8 7 6 5 4 3 2 TITANIUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMPM ADAPTABLE, .012 DIAMETER CENTER CONTACT, PRESS-IN SRIFT1026 DOCUMENT REVISIONS REV DCN REVISION DATE - INIT RLSE 5/13/15 RELEASE APPROVAL Jim Petri 2015.05.14 13:57:39 -04'00' • CONFIGURATION FOR INTERFACING TO SMPM "BULLET" STYLE ADAPTER D D • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SMPM. 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15. DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (MATCHED SEAL). SHELL (WELD FLANGE): TITANIUM UNALLOYED GRADE 2 IN ACCORDANCE WITH ASTM B265 OR B348. RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B 194 (NICKEL/GOLD PLATE) C 5. FINISH: FERRULE AND PIN: NICKEL PLATE PER AMS-QQ-N-290, .000100/.000250 THICK GOLD PLATE PER ASTM B488, TYPE III, CODE A, .000050/.000100 THICK. C GROUNDING SPRING: NICKEL PLATE PER QQ-N-290, .000100/.000250 THICK GOLD PLATE PER ASTM B488, TYPE III, CODE A, .000030/.000050 THICK. 6. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBER INDICATING DETENT TYPE, PIN EXTENSION AND DIELECTRIC APPLICATION TYPE: EXAMPLE: SRIFT1026 - FD 130 A DIELECTRIC APPLICATION TYPE (A-AIR, T-TEFLON) PIN EXTENSION (L) DETENT TYPE (FD -FULL, SB - SMOOTH) BASE NUMBER B B VIEWS SHOWN WITHOUT GROUNDING SPRING A A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION a division of WINCHESTER TITLE FEEDTHROUGH, SMPM COMPATIBLE, TITANIUM LASER WELDABLE SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 (321) 254-4067 www.srihermetics.com SCALE 8:1 2 CAGE CODE SRIFT1026 3PJY7 SHEET 1 REV 1 OF 2 8 6 7 .140 5 3 4 2 SRIFT1026 DOCUMENT L±.003 D D .012±.001 DETENT (.151 MAX OVER KNURL) PIN .057±.002 WELD FLANGE FERRULE STRAIGHT KNURL SHELL VIEW SHOWN WITHOUT RF GROUNDING SPRING INSTALL THIS DIRECTION .139±.002 C C 8X 45° .028 (AIR DIELECTRIC APPLICATION) .040 (TEFLON DIELECTRIC APPLICATION) .0020±.0005 .028 .001 THRU (AIR DIELECTRIC) .039 .001 SHOWN (PTFE DIELECTRIC) .053 .002 X 90 (PTFE DIELECTRIC ONLY) Ø.142 .001 SHOWN Ø.148 .001 SHOWN ØAS SHOWN .005±.002 B 8X .008 RF GROUNDING SPRING, SHIPPED UNINSTALLED PART NUMBER SRIFT1007-GS1, AIR DIELECTRIC PART NUMBER SRIFT1007-GS2, TEFLON DIELECTRIC .135±.001 AS REQUIRED B .070±.002 .020 MIN ANNULAR RING REQUIRED FOR LASER WELD NO PLATING ALLOWED O .003 MAX BRK NO PLATING A A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION RECOMMENDED HOLE DETAIL 7 6 TITLE A 5 4 3 (321) 254-4067 www.srihermetics.com FEEDTHROUGH, SMPM COMPATIBLE, TITANIUM LASER WELDABLE SIZE DOCUMENT DO NOT SCALE DRAWING FORM 300067 REV A a division of WINCHESTER SCALE 8:1 2 CAGE CODE SRIFT1026 3PJY7 SHEET 1 REV 2 OF 2