DCR3640W52

DCR3640W52
Phase Control Thyristor
DS5819-4 February 2014 (LN31295)
FEATURES
KEY PARAMETERS

Double Side Cooling

High Surge Capability
VDRM
IT(AV)
ITSM
dV/dt*
dI/dt
APPLICATIONS
5200V
3550A
49000A
1500V/µs
400A/µs
* Higher dV/dt selections available

High Power Drives

High Voltage Power Supplies

Static Switches
VOLTAGE RATINGS
Part and
Ordering
Number
Repetitive Peak
Voltages
VDRM and VRRM
V
DCR3640W52*
DCR3640W50
DCR3640W48
DCR3640W46
5200
5000
4800
4600
Conditions
Tvj = -40°C to 125°C,
IDRM = IRRM = 300mA,
VDRM, VRRM tp = 10ms,
VDSM & VRSM =
VDRM & VRRM + 100V
respectively
Outline type code: W
Lower voltage grades available.
0
0
5000V @ -40 C, 5200V @ 0 C
(See Package Details for further information)
ORDERING INFORMATION
Fig. 1 Package outline
When ordering, select the required part number
shown in the Voltage Ratings selection table.
For example:
DCR3640W52
Note: Please use the complete part number when ordering
and quote this number in any future correspondence
relating to your order.
1/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
CURRENT RATINGS
Tcase = 60°C unless stated otherwise
Symbol
Parameter
Test Conditions
Max.
Units
3550
A
Double Side Cooled
IT(AV)
Mean on-state current
IT(RMS)
RMS value
-
5576
A
Continuous (direct) on-state current
-
5240
A
IT
Half wave resistive load
SURGE RATINGS
Symbol
ITSM
2
It
Parameter
Surge (non-repetitive) on-state current
Test Conditions
Max.
Units
10ms half sine, Tcase = 125°C
49
kA
VR = 0
12.0
MA s
Min.
Max.
Units
2
I t for fusing
2
THERMAL AND MECHANICAL RATINGS
Symbol
Rth(j-c)
Rth(c-h)
Parameter
Thermal resistance – junction to case
Thermal resistance – case to heatsink
Test Conditions
Double side cooled
DC
-
0.00631
°C/W
Single side cooled
Anode DC
-
0.01115
°C/W
Cathode DC
-
0.01453
°C/W
Double side
-
0.0014
°C/W
-
0.0028
°C/W
-
125
°C
Clamping force 76kN
(with mounting compound)
Blocking VDRM / VRRM
Single side
Tvj
Virtual junction temperature
Tstg
Storage temperature range
-55
125
°C
Fm
Clamping force
68.0
84.0
kN
2/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
DYNAMIC CHARACTERISTICS
Symbol
IRRM/IDRM
Parameter
Test Conditions
Min.
Max.
Units
Peak reverse and off-state current
At VRRM/VDRM, Tcase = 125°C
-
300
mA
dV/dt
Max. linear rate of rise of off-state voltage
To 67% VDRM, Tj = 125°C, gate open
-
1500
V/µs
dI/dt
Rate of rise of on-state current
From 67% VDRM to 2x IT(AV)
Repetitive 50Hz
-
200
A/µs
Gate source 30V, 10,
Non-repetitive
-
400
A/µs
tr < 0.5µs, Tj = 125°C
VT(TO)
rT
tgd
Threshold voltage – Low level
500A to 1700A at Tcase = 125°C
-
0.86
V
Threshold voltage – High level
1700A to 5000A at Tcase = 125°C
-
0.98
V
On-state slope resistance – Low level
500A to 1700A at Tcase = 125°C
-
0.2533
m
On-state slope resistance – High level
1700A to 5000A at Tcase = 125°C
-
0.1886
m
VD = 67% VDRM, gate source 30V, 10
-
3
µs
400
750
µs
2700
6325
µC
Delay time
tr = 0.5µs, Tj = 25°C
tq
Turn-off time
Tj = 125°C, VR = 200V, dI/dt = 1A/µs,
dVDR/dt = 20V/µs linear
QS
Stored charge
IT = 2000A, Tj = 125°C, dI/dt – 1A/µs,
IL
Latching current
Tj = 25°C, VD = 5V
-
3
A
IH
Holding current
Tj = 25°C, RG-K = , ITM = 500A, IT = 5A
-
300
mA
3/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
GATE TRIGGER CHARACTERISTICS AND RATINGS
Symbol
Parameter
Test Conditions
Max.
Units
VGT
Gate trigger voltage
VDRM = 5V, Tcase = 25°C
1.5
V
VGD
Gate non-trigger voltage
At 50% VDRM, Tcase = 125°C
0.4
V
IGT
Gate trigger current
VDRM = 5V, Tcase = 25°C
400
mA
IGD
Gate non-trigger current
At 50% VDRM, Tcase = 125°C
15
mA
CURVES
Instantaneous on-state current TI - (A)
7000
6000
5000
4000
3000
2000
min 125°C
max 125°C
min 25°C
max 25°C
1000
0
0.7
1.2
1.7
2.2
Instantaneous on-state voltage V T - (V)
Fig.2 Maximum & minimum on-state characteristics
VTM EQUATION
VTM = A + Bln (IT) + C.IT+D.IT
Where
A = 0.722818
B = - 0.002455
C = 0.000096
D = 0.010486
these values are valid for Tj = 125°C for IT 100A to 7000A
4/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
130
11
Maximum case temperature, Tcase ( oC )
Mean power dissipation - (kW)
10
9
8
7
6
5
180
4
120
3
90
2
60
1
30
110
100
90
80
70
60
50
40
30
20
10
0
0
0
1000
2000
3000
0
4000
1000
2000
3000
4000
5000
6000
Mean on-state current, IT(AV) - (A)
Mean on-state current, I T(AV) - (A)
Fig.3 On-state power dissipation – sine wave
Fig.4 Maximum permissible case temperature,
double side cooled – sine wave
130
180
120
90
60
30
120
110
100
90
12
11
Mean power dissipation - (kW)
Maximum heatsink temperature, THeatsink - ( oC )
180
120
90
60
30
120
80
70
60
50
40
30
20
10
10
9
8
7
6
d.c.
5
180
4
120
3
90
2
60
30
1
0
0
0
1000
2000
3000
4000
5000
Mean on-state current, IT(AV) - (A)
Fig.5 Maximum permissible heatsink temperature,
double side cooled – sine wave
0
1000
2000
3000
4000
5000
6000
Mean on-state current, IT(AV) - (A)
Fig.6 On-state power dissipation – rectangular wave
5/10
www.dynexsemi.com
DCR3640W52
130
130
Maximum heatsik temperature Theatsink - (oC)
T - (°C)
Maximum permissible case temperature ,case
SEMICONDUCTOR
d.c.
180
120
90
60
30
120
110
100
90
80
70
60
50
40
30
20
10
d.c.
180
120
90
60
30
120
110
100
90
80
70
60
50
40
30
20
10
0
0
0
0
1000 2000 3000 4000 5000 6000 7000
Mean on-state current, IT(AV) - (A)
Mean on-state current, IT(AV) - (A)
Fig.7 Maximum permissible case temperature,
double side cooled – rectangular wave
Fig.8 Maximum permissible heatsink temperature,
double side cooled – rectangular wave
16
Double side cooled
Double Side Cooling
Thermal Impedance, Zth(j-c) - ( °C/kW)
1000 2000 3000 4000 5000 6000 7000
14
Ti (s)
Anode Side Cooling
Anode side cooled
Cathode side cooled
12
3
2.8048
4
1.3305
0.0106818
0.058404
0.3584979
1.1285
1.5197
3.2398
5.7622
0.6312
0.0170581
0.2424644
6.013
15.364
1.4106
2.4667
6.7451
3.9054
0.0158344
0.1786951
3.6201
6.196
Ri (°C/kW)
Ti (s)
Zth =  [Ri x ( 1-exp. (t/ti))]
10
2
1.2993
Ri (°C/kW)
Ti (s)
Cathode Sided Cooling
1
0.8816
Ri (°C/kW)
[1]
8
Rth(j-c) Conduction
6
Tables show the increments of thermal resistance R th(j-c) when the device
operates at conduction angles other than d.c.
4
Double side cooling
Zth (z)
2
0
0.001
0.01
0.1
1
10
100
°
180
120
90
60
30
15
sine.
1.00
1.16
1.33
1.48
1.61
1.66
rect.
0.67
0.97
1.13
1.31
1.51
1.61
Anode Side Cooling
Zth (z)
°
180
120
90
60
30
15
sine.
0.94
1.08
1.23
1.37
1.47
1.52
rect.
0.64
0.91
1.06
1.22
1.38
1.47
Cathode Sided Cooling
Zth (z)
°
180
120
90
60
30
15
sine.
0.95
1.09
1.25
1.38
1.49
1.54
rect.
0.65
0.92
1.07
1.23
1.40
1.49
Time ( s )
Fig.9 Maximum (limit) transient thermal impedance – junction to case (°C/kW)
6/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
Fig.10 Multi-cycle surge current
Fig.11 Single-cycle surge current
600
30,000
Co nditio ns:
T j =125oC, VRpeak ~3100V,
VRM ~ 2100V.
Snubber as appro priate to
co ntro l reverse vo tlages
Reverse recovery current, IRR - (A)
Stored Charge, QS - (uC)
25,000
IRRmax = 69.492*(di/dt)0.7014
20,000
QSmax = 6325*(di/dt)0.4506
15,000
10,000
5,000
QSmin = 2698*(di/dt)0.5396
500
400
300
IRRmin = 44.744*(di/dt)0.7539
200
Conditions:
Tj = 125°C, VRpeak ~
3100V,
VRM ~ 2100V
snubber as appropriate to
control reverse voltages.
100
0
0
5
10
15
20
25
Rate of decay of on-state current, di/dt - (A/us)
0
0
5
10
15
20
25
Rate of decay of on-state current- di/dt - (A/us)
Fig.12 Stored Charge
Fig.13 Reverse recovery current
7/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
Fig14 Gate Characteristics
30
Lower Limit
Upper Limit
5W
10W
20W
50W
100W
150W
-40C
Gate trigger voltage, VGT - (V)
25
20
15
10
5
0
0
1
2
3
4
5
6
7
8
9
10
Gate trigger current, IGT - (A)
Fig. 15 Gate characteristics
8/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
PACKAGE DETAILS
For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
Device
DCR1594SW28
DCR1595SW42
DCR1596SW52
DCR5450W22
DCR4910W28
DCR4100W42
DCR3640W52
DCR3020W65
DCR2510W85
Maximum Minimum
Thickness Thickness
(mm)
(mm)
27.34
26.79
27.57
27.02
27.69
27.14
27.265
26.715
27.34
26.79
27.57
27.02
27.69
27.14
27.95
27.4
28.31
27.76
Lead length: 420mm
Lead terminal connector: M4 ring
Package outline type code: W
Fig.16 Package outline
9/10
www.dynexsemi.com
DCR3640W52
SEMICONDUCTOR
IMPORTANT INFORMATION:
This publication is provided for information only and not for resale.
The products and information in this publication are intended for use by appropriately trained technical personnel.
Due to the diversity of product applications, the information contained herein is provided as a general guide only and does not constitute
any guarantee of suitability for use in a specific application.The user must evaluate the suitability of the product and the completeness of
the product data for the application. The user is responsible for product selection and ensuring all safety and any warning requirements
are met. Should additional product information be needed please contact Customer Service.
Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or typographical
errors. The information is provided without any warranty or guarantee of any kind.
This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it is the
most up to date version and has not been superseded.
The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to property.
The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a product failure or
malfunction.
The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use protective
safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any electric charge
remaining in the product must be discharged and allowed to cool before safe handling using protective gloves.
Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use outside the
product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all semiconductors, this may include
potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or explosion. Appropriate application design
and safety precautions should always be followed to protect persons and property.
Product Status & Product Ordering:
We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for
production. The annotations are as follows:Target Information:
Provisional Information:
Preliminary Information:
No Annotation:
This is the most tentative form of information and represents a very preliminary specification.
No actual design work on the product has been started.
Some initial development work has been performed. The datasheet represents a view of the
end product based on very limited information. Certain details will change.
The product design is complete and final characterisation for volume production is in
progress.The datasheet represents the product as it is now understood but details may change.
The product has been approved for production and unless otherwise notified by Dynex any
product ordered will be supplied to the current version of the data sheet prevailing at the
time of our order acknowledgement.
All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available on request.
Any brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
HEADQUARTERS OPERATIONS
DYNEX SEMICONDUCTOR LIMITED
Doddington Road, Lincoln, Lincolnshire, LN6 3LF
United Kingdom.
Phone: +44 (0) 1522 500500
Fax:
+44 (0) 1522 500550
Web: http://www.dynexsemi.com
 Dynex Semiconductor Ltd.
CUSTOMER SERVICE
Phone: +44 (0) 1522 502753 / 502901
Fax:
+44 (0) 1522 500020
e-mail: [email protected]
Technical Documentation – Not for resale.
10/10
www.dynexsemi.com