Datasheet

SURFACE MOUNT,
HIGH REPEATABILITY,
BROADBAND
CENTIGRID® RELAYS
DPDT
SERIES
DESIGNATION
RELAY TYPE
SGRF100
Repeatable, RF Centigrid ® relay
SGRF103
Sensitive, repeatable, RF Centigrid ® relay
UPPER
STATIONARY
CONTACT
UNIFRAME
LOWER
STATIONARY
CONTACT
ARMATURE
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Storage
–65°C to +125°C
Operating
–55°C to +85°C
Vibration
(General Note 1)
10 g’s to 500 Hz
Shock
(General Note 1)
30 g’s,
6ms half sine
Enclosure
Hermetically sealed
SGRF100
0.09 oz. (2.55g) max.
SGRF103
0.16 oz. (4.5g) max.
© 2007 TELEDYNE RELAYS
The ultraminiature SGRF100 and SGRF103 relays are
designed to provide a practical surface-mount solution with
improved RF signal repeatability over the frequency range.
SGRF100 and SGRF103 relays feature a unique ground
shield that isolates and shields each lead to ensure excellent
contact-to-contact and pole-to-pole isolation. This ground
shield provides a ground interface that results in improved highfrequency performance as well as parametric repeatability. The
SGRF100 and SGRF103 extend performance advantages
over similar RF devices that simply offer formed leads for
surface mounting.
These relays are engineered for use in RF attenuator, RF
switch matrices, ATE and other applications that require
dependable high frequency signal fidelity and performance.
SHOWN WITHOUT GROUND SHIELD
Weight
SGRF100
SGRF103
DESCRIPTION
INTERNAL CONSTRUCTION
Temperature
(Ambient)
SERIES
The SGRF100 and SGRF103 feature:
• High repeatability
• Broader bandwidth
• Metal enclosure for EMI shielding
• High isolation between control and signal paths
• High resistance to ESD
The following unique construction features and manufacturing
techniques provide excellent robustness to environmental
extremes and overall high reliability:
• Uniframe motor design provides high magnetic efficiency
and mechanical rigidity
• Minimum mass components and welded construction
provide maximum resistance to shock and vibration
• Advanced cleaning techniques provide maximum
assurance of internal cleanliness
• Gold-plated precious metal alloy contacts ensure reliable
switching
• Hermetically sealed
(800) 284-7007 • www.teledynerelays.com
SGRF100/SGRF103 Page SGRF100SGRF103\052007\Q1
SERIES SGRF100 AND SGRF103
TYPICAL RF CHARACTERISTICS (See RF Notes)
Isolation Across Contacts (RF Note 4)
Isolation Pole to Pole (RF Note 5)
-20
-20
-30
Isolation (dB)
Isolation (dB)
-30
-40
Normally Closed
-50
-40
Energized
-50
De-energized
-60
Normally open
-70
-60
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
0
6000
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
Frequency (MHz)
Frequency (MHz)
VSWR (RF Note 6)
Insertion Loss (RF Note 6)
0
3.00
2.60
-0.4
-0.6
Normally Closed
2.20
-0.8
VSWR
Insertion Loss (dB)
-0.2
-1
Normally Closed
-1.2
Normally open
1.80
Normally open
-1.4
1.40
-1.6
-1.8
0
1.00
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
0
500
1000
1500
2000
Frequency (MHz)
2500
3000
3500
4000
4500
5000
5500
6000
Frequency (MHz)
SGRF100 Time Response (RF Note 6)
1.1
0.9
90%
Volt
0.7
37ps reference
0.5
82.8ps propagation delay time
0.3
54.7ps pulse rise time
10%
0.1
-0.1
-100
0
100
200
300
400
500
600
700
800
900
Time (ps)
RF NOTES
1. Test conditions: a. Fixture: .031" copper clad, reinforced PTFE, RT/duroid® 6002 with SMA connectors.
(RT/duroid® is a registered trademark of Rogers Corporation.)
b. RF ground shield is soldered to PCB RF ground plane.
c. Room ambient temperature.
d. Terminals not tested were terminated with 50-ohm load.
e. Contact signal level: –10 dBm.
f. No. of test samples: 2.
2. Data presented herein represents typical characteristics and is not intended for use as specification limits.
3. Data is per pole, except for pole-to-pole data.
4. Data is the average from readings taken on all open contacts.
5. Data is the average from readings taken on poles with coil energized and de-energized.
6. Data is the average from readings taken on all closed contacts.
7. Test fixture effect de-embedded from frequency and time response data.
SGRF100/SGRF103 Page Specifications are subject to change without notice
© 2007 TELEDYNE RELAYS
SGRF100SGRF103\052007\Q1
SERIES SGRF100 AND SGRF103
GENERAL ELECTRICAL SPECIFICATIONS (@25°C unless otherwise noted) (Notes 2 & 3)
Contact Arrangement
DPDT
Rated Duty
Continuous
Contact Resistance
0.100 Ω max. initial
Contact Load Rating
Low level: 10 to 50 μA @ 10 to 50 mV
Contact Life Ratings
10,000,000 cycles (typical) at low level
Coil Operating Power
SGRF100-5: 500 mW typical @ nominal rated voltage
SGRF100-12: 369 mW typical @ nominal rated voltage
SGRF103-5: 250 mW typical @ nominal rated voltage
SGRF103-12: 180 mW typical @ nominal rated voltage
Operate Time
SGRF100: 4.0 mS max.
SGRF103: 6.0 mS max.
Release Time
SGRF100: 3.0 mS max.
SGRF103: 3.0 mS max.
Intercontact Capacitance
0.4 pf typical
Insulation Resistance
1,000 MΩ min. between mutually isolated terminals
Dielectric Strength
350 Vrms (60 Hz) @ atmospheric pressure
DETAILED ELECTRICAL SPECIFICATIONS (@25°C)
BASE PART NUMBERS
SGRF100-5/SGRF103-5
SGRF100-12/SGRF103-12
5.0
12.0
SGRF100
50
390
SGRF103
100
800
3.6
9.0
Coil Voltage, Nominal (Vdc)
Coil Resistance (Ohms ±20%)
Pick-up Voltage (Vdc max.)
GENERAL NOTES
1. Relays will exhibit
no contact chatter in
excess of 10 µsec or
transfer in excess of 1
µsec.
2. Unless otherwise
specified, parameters
are initial values.
3. Relays may be
subjected to 260°C,
peak solder reflow
temperature, 1 minute, 3
passes.
4. Butt-lead ends are
coplanar within
.003" (0.08).
5. Application notes
available for PCB
layout and mounting
information.
OUTLINE DIMENSIONS
.335 SQ MAX
(8.51)
SRGF103
.460 MAX
(11.68)
SRGF100
.355 MAX
(9.02)
.063 REF
(1.6)
.375 SQ MAX
(9.52)
.031 REF
(0.79)
+.002
(8) LEADS
.035 REF
(0.89)
7
+.030
4X .397 –.020
.100 ±0.010 TYP
(2.54 ±0.254)
8
Ø.017 –.001
BEFORE
LASER WELD
+0.05
(0.43 –0.025
)
1
6
2
(10.08 +0.76
–0.51 )
5
.100 ±0.010 TYP
(2.54 ±0.254)
4
3
SCHEMATIC – TERMINAL VIEW
Pin numbers for reference only;
not marked on display
NOTES
1. Dimensions are in inches. Metric equivalents shown in parentheses.
2. For best RF performance, solder bottom of RF ground shield to PCB RF ground plane.
© 2007 TELEDYNE RELAYS
(800) 284-7007 • www.teledynerelays.com
RF GROUND
SHIELD
(SEE NOTE 2)
U.S. PATENT PENDING
SGRF100/SGRF103 Page SGRF100SGRF103\052007\Q1