SL28EB719 Data Sheet

SL28EB719
EProClock® Generator for Intel Tunnel Creek & Top Cliff
Features
• 14.318MHz output
• Buffered Reference Clock 25MHz
• Compliant Intel CK505 Clock spec
• Low power push-pull type differential output buffers
• Integrated resistors on differential clocks
• 25MHz Crystal Input or Clock input
• Support Wake-On-LAN (WOL)
• EProClock® Programmable Technology
• Wireless friendly 3-bits slew rate control on
single-ended clocks.
• I2C support with readback capabilities
• Triangular Spread Spectrum profile for maximum
electromagnetic interference (EMI) reduction
• Differential CPU clocks with selectable frequency
• 100MHz Differential SRC clocks
• Industrial Temperature -40oC to 85oC
• 75MHz Differential SATA clocks
• 3.3V Power supply
• 96MHz Differential DOT clock
• 48-pin TSSOP package
• 48MHz USB clock
• Selectable 12 or 48MHz output
CPU
SRC
x2/x3
x2/4
Crystal/
CLKIN
REF [1:0]
PLL 1
(SSC)
CPU
Divider
SRC
FS [ C:A]
PCI
PLL 2
(SSC)
CPU_STP#
Divider
SATA75M / SRC0
ITP_EN
PCI/SRC_STP#
PLL 3
(non-SSC)
DOT96
Divider
CLKREQ[3:1]
48M
SEL_SATA75
PLL 4
(non-SSC)
12 / 48M
Divider
SEL_12_48
14.318M
OTP
SCLK
SDATA
CLKPWRGD/
PD#
Logic Core
VR
x0/x1
x1
48M
48M/12M 33M
x1/2
x1
x2
25M
14.318M
x1
x1
Pin Configuration
Block Diagram
XIN
XOUT
SATA75 DOT96
NC
NC
CLKREQ#1**
CLKREQ#2**
PCI0 / SEL_SATA75**
GND_PCI
VDD_PCI
PCIF / ITP_EN**
CLKREQ#3**
12M_48M / SEL12_48*
VDD_48
48M / FSA**
GND_48
DOT96
DOT96#
FSB**
GND_SATA
SATA75M / SRC0
SATA75M# / SRC0#
VDD_SATA
SRC1
SRC1#
SRC2
SRC2#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
NC
GND_14
14M / FSC**
VDD_14
CKPWRGD/WOL_STP#/PD#
VDD_SUSPEND
25MHz
GND_REF
XIN
XOUT
PCI/SRC_STP#*
CPU_STP#*
SDATA
SCLK
GND_CPU
CPU0
CPU0#
VDD_CPU
CPU1
CPU1#
CPU2 / SRC6
CPU2# / SRC6#
VDD_SRC
25 GND_SRC
* Internal 100K-ohm pull-up resistor
** Internal 100K-ohm pull down resistor
DOC#: SP-AP-0005 (Rev. AB)
400 West Cesar Chavez, Austin, TX 78701
1+(512) 416-8500
1+(512) 416-9669
Page 1 of 22
www.silabs.com
SL28EB719
48-TSSOP Pin Definitions
Pin No.
Name
Type
NC
Description
1
NC
2
NC
3
CLKREQ#1**
4
CLKREQ#2**
5
PCI0 / SEL_SATA75**
6
GND_PCI
GND
Ground for PCI clocks
7
VDD_PCI
PWR
3.3V Power supply for PCI clocks
8
PCIF / ITP_EN**
9
CLKREQ#3**
10
12_48M / SEL12_48*
11
VDD_48
12
48M / FSA**
13
GND_48
14
DOT96
O, DIF Fixed true 96MHz clock output
15
DOT96#
O, DIF Fixed complement 96MHz clock output
16
FSB**
NC
No Connect.
No Connect.
I, PD
3.3V clock request input (internal 100K-ohm pull-down)
I, PD
3.3V clock request input (internal 100K-ohm pull-down)
I/O, SE 33MHz clock output/3.3V LVTTL input to enable 75MHz SATA (internal
PD
100K-ohm pull-down)
0 = SATA75/SRC0 = 100MHz, 1 = SATA75/SRC0 = 75MHz
I/O, SE, 33 MHz free running clock output/3.3V LVTTL input to enable SRC6 or
PD
CPU2_ITP (sampled on the CKPWRGD assertion)
0= SRC6, 1= CPU2
I, PD
3.3V clock request input (internal 100K-ohm pull-down)
I/O, SE 12 MHz/ 48MHz Clock output/3.3V-tolerance input for 12MHz or 48MHz
PU
selection (Sampled at CKPWRGD assertion) (internal 100K-ohm pull-up)
0 = 48M, 1 = 12M
PWR
I/O
PD
GND
3.3V Power supply for 48MHz clocks
Fixed 48 MHz clock output/3.3V-tolerant input for CPU frequency selection
(internal 100K-ohm pull-down)
Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications.
Ground for 48MHz clocks
I, PD
3.3V-tolerant input for CPU frequency selection (internal 100K-ohm pull-down)
Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications.
GND
Ground for SATA clock
17
GND_SATA
18
SRC0 / SATA_75M
O, DIF 75MHz or 100MHz True differential serial reference clock
19
SRC0# / SATA_75M#
O, DIF 75MHz or 100MHz Complement differential serial reference clock
20
VDD_SATA
21
SRC1
O, DIF 100MHz True differential serial reference clock
22
SRC1#
O, DIF 100MHz Complement differential serial reference clock
23
SRC2
O, DIF 100MHz True differential serial reference clock
24
SRC2#
O, DIF 100MHz Complement differential serial reference clock
25
GND_SRC
GND
Ground for SRC clocks
26
VDD_SRC
PWR
3.3V Power supply for SRC clocks
27
SRC6# / CPU2#_ITP
O, DIF Selectable complementary differential CPU or SRC clock output.
ITP_EN = 0 @ CK_PWRGD assertion = SRC6
ITP_EN = 1 @ CK_PWRGD assertion = CPU2
28
SRC6 / CPU2_ITP,
O, DIF Selectable True differential CPU or SRC clock output.
ITP_EN = 0 @ CK_PWRGD assertion = SRC6
ITP_EN = 1 @ CK_PWRGD assertion = CPU2
PWR
3.3V Power supply for SATA clock
29
CPU1#
O, DIF Complement differential CPU clock output
30
CPU1
O, DIF True differential CPU clock output
31
VDD_CPU
32
CPU0#
O, DIF Complement differential CPU clock output
33
CPU0
O, DIF True differential CPU clock output
34
GND_CPU
DOC#: SP-AP-0005 (Rev. AB)
PWR
GND
3.3V Power supply for CPU clocks
Ground for clocks
Page 2 of 22
SL28EB719
48-TSSOP Pin Definitions
Pin No.
Name
35
SCLK
Type
I
Description
36
SDATA
I/O
37
CPU_STOP#*
I, PU
3.3V-tolerant input for stopping CPU outputs (internal 100K-ohm pull-up)
38
PCI_STOP#*
I, PU
3.3V-tolerant input for stopping PCI and SRC outputs (internal 100K-ohm
pull-up)
39
XOUT
40
XIN
41
GND_REF
42
25MHz
43
VDD_SUSPEND
44
CKPWRGD/WOL_STP#/PD#
45
VDD_14
46
14.318M / FSC**
47
GND_14
48
NC
SMBus compatible SCLOCK
SMBus compatible SDATA
O
25.00MHz Crystal output
I
25.00MHz Crystal input
GND
O
PWR
I
PWR
Ground for REF clock
25MHz reference output clock
3.3V Power Supply for REF clock and power to support WOL
3.3V LVTTL input. This pin is a level sensitive strobe used to determine
when latch inputs are valid and are ready to be sampled /
Asynchronous active low input pin that stops all outputs except free running
25MHz when WOL_EN = “1” (Byte 1 bit 1)
This pin becomes a real-time active low input for asserting power down (PD#)
when WOL_EN = “0” (Byte 1 bit 1).
3.3V Power supply for 14.318MHz clock
I/O, PD Fixed 14.318MHz clock output/3.3V-tolerant input for CPU frequency selection
(internal 100K-ohm pull-down)
Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications.
GND
NC
Ground for 14.318MHz clock
No Connect.
PC EProClock® Programmable Technology
PC EProClock® is the world’s first non-volatile programmable
PC clock. The PC EProClock® technology allows board
designer to promptly achieve optimum compliance and clock
signal integrity; historically, attainable typically through device
and/or board redesigns.
- Custom frequency sets
PC EProClock® technology can be configured through SMBus
or hard coded.
- Differential and single-ended slew rate control
- Differential skew control on true or compliment or both
- Differential duty cycle control on true or compliment or both
- Differential amplitude control
Features:
- Program Internal or External series resistor on single-ended
clocks
- > 4000 bits of configurations
- Program different spread profiles
- Can be configured through SMBus or hard coded
- Program different spread modulation rate
DOC#: SP-AP-0005 (Rev. AB)
Page 3 of 22
SL28EB719
Frequency Select Pin (FS)
SEL_SATA
FSC
FSB
FSA
CPU
SRC
SATA
PCI
0
0
0
0
100.00
100.00
100.00
33.33
0
0
0
1
100.00
100.00
100.00
33.33
0
0
1
0
83.33
100.00
100.00
33.33
0
0
1
1
83.33
100.00
100.00
33.33
0
1
0
0
133.33
100.00
100.00
33.33
0
1
0
1
133.33
100.00
100.00
33.33
0
1
1
0
166.67
100.00
100.00
33.33
0
1
1
1
166.67
100.00
100.00
33.33
1
0
0
0
100.00
100.00
75.00
33.33
1
0
0
1
100.00
100.00
75.00
33.33
1
0
1
0
83.33
100.00
75.00
33.33
1
0
1
1
83.33
100.00
75.00
33.33
1
1
0
0
133.33
100.00
75.00
33.33
1
1
0
1
133.33
100.00
75.00
33.33
1
1
1
0
166.67
100.00
75.00
33.33
1
1
1
1
166.67
100.00
75.00
33.33
Frequency Select Pin FS
Apply the appropriate logic levels to FS inputs before
CKPWRGD assertion to achieve host clock frequency
selection. When the clock chip sampled HIGH on CKPWRGD
and indicates that VTT voltage is stable then FS input values
are sampled. This process employs a one-shot functionality
and once the CKPWRGD sampled a valid HIGH, all other FS,
and CKPWRGD transitions are ignored except in test mode.
Wake-On-LAN (WOL) Support
When power is applied to the VDD_SUSPEND pin, the 25MHz
reference clock output will be enabled under all conditions,
unless the WOL_EN bit, Byte 1 bit 1, is set to “0”. When the
WOL_EN bit Byte 1 bit 1, is set to “0”, the WOL_STP# pin will
function as a PD# pin. By default, the WOL_EN bit is enabled
and set to a “1”. The clock device will support “out-of-the-box”
WOL or after a power outage by enabling the 25MHz reference
clock output when the clock device powers up for the very first
time with only power applied to the VDD_SUSPEND pin and
all other VDD pins power have not been applied.
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers are individually enabled or disabled. The
registers associated with the Serial Data Interface initialize to
their default setting at power-up. The use of this interface is
optional. Clock device register changes are normally made at
system initialization, if any are required. The interface cannot
be used during system operation for power management
functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, access the bytes in sequential
order from lowest to highest (most significant bit first) with the
ability to stop after any complete byte is transferred. For byte
write and byte read operations, the system controller can
access individually indexed bytes. The offset of the indexed
byte is encoded in the command code described in Table 1.
The block write and block read protocol is outlined in Table 2
while Table 3 outlines byte write and byte read protocol. The
slave receiver address is 11010010 (D2h).
Table 1. Command Code Definition
Bit
7
(6:0)
Description
0 = Block read or block write operation, 1 = Byte read or byte write operation
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000'
DOC#: SP-AP-0005 (Rev. AB)
Page 4 of 22
SL28EB719
Table 2. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
8:2
9
10
18:11
19
27:20
28
36:29
37
45:38
Description
Start
Block Read Protocol
Bit
1
Slave address–7 bits
Write
8:2
9
Acknowledge from slave
Command Code–8 bits
10
18:11
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Acknowledge from slave
19
Acknowledge from slave
Byte Count–8 bits
20
Repeat start
Acknowledge from slave
Data byte 1–8 bits
Acknowledge from slave
Data byte 2–8 bits
27:21
Read = 1
29
Acknowledge from slave
37:30
46
Acknowledge from slave
....
Data Byte /Slave Acknowledges
....
Data Byte N–8 bits
....
Acknowledge from slave
....
Stop
Slave address–7 bits
28
38
46:39
47
55:48
Byte Count from slave–8 bits
Acknowledge
Data byte 1 from slave–8 bits
Acknowledge
Data byte 2 from slave–8 bits
56
Acknowledge
....
Data bytes from slave / Acknowledge
....
Data Byte N from slave–8 bits
....
NOT Acknowledge
....
Stop
Table 3. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
8:2
9
10
18:11
19
27:20
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Byte Read Protocol
Bit
1
8:2
9
10
18:11
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Acknowledge from slave
19
Acknowledge from slave
Data byte–8 bits
20
Repeated start
28
Acknowledge from slave
29
Stop
27:21
28
29
37:30
DOC#: SP-AP-0005 (Rev. AB)
Slave address–7 bits
Read
Acknowledge from slave
Data from slave–8 bits
38
NOT Acknowledge
39
Stop
Page 5 of 22
SL28EB719
Control Registers
Byte 0: Control Register 0
Bit
@Pup
Name
Description
7
0
RESERVED
RESERVED
6
0
RESERVED
RESERVED
5
0
Spread Enable
4
HW
SEL_SATA
See Table 1 for SATA/SRC selection.
3
0
RESERVED
RESERVED
2
HW
FSC
1
HW
FSB
0
HW
FSA
Enable spread for CPU/SRC/PCI outputs
0=Disable, 1= -0.5%
See Table 1 for CPU Frequency selection Table
Byte 1: Control Register 1
Bit
@Pup
Name
7
1
DOT96_OE
Output enable for DOT96
0 = Output Disabled, 1 = Output Enabled
Description
6
1
SATA75/SRC0_OE
Output enable for SATA75/SRC0
0 = Output Disabled, 1 = Output Enabled
5
1
CPU2/SRC6_OE
Output enable for CPU2/SRC6
0 = Output Disabled, 1 = Output Enabled
4
1
SRC2
Output enable for SRC2
0 = Output Disabled, 1 = Output Enabled
3
1
SRC1
Output enable for SRC1
0 = Output Disabled, 1 = Output Enabled
2
1
RESERVED
1
1
WOL_EN
0
0
RESERVED
Wake-On-LAN Enable bit
25MHz free running during VDD Suspend (S-states). If this bit is set to 0,
the XTAL OSC will also be powered down in the Suspend States)
RESERVED
Description
RESERVED
Byte 2: Control Register 2
Bit
@Pup
Name
7
1
48M_OE
6
0
RESERVED
5
1
14M_OE
Output enable for 14M
0 = Output Disabled, 1 = Output Enabled
4
1
25M_OE
Output enable for 25M
0 = Output Disabled, 1 = Output Enabled
3
1
12_48M_OE
Output enable for 12_48M
0 = Output Disabled, 1 = Output Enabled
2
1
PCI0_OE
Output enable for PCI0
0 = Output Disabled, 1 = Output Enabled
1
1
PCIF_OE
Output enable for PCIF
0 = Output Disabled, 1 = Output Enabled
0
0
RESERVED
DOC#: SP-AP-0005 (Rev. AB)
Output enable for 48M
0 = Output Disabled, 1 = Output Enabled
RESERVED
RESERVED
Page 6 of 22
SL28EB719
Byte 3: Control Register 3
Bit
@Pup
Name
7
1
CPU1_OE
Output enable for CPU1
0 = Output Disabled, 1 = Output Enabled
Description
6
1
CPU0_OE
Output enable for CPU0
0 = Output Disabled, 1 = Output Enabled
5
0
CLKREQ#_3
Clock request for SRC2
0=Not controlled, 1= Controlled
4
0
CLKREQ#_3
Clock request for SRC6 (does not apply to CPU clock)
0=Not controlled, 1= Controlled
3
0
CLKREQ#_2
Clock request for SRC2
0=Not controlled, 1= Controlled
2
0
CLKREQ#_2
Clock request for SATA75M/SRC0
0=Not controlled, 1= Controlled
1
0
CLKREQ#_1
Clock request for SRC1
0=Not controlled, 1= Controlled
0
0
CLKREQ#_1
Clock request for SATA75M/SRC0
0=Not controlled, 1= Controlled
Byte 4: Control Register 4
Bit
@Pup
Name
7
0
RESERVED
6
0
CPU1
5
HW
12_48M
4
0
CPU2
3
HW
ITP_EN
2
0
RESERVED
1
0
CPU0
0
0
RESERVED
Description
RESERVED
CPU1 Free Run Control
0= Free Running, 1= Stoppable
Selectable 12_48M status
0= 48M, 1=12M
CPU2 Free Run Control
0= Free Running, 1= Stoppable
SelectableCPUe_ITP/ SRC6 status
0= SRC6, 1=CPU2
RESERVED
CPU0 Free Run Control
0= Free Running, 1= Stoppable
RESERVED
Byte 5: Control Register 5
Bit
@Pup
Name
7
0
RESERVED
RESERVED
6
0
RESERVED
RESERVED
5
0
RESERVED
RESERVED
4
1
SATA75/SRC0
SATA75/SRC0 Free Run Control
0= Free Running, 1= Stoppable
3
0
SRC6
SRC6 Free Run Control
0= Free Running, 1= Stoppable
2
0
SRC2
SRC2 Free Run Control
0= Free Running, 1= Stoppable
1
0
SRC1
SRC1 Free Run Control
0= Free Running, 1= Stoppable
0
0
RESERVED
DOC#: SP-AP-0005 (Rev. AB)
Description
RESERVED
Page 7 of 22
SL28EB719
Byte 6: Control Register 6
Bit
@Pup
Name
7
0
CPU_AMP
6
1
CPU_AMP
5
0
SRC_AMP
4
1
SRC_AMP
3
0
DOT96_AMP
2
1
DOT96_AMP
1
0
SATA_AMP
0
1
SATA_AMP
Description
CPU amplitude adjustment
00= 700mV, 01=800mV, 10=900mV, 11= 1000mV
SRC amplitude adjustment
00= 700mV, 01=800mV, 10=900mV, 11= 1000mV
DOT96 amplitude adjustment
00= 700mV, 01=800mV, 10=900mV, 11= 1000mV
SATA75/SRC0 amplitude adjustment
00= 700mV, 01=800mV, 10=900mV, 11= 1000mV
Byte 7: Vendor ID
Bit
@Pup
Name
7
0
Rev Code Bit 3
Revision Code Bit 3
Description
6
0
Rev Code Bit 2
Revision Code Bit 2
5
0
Rev Code Bit 1
Revision Code Bit 1
4
0
Rev Code Bit 0
Revision Code Bit 0
3
1
Vendor ID bit 3
Vendor ID Bit 3
2
0
Vendor ID bit 2
Vendor ID Bit 2
1
0
Vendor ID bit 1
Vendor ID Bit 1
0
0
Vendor ID bit 0
Vendor ID Bit 0
Byte 8: Control Register 8
Bit
@Pup
Name
7
0
BC7
6
0
BC6
5
0
BC5
4
0
BC4
3
1
BC3
2
1
BC2
1
1
BC1
0
1
BC0
Description
Byte count register for block read operation.
The default value for Byte count is 15
In order to read beyond Byte 15, the user should change the byte count
limit.to or beyond the byte that is desired to be read.
Byte 9: Control Register 9
Bit
@Pup
Name
7
1
RESERVED
RESERVED
6
1
RESERVED
RESERVED
5
1
RESERVED
RESERVED
4
0
RESERVED
RESERVED
3
0
RESERVED
RESERVED
2
0
RESERVED
RESERVED
1
0
PCI0
PCI0 Free Run Control
0= Free Running, 1= Stoppable
0
1
PCIF
PCIF Free Run Control
0= Free Running, 1= Stoppable
DOC#: SP-AP-0005 (Rev. AB)
Description
Page 8 of 22
SL28EB719
Byte 10: Control Register 10
Bit
@Pup
Name
Description
7
0
RESERVED
RESERVED
6
0
RESERVED
RESERVED
5
0
RESERVED
RESERVED
4
0
RESERVED
RESERVED
3
0
RESERVED
RESERVED
2
0
RESERVED
RESERVED
1
0
RESERVED
RESERVED
0
0
RESERVED
RESERVED
Byte 11: Control Register 11
Bit
@Pup
Name
7
1
14M_Bit2
6
0
14M_Bit1
5
1
14M_Bit0
4
1
25M_Bit2
3
0
25M_Bit1
2
1
25M_Bit0
1
1
12_48M_Bit2
0
1
12_48M_Bit0
Description
Drive Strength Control - Bit[2:0] Normal mode default ‘101’
Wireless Friendly Mode default to ‘111’
Byte 12: Byte Count
Bit
@Pup
Name
7
1
48M_Bit2
6
0
48M_Bit1
5
1
48M_Bit0
4
1
PCI0_Bit2
3
0
PCI0_Bit1
2
1
PCI0_Bit0
1
0
RESERVED
0
0
12_48M_Bit1
DOC#: SP-AP-0005 (Rev. AB)
Description
Drive Strength Control - Bit[2:0] Normal mode default ‘101’
Wireless Friendly Mode default to ‘111’
Page 9 of 22
SL28EB719
Byte 13: Control Register 13
Bit
@Pup
Name
Description
7
1
PCIF_Bit2
6
0
PCIF_Bit1
Drive Strength Control - Bit[2:0] Normal mode default ‘101’
Wireless Friendly Mode default to ‘111’
5
1
PCIF_Bit0
4
0
RESERVED
RESERVED
3
0
RESERVED
RESERVED
2
0
RESERVED
RESERVED
1
0
RESERVED
0
0
Wireless Friendly mode
RESERVED
Wireless Friendly Mode
0 = Disabled, Default all single-ended clocks slew rate config bits to ‘101’
1 = Enabled, Default all single-ended clocks slew rate config bits to ‘111’
Byte 14: Control Register 14
Bit
@Pup
Name
7
1
RESERVED
RESERVED
Description
6
0
RESERVED
RESERVED
5
1
RESERVED
RESERVED
4
0
OTP_4
3
0
OTP_3
2
0
OTP_2
1
0
OTP_1
0
0
OTP_0
OTP_ID
Idenification for programmed device
.
Table 4. Output Driver Status during CPU_STP# & PCIS_STP#
CPU_STP#
Asserted
Single-ended Clocks Stoppable
Differential Clocks
PCI_STP#
Asserted
CLKREQ#
Asserted
Running
Driven Low
Running
Non stoppable
Running
Running
Running
Stoppable
Clock driven high
Clock driven high
Clock driven low
Clock# driven low
Clock# driven low
Clock# driven low
Running
Running
Running
Non stoppable
SMBus OE Disabled
Driven low
Clock driven low
Table 5. Output Driver Status
All Single-ended Clocks
PD# = 0 (Power down)
All Differential Clocks
w/o Strap
w/ Strap
Clock
Clock#
Low
Hi-z
Low
Low
DOC#: SP-AP-0005 (Rev. AB)
Page 10 of 22
SL28EB719
Table 6. Crystal Recommendations
Frequency
(Fund)
Cut
Loading Load Cap
Drive
(max.)
Shunt Cap
(max.)
Motional
(max.)
Tolerance
(max.)
Stability
(max.)
Aging
(max.)
25.000MHz
AT
Parallel
0.1 mW
5 pF
0.016 pF
35 ppm
30 ppm
5 ppm
20 pF
The SL28EB719 requires a Parallel Resonance Crystal.
Substituting a series resonance crystal causes the
SL28EB719 to operate at the wrong frequency and violates
the ppm specification. For most applications there is a
300-ppm frequency shift between series and parallel crystals
due to incorrect loading.
,
Use the following formulas to calculate the trim capacitor
values for Ce1 and Ce2.
Load Capacitance (each side)
Ce = 2 * CL – (Cs + Ci)
Crystal Loading
Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, use the total capacitance the crystal sees to calculate the appropriate capacitive
loading (CL).
Figure 1 shows a typical crystal configuration using the two
trim capacitors. It is important that the trim capacitors are in
series with the crystal. It is not true that load capacitors are in
parallel with the crystal and are approximately equal to the
load capacitance of the crystal.
Total Capacitance (as seen by the crystal)
CLe
=
1
1
( Ce1 + Cs1
+ Ci1 +
1
Ce2 + Cs2 + Ci2
)
CL....................................................Crystal load capacitance
CLe......................................... Actual loading seen by crystal
using standard value trim capacitors
Ce..................................................... External trim capacitors
Cs .............................................. Stray capacitance (terraced)
Ci ...........................................................Internal capacitance
(lead frame, bond wires, etc.)
PD# (Power down) Clarification
Figure 1. Crystal Capacitive Clarification
Calculating Load Capacitors
In addition to the standard external trim capacitors, consider
the trace capacitance and pin capacitance to calculate the
crystal loading correctly. Again, the capacitance on each side
is in series with the crystal. The total capacitance on both side
is twice the specified crystal load capacitance (CL). Trim
capacitors are calculated to provide equal capacitive loading
on both sides.
The CKPWRGD/PD# pin is a dual-function pin. During initial
power up, the pin functions as CKPWRGD. Once CKPWRGD
has been sampled HIGH by the clock chip, the pin assumes
PD# functionality. The PD# pin is an asynchronous active
LOW input used to shut off all clocks cleanly before shutting
off power to the device. This signal is synchronized internally
to the device before powering down the clock synthesizer. PD#
is also an asynchronous input for powering up the system.
When PD# is asserted LOW, clocks are driven to a LOW value
and held before turning off the VCOs and the crystal oscillator.
PD# (Power down) Assertion
When PD is sampled HIGH by two consecutive rising edges
of CPUC, all single-ended outputs will be held LOW on their
next HIGH-to-LOW transition and differential clocks must held
LOW. When PD mode is desired as the initial power on state,
PD must be asserted HIGH in less than 10 s after asserting
CKPWRGD.
PD# Deassertion
The power up latency is less than 1.8 ms. This is the time from
the deassertion of the PD# pin or the ramping of the power
supply until the time that stable clocks are generated from the
clock chip. All differential outputs stopped in a three-state
condition, resulting from power down are driven high in less
than 300 s of PD# deassertion to a voltage greater than
200 mV. After the clock chip’s internal PLL is powered up and
locked, all outputs are enabled within a few clock cycles of
each clock. Figure 4 is an example showing the relationship of
clocks coming up.
Figure 2. Crystal Loading Example
DOC#: SP-AP-0005 (Rev. AB)
Page 11 of 22
SL28EB719
PD#
CPUT, 133MHz
CPUC, 133MHz
SRCT 100MHz
SRCC 100MHz
USB, 48MHz
DOT96T
DOT96C
PCI, 33 MHz
REF
Figure 3. Power down Assertion Timing Waveform
Ts ta b le
< 1 .8 m s
PD#
C P U T , 1 3 3 MH z
C P U C , 1 3 3 MH z
S R C T 1 0 0 MH z
S R C C 1 0 0 MH z
U S B , 4 8 MH z
D OT 9 6 T
D OT 9 6 C
P C I, 3 3 MH z
Td r iv e _ PW R D N #
<300 s , >2 00m V
REF
Figure 4. Power down Deassertion Timing Waveform
FS _A, FS _B ,FS_C ,FS _D
CKPWRGD
P W R G D _V R M
0.2-0.3 m s
D elay
V D D C lock G en
C lock S tate
C lock O utputs
C lock V C O
S tate 0
W ait for
V TT_PW R G D #
S tate 1
State 2
O ff
O ff
D evice is not affected,
V TT_P W R G D # is ignored
S am ple S els
State 3
On
On
Figure 5. CKPWRGD Timing Diagram
DOC#: SP-AP-0005 (Rev. AB)
Page 12 of 22
SL28EB719
CPU_STP# Assertion
CPU_STP# Deassertion
The CPU_STP# signal is an active LOW input used for
synchronous stopping and starting the CPU output clocks
while the rest of the clock generator continues to function.
When the CPU_STP# pin is asserted, all CPU outputs that are
set with the SMBus configuration to be stoppable are stopped
within two to six CPU clock periods after sampled by two rising
edges of the internal CPUC clock. The final states of the
stopped CPU signals are CPUT = HIGH and CPUC = LOW.
The deassertion of the CPU_STP# signal causes all stopped
CPU outputs to resume normal operation in a synchronous
manner. No short or stretched clock pulses are produced when
the clock resumes. The maximum latency from the
deassertion to active outputs is no more than two CPU clock
cycles.
CPU_STP#
CPUT
CPUC
Figure 6. CPU_STP# Assertion Waveform
CPU_STP#
CPUT
CPUC
CPUT Internal
CPUC Internal
Tdrive_CPU_STP#,10 ns>200 mV
Figure 7. CPU_STP# Deassertion Waveform
PCI/SRC_STP# Assertion
.
The PCI/SRC_STP# signal is an active LOW input used for
synchronously stopping and starting the PCI outputs while the
rest of the clock generator continues to function. The set-up
time for capturing PCI/SRC_STP# going LOW is 10 ns (tSU).
(See Figure 8.) The PCIF and SRC clocks are affected by this
pin if their corresponding control bit in the SMBus register is
set to allow them to be free running. For SRC clocks assertion
description, please refer to CPU_STP# description.
T su
PC I_STP#
PC I_F
PC I
SR C 100M H z
Figure 8. PCI_STP# Assertion Waveform
DOC#: SP-AP-0005 (Rev. AB)
Page 13 of 22
SL28EB719
PCI/SRC_STP# Deassertion
.
The deassertion of the PCI/SRC_STP# signal causes all PCI
and stoppable PCIF to resume running in a synchronous
manner within two PCI clock periods, after PCI/SRC_STP#
transitions to a HIGH level. Simlarly, PCI/SRC_STP#
deassertion will cause stoppable SRC clocks to resume
running. For SRC clocks deassertion description, please refer
to CPU_STP# description.
T su
T drive_ S R C
P C I_S T P #
P C I_F
PCI
SR C 100 M H z
Figure 9. PCI_STP# Deassertion Waveform
.
.
Clock Off to M 1
3.3V
Vcc
2.0V
FSC
T_delay t
CPU_STP#
FSB
FSA
PCI_STP#
CKPWRGD/PD#
Off
CK505 SMBUS
CK505 State
Off
Latches Open
M1
BSEL[0..2]
CK505 Core Logic
Off
PLL1
Locked
CPU1
PLL2 & PLL3
All Other Clocks
REF Oscillator
T_delay2
T_delay3
Figure 10. BSEL Serial Latching
DOC#: SP-AP-0005 (Rev. AB)
Page 14 of 22
SL28EB719
Absolute Maximum Conditions
Parameter
Description
Condition
VDD_3.3V
Main Supply Voltage
Functional
VIN
Input Voltage
Relative to VSS
TS
Temperature, Storage
Non-functional
TA
Temperature, Operating
Ambient
Functional
Min.
Max.
Unit
–
4.6
V
–0.5
4.6
VDC
–65
150
°C
–40
85
°C
TJ
Temperature, Junction
Functional
–
150
°C
ØJC
Dissipation, Junction to Case
JEDEC (JESD 51)
–
20
°C/
W
ØJA
Dissipation, Junction to Ambient JEDEC (JESD 51)
–
60
°C/
W
ESDHBM
ESD Protection (Human Body
Model)
JEDEC (JESD 22 - A114)
2000
–
V
UL-94
Flammability Rating
UL (Class)
Max.
Unit
3.135
3.465
V
2.0
VDD + 0.3
V
VSS – 0.3
0.8
V
2.2
–
V
V–0
Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
DC Electrical Specifications
Parameter
Description
Condition
VDD core
3.3V Operating Voltage
VIH
3.3V Input High Voltage (SE)
3.3 ± 5%
VIL
3.3V Input Low Voltage (SE)
VIHI2C
Input High Voltage
SDATA, SCLK
VILI2C
Input Low Voltage
SDATA, SCLK
VIH_FS
FS Input High Voltage
VIL_FS
FS Input Low Voltage
IIH
Input High Leakage Current
Except internal pull-down resistors, 0 < VIN <
VDD
IIL
Input Low Leakage Current
Except internal pull-up resistors, 0 < VIN < VDD
VOH
3.3V Output High Voltage (SE) IOH = –1 mA
VOL
3.3V Output Low Voltage (SE)
IOZ
Min.
–
1.0
V
0.7
VDD+0.3
V
VSS – 0.3
0.35
V
–
5
A
–5
–
A
2.4
–
V
–
0.4
V
High-impedance Output
Current
–10
10
A
CIN
Input Pin Capacitance
1.5
COUT
Output Pin Capacitance
LIN
Pin Inductance
VXIH
Xin High Voltage
VXIL
Xin Low Voltage
0
0.3VDD
V
IDD_PD
Power Down Current
–
1
mA
IDD_3.3V
Dynamic Supply Current
–
130
mA
DOC#: SP-AP-0005 (Rev. AB)
IOL = 1 mA
All outputs enabled. SE clocks with 8” traces.
Differential clocks with 7” traces. Loading per
CK505 spec.
5
pF
6
pF
–
7
nH
0.7VDD
VDD
V
Page 15 of 22
SL28EB719
AC Electrical Specifications
Parameter
Description
Condition
Min.
Max.
Unit
47.5
52.5
%
69.841
71.0
ns
–
10.0
ns
Crystal
TDC
XIN Duty Cycle
The device will operate reliably with input
duty cycles up to 30/70 but the REF clock
duty cycle will not be within specification
TPERIOD
XIN Period
When XIN is driven from an external
clock source
TR/TF
XIN Rise and Fall Times
Measured between 0.3VDD and 0.7VDD
TCCJ
XIN Cycle to Cycle Jitter
As an average over 1-s duration
–
500
ps
LACC
Long-term Accuracy
Measured at VDD/2 differential
–
250
ppm
LACC
Long-term Accuracy
Measured at VDD/2 differential
–
250
ppm
Clock Input
TDC
CLKIN Duty Cycle
Measured at VDD/2
47
53
%
TR/TF
CLKIN Rise and Fall Times
Measured between 0.2VDD and 0.8VDD
0.5
4.0
V/ns
TCCJ
CLKIN Cycle to Cycle Jitter
Measured at VDD/2
–
250
ps
TLTJ
CLKIN Long Term Jitter
Measured at VDD/2
–
350
ps
VIL
Input Low Voltage
XIN / CLKIN pin
–
0.8
V
VIH
Input High Voltage
XIN / CLKIN pin
2
VDD+0.3
V
IIL
Input LowCurrent
XIN / CLKIN pin, 0 < VIN <0.8
–
20
uA
IIH
Input HighCurrent
XIN / CLKIN pin, VIN = VDD
–
35
uA
TDC
CPU Duty Cycle
Measured at 0V differential
TPERIOD
83.33 MHz CPU Period
TPERIODSS
83.33 MHz CPU Period, SSC
TPERIODAbs
83.33 MHz CPU Absolute Period
CPU at 0.7V
45
55
%
Measured at 0V differential at 0.1s
11.99880
12.00120
ns
Measured at 0V differential at 0.1s
12.028872
12.03128
ns
Measured at 0V differential at 1clock
11.18969
12.16344
ns
TPERIODSSAbs 83.33 MHz CPU Absolute Period, SSC Measured at 0V differential at 1 clock
11.89687
12.16344
ns
TPERIOD
100 MHz CPU Period
Measured at 0V differential at 0.1s
9.99900
10.0010
ns
TPERIODSS
100 MHz CPU Period, SSC
Measured at 0V differential at 0.1s
10.02406
10.02607
ns
TPERIODAbs
100 MHz CPU Absolute Period
10.1260
ns
Measured at 0V differential at 1clock
9.87400
TPERIODSSAbs 100 MHz CPU Absolute Period, SSC
Measured at 0V differential at 1 clock
9.87406
10.1762
ns
TPERIOD
133 MHz CPU Period
Measured at 0V differential at 0.1s
7.49925
7.50075
ns
TPERIODSS
133 MHz CPU Period, SSC
Measured at 0V differential at 0.1s
7.51804
7.51955
ns
TPERIODAbs
133 MHz CPU Absolute period
7.58575
ns
Measured at 0V differential at 1 clock
7.41425
TPERIODSSAbs 133 MHz CPU Absolute period, SSC
Measured at 0V differential at1 clock
7.41430
7.62340
ns
TPERIOD
166 MHz CPU Period
Measured at 0V differential at 0.1s
5.99940
6.00060
ns
TPERIODSS
166 MHz CPU Period, SSC
Measured at 0V differential at 0.1s
6.01444
6.01564
ns
TPERIODAbs
166 MHz CPU Absolute period
6.08560
ns
6.11572
ns
Measured at 0V differential at 1 clock
5.91440
TPERIODSSAbs 166 MHz CPU Absolute period, SSC
Measured at 0V differential at 1 clock
5.91444
TCCJ
CPU Cycle to Cycle Jitter
Measured at 0V differential
–
85
ps
TCCJ (CPU2)
CPU Cycle to Cycle Jitter for CPU 2
Measured at 0V differential
–
125
ps
Skew
CPU0 to CPU1 skew
Measured at 0V differential
–
100
ps
LACC
Long-term Accuracy
Measured at 0V differential
–
100
ppm
T R / TF
CPU Rising/Falling Slew rate
Measured differentially from ±150 mV
2.5
8
V/ns
TRFM
Rise/Fall Matching
Measured single-endedly from ±75 mV
–
20
%
VHIGH
Voltage High
VLOW
Voltage Low
DOC#: SP-AP-0005 (Rev. AB)
–0.3
1.15
V
–
V
Page 16 of 22
SL28EB719
AC Electrical Specifications (continued)
Parameter
VOX
Description
Condition
Crossing Point Voltage at 0.7V Swing
Min.
Max.
Unit
300
550
mV
SRC at 0.7V
TDC
SRC Duty Cycle
Measured at 0V differential
45
55
%
10.0010
ns
TPERIOD
100 MHz SRC Period
Measured at 0V differential at 0.1s
9.99900
TPERIODSS
100 MHz SRC Period, SSC
Measured at 0V differential at 0.1s
10.02406
10.02607
ns
TPERIODAbs
100 MHz SRC Absolute Period
Measured at 0V differential at 1 clock
9.87400
10.1260
ns
Measured at 0V differential at 1 clock
9.87406
10.1762
ns
–
3.0
ns
TPERIODSSAbs 100 MHz SRC Absolute Period, SSC
TSKEW(window) Any SRC Clock Skew from the earliest Measured at 0V differential
bank to the latest bank
TCCJ
SRC Cycle to Cycle Jitter
Measured at 0V differential
–
125
ps
LACC
SRC Long Term Accuracy
Measured at 0V differential
–
100
ppm
T R / TF
SRC Rising/Falling Slew Rate
Measured differentially from ±150 mV
2.5
8
V/ns
TRFM
Rise/Fall Matching
Measured single-endedly from ±75 mV
–
20
%
VHIGH
Voltage High
1.15
V
VLOW
Voltage Low
–0.3
–
V
VOX
Crossing Point Voltage at 0.7V Swing
300
550
mV
DOT96 at 0.7V
TDC
DOT96 Duty Cycle
Measured at 0V differential
45
55
%
TPERIOD
DOT96 Period
Measured at 0V differential at 0.1s
10.4156
10.4177
ns
TPERIODAbs
DOT96 Absolute Period
Measured at 0V differential at 0.1s
10.1656
10.6677
ns
TCCJ
DOT96 Cycle to Cycle Jitter
Measured at 0V differential at 1 clock
–
250
ps
LACC
DOT96 Long Term Accuracy
Measured at 0V differential at 1 clock
–
100
ppm
T R / TF
DOT96 Rising/Falling Slew Rate
Measured differentially from ±150 mV
2.5
8
V/ns
TRFM
Rise/Fall Matching
Measured single-endedly from ±75 mV
–
20
%
VHIGH
Voltage High
1.15
V
VLOW
Voltage Low
–0.3
–
V
VOX
Crossing Point Voltage at 0.7V Swing
300
550
mV
45
55
%
SATA75M at 0.7V
TDC
SATA75M Duty Cycle
Measured at 0V differential
TCCJ
SATA75M Cycle to Cycle Jitter
Measured at 0V differential at 1 clock
–
125
ps
LACC
SATA75M Long Term Accuracy
Measured at 0V differential at 1 clock
–
100
ppm
T R / TF
SATA75M Rising/Falling Slew Rate
Measured differentially from ±150 mV
2.5
8
V/ns
TRFM
Rise/Fall Matching
Measured single-endedly from ±75 mV
–
20
%
VHIGH
Voltage High
1.15
V
VLOW
Voltage Low
–0.3
–
V
VOX
Crossing Point Voltage at 0.7V Swing
300
550
mV
PCI/PCIF at 3.3V
TDC
PCI Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Spread Disabled PCIF/PCI Period
Measurement at 1.5V
29.99700
30.00300
ns
TPERIODSS
Spread Enabled PCIF/PCI Period
Measurement at 1.5V
30.08421
30.23459
ns
TPERIODAbs
Spread Disabled PCIF/PCI Period
Measurement at 1.5V
29.49700
30.50300
ns
TPERIODSSAbs Spread Enabled PCIF/PCI Period
Measurement at 1.5V
29.56617
30.58421
ns
THIGH
Spread Enabled PCIF and PCI high time Measurement at 2V
12.27095
16.27995
ns
TLOW
Spread Enabled PCIF and PCI low time Measurement at 0.8V
11.87095
16.07995
ns
DOC#: SP-AP-0005 (Rev. AB)
Page 17 of 22
SL28EB719
AC Electrical Specifications (continued)
Parameter
Description
Condition
Min.
Max.
Unit
12.27365
16.27665
ns
11.87365
16.07665
ns
1.0
4.0
V/ns
–
250
ps
THIGH
Spread Disabled PCIF and PCI high
time
TLOW
Spread Disabled PCIF and PCI low time Measurement at 0.8V
T R / TF
PCIF/PCI Rising/Falling Slew Rate
Measured between 0.8V and 2.0V
TSKEW
Any PCI clock to Any PCI clock Skew
Measurement at 1.5V
TCCJ
PCIF and PCI Cycle to Cycle Jitter
Measurement at 1.5V
–
300
ps
LACC
PCIF/PCI Long Term Accuracy
Measurement at 1.5V
–
100
ppm
Measurement at 2.V
48M, 12_48M at 3.3V
TDC
Duty Cycle
Measurement at 1.5V
45
55
%
20.83542
ns
TPERIOD
48MHz Period
Measurement at 1.5V
20.83125
TPERIODAbs
48MHz Absolute Period
Measurement at 1.5V
20.48125
21.18542
ns
THIGH
48MHz High time
Measurement at 2V
8.216563
11.15198
ns
TLOW
48MHz Low time
Measurement at 0.8V
7.816563
10.95198
ns
TR / TF (48M) Rising and Falling Edge Rate
Measured between 0.8V and 2.0V
1.0
2.0
V/ns
T R / TF
(12_48M)
Rising and Falling Edge Rate
Measured between 0.8V and 2.0V
1.0
2.0
V/ns
TCCJ
Cycle to Cycle Jitter
Measurement at 1.5V
–
300
ps
LACC
Long Term Accuracy
Measurement at 1.5V
–
100
ppm
25M at 3.3V
TDC
Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Period
Measurement at 1.5V
39.996
40.004
ns
TPERIODAbs
Absolute Period
Measurement at 1.5V
39.32360
40.67640
ns
T R / TF
Rising and Falling Edge Rate
Measured between 0.8V and 2.0V
1.0
4.0
V/ns
TCCJ
Cycle to Cycle Jitter
Measurement at 1.5V
–
300
ps
LACC
Long Term Accuracy
Measured at 1.5V
–
100
ppm
14.318M, at 3.3V
TDC
Duty Cycle
Measurement at 1.5V
45
55
%
TPERIOD
Period
Measurement at 1.5V
69.82033
69.86224
ns
TPERIODAbs
Absolute Period
Measurement at 1.5V
68.83429
70.84826
ns
THIGH
High time
Measurement at 2V
29.97543
38.46654
ns
TLOW
Low time
Measurement at 0.8V
29.57543
38.26654
ns
T R / TF
Rising and Falling Edge Rate
Measured between 0.8V and 2.0V
1.0
4.0
V/ns
TCCJ
Cycle to Cycle Jitter
Measurement at 1.5V
–
500
ps
LACC
Long Term Accuracy
Measurement at 1.5V
–
100
ppm
–
1.8
ms
10.0
–
ns
ENABLE/DISABLE and SET-UP
TSTABLE
Clock Stabilization from Power-up
TSS
Stopclock Set-up Time
Test and Measurement Set-up
For Single Ended Clocks
The following diagram shows the test load configurations for the single-ended output signals.
DOC#: SP-AP-0005 (Rev. AB)
Page 18 of 22
SL28EB719
Figure 11. Single-ended clocks Single Load Configuration
Figure 12. Single-ended Output Signals (for AC Parameters Measurement)
For Differential Clock Signals
This diagram shows the test load configuration for the differential clock signals
Figure 13. 0.7V Differential Load Configuration
DOC#: SP-AP-0005 (Rev. AB)
Page 19 of 22
SL28EB719
Figure 14. Differential Measurement for Differential Output Signals (for AC Parameters Measurement)
Figure 15. Single-ended Measurement for Differential Output Signals (for AC Parameters Measurement)
DOC#: SP-AP-0005 (Rev. AB)
Page 20 of 22
SL28EB719
Ordering Information
Part Number
Package Type
Product Flow
Lead-free
SL28EB719ALI
48-pin TSSOP
Industrial, -40 to 85C
SL28EB719ALIT
48-pin TSSOP– Tape and Reel
Industrial, -40 to 85C
Package Diagrams
48-Lead TSSOP
DOC#: SP-AP-0005 (Rev. AB)
Page 21 of 22
SL28EB719
Document History Page
Document Title: SL28EB719 PC EProClock® Generator for Intel Tunnel Creek & Top Cliff
DOC#: SP-AP-0005 (Rev. AB)
REV.
ECR#
Issue
Date
Orig. of
Change
AA
1458
03/17/10
JMA
Initial Release
AB
1640
06/23/10
JMA
1. Added CLKIN feature
2. Added Period Spec for CPU, SRC, and DOT96
3. Added Cycle-to-cycle jitter spec for CPU2/SRC5 (ITP clock)
4. Removed REF wording from 14.318MHz
5. Reduced IDD to 130mA from 200mA
6. Reduced PCI clocks cycle-to-cycle jitter to 300ps from 500ps
7. Reduced 25MHzclock cycle-to-cycle jitter to 300ps from 500ps
8. Reduced 48/12MHz clocks cycle-to-cycle jitter to 300ps from 350ps
9. Reduced 14.318MHz clock cycle-to-cycle jitter to 500ps from 1000ps
10. Reduced SATA75 clock cycle-to-cycle jitter to 125ps from 250ps
11. Removed skew for 14MHz
12. Updated CPU2 Cycle-to-cycle jitter to be 125ps from 85ps
13. Updated Package information
14. Added PD# label to pin configuration on page 1
15. Updated MIL-STD to JEDEC
16. Removed Prliminary wording
17. Added period spec for 83.33, 133, and 166MHz
18. Updated block diagram
DOC#: SP-AP-0005 (Rev. AB)
Description of Change
Page 22 of 22
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
www.silabs.com/CBPro
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using
or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and
"Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to
make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the
included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses
granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent
of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in
weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,
EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,
ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand
names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com