8 7 6 5 4 3 2 ALUMINUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMP ADAPTABLE, .015 DIAMETER CENTER CONTACT, PRESS-IN D REV • HALF SHROUD/FULL BODY CONFIGURATION FOR INTERFACING TO SMP "BULLET" STYLE ADAPTER SRIFT1006 DOCUMENT REVISIONS CHANGE NO. DATE - INIT RLSE 2008-08-15 J. PETRI A DCN000375 9/26/2008 J. PETRI J. PETRI B DCN000691 7/19/2010 C DCN000899 10/24/2011 CFG APPROVAL • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SMP (SHORT BODY). C 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15. DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (MATCHED SEAL). SHELL (WELD FLANGE): ALUMINUM ALLOY 4047 IN ACCORDANCE WITH AWS A5.8. RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B 194 (NICKEL/GOLD PLATE) C 5. FINISH: FERRULE, PIN AND GROUNDING SPRING: NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488-01, TYPE III, CODE A, .000050/.000100 THICK. 6. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBER INDICATING DETENT TYPE, PIN EXTENSION, DIELECTRIC APPLICATION TYPE AND OPTIONAL PIN END CONFIGURATION: EXAMPLE: SRIFT1006 - FD 130 A F ADD F FOR FLATTENED PIN END CONFIGURATION (SEE DETAIL A) DIELECTRIC APPLICATION TYPE (A-AIR, T-TEFLON) PIN EXTENSION (L) DETENT TYPE (FD -FULL, LD - LIMITED, SB - SMOOTH) BASE NUMBER B B VIEWS SHOWN WITHOUT GROUNDING SPRING UNLESS OTHERWISE SPECIFIED A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH THIRD ANGLE PROJECTION 7 6 5 4 3 WWW.SRIHERMETICS.COM TITLE FEEDTHROUGH, SMP COMPATIBLE, ALUMINUM LASER WELDABLE SIZE DOCUMENT A SCALE FORM 300067 REV - (321) 254-4067 SRI HERMETICS 8:1 2 CAGE CODE SRIFT1006 3PJY7 SHEET 1 REV C 1 OF 2 A 8 6 7 5 4 3 2 SRIFT1006 DOCUMENT .142 L .003 .015 FLAT LENGTH D .207 MAX OVER KNURL D .015 MIN FLAT WIDTH .015±.001 DETAIL A FLATTENED PIN END CONFIGURATION SCALE 20 : 1 A DETENT PIN INSTALL THIS DIRECTION .072±.002 WELD FLANGE C FERRULE VIEW SHOWN WITHOUT RF GROUNDING SPRING STRAIGHT KNURL .190±.002 SHELL .035 (AIR DIELECTRIC APPLICATION) .050 (TEFLON DIELECTRIC APPLICATION) .035 .001 THRU (AIR DIELECTRIC) .049 .001 SHOWN (PTFE DIELECTRIC) .060 .002 X 90 .193 .001 SHOWN .2030 .0005 .100 .002 B .137±.001 .003 MAX BRK UNLESS OTHERWISE SPECIFIED A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH .040 MIN ANNULAR RING REQUIRED FOR LASER WELD NO PLATING ALLOWED THIRD ANGLE PROJECTION RECOMMENDED HOLE DETAIL 6 B RF GROUNDING SPRING PART NUMBER SRIFT1006-GS-A (AIR DIELECTRIC APPLICATION) PART NUMBER SRIFT1006-GS-T (TEFLON DIELECTRIC APPLICATION) SHIPPED UNINSTALLED O NO PLATING 7 .0020±.0005 8X .012 AS REQUIRED FORM 300067 REV - C 8X 45° SRI HERMETICS TITLE FEEDTHROUGH, SMP COMPATIBLE, ALUMINUM LASER WELDABLE SIZE DOCUMENT A SCALE 5 4 3 (321) 254-4067 WWW.SRIHERMETICS.COM 8:1 2 CAGE CODE SRIFT1006 3PJY7 SHEET 1 REV C 2 OF 2 A