si4707-B20 Table 4. Reset Timing Characteristics1,2,3 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Min Typ Max Unit RST Pulse Width and GPO1, GPO2/INT Setup to RST tSRST 100 — — µs GPO1, GPO2/INT Hold from RST tHRST 30 — — ns Notes: 1. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is high) does not occur within 300 ns before the rising edge of RST. 2. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the first start condition. 3. When selecting 3-wire or SPI modes, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. 4. If GPO1 and GPO2 are actively driven by the user, then minimum tSRST is only 30 ns. If GPO1 or GPO2 is hi-Z, then minimum tSRST is 100 µs to provide time for on-chip 1 M devices (active while RST is low) to pull GPO1 high and GPO2 low. tSRST RST 70% GPO1 70% GPO2/ INT tHRST 30% 30% 70% 30% Figure 1. Reset Timing Parameters for Busmode Select 6 Rev. 0.8 Si4707-B20 Table 5. 2-Wire Control Interface Characteristics1,2,3 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fSCL 0 — 400 kHz SCLK Low Time tLOW 1.3 — — µs SCLK High Time tHIGH 0.6 — — µs SCLK Input to SDIO Setup (START) tSU:STA 0.6 — — µs SCLK Input to SDIO Hold (START) tHD:STA 0.6 — — µs SDIO Input to SCLK Setup tSU:DAT 100 — — ns SDIO Input to SCLK Hold4,5 tHD:DAT 0 — 900 ns SCLK input to SDIO Setup (STOP) tSU:STO 0.6 — — µs STOP to START Time tBUF 1.3 — — µs SDIO Output Fall Time tf:OUT — 250 ns — 300 ns Cb 20 + 0.1 ----------1pF SDIO Input, SCLK Rise/Fall Time tf:IN tr:IN Cb 20 + 0.1 ----------1pF SCLK, SDIO Capacitive Loading Cb — — 50 pF Input Filter Pulse Suppression tSP — — 50 ns Notes: 1. When VIO = 0 V, SCLK and SDIO are low impedance. 2. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is high) does not occur within 300 ns before the rising edge of RST. 3. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the first start condition. 4. The Si4707 delays SDIO by a minimum of 300 ns from the VIH threshold of SCLK to comply with the minimum tHD:DAT specification. 5. The maximum tHD:DAT has only to be met when fSCL = 400 kHz. At frequencies below 400 kHz, tHD:DAT may be violated as long as all other timing parameters are met. Rev. 0.8 7 Si4707-B20 SCLK 70% SDIO 70% tSU:STA tHD:STA tLOW START tr:IN tHIGH tr:IN tf:IN tSP tSU:STO tBUF 30% 30% tf:IN, tf:OUT tHD:DAT tSU:DAT STOP START Figure 2. 2-Wire Control Interface Read and Write Timing Parameters SCLK A6-A0, R/W SDIO START ADDRESS + R/W D7-D0 ACK DATA D7-D0 ACK DATA ACK Figure 3. 2-Wire Control Interface Read and Write Timing Diagram 8 Rev. 0.8 STOP Si4707-B20 Table 6. 3-Wire Control Interface Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fCLK 0 — 2.5 MHz SCLK High Time tHIGH 25 — — ns SCLK Low Time tLOW 25 — — ns tS 20 — — ns SDIO Input to SCLKHold tHSDIO 10 — — ns SEN Input to SCLKHold tHSEN 10 — — ns SCLKto SDIO Output Valid tCDV Read 2 — 25 ns SCLKto SDIO Output High Z tCDZ Read 2 — 25 ns SCLK, SEN, SDIO, Rise/Fall Time tR, tF — — 10 ns SDIO Input, SEN to SCLKSetup Note: When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SCLK 70% 30% tR tF tHSDIO tS SEN 70% SDIO 70% tHIGH tLOW tHSEN tS 30% A7 30% A6-A5, R/W, A4-A1 A0 D15 D14-D1 Address In D0 Data In Figure 4. 3-Wire Control Interface Write Timing Parameters SCLK 70% SEN 70% 30% tHSDIO tS tCDV tHSEN tCDZ tS 30% 70% SDIO A7 30% A6-A5, R/W, A4-A1 Address In A0 D15 ½ Cycle Bus Turnaround D14-D1 D0 Data Out Figure 5. 3-Wire Control Interface Read Timing Parameters Rev. 0.8 9 Si4707-B20 Table 7. SPI Control Interface Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fCLK 0 — 2.5 MHz SCLK High Time tHIGH 25 — — ns SCLK Low Time tLOW 25 — — ns tS 15 — — ns SDIO Input to SCLKHold tHSDIO 10 — — ns SEN Input to SCLKHold tHSEN 5 — — ns SCLKto SDIO Output Valid tCDV Read 2 — 25 ns SCLKto SDIO Output High Z tCDZ Read 2 — 25 ns SCLK, SEN, SDIO, Rise/Fall Time tR, tF — — 10 ns SDIO Input, SEN to SCLKSetup Note: When selecting SPI mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SCLK 70% 30% tR tHIGH SEN 70% SDIO 70% tS tLOW tF tHSDIO tHSEN tS 30% C7 C6–C1 C0 D7 D6–D1 D0 30% Control Byte In 8 Data Bytes In Figure 6. SPI Control Interface Write Timing Parameters SCLK 70% 30% tCDV tS SEN 70% tHSEN tHSDIO tS 30% tCDZ SDIO 70% C7 C6–C1 C0 D7 D6–D1 D0 30% Control Byte In Bus Turnaround 16 Data Bytes Out (SDIO or GPO1) Figure 7. SPI Control Interface Read Timing Parameters 10 Rev. 0.8 Si4707-B20 Table 8. WB Receiver Characteristics1 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6V, TA = 25 °C) Parameter Symbol Test Condition Min Typ Max Unit 162.4 — 162.55 MHz SINAD = 12 dB — 0.45 — µV EMF ±25 kHz — 55 — dB — 45 — dB fR Input Frequency Sensitivity2,3,4 Adjacent Channel Selectivity Audio S/N2,3,4,5 Audio Frequency Reponse Low –3 dB — — 300 Hz Audio Frequency Reponse High –3 dB 3 — — kHz 100% of message correctly received — 0.45 — µV EMF AFSK Trip Sensitivity6 Notes: 1. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic, Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers. 2. FMOD = 1 kHz. 3. f = 3 kHz. 4. BAF = 300 Hz to 15 kHz, A-weighted. 5. VEMF = 1 mV. 6. f = 4 kHz. Table 9. Reference Clock and Crystal Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit 31.130 32.768 40,000.0 kHz –50 — 50 ppm 1 — 4095 31.130 32.768 34.406 kHz Crystal Oscillator Frequency — 32.768 — kHz Crystal Frequency Tolerance –50 — 50 ppm — — 3.5 pF Reference Clock RCLK Supported Frequency * RCLK Frequency Tolerance REFCLK_PRESCALE REFCLK Crystal Oscillator Board Capacitance *Note: The Si4707 divides the RCLK input by REFCLK_PRESCALE to obtain REFCLK. There are some RCLK frequencies between 31.130 kHz and 40 MHz that are not supported. See AN332, Table 6 for more details. Rev. 0.8 11 Si4707-B20 2. Typical Application Schematic GPO1 NC GPO1 GPO2 GPO3 NP3 20 19 18 17 16 GPO2 GPO3 1 FMI 2 3 4 5 NC NP2 FMI RFGND U1 Si4707-GM NP1 RST LOUT ROUT 15 14 13 12 GND 11 VDD LOUT ROUT VBATTERY 2.7 to 5.5 V RST 6 7 8 9 10 SEN SCLK SDIO RCLK VIO C1 X1 GPO3 SEN SCLK C2 SDIO RCLK VIO 1.5 to 3.6 V RCLK C3 Optional: for crystal oscillator option Notes: 1. Place C1 close to VDD pin. 2. All grounds connect directly to GND plane on PCB. 3. Pins 1 and 20 are no connects, leave floating. 4. Pins 4, 15, and 16 are unused; recommend connecting to ground. 5. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic, Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers. 6. Pin 2 connects to the WB antenna interface. 7. Place Si4707 as close as possible to antenna jack and keep the FMI trace as short as possible. 12 Rev. 0.8 Si4707-B20 3. Bill of Materials Component(s) Value/Description C1 Supply bypass capacitor, 22 nF, ±20%, Z5U/X7R U1 Si4707 WB + SAME Receiver Supplier Murata Silicon Laboratories Optional Components C2, C3 X1 Crystal load capacitors, 22 pF, ±5%, COG (Optional: for crystal oscillator option) Venkel 32.768 kHz crystal (Optional: for crystal oscillator option) Epson Rev. 0.8 13 Si4707-B20 4. Functional Description 4.1. Overview Si4707 Weather Band Antenna ADC FMI RFGND LNA PGA DAC LOUT DAC ROUT GPO GPO DSP ADC AGC 0/90 RSSI / SNR 32.768 kHz VIO XTAL OSC SEN REG CONTROL INTERFACE RST VDD SAME SDIO 2.7–5.5 V AFC SCLK RCLK Figure 8. Functional Block Diagram The Si4707 is the industry's first weather band (WB) radio receiver IC to include a specific area message encoding (SAME) processor. Offering unmatched integration and PCB space savings, the Si4707 requires only one external component and less than 15 mm2 of board area. Available in a tiny 3 x 3 mm QFN package, it eliminates the need for a front-end tuner IC, external ADC, DSP processor, RAM, and numerous discrete components found in traditional SAME weather band radios. The Si4707 weather band receiver provides the space savings and low power consumption necessary for portable devices while delivering the high performance and design simplicity desired for all weather alert radios. Leveraging Silicon Laboratories' proven and patented Si4700/01 FM tuner's digital low intermediate frequency (low-IF) receiver architecture, the Si4707 delivers superior RF performance combined with sophisticated digital processing to yield best-in-class audio quality and SAME data sensitivity. 14 The high integration and complete system production test simplifies design in, increases system quality, and improves manufacturability. The Si4707 is a feature-rich solution including 1050 Hz tone detection, automatic frequency control, dynamic channel bandwidth filters, and digital tuning. In addition, the Si4707 provides a programmable reference clock and supports an I2C compatible 2-wire control interface, SPI, and a Si4700/01 backwards compatible 3-wire control interface. The Si4707 incorporates a digital processor to provide SAME data, advance error correction, and SAME data quality metrics. Using this feature, the Si4707 enables broadcast alert data such as severe thunderstorm warning or flash flood watch to be displayed to the user. Rev. 0.8 Si4707-B20 4.2. Block Diagram Description 4.3. Weather Band Receiver The Si4707 IC integrates the voltage-controlled oscillator (VCO) and frequency synthesizer and accepts a wide-range of programmable reference clocks (RCLK). The IC also supports a dedicated external crystal with an integrated crystal oscillator. The frequency synthesizer generates the quadrature local oscillator signal used to downconvert the RF input to a low intermediate frequency. The VCO frequency is locked to the RCLK and adjusted with an automatic frequency control (AFC) servo loop during reception. The VCO frequency is modified according to the target frequency and varies according to the tuned channel. The Si4707 supports weather band reception from 162.4 to 162.55 MHz. The highly-integrated Si4707 meets NOAA and Weather Radio Canada specifications, receives all seven specified frequencies, implements narrow-band FM de-emphasis, and supports 1050 Hz alert tone detection. In addition, the Si4707 provides advanced features not available on conventional radios, such as an AFC, a dynamic channel bandwidth filter, and RSSI and SNR receive signal quality indicators. The Si4707 uses a digital low-IF architecture, integrating the entire analog receive chain for WB. The IC also integrates the functionality of most external components typically found in competing solutions and performs all processing in an on-chip digital signal processor (DSP) and microcontroller (MCU) core. The analog chain includes a dedicated low-noise amplifier (LNA), automatic gain control (AGC), image-reject quadrature mixer, programmable gain amplifier (PGA), and a set of delta-sigma high-performance ADCs. The LNA block receives wide-band frequency input at the FMI input pin. The on-chip resistor blocks control the gain of the external WB antenna network. The LNA gain is dynamically controlled by the AGC loop, contingent on the RF peak detectors and signal strength. The receive path continues to dedicated quadrature mixers that downconvert the received signal from RF to low-IF, filter for out-of-band interferers, and perform a transfer function to shift the tuned frequency to DC. A single pair of PGAs filters the multiplexed (MPX) mixer output from interferers and amplifies the signal again before delivering it to two high-resolution analog-to-digital converters (ADC). The digital core performs channel selection and filtering, digital calibrated tuning, FM demodulation, and SAME demodulation/decoding. The core also performs signal quality processing including received signal strength indicators (RSSI) and SNR. The AFC locks on to the strongest signal within a narrow, adjustable frequency range to compensate for any potential frequency errors such as crystal tolerance or transmit frequency errors. The AFC ensures the channel filter is always centered on the desired channel providing optimal reception. The dynamic channel bandwidth feature utilizes a wide filter in strong signal conditions to provide best sound quality and a narrower filter in weak conditions to provide best sensitivity. 4.4. DAC High-fidelity stereo digital-to-analog converters (DACs) drive analog audio signals onto the LOUT and ROUT pins. Weather band stations broadcast in mono only, so LOUT and ROUT audio will be the same. The audio output may be muted. Volume is adjusted digitally with the RX_VOLUME property. 4.5. SAME Processor The Si4707 implements a high-performance SAME processor for demodulation, byte-wise data quality metrics, and advanced error correction beyond the commonly used polling method. The SAME decoder draws on soft decision decoding techniques to provide robust performance and delivers reception in environments where signal power is very low or compromised. The Si4707 device stores the entire SAME message and provides a user programmable interrupt at the end of message detected, start of message detected, preamble detected, and/or header buffer ready. It also reports on the confidence level of each byte of data with a value of 0–3, with 3 representing the highest confidence level. This feature, unique to the Si4707, provides extra visibility into the message accuracy, which helps limit the number of false messages in poor reception areas. Rev. 0.8 15 Si4707-B20 4.6. Tuning 4.8. Control Interface The frequency synthesizer uses Silicon Laboratories’ proven technology, including a completely integrated VCO. The frequency synthesizer generates the quadrature local oscillator signal used to downconvert the RF input to a low intermediate frequency. The VCO frequency is locked to the reference clock and adjusted with an AFC servo loop during reception. The tuning frequency can be directly programmed using the WB_TUNE_FREQ. A serial port slave interface is provided, which allows an external controller to send commands to the Si4707 and receive responses from the device. The serial port can operate in three bus modes: 2-wire mode, 3-wire mode, or SPI mode. The Si4707 selects the bus mode by sampling the state of the GPO1 and GPO2 pins on the rising edge of RST. The GPO1 pin includes an internal pull-up resistor, which is connected while RST is low, and the GPO2 pin includes an internal pull-down resistor, which is connected while RST is low. Therefore, it is only necessary for the user to actively drive pins that differ from these states. See Table 10. 4.7. Reference Clock The Si4707 reference clock is programmable, supporting RCLK frequencies in Table 9. Refer to Table 3, “DC Characteristics,” on page 5 for switching voltage levels and Table 8, “WB Receiver Characteristics1,” on page 11 for frequency tolerance information. Using RCLK is the recommended method in order to meet the ±50 ppm requirement. An onboard crystal oscillator is available to generate the 32.768 kHz reference when an external crystal and load capacitors are provided. Refer to "2. Typical Application Schematic" on page 12. This mode is enabled using the POWER_UP command, see Table 11, “Si4707 Command Summary,” on page 19. The Si4707 performance may be affected by data activity on the SDIO bus when using the integrated internal oscillator. SDIO activity results from polling the tuner for status or communicating with other devices that share the SDIO bus. If there is SDIO bus activity while the Si4707 is performing the tune function, the crystal oscillator may experience jitter, which may result in lower SNR. 16 Table 10. Bus Mode Select on Rising Edge of RST Bus Mode GPO1 GPO2 2-Wire 1 0 SPI 1 1 (must drive) 3-Wire 0 (must drive) 0 After the rising edge of RST, the pins GPO1 and GPO2 are used as general purpose output (O) pins as described in Section “4.9. GPO Outputs”. In any bus mode, commands may only be sent after VIO and VDD supplies are applied. In any bus mode, before sending a command or reading a response, the user must first read the status byte to ensure that the device is ready (CTS bit is high). Rev. 0.8 Si4707-B20 4.8.1. 2-Wire Control Interface Mode 4.8.2. 3-Wire Control Interface Mode When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the first start condition. Also, a start condition must not occur within 300 ns before the rising edge of RST. When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. The 2-wire bus mode uses only the SCLK and SDIO pins for signaling. A transaction begins with the START condition, which occurs when SDIO falls while SCLK is high. Next, the user drives an 8-bit control word serially on SDIO, which is captured by the device on rising edges of SCLK. The control word consists of a 7-bit device address, followed by a read/write bit (read = 1, write = 0). The Si4707 acknowledges the control word by driving SDIO low on the next falling edge of SCLK. Although the Si4707 will respond to only a single device address, this address can be changed with the SEN pin (note that the SEN pin is not used for signaling in 2-wire mode). When SEN = 0, the 7-bit device address is 0010001b. When SEN = 1, the address is 1100011b. For write operations, the user then sends an 8-bit data byte on SDIO, which is captured by the device on rising edges of SCLK. The Si4707 acknowledges each data byte by driving SDIO low for one cycle, on the next falling edge of SCLK. The user may write up to eight data bytes in a single 2-wire transaction. The first byte is a command, and the next seven bytes are arguments. For read operations, after the Si4707 has acknowledged the control byte, it will drive an 8-bit data byte on SDIO, changing the state of SDIO on the falling edge of SCLK. The user acknowledges each data byte by driving SDIO low for one cycle, on the next falling edge of SCLK. If a data byte is not acknowledged, the transaction will end. The user may read up to 16 data bytes in a single 2-wire transaction. These bytes contain the response data from the Si4707. A 2-wire transaction ends with the STOP condition, which occurs when SDIO rises while SCLK is high. For details on timing specifications and diagrams, refer to Table 5, “2-Wire Control Interface Characteristics” on page 7; Figure 2, “2-Wire Control Interface Read and Write Timing Parameters,” on page 8, and Figure 3, “2Wire Control Interface Read and Write Timing Diagram,” on page 8. The 3-wire bus mode uses the SCLK, SDIO, and SEN_ pins. A transaction begins when the user drives SEN low. Next, the user drives a 9-bit control word on SDIO, which is captured by the device on rising edges of SCLK. The control word consists of a 3-bit device address (A7:A5 = 101b), a read/write bit (read = 1, write = 0), and a 5-bit register address (A4:A0). For write operations, the control word is followed by a 16-bit data word, which is captured by the device on rising edges of SCLK. For read operations, the control word is followed by a delay of one-half SCLK cycle for bus turn-around. Next, the Si4707 will drive the 16-bit read data word serially on SDIO, changing the state of SDIO on each rising edge of SCLK. A transaction ends when the user sets SEN high, then pulses SCLK high and low one final time. SCLK may either stop or continue to toggle while SEN is high. In 3-wire mode, commands are sent by first writing each argument to register(s) 0xA1–0xA3, then writing the command word to register 0xA0. A response is retrieved by reading registers 0xA8–0xAF. For details on timing specifications and diagrams, refer to Table 6, “3-Wire Control Interface Characteristics,” on page 9; Figure 4, “3-Wire Control Interface Write Timing Parameters,” on page 9, and Figure 5, “3-Wire Control Interface Read Timing Parameters,” on page 9. 4.8.3. SPI Control Interface Mode When selecting SPI mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SPI bus mode uses the SCLK, SDIO, and SEN pins for read/write operations. The system controller can choose to receive read data from the device on either SDIO or GPO1. A transaction begins when the system controller drives SEN = 0. The system controller then pulses SCLK eight times, while driving an 8-bit control byte serially on SDIO. The device captures the data on rising edges of SCLK. The control byte must have one of five values: 0x48 = write a command (controller drives 8 additional bytes on SDIO). 0x80 = read a response (device drives one additional byte on SDIO). 0xC0 = read a response (device drives 16 additional bytes on SDIO). Rev. 0.8 17 Si4707-B20 0xA0 = read a response (device drives one additional byte on GPO1). 0xE0 = read a response (device drives 16 additional bytes on GPO1). For write operations, the system controller must drive exactly eight data bytes (a command and seven arguments) on SDIO after the control byte. The data is captured by the device on the rising edge of SCLK. For read operations, the controller must read exactly one byte (STATUS) after the control byte or exactly 16 data bytes (STATUS and RESP1–RESP15) after the control byte. The device changes the state of SDIO (or GPO1, if specified) on the falling edge of SCLK. Data must be captured by the system controller on the rising edge of SCLK. Keep SEN low until all bytes have transferred. A transaction may be aborted at any time by setting SEN high and toggling SCLK high and then low. Commands will be ignored by the device if the transaction is aborted. For details on timing specifications and diagrams, refer to Figure 6 and Figure 7 on page 10. 4.9. GPO Outputs The Si4707 provides three general-purpose output pins. The GPO pins can be configured to output a constant low, constant high, or high impedance. The GPO pins can be reconfigured as specialized functions. GPO2/INT can be configured to provide interrupts and GPO3 can be configured to provide external crystal support. 4.10. Firmware Upgrades The Si4707 contains on-chip program RAM to accommodate minor changes to the firmware. This allows Silicon Laboratories to provide future firmware updates to optimize the characteristics of new radio designs and those already deployed in the field. 18 4.11. Reset, Powerup, and Powerdown Setting the RST pin low will disable analog and digital circuitry, reset the registers to their default settings, and disable the bus. Setting the RST pin high will bring the device out of reset. A powerdown mode is available to reduce power consumption when the part is idle. Putting the device in powerdown mode will disable analog and digital circuitry while keeping the bus active. 4.12. Programming with Commands To ease development time and offer maximum customization, the Si4707 provides a simple yet powerful software interface to program the receiver. The device is programmed using commands, arguments, properties and responses. To perform an action, the user writes a command byte and associated arguments, causing the chip to execute the given command. Commands control an action such as powerup the device, shut down the device, or tune to a station. Arguments are specific to a given command and are used to modify the command. A complete list of commands is available in Table 11, “Si4707 Command Summary,” on page 19. Properties are a special command argument used to modify the default chip operation and are generally configured immediately after powerup. A complete list of properties is available in Table 12, “Si4707 Property Summary,” on page 20. Responses provide the user information and are echoed after a command and associated arguments are issued. All commands provide a one-byte status update, which indicates interrupt and clear-to-send status information. For a detailed description of the commands and properties for the Si4707, see “AN332: Si47xxProgramming Guide.” Rev. 0.8 Si4707-B20 5. Commands and Properties Table 11. Si4707 Command Summary Cmd Name Description 0x01 POWER_UP 0x10 GET_REV 0x11 POWER_DOWN Powerdown device. 0x12 SET_PROPERTY Sets the value of a property. 0x13 GET_PROPERTY Retrieves a property’s value. 0x14 GET_INT_STATUS Read interrupt status bits. 0x15 PATCH_ARGS Reserved command used for firmware file downloads. 0x16 PATCH_DATA Reserved command used for firmware file downloads. 0x50 WB_TUNE_FREQ 0x52 WB_TUNE_STATUS Queries the status of the previous WB_TUNE_FREQ command. 0x53 WB_RSQ_STATUS Queries the status of the Received Signal Quality (RSQ) of the current channel. 0x54 WB_SAME_STATUS 0x55 WB_ASQ_STATUS Queries the status of the 1050 Hz alert tone. 0x57 WB_AGC_STATUS Queries the status of the AGC. 0x58 WB_AGC_OVERRIDE Enable or disable the WB AGC. 0x80 GPO_CTL Configures GPO3 as output or Hi-Z. 0X81 GPO_SET Sets GPO3 output level (low or high). Powerup device. Returns revision information on the device. Selects the WB tuning frequency. Returns SAME information for the current channel. Rev. 0.8 19 Si4707-B20 Table 12. Si4707 Property Summary Prop Name 0x0001 GPO_IEN 0x0201 REFCLK_FREQ 0x0202 REFCLK_PRESCALE 0x4000 RX_VOLUME 0x4001 RX_HARD_MUTE 0x5108 Description Default Enables interrupt sources. 0x0000 Sets frequency of reference clock in Hz. The range is 31130 to 34406 Hz or 0 to disable the AFC. Default is 32768 Hz. 0x8000 Sets the prescaler value for RCLK input. 0x0001 Sets the output volume. 0x003F Mutes the audio output. L and R audio outputs may be muted independently in FM mode. 0x0000 WB_MAX_TUNE_ERROR Maximum change in frequencies from the WB_TUNE_FREQ to which the AFC will lock. 0x000F 0x5200 WB_RSQ_INTERRUPT_ SOURCE Configures interrupts related to RSQ metrics. All interrupts are disabled by default. 0x0000 0x5201 WB_RSQ_SNR_HIGH_ THRESHOLD Sets high threshold for SNR interrupt. The default is 0 dB. 0x007F 0x5202 WB_RSQ_SNR_LOW_ THRESHOLD Sets low threshold for SNR interrupt. The default is 0 dB. 0x0000 0x5203 WB_RSQ_RSSI_HIGH_ THRESHOLD Sets high threshold for RSSI interrupt. The default is 0 dB. 0x007F 0x5204 WB_RSQ_RSSI_LOW_ THRESHOLD Sets low threshold for RSSI interrupt. The default is 0 dB. 0x0000 0x5600 WB_ASQ_INTERRUPT_ SOURCE Configures 1050 Hz alert tone interrupts. All interrupts are disabled by default. 0x0000 0x5500 WB_SAME_INTERRUPT_ SOURCE Configures SAME interrupt sources. All interrupts are disabled by default. 0x0000 20 Rev. 0.8 Si4707-B20 GPO2/INT GPO3 NP3 1 GPO1 NC NC 6. Pin Descriptions: Si4707-B20 20 19 18 17 16 FMI 2 15 NP2 RFGND 3 14 LOUT GND PAD NP1 4 13 ROUT 6 7 8 9 10 SCLK SDIO RCLK VIO 12 GND SEN RST 5 11 VDD Pin Number(s) Name Description 1, 20 NC No connect. Leave floating. 2 FMI WB RF input. FMI should be connected to the antenna trace. 3 RFGND 4 NP1 Unused. Recommend connect to ground. 5 RST Device reset (active low) input. 6 SEN Serial enable input (active low). 7 SCLK Serial clock input. 8 SDIO Serial data input/output. 9 RCLK External reference oscillator input. 10 VIO I/O supply voltage. 11 VDD Supply voltage. May be connected directly to battery. 12, GND PAD GND Ground. Connect to ground plane on PCB. 13 ROUT Right audio line output in analog. 14 LOUT Left audio line output in analog. 15 NP2 Unused. Recommend connect to ground. 16 NP3 Unused. Recommend connect to ground. 17 GPO3 18 GPO2/INT 19 GPO1 RF ground. Connect to ground plane on PCB. General purpose output or crystal oscillator. General purpose output or interrupt pin. General purpose output. Rev. 0.8 21 Si4707-B20 7. Ordering Guide Part Number* Si4707-B20-GM Description WB Radio and SAME Receiver Package Type Operating Temperature QFN Pb-free –20 to 85 °C *Note: Add an “(R)” at the end of the device part number to denote tape and reel option; 2500 quantity per reel. 22 Rev. 0.8 Si4707-B20 8. Package Markings (Top Marks) 8.1. Top Mark 0720 BTTT YWW 8.2. Top Mark Explanation Mark Method: YAG Laser Line 1 Marking: Part Number 07= Si4707 Firmware Revision 20 = Firmware Revision 2.0 Die Revision B = Revision B Die TTT = Internal Code Internal tracking code Line 2 Marking: Line 3 Marking: Circle = 0.5 mm Diameter Pin 1 Identifier (Bottom-Left Justified) Y = Year WW = Workweek Assigned by the Assembly House. Corresponds to the last significant digit of the year and workweek of the mold date. Rev. 0.8 23 Si4707-B20 9. Package Outline: Si4707 QFN Figure 9 illustrates the package details for the Si4707. Table 13 lists the values for the dimensions shown in the illustration. Figure 9. 20-Pin Quad Flat No-Lead (QFN) Table 13. Package Dimensions Symbol Millimeters Symbol Min Nom Max A 0.50 0.55 0.60 f A1 0.00 0.02 0.05 L 0.35 0.40 0.45 b 0.20 0.25 0.30 L1 0.00 — 0.10 c 0.27 0.32 0.37 aaa — — 0.05 bbb — — 0.05 ccc — — 0.08 ddd — — 0.10 eee — — 0.10 D D2 1.65 1.70 1.75 0.50 BSC E E2 Min 3.00 BSC e 3.00 BSC 1.65 1.70 1.75 Notes: 1. All dimensions are shown in millimeters (mm) unless otherwise noted. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 24 Millimeters Rev. 0.8 Nom Max 2.53 BSC Si4707-B20 10. PCB Land Pattern: Si4707 QFN Figure 10 illustrates the PCB land pattern details for the Si4707-GM. Table 14 lists the values for the dimensions shown in the illustration. Figure 10. PCB Land Pattern Rev. 0.8 25 Si4707-B20 Table 14. PCB Land Pattern Dimensions Symbol Millimeters Min D D2 Symbol Max 2.71 REF 1.60 1.80 Min Max GE 2.10 — W — 0.34 — e 0.50 BSC X E 2.71 REF Y E2 f GD 1.60 1.80 2.53 BSC 2.10 Millimeters 0.28 0.61 REF ZE — 3.31 ZD — 3.31 — Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. 3. This Land Pattern Design is based on IPC-SM-782 guidelines. 4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Notes: Solder Mask Design 1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Notes: Stencil Design 1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 2. The stencil thickness should be 0.125 mm (5 mils). 3. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 4. A 1.45 x 1.45 mm square aperture should be used for the center pad. This provides approximately 70% solder paste coverage on the pad, which is optimum to assure correct component stand-off. Notes: Card Assembly 1. A No-Clean, Type-3 solder paste is recommended. 2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 26 Rev. 0.8 Si4707-B20 11. Additional Reference Resources AN332: Si47xx Programming Guide AN383:Si47xx Antenna, Schematic, Layout, and Design Guidelines AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure AN344: Si4706/07/4x Programming Guide Si47xx Customer Support Site: http://www.mysilabs.com This site contains all application notes, evaluation board schematics and layouts, and evaluation software. NDA is required for access. To request access, register at http://www.mysilabs.com and send user’s first and last name, company, NDA reference number, and mysilabs user name to [email protected]. Silicon Labs recommends an all lower case user name. Rev. 0.8 27 Si4707-B20 DOCUMENT CHANGE LIST Revision 0.1 to Revision 0.8 Updated Table 5, “2-Wire Control Interface Characteristics1,2,3,” on page 7. Updated Table 8, “WB Receiver Characteristics1,” on page 11. Updated Table 11, “Si4707 Command Summary,” on page 19. Updated the title of AN383 to ”Si47xx Antenna, Schematic, Layout, and Design Guidelines.” 28 Rev. 0.8 Si4707-B20 NOTES: Rev. 0.8 29 Si4707-B20 CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: [email protected] Internet: www.silabs.com The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 30 Rev. 0.8