Trifab™ 451UT Framing System - Architectural Detail Manual

TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
Features
TRIFAB® 451UT is 4-1/2" deep with a 2" sightline
Center Plane glass applications
Flush glazed from either the inside or outside
Screw Spline fabrication
Dual Isolock® lanced and debridged thermal break
Infill options up to 1-1/8" thickness
Permanodic® anodized finishes in 7 choices
Painted finishes in standard and custom choices
Optional Features
• High performance sill flashing
• Acoustical rating per AAMA 1801 and ASTM E 1425
• Project specific U-factors (See Thermal Charts)
Product Applications
•
•
•
•
Storefront, Ribbon Window or Punched Openings
Single-span
Integrated entrance framing allowing Kawneer standard entrances or other
specialty entrances to be incorporated
Kawneer windows or GLASSvent ® are easily incorporated
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
•
•
•
•
•
•
•
•
For specific product applications,
Consult your Kawneer representative.
kawneer.com
1
kawneer.com
© Kawneer Company, Inc., 2012
BLANK PAGE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
TRIFAB® 451UT
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
FEBRUARY, 2012
EC 97911-37
FEBRUARY, 2012
EC 97911-37
3
INDEX (CENTER)
BASIC FRAMING DETAILS (CENTER - Outside Glazed)................. 4
BASIC FRAMING DETAILS (CENTER - Inside Glazed).................... 5
MISCELLANEOUS FRAMING (CENTER).......................................... 6
CURVING & TRIM DETAILS................................................................ 7
260 INSULCLAD ENTRANCE DETAILS ............................................ 8
STOREFRONT GLASSvent ® DETAILS.............................................. 9
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
STOREFRONT GLASSvent ® HARDWARE...................................... 10
8225TL VENT .................................................................................... 11
WINDLOAD / DEADLOAD CHARTS ........................................... 12-15
THERMAL CHARTS .................................................................... 16-22
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TRIFAB® 451UT
kawneer.com
452T-CG-001
5
2
3
2"
(50.8)
2"
(50.8)
4
JAMB
5
VERTICAL
DUAL ISOLOCK THERMAL BREAK
SCREW SPLINE
452T-CG-126
452T-CG-001
451T-CG-002
451-CG-004
2
HORIZONTAL
451-CG-004
3
SILL
452T-CG-021
4-1/2"
(114.3)
452T-CG-014
452T-CG-037
kawneer.com
© Kawneer Company, Inc., 2012
BASIC FRAMING DETAILS (CENTER - Outside Glazed)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
TRIFAB® 451UT
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1
HEAD
2"
(50.8)
ELEVATION IS NUMBER KEYED TO DETAILS
2"
(50.8)
4
2"
(50.8)
SCALE 3" = 1'-0"
1/2"
(12.7)
452T-CG-126
4-1/2"
(114.3)
4
FEBRUARY, 2012
EC 97911-37
1
452T-CG-001
4-1/2"
(114.3)
1/2"
(12.7)
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
1
HEAD
452T-CG-001
kawneer.com
2
HORIZONTAL
2"
(50.8)
2"
(50.8)
4
JAMB
5
VERTICAL
3
SILL
2"
(50.8)
SCALE 3" = 1'-0"
2"
(50.8)
EC 97911-37
2"
(50.8)
452T-CG-126
4-1/2"
(114.3)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FEBRUARY, 2012
TRIFAB® 451UT
452T-CG-003
452T-CG-011
451-CG-004
5
BASIC FRAMING DETAILS (CENTER - Inside Glazed)
1
5
2
3
ELEVATION IS NUMBER KEYED TO DETAILS
DUAL ISOLOCK THERMAL BREAK
SCREW SPLINE
452T-CG-126
451-CG-004
4-1/2"
(114.3)
452T-CG-001
451T-CG-002
451-CG-004
4-1/2"
(114.3)
452T-CG-014
452T-CG-037
TRIFAB® 451UT
FEBRUARY, 2012
MISCELLANEOUS FRAMING (CENTER)
EC 97911-37
452T-CG-013
451T-CG-002
451T-CG-002
451T-CG-002
450-110
STEEL
REINFORCING
2-1/4"
(57.2)
2"
(50.8)
2"
(50.8)
2-1/4" MULLION
W/ STEEL
MEDIUM WEIGHT
MULLION
HEAVY WEIGHT
MULLION
452T-CG-010
452T-CG-540
452T-CG-010
452T-CG-540
400-110
STEEL
REINFORCING
2-1/2"
(63.5)
2-1/2"
(63.5)
TUBULAR
EXPANSION MULLION
TUBULAR
EXPANSION MULLION
WITH OPTIONAL STEEL
kawneer.com
© Kawneer Company, Inc., 2012
452T-CG-012
452T-CG-112
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
SCALE 3" = 1'-0"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
6
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
CURVING & TRIM DETAILS
SCALE 3" = 1'-0"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
1
2"
(50.8)
TYPICAL
CAD Details - SCREW SPLINE
(TF451) = TF_VG_451-SS-Center--CAD.zip
(TF451T)= TF_VG_451T-SS-Center--CAD.zip
175-186
3
175-188
175-187
4-1/2"
(114.3)
TYPICAL
2
CURVING DETAILS
(Center Plane Only)
2
175-190
175-190
175-186
175-191
3
BRAKE METAL
FILLERS
069-271 STOOL TRIM
STOOL TRIM CLIP
WITH HIGH PERFORMANCE
FLASHING
451T-VG-150
Seal over Stool Trim fasteners
to prevent water infiltration.
BRAKE METAL
ADAPTOR AT HORIZONTAL
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
451T-VG-150
BRAKE METAL
FILLERS
451T-VG-150
451T-VG-150
BRAKE METAL
ADAPTOR AT VERTICAL
kawneer.com
7
3/32"
(2.4)
2"
(50.8)
2-1/8"
(54.0)
2-3/16"
(55.6)
9/16"
(14.3)
Door Opening
DOOR
JAMB
4
TYP .
2
BOTTOM
RAIL
3
2-1/4"
(57.2)
2
452T-CG-126
5
452T-CG-001
4-1/2"
(114.3)
3
2-1/8"
(54.0)
1/8"
(3.2)
MEETING
STILES
5
260 INSULCLAD® DOOR
kawneer.com
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1/8"
(3.2)
260 INSULCLAD ENTRANCE DETAILS
© Kawneer Company, Inc., 2012
NOTE: Butt Hung or Offset Pivot Doors Only.
TRANSOM
BAR
3-7/8"
(98.4)
ELEVATION IS NUMBER KEYED
TO DETAILS.
2"
(50.8)
TRIFAB® 451UT
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
11/16"
(17.5)
4
2"
(50.8)
1
Door Opening
HEAD
Door Opening
8
FEBRUARY, 2012
EC 97911-37
SCALE 3" = 1'-0"
TRIFAB® VG 451T CENTER FRAMING SHOWN.
OTHER FRAMING OPTIONS AVAILABLE.
CONSULT YOUR KAWNEER REPRESENTATIVE.
1
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
9
STOREFRONT GLASSvent ® DETAILS
SCALE 3" = 1'-0"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
TRIFAB® 451UT FRAMING SHOWN.
OTHER FRAMING OPTIONS AVAILABLE.
CONSULT YOUR KAWNEER REPRESENTATIVE.
OUTSWING CASEMENT
VERTICAL SECTION
PROJECT-OUT
VERTICAL SECTION
452T-CG-126
452T-CG-001
1
452T-CG-001
1
452T-CG-126
3
5
6
469-407
2
3
7
8
4
ELEVATION IS NUMBER KEYED TO DETAILS
469-407
469-407
451-CG-004
451-CG-004
4
2
452T-CG-037
452T-CG-014
OUTSWING CASEMENT
HORIZONTAL SECTION
PROJECT-OUT
HORIZONTAL SECTION
452T-CG-001
452T-CG-001
452T-CG-001
452T-CG-001
451T-CG-002
469-407
469-407
469-407
451T-CG-002
469-407
451T-CG-002
452T-CG-126
5
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
452T-CG-021
6
7
NOTE: Bronze spacer is recommended when 1" insulating glass is used.
MAXIMUM / MINIMUM SIZES (1" INFILL)
PROJECT-OUT
MAXIMUM 60" x 36"
MINIMUM 14" x 14"
OUTSWING CASEMENT MAXIMUM 36" x 60"
MINIMUM 14" x 14"
kawneer.com
8
TRIFAB® 451UT
FEBRUARY, 2012
STOREFRONT GLASSvent HARDWARE
EC 97911-37
®
STOREFRONT GLASSvent ® HARDWARE SELECTION GUIDE
PROJECT - OUT
OUTSWING CASEMENT
Stainless steel 4-bar hinge
STANDARD
STANDARD
Cast white bronze cam lock
STANDARD
STANDARD
Cast white bronze cam lock with pole ring
OPTIONAL
OPTIONAL
Cast white bronze custodial lock
with removable handle
OPTIONAL
OPTIONAL
Cast white bronze concealed lock
with removable hex key
OPTIONAL
OPTIONAL
Cast white bronze pole/pull ring
OPTIONAL
Pivot-shoe roto-operator
OPTIONAL
OPTIONAL
OPTIONAL
Insect screen
CAM LOCK
REMOVABLE
HANDLE
CONCEALED LOCK
CAM LOCK
WITH POLE RING
PULL RING
PIVOT SHOE ROTO-OPERATOR
INSECT SCREEN
WITH STANDARD WICKET
OPTIONAL
CUSTODIAL
LOCK
STAINLESS STEEL
4 BAR HINGES
INSECT SCREEN
WITH FULL WICKET
kawneer.com
© Kawneer Company, Inc., 2012
Multi-point lock with cast white
bronze locking handle
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
DESCRIPTION
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FEBRUARY, 2012
kawneer.com
TRIFAB® 451UT
EC 97911-37
8225TL VENT
SCALE 3" = 1'-0"
PROJECT-OUT
VERTICAL SECTION
452T-CG-021
1
451-CG-004
8225T•L VENTS SHOWN
NOTE: OTHER VENT TYPES CAN BE
ACCOMMODATED, CONSULT YOUR KAWNEER
REPRESENTATIVE FOR OTHER OPTIONS
469-407
1
3
452T-CG-021
452T-CG-001
451T-CG-002
469-407
3
4
2
ELEVATION IS NUMBER KEYED TO DETAILS
469-407
2
451-CG-004
PROJECT-OUT
HORIZONTAL SECTION
452T-CG-001
469-407
451T-CG-002
4
11
12
TRIFAB® 451UT
WIND LOAD / DEADLOAD CHARTS
FEBRUARY, 2012
EC 97911-37
DEADLOAD CHARTS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Horizontal or deadload limitations are based upon 1/8" (3.2), maximum allowable deflection at the center of an
intermediate horizontal member. The accompanying charts are calculated for 1" (25.4) thick insulating glass or 1/4"
(6.35) thick glass supported on two setting blocks placed at the loading points shown.
kawneer.com
© Kawneer Company, Inc., 2012
Mullions are designed for deflection limitations in accordance with AAMA TIR-A11 of L/175 up to 13'-6" and L/240
+1/4" above 13'-6". These curves are for mullions WITH and WITHOUT HORIZONTALS and are based on engineering
calculations for stress and deflection. Allowable wind load stress for ALUMINUM 15,152 p.s.i. (104MPa), STEEL 30,000
p.s.i. (207MPa.). Charted curves, in all cases are for the limiting value. A 4/3 increase in allowable stress has not been
used to develop these curves. For special situations not covered by these curves, contact your Kawneer representative
for additional information. Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WIND LOAD CHARTS
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
WINDLOAD CHARTS
A = 15 PSF (720 Pa)
B = 20 PSF (960 Pa)
C = 25 PSF (1200 Pa)
D = 30 PSF (1440 Pa)
E = 40 PSF (1920 Pa)
WIDTH IN METERS
1.0
2.0
15
1.0
14
10
3.0
9
8
A
B
7
6
2.0
C
D
E
5
452T-CG-001
3
4
5
6
7
8
WIDTH IN FEET
10
3.0
9
7
A
B
C
D
6
E
8
1
2
3
4
5
6
7
8
WIDTH IN FEET
WIDTH IN METERS
WIDTH IN METERS
2.0
1.0
2.0
15
14
14
3.0
9
HEIGHT IN FEET
10
HEIGHT IN METERS
11
7
A
B
C
6
D
452T-CG-010 / 452T-CG-009
5
E
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
8
2
3
4
5
6
7
WIDTH IN FEET
B
10
C
D
E
9
8
5
4
1
2
3
4
5
6
7
8
WIDTH IN FEET
WITHOUT HORIZONTALS
WIDTH IN METERS
WIDTH IN METERS
1.0
2.0
14
14
13
13
11
10
3.0
9
A
8
B
7
C
6
D
E
5
4
4
5
6
WIDTH IN FEET
7
8
2.0
HEIGHT IN FEET
12
HEIGHT IN METERS
4.0
3
2.0
15
15
2
3.0
2.0
6
WITH HORIZONTALS
1.0
1
A
11
7
2.0
8
12
452T-CG-012
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
4.0
12
11
A
10
9
3.0
B
C
D
E
8
7
2.0
6
5
4
1
2
3
4
5
6
WIDTH IN FEET
7
8
HEIGHT IN METERS
1
4.0
13
HEIGHT IN METERS
4.0
12
kawneer.com
2.0
4
15
HEIGHT IN FEET
11
WITHOUT HORIZONTALS
1.0
HEIGHT IN FEET
12
WITH HORIZONTALS
4
© Kawneer Company, Inc., 2012
4.0
5
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
4
2
HEIGHT IN FEET
11
2.0
15
13
HEIGHT IN METERS
12
13
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WIDTH IN METERS
4.0
13
HEIGHT IN FEET
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
14
WITHOUT HORIZONTALS
HEIGHT IN METERS
WITH HORIZONTALS
1
13
TRIFAB® 451UT
FEBRUARY, 2012
WINDLOAD CHARTS
EC 97911-37
A = 15 PSF (720 Pa)
B = 20 PSF (960 Pa)
C = 25 PSF (1200 Pa)
D = 30 PSF (1440 Pa)
E = 40 PSF (1920 Pa)
2.0
15
14
1.0
14
10
A
9
3.0
B
8
C
D
7
6
2.0
E
2
3
4
5
6
7
8
WIDTH IN FEET
B
C
D
9
8
3.0
E
2.0
5
4
1
2
3
4
5
6
7
8
WIDTH IN FEET
WITHOUT HORIZONTALS
WIDTH IN METERS
WIDTH IN METERS
2.0
1.0
15
2.0
15
14
14
10
3.0
9
8
A
7
B
6
C
D
E
5
2.0
452T-CG-112
3
4
5
6
7
8
WIDTH IN FEET
11
10
7
A
B
C
D
6
E
8
1
2
3
4
5
6
7
8
WIDTH IN FEET
WITHOUT HORIZONTALS
WIDTH IN METERS
WIDTH IN METERS
1.0
2.0
14
14
13
13
11
10
B
9
8
3.0
C
7
D
6
E
5
4
4
5
6
WIDTH IN FEET
7
8
2.0
HEIGHT IN FEET
A
12
HEIGHT IN METERS
4.0
3
2.0
15
15
2
2.0
4
WITH HORIZONTALS
1.0
1
3.0
9
452T-CG-112
with 450-110 STEEL
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
A
12
4.0
B
11
10
C
9
D
8
3.0
E
7
2.0
6
HEIGHT IN METERS
2
12
5
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
4
1
HEIGHT IN FEET
11
HEIGHT IN METERS
12
4.0
13
HEIGHT IN METERS
4.0
13
HEIGHT IN FEET
A
10
WITH HORIZONTALS
1.0
HEIGHT IN FEET
11
6
WINDLOAD CHARTS ARE BASED ON
COMPOSITE PROPERTIES WHICH
ARE CALCULATED IN ACCORDANCE
WITH AAMA TIR-8 AND AAMA 505
4
12
7
452T-CG-013
5
1
HEIGHT IN FEET
11
4.0
13
HEIGHT IN METERS
12
2.0
15
4.0
13
HEIGHT IN FEET
WIDTH IN METERS
5
4
1
2
3
4
5
6
7
8
WIDTH IN FEET
kawneer.com
© Kawneer Company, Inc., 2012
1.0
WITHOUT HORIZONTALS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WIDTH IN METERS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WITH HORIZONTALS
HEIGHT IN METERS
14
HEIGHT IN FEET
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
kawneer.com
7
8
6
2.0
5
3
4
1.0
2
1
0
1
1
2
2
3
3
4
4
5
5
6
1.0
7
10
7
8
6
2.0
5
4
3
1.0
2
1
0
C
B
A
WIDTH IN FEET
6
7
8
HEIGHT IN METERS
1.0
HEIGHT IN METERS
HEIGHT IN FEET
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FEBRUARY, 2012
TRIFAB® 451UT
EC 97911-37
DEADLOAD CHARTS
A = (1/4 POINT LOADING)
B = (1/6 POINT LOADING)
C = (1/8 POINT LOADING)
WITH HORIZONTALS
WIDTH IN METERS
11
2.0
9
3.0
452T-CG-011
C
B
A
WIDTH IN FEET
8
WITH HORIZONTALS
WIDTH IN METERS
11
2.0
9
3.0
452T-CG-021
15
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
THERMAL CHARTS
Project Specific U-factor Example Calculation
15'-8"
2'-0"
9'-6"
7'-0"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
5'-0"
Example Glass U-factor= 0.42 Btu/hr·ft2·oF
Total Daylight Opening = 3(5' x 7') + 3(5' x 2') = 135ft2
Total Projected Area
= (Total Daylight Opening + Total Area of Framing System)
= 15'-8" x 9'-6" = 148.83ft2
Percent of Glass
= (Total Daylight Opening ÷ Total Projected Area)
= (135 ÷ 148.83)100 = 91%
System U-factor vs Percent of Glass Area
0.80
0.70
X
E
0.65
0.60
A
COG
U-factor
0.55
M
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.50
P
0.49
0.45
L
E
0.40
0.35
0.30
0.25
70
75
80
90
91%
85
0.20
Percent of Glass
Based on 91% glass and center of glass (COG) U-factor of 0.42
System U-factor is equal to 0.49 Btu/hr x ft2 x oF
kawneer.com
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.75
95
16
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
COG
U-factor
0.48 (2.73)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
kawneer.com
System U-Factor (Btu/h·ft2·°F)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FEBRUARY, 2012
TRIFAB® 451UT
EC 97911-37
THERMAL CHARTS
Note:
Values in parentheses are metric.
COG=Center of Glass.
Charts are generated per AAMA 507.
System U-Factor for Vision Glass
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
Vision Area / Total Area (%)
17
COG
SHGC
Vision Area / Total Area (%)
COG
VT
System Visible Transmittance (VT) vs Percent of Vision Area
Vision Ares / Total Area (%)
Charts are generated per AAMA 507.
kawneer.com
© Kawneer Company, Inc., 2012
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
TRIFAB® 451UT
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
18
FEBRUARY, 2012
EC 97911-37
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Charts are generated per AAMA 507.
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Glass U-Factor 3
Overall U-Factor 4
0.48
0.52
0.46
0.51
0.44
0.49
0.42
0.48
0.40
0.46
0.38
0.44
0.36
0.43
0.34
0.41
0.32
0.39
0.30
0.38
0.28
0.36
0.26
0.35
0.24
0.33
0.22
0.31
0.20
0.30
SHGC Matrix 2
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.66
0.75
0.66
0.70
0.62
0.70
0.61
0.65
0.58
0.65
0.57
0.60
0.53
0.60
0.53
0.55
0.49
0.55
0.48
0.50
0.45
0.50
0.44
0.45
0.40
0.45
0.39
0.40
0.36
0.40
0.35
0.35
0.31
0.35
0.31
0.30
0.27
0.30
0.26
0.25
0.23
0.25
0.22
0.20
0.18
0.20
0.18
0.15
0.14
0.15
0.13
0.10
0.09
0.10
0.09
0.05
0.05
0.05
0.04
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
NOTE: For glass values that are not listed, linear interpolation is permitted.
1. U-Factors are determined in accordance with NFRC 100.
2. SHGC and VT values are determined in accordance with NFRC 200.
3. Glass properties are based on center of glass values and are obtained from your glass supplier.
4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of
2000mm wide by 2000mm high (78-3/4" by 78-3/4").
kawneer.com
19
System U-Factor for Vision Glass
0.48 (2.73)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
THERMAL CHARTS - WITH STEEL
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TRIFAB® 451UT
Vision Area / Total Area (%)
kawneer.com
© Kawneer Company, Inc., 2012
COG
U-factor
System U-Factor (Btu/h·ft2·°F)
20
FEBRUARY, 2012
EC 97911-37
Note:
Values in parentheses are metric.
COG=Center of Glass.
Charts are generated per AAMA 507.
System VT
© Kawneer Company, Inc., 2012
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FEBRUARY, 2012
kawneer.com
TRIFAB® 451UT
EC 97911-37
COG
SHGC
Vision Ares / Total Area (%)
Charts are generated per AAMA 507.
21
THERMAL CHARTS - WITH STEEL
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Vision Area / Total Area (%)
Charts are generated per AAMA 507.
COG
VT
System Visible Transmittance (VT) vs Percent of Vision Area
TRIFAB® 451UT
FEBRUARY, 2012
EC 97911-37
THERMAL PERFORMANCE MATRIX (NFRC SIZE) - WITH STEEL
Thermal Transmittance 1 (BTU/hr • ft • °F)
Overall U-Factor 4
0.48
0.57
0.46
0.56
0.44
0.54
0.42
0.53
0.40
0.51
0.38
0.49
0.36
0.48
0.34
0.46
0.32
0.45
0.30
0.43
0.28
0.41
0.26
0.40
0.24
0.38
0.22
0.36
0.20
0.35
SHGC Matrix 2
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.66
0.75
0.65
0.70
0.62
0.70
0.61
0.65
0.58
0.65
0.57
0.60
0.53
0.60
0.52
0.55
0.49
0.55
0.48
0.50
0.45
0.50
0.44
0.45
0.40
0.45
0.39
0.40
0.36
0.40
0.35
0.35
0.32
0.35
0.30
0.30
0.27
0.30
0.26
0.25
0.23
0.25
0.22
0.20
0.19
0.20
0.17
0.15
0.14
0.15
0.13
0.10
0.10
0.10
0.09
0.05
0.05
0.05
0.04
NOTE: For glass values that are not listed, linear interpolation is permitted.
1. U-Factors are determined in accordance with NFRC 100.
2. SHGC and VT values are determined in accordance with NFRC 200.
3. Glass properties are based on center of glass values and are obtained from your glass supplier.
4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of
2000mm wide by 2000mm high (78-3/4" by 78-3/4").
kawneer.com
© Kawneer Company, Inc., 2012
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
2
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
22