Data Sheet

Freescale Semiconductor
Data Sheet: Technical Data
KE06 Sub-Family Data Sheet
Document Number MKE06P80M48SF0
Rev 3, 5/2014
MKE06P80M48SF0
Supports the following:
MKE06Z64VLD4(R),
MKE06Z128VLD4(R),
MKE06Z64VQH4(R),
MKE06Z128VQH4(R),
MKE06Z64VLH4(R),
MKE06Z128VLH4(R),
MKE06Z64VLK4(R), and
MKE06Z128VLK4(R)
Key features
• Operating characteristics
– Voltage range: 2.7 to 5.5 V
– Flash write voltage range: 2.7 to 5.5 V
– Temperature range (ambient): -40 to 105°C
• Performance
– Up to 48 MHz ARM® Cortex-M0+ core
– Single cycle 32-bit x 32-bit multiplier
– Single cycle I/O access port
• Memories and memory interfaces
– Up to 128 KB flash
– Up to 16 KB RAM
• Clocks
– Oscillator (OSC) - supports 32.768 kHz crystal
or 4 MHz to 24 MHz crystal or ceramic
resonator; choice of low power or high gain
oscillators
– Internal clock source (ICS) - internal FLL with
internal or external reference, 37.5 kHz pretrimmed internal reference for 48 MHz system
clock
– Internal 1 kHz low-power oscillator (LPO)
• System peripherals
– Power management module (PMC) with three
power modes: Run, Wait, Stop
– Low-voltage detection (LVD) with reset or
interrupt, selectable trip points
– Watchdog with independent clock source
(WDOG)
– Programmable cyclic redundancy check module
(CRC)
– Serial wire debug interface (SWD)
– Aliased SRAM bitband region (BIT-BAND)
– Bit manipulation engine (BME)
• Security and integrity modules
– 80-bit unique identification (ID) number per chip
• Human-machine interface
– Up to 71 general-purpose input/output (GPIO)
– Two 32-bit keyboard interrupt modules (KBI)
– External interrupt (IRQ)
• Analog modules
– One up to 16-channel 12-bit SAR ADC,
operation in Stop mode, optional hardware
trigger (ADC)
– Two analog comparators containing a 6-bit
DAC and programmable reference input
(ACMP)
• Timers
– One 6-channel FlexTimer/PWM (FTM)
– Two 2-channel FlexTimer/PWM (FTM)
– One 2-channel periodic interrupt timer (PIT)
– One pulse width timer (PWT)
– One real-time clock (RTC)
Freescale reserves the right to change the detail specifications as may be
required to permit improvements in the design of its products.
© 2013–2014 Freescale Semiconductor, Inc.
• Communication interfaces
– Two SPI modules (SPI)
– Up to three UART modules (UART)
– Two I2C modules (I2C)
– One MSCAN module (MSCAN)
• Package options
– 80-pin LQFP
– 64-pin QFP/LQFP
– 44-pin LQFP
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
2
Freescale Semiconductor, Inc.
Table of Contents
1 Ordering parts...........................................................................4
1.1 Determining valid orderable parts......................................4
2 Part identification......................................................................4
5.2.2
FTM module timing...............................................17
5.3 Thermal specifications.......................................................18
5.3.1
Thermal characteristics.........................................18
2.1 Description.........................................................................4
6 Peripheral operating requirements and behaviors....................20
2.2 Format...............................................................................4
6.1 Core modules....................................................................20
2.3 Fields.................................................................................4
6.1.1
SWD electricals ....................................................20
2.4 Example............................................................................5
6.2 External oscillator (OSC) and ICS characteristics.............21
3 Parameter classification............................................................5
6.3 NVM specifications............................................................23
4 Ratings......................................................................................6
6.4 Analog...............................................................................24
4.1 Thermal handling ratings...................................................6
6.4.1
ADC characteristics...............................................24
4.2 Moisture handling ratings..................................................6
6.4.2
Analog comparator (ACMP) electricals.................26
4.3 ESD handling ratings.........................................................6
6.5 Communication interfaces.................................................27
4.4 Voltage and current operating ratings...............................7
6.5.1
SPI switching specifications..................................27
5 General.....................................................................................7
6.5.2
MSCAN.................................................................30
5.1 Nonswitching electrical specifications...............................7
7 Dimensions...............................................................................30
5.1.1
DC characteristics.................................................7
5.1.2
Supply current characteristics...............................14
8 Pinout........................................................................................31
5.1.3
EMC performance.................................................15
8.1 Signal multiplexing and pin assignments...........................31
5.2 Switching specifications.....................................................16
8.2 Device pin assignment......................................................33
5.2.1
Control timing........................................................16
7.1 Obtaining package dimensions.........................................30
9 Revision history.........................................................................36
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
3
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device, go to freescale.com and perform a part number search for the
following device numbers: KE06Z.
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
2.2 Format
Part numbers for this device have the following format:
Q KE## A FFF R T PP CC N
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Description
Values
Q
Qualification status
KE##
Kinetis family
• KE06
A
Key attribute
• Z = M0+ core
FFF
Program flash memory size
• 128 = 128 KB
R
Silicon revision
T
Temperature range (°C)
PP
Package identifier
• M = Fully qualified, general market flow
• P = Prequalification
• (Blank) = Main
• A = Revision after main
• V = –40 to 105
• LD = 44 LQFP (10 mm x 10 mm)
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
4
Freescale Semiconductor, Inc.
Parameter classification
Field
Description
Values
• QH = 64 QFP (14 mm x 14 mm)
• LH = 64 LQFP (10 mm x 10 mm)
• LK = 80 LQFP (14 mm x 14 mm)
CC
Maximum CPU frequency (MHz)
N
Packaging type
• 4 = 48 MHz
• R = Tape and reel
• (Blank) = Trays
2.4 Example
This is an example part number:
MKE06Z128VLK4
3 Parameter classification
The electrical parameters shown in this supplement are guaranteed by various methods.
To give the customer a better understanding, the following classification is used and the
parameters are tagged accordingly in the tables where appropriate:
Table 1. Parameter classifications
P
Those parameters are guaranteed during production testing on each individual device.
C
Those parameters are achieved by the design characterization by measuring a statistically relevant sample size
across process variations.
T
Those parameters are achieved by design characterization on a small sample size from typical devices under
typical conditions unless otherwise noted. All values shown in the typical column are within this category.
D
Those parameters are derived mainly from simulations.
NOTE
The classification is shown in the column labeled “C” in the
parameter tables where appropriate.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
5
Ratings
4 Ratings
4.1 Thermal handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
—
260
°C
2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.2 Moisture handling ratings
Symbol
MSL
Description
Moisture sensitivity level
Min.
Max.
Unit
Notes
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.3 ESD handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
VHBM
Electrostatic discharge voltage, human body model
–6000
+6000
V
1
VCDM
Electrostatic discharge voltage, charged-device model
–500
+500
V
2
Latch-up current at ambient temperature of 125°C
–100
+100
mA
3
ILAT
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body
Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78D, IC Latch-up Test.
• Test was performed at 125 °C case temperature (Class II).
• I/O pins pass ±100 mA I-test with IDD current limit at 400 mA.
• I/O pins pass +50/-100 mA I-test with IDD current limit at 1000 mA.
• Supply groups pass 1.5 Vccmax.
• RESET pin was only tested with negative I-test due to product conditioning requirement.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
6
Freescale Semiconductor, Inc.
General
4.4 Voltage and current operating ratings
Absolute maximum ratings are stress ratings only, and functional operation at the
maxima is not guaranteed. Stress beyond the limits specified in the following table may
affect device reliability or cause permanent damage to the device. For functional
operating conditions, refer to the remaining tables in this document.
This device contains circuitry protecting against damage due to high static voltage or
electrical fields; however, it is advised that normal precautions be taken to avoid
application of any voltages higher than maximum-rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate
logic voltage level (for instance, either VSS or VDD) or the programmable pullup resistor
associated with the pin is enabled.
Table 2. Voltage and current operating ratings
Symbol
Description
Min.
Max.
Unit
VDD
Digital supply voltage
–0.3
6.0
V
IDD
Maximum current into VDD
—
120
mA
VIN
ID
VDDA
0.31
Input voltage except true open drain pins
–0.3
VDD +
Input voltage of true open drain pins
–0.3
6
V
Instantaneous maximum current single pin limit (applies to all
port pins)
–25
25
mA
VDD – 0.3
VDD + 0.3
V
Analog supply voltage
V
1. Maximum rating of VDD also applies to VIN.
5 General
5.1 Nonswitching electrical specifications
5.1.1 DC characteristics
This section includes information about power supply requirements and I/O pin
characteristics.
Table 3. DC characteristics
Symbol
C
—
—
Descriptions
Operating voltage
—
Min
Typical1
Max
Unit
2.7
—
5.5
V
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
7
Nonswitching electrical specifications
Table 3. DC characteristics (continued)
Symbol
C
Descriptions
Min
Typical1
Max
Unit
VOH
P
Output All I/O pins, except PTA2 5 V, Iload = –5 mA
high
and PTA3, standard3 V, Iload = –2.5 mA
voltage
drive strength
VDD – 0.8
—
—
V
VDD – 0.8
—
—
V
C
P
High current drive pins,
high-drive strength2
5 V, Iload = –20 mA
VDD – 0.8
—
—
V
3 V, Iload = –10 mA
VDD – 0.8
—
—
V
Output
high
current
Max total IOH for all ports
5V
—
—
–100
mA
3V
—
—
–60
Output
low
voltage
All I/O pins, standarddrive strength
5 V, Iload = 5 mA
—
—
0.8
V
3 V, Iload = 2.5 mA
—
—
0.8
V
5 V, Iload =20 mA
—
—
0.8
V
3 V, Iload = 10 mA
—
—
0.8
V
5V
—
—
100
mA
3V
—
—
60
4.5≤VDD<5.5 V
0.65 × VDD
—
—
2.7≤VDD<4.5 V
0.70 × VDD
—
—
4.5≤VDD<5.5 V
—
—
0.35 ×
VDD
2.7≤VDD<4.5 V
—
—
0.30 ×
VDD
C
IOHT
VOL
D
P
C
P
C
IOLT
VIH
VIL
D
P
P
High current drive pins,
high-drive strength2
Output
low
current
Max total IOL for all ports
Input
high
voltage
All digital inputs
Input low
voltage
All digital inputs
V
V
Vhys
C
Input
hysteresi
s
All digital inputs
—
0.06 × VDD
—
—
mV
|IIn|
P
Input
leakage
current
Per pin (pins in high
impedance input mode)
VIN = VDD or VSS
—
0.1
1
µA
|IINTOT|
C
Total
leakage
combine
d for all
port pins
Pins in high impedance
input mode
VIN = VDD or VSS
—
—
2
µA
RPU
P
Pullup
resistors
All digital inputs, when
enabled (all I/O pins
other than PTA2 and
PTA3)
—
30.0
—
50.0
kΩ
RPU3
P
Pullup
resistors
PTA2 and PTA3 pins
—
30.0
—
60.0
kΩ
IIC
D
DC
Single pin limit
injection
Total MCU limit, includes
current4, sum of all stressed pins
5, 6
VIN < VSS, VIN >
VDD
-2
—
2
mA
-5
—
25
CIn
C
Input capacitance, all pins
—
—
—
7
pF
VRAM
C
RAM retention voltage
—
2.0
—
—
V
1. Typical values are measured at 25 °C. Characterized, not tested.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
8
Freescale Semiconductor, Inc.
Nonswitching electrical specifications
2. Only PTB4, PTB5, PTD0, PTD1, PTE0, PTE1, PTH0 (64-pin and 80-pin packages only), and PTH1 (64-pin and 80-pin
packages only) support high current output.
3. The specified resistor value is the actual value internal to the device. The pullup value may appear higher when measured
externally on the pin.
4. All functional non-supply pins, except for PTA2 and PTA3, are internally clamped to VSS and VDD. PTA2 and PTA3 are true
open drain I/O pins that are internally clamped to VSS.
5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values for positive and negative clamp voltages, then use the larger value.
6. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current
conditions. If the positive injection current (VIn > VDD) is higher than IDD, the injection current may flow out of VDD and could
result in external power supply going out of regulation. Ensure that external VDD load will shunt current higher than
maximum injection current when the MCU is not consuming power, such as when no system clock is present, or clock rate
is very low (which would reduce overall power consumption).
Table 4. LVD and POR specification
Symbol
C
Description
Min
Typ
Max
Unit
1.5
1.75
2.0
V
4.2
4.3
4.4
V
Level 1 falling
(LVWV = 00)
4.3
4.4
4.5
V
Level 2 falling
(LVWV = 01)
4.5
4.5
4.6
V
Level 3 falling
(LVWV = 10)
4.6
4.6
4.7
V
Level 4 falling
(LVWV = 11)
4.7
4.7
4.8
V
POR re-arm
voltage1
VPOR
D
VLVDH
C
VLVW1H
C
VLVW2H
C
VLVW3H
C
VLVW4H
C
VHYSH
C
High range low-voltage
detect/warning hysteresis
—
100
—
mV
VLVDL
C
Falling low-voltage detect
threshold—low range (LVDV
= 0)
2.56
2.61
2.66
V
VLVW1L
C
Level 1 falling
(LVWV = 00)
2.62
2.7
2.78
V
VLVW2L
C
Level 2 falling
(LVWV = 01)
2.72
2.8
2.88
V
VLVW3L
C
Falling lowvoltage
warning
threshold—
low range
Level 3 falling
(LVWV = 10)
2.82
2.9
2.98
V
VLVW4L
C
Level 4 falling
(LVWV = 11)
2.92
3.0
3.08
V
VHYSDL
C
Low range low-voltage detect
hysteresis
—
40
—
mV
VHYSWL
C
Low range low-voltage
warning hysteresis
—
80
—
mV
VBG
P
Buffered bandgap output 3
1.14
1.16
1.18
V
Falling low-voltage detect
threshold—high range (LVDV
= 1)2
Falling lowvoltage
warning
threshold—
high range
1. Maximum is highest voltage that POR is guaranteed.
2. Rising thresholds are falling threshold + hysteresis.
3. voltage Factory trimmed at VDD = 5.0 V, Temp = 25 °C
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
9
Nonswitching electrical specifications
VDD-VOH(V)
IOH(mA)
Figure 1. Typical VDD-VOH Vs. IOH (standard drive strength) (VDD = 5 V)
VDD-VOH(V)
IOH(mA)
Figure 2. Typical VDD-VOH Vs. IOH (standard drive strength) (VDD = 3 V)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
10
Freescale Semiconductor, Inc.
Nonswitching electrical specifications
VDD-VOH(V)
IOH(mA)
Figure 3. Typical VDD-VOH Vs. IOH (high drive strength) (VDD = 5 V)
VDD-VOH(V)
IOH(mA)
Figure 4. Typical VDD-VOH Vs. IOH (high drive strength) (VDD = 3 V)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
11
Nonswitching electrical specifications
VOL(V)
IOL(mA)
Figure 5. Typical VOL Vs. IOL (standard drive strength) (VDD = 5 V)
VOL(V)
IOL(mA)
Figure 6. Typical VOL Vs. IOL (standard drive strength) (VDD = 3 V)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
12
Freescale Semiconductor, Inc.
Nonswitching electrical specifications
VOL(V)
IOL(mA)
Figure 7. Typical VOL Vs. IOL (high drive strength) (VDD = 5 V)
VOL(V)
IOL(mA)
Figure 8. Typical VOL Vs. IOL (high drive strength) (VDD = 3 V)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
13
Nonswitching electrical specifications
5.1.2 Supply current characteristics
This section includes information about power supply current in various operating modes.
Table 5. Supply current characteristics
C
Parameter
Symbol
Core/Bus
Freq
VDD (V)
Typical1
Max2
Unit
Temp
C
Run supply current FEI
mode, all modules clocks
enabled; run from flash
RIDD
48/24 MHz
5
11.1
—
mA
-40 to 105 °C
8
—
mA
-40 to 105 °C
mA
-40 to 105 °C
mA
-40 to 105 °C
C
C
24/24 MHz
12/12 MHz
5
—
C
1/1 MHz
2.4
—
C
48/24 MHz
11
—
C
24/24 MHz
7.9
—
C
12/12 MHz
4.9
—
1/1 MHz
2.3
—
7.8
—
24/24 MHz
5.5
—
C
C
C
Run supply current FEI
mode, all modules clocks
disabled and gated; run
from flash
RIDD
48/24 MHz
3
5
12/12 MHz
3.8
—
C
1/1 MHz
2.3
—
C
48/24 MHz
7.7
—
C
24/24 MHz
5.4
—
C
12/12 MHz
3.7
—
C
1/1 MHz
2.2
—
14.7
—
9.8
14.9
C
P
C
Run supply current FBE
mode, all modules clocks
enabled; run from RAM
RIDD
48/24 MHz
3
5
24/24 MHz
12/12 MHz
6
—
C
1/1 MHz
2.4
—
C
48/24 MHz
14.6
—
P
24/24 MHz
9.6
12.8
C
12/12 MHz
5.9
—
C
1/1 MHz
2.3
—
11.4
—
24/24 MHz
7.7
12.5
C
P
C
Run supply current FBE
mode, all modules clocks
disabled and gated; run
from RAM
RIDD
48/24 MHz
3
5
12/12 MHz
4.7
—
C
1/1 MHz
2.3
—
C
48/24 MHz
11.3
—
P
24/24 MHz
7.6
9.5
C
12/12 MHz
4.6
—
1/1 MHz
2.2
—
3
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
14
Freescale Semiconductor, Inc.
Nonswitching electrical specifications
Table 5. Supply current characteristics (continued)
C
Parameter
Symbol
Core/Bus
Freq
VDD (V)
Typical1
Max2
Unit
Temp
C
Wait mode current FEI
mode, all modules clocks
enabled
WIDD
48/24 MHz
5
8.4
—
mA
-40 to 105 °C
24/24 MHz
6.5
7.2
12/12 MHz
4.3
—
C
1/1 MHz
2.4
—
C
48/24 MHz
8.3
—
µA
-40 to 105 °C
P
C
3
P
24/24 MHz
6.4
7
C
12/12 MHz
4.2
—
C
1/1 MHz
2.3
—
P
P
C
C
Stop mode supply current
no clocks active (except 1
kHz LPO clock)3
SIDD
ADC adder to Stop
—
—
5
2
105
—
3
1.9
95
—
5
86
—
3
82
—
5
12
—
3
12
—
5
130
—
3
125
—
ADLPC = 1
-40 to 105 °C
µA
-40 to 105 °C
µA
-40 to 105 °C
µA
-40 to 105 °C
ADLSMP = 1
ADCO = 1
MODE = 10B
ADICLK = 11B
C
ACMP adder to Stop
—
—
C
C
LVD adder to
Stop4
—
C
1.
2.
3.
4.
—
Data in Typical column was characterized at 5.0 V, 25 °C or is typical recommended value.
The Max current is observed at high temperature of 105 °C.
RTC adder cause <1 µA IDD increase typically, RTC clock source is 1 kHz LPO clock.
LVD is periodically woken up from Stop by 5% duty cycle. The period is equal to or less than 2 ms.
5.1.3 EMC performance
Electromagnetic compatibility (EMC) performance is highly dependent on the
environment in which the MCU resides. Board design and layout, circuit topology
choices, location and characteristics of external components as well as MCU software
operation play a significant role in EMC performance. The system designer must consult
the following Freescale applications notes, available on freescale.com for advice and
guidance specifically targeted at optimizing EMC performance.
• AN2321: Designing for Board Level Electromagnetic Compatibility
• AN1050: Designing for Electromagnetic Compatibility (EMC) with HCMOS
Microcontrollers
• AN1263: Designing for Electromagnetic Compatibility with Single-Chip
Microcontrollers
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
15
Switching specifications
• AN2764: Improving the Transient Immunity Performance of Microcontroller-Based
Applications
• AN1259: System Design and Layout Techniques for Noise Reduction in MCUBased Systems
5.1.3.1
EMC radiated emissions operating behaviors
Table 6. EMC radiated emissions operating behaviors for 80-pin LQFP
package
Symbol
Description
Frequency
band (MHz)
Typ.
Unit
Notes
0.15–50
6
dBμV
1, 2
VRE1
Radiated emissions voltage, band 1
VRE2
Radiated emissions voltage, band 2
50–150
6
dBμV
VRE3
Radiated emissions voltage, band 3
150–500
11
dBμV
VRE4
Radiated emissions voltage, band 4
500–1000
5
dBμV
0.15–1000
N3
—
VRE_IEC
IEC level
2, 4
1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150
kHz to 1 GHz Part 1: General Conditions and Definitions and IEC Standard 61967-2, Integrated Circuits - Measurement of
Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method. Measurements were made while the microcontroller was running basic application code. The reported
emission level is the value of the maximum measured emission, rounded up to the next whole number, from among the
measured orientations in each frequency range.
2. VDD = 5.0 V, TA = 25 °C, fOSC = 8 MHz (crystal), fSYS = 40 MHz, fBUS = 20 MHz
3. IEC/SAE Level Maximums: N≤12 dBµV, M≤18 dBµV, K≤30 dBµV, I ≤36 dBµV, H≤42 dBµV.
4. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method
5.2 Switching specifications
5.2.1 Control timing
Table 7. Control timing
Symbol
Min
Typical1
Max
Unit
System and core clock
fSys
DC
—
48
MHz
P
Bus frequency (tcyc = 1/fBus)
fBus
DC
—
24
MHz
P
Internal low power oscillator frequency
fLPO
0.67
1.0
1.25
KHz
textrst
1.5 ×
—
—
ns
Num
C
1
D
2
3
4
D
Rating
External reset pulse
width2
tcyc
5
D
6
D
D
Reset low drive
IRQ pulse width
trstdrv
34 × tcyc
—
—
ns
Asynchronous
path2
tILIH
100
—
—
ns
Synchronous path3
tIHIL
1.5 × tcyc
—
—
ns
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
16
Freescale Semiconductor, Inc.

Switching specifications
Table 7. Control timing (continued)
Num
C
7
D
Symbol
Min
Typical1
Max
Unit
Asynchronous
path2
tILIH
100
—
—
ns
Synchronous path
tIHIL
1.5 × tcyc
—
—
ns
Port rise and fall time Normal drive strength
(load = 50 pF)4
—
tRise
—
10.2
—
ns
tFall
—
9.5
—
ns
Port rise and fall time high drive strength (load =
50 pF)4
—
tRise
—
5.4
—
ns
tFall
—
4.6
—
ns
Rating
Keyboard interrupt pulse
width
D
8
C
C
C
C
1. Typical values are based on characterization data at VDD = 5.0 V, 25 °C unless otherwise stated.
2. This is the shortest pulse that is guaranteed to be recognized as a RESET pin request.
3. This is the minimum pulse width that is guaranteed to pass through the pin synchronization
circuitry.
Shorter pulses may or


may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized.
4. Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range -40 °C to 105 °C.
textrst
RESET_b pin
Figure 9. Reset timing
tIHIL
KBIPx
IRQ/KBIPx
tILIH
Figure 10. KBIPx timing
5.2.2 FTM module timing
Synchronizer circuits determine the shortest input pulses that can be recognized or the
fastest clock that can be used as the optional external source to the timer counter. These
synchronizers operate from the current bus rate clock.
Table 8. FTM input timing
C
Function
Symbol
Min
Max
Unit
D
Timer clock
frequency
fTimer
fBus
fSys
Hz
D
External clock
frequency
fTCLK
0
fTimer/4
Hz
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
17

Thermal specifications
Table 8. FTM input timing (continued)
C
Function
Symbol
Min
Max
Unit
D
External clock
period
tTCLK
4
—
tTimer1
D
External clock high
time
tclkh
1.5
—
tTimer1
D
External clock low
time
tclkl
1.5
—
tTimer1
D
Input capture pulse
width
tICPW
1.5
—
tTimer1





1. tTimer = 1/fTimer
tTCLK
tclkh
TCLK
tclkl
Figure 11. Timer external clock
tICPW
FTMCHn
FTMCHn
tICPW
Figure 12. Timer input capture pulse
5.3 Thermal specifications
5.3.1 Thermal characteristics
This section provides information about operating temperature range, power dissipation,
and package thermal resistance. Power dissipation on I/O pins is usually small compared
to the power dissipation in on-chip logic and voltage regulator circuits, and it is userdetermined rather than being controlled by the MCU design. To take PI/O into account in
power calculations, determine the difference between actual pin voltage and VSS or VDD
and multiply by the pin current for each I/O pin. Except in cases of unusually high pin
current (heavy loads), the difference between pin voltage and VSS or VDD will be very
small.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
18
Freescale Semiconductor, Inc.
Thermal specifications
Table 9. Thermal attributes
Board type
Symbol
Single-layer (1S)
RθJA
Four-layer (2s2p)
Description
64
LQFP
64 QFP
44
LQFP
80
LQFP
Unit
Notes
Thermal resistance, junction
to ambient (natural
convection)
71
61
75
57
°C/W
1, 2
RθJA
Thermal resistance, junction
to ambient (natural
convection)
53
47
53
44
°C/W
1, 3
Single-layer (1S)
RθJMA
Thermal resistance, junction
to ambient (200 ft./min. air
speed)
59
50
62
47
°C/W
1, 3
Four-layer (2s2p)
RθJMA
Thermal resistance, junction
to ambient (200 ft./min. air
speed)
46
41
47
38
°C/W
1, 3
—
RθJB
Thermal resistance, junction
to board
35
32
34
28
°C/W
4
—
RθJC
Thermal resistance, junction
to case
20
23
20
15
°C/W
5
—
ΨJT
Thermal characterization
parameter, junction to
package top outside center
(natural convection)
5
8
5
3
°C/W
6
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site
(board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board
thermal resistance.
2. Per JEDEC JESD51-2 with the single layer board (JESD51-3) horizontal.
3. Per JEDEC JESD51-6 with the board (JESD51-7) horizontal.
4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured
on the top surface of the board near the package.
5. Thermal resistance between the die and the solder pad on the bottom of the package. Interface resistance is ignored.
6. Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization.
The average chip-junction temperature (TJ) in °C can be obtained from:
TJ = TA + (PD × θJA)
Where:
TA = Ambient temperature, °C
θJA = Package thermal resistance, junction-to-ambient, °C/W
PD = Pint + PI/O
Pint = IDD × VDD, Watts - chip internal power
PI/O = Power dissipation on input and output pins - user determined
For most applications, PI/O << Pint and can be neglected. An approximate relationship
between PD and TJ (if PI/O is neglected) is:
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
19
Peripheral operating requirements and behaviors
PD = K ÷ (TJ + 273 °C)
Solving the equations above for K gives:
K = PD × (TA + 273 °C) + θJA × (PD)2
where K is a constant pertaining to the particular part. K can be determined by measuring
PD (at equilibrium) for an known TA. Using this value of K, the values of PD and TJ can
be obtained by solving the above equations iteratively for any value of TA.
6 Peripheral operating requirements and behaviors
6.1 Core modules
6.1.1 SWD electricals
Table 10. SWD full voltage range electricals
Symbol
J1
Description
Min.
Max.
Unit
Operating voltage
2.7
5.5
V
0
24
MHz
1/J1
—
ns
20
—
ns
SWD_CLK frequency of operation
• Serial wire debug
J2
SWD_CLK cycle period
J3
SWD_CLK clock pulse width
• Serial wire debug
J4
SWD_CLK rise and fall times
—
3
ns
J9
SWD_DIO input data setup time to SWD_CLK rise
10
—
ns
J10
SWD_DIO input data hold time after SWD_CLK rise
3
—
ns
J11
SWD_CLK high to SWD_DIO data valid
—
35
ns
J12
SWD_CLK high to SWD_DIO high-Z
5
—
ns
J2
J3
J3
SWD_CLK (input)
J4
J4
Figure 13. Serial wire clock input timing
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
20
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
SWD_CLK
J9
SWD_DIO
J10
Input data valid
J11
SWD_DIO
Output data valid
J12
SWD_DIO
J11
SWD_DIO
Output data valid
Figure 14. Serial wire data timing
6.2 External oscillator (OSC) and ICS characteristics
Table 11. OSC and ICS specifications (temperature range = -40 to 105 °C ambient)
Num
C
1
C
C
2
D
3
D
4
5
D
D
Symbol
Min
Typical1
Max
Unit
Low range (RANGE = 0)
flo
31.25
32.768
39.0625
kHz
High range (RANGE = 1)
fhi
4
—
24
MHz
Characteristic
Crystal or
resonator
frequency
Load capacitors
Feedback
resistor
See Note2
C1, C2
Low Frequency, Low-Power
Mode3
—
—
—
MΩ
Low Frequency, High-Gain
Mode
—
10
—
MΩ
High Frequency, LowPower Mode
—
1
—
MΩ
High Frequency, High-Gain
Mode
—
1
—
MΩ
—
0
—
kΩ
—
200
—
kΩ
—
0
—
kΩ
Series resistor Low Frequency
Low-Power Mode 3
Series resistor High Frequency
Mode3
RF
RS
High-Gain Mode
Low-Power
RS
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
21
Peripheral operating requirements and behaviors
Table 11. OSC and ICS specifications (temperature range = -40 to 105 °C ambient)
(continued)
Num
C
D
D
D
6
C
C
C
C
Min
Typical1
Max
Unit
4 MHz
—
0
—
kΩ
8 MHz
—
0
—
kΩ
16 MHz
—
0
—
kΩ
—
1000
—
ms
—
800
—
ms
—
3
—
ms
—
1.5
—
ms
Characteristic
Series resistor High
Frequency,
High-Gain Mode
Crystal start-up
time low range
= 32.768 kHz
crystal; High
range = 20 MHz
crystal4,5
Low range, low power
Symbol
tCSTL
Low range, high gain
High range, low power
tCSTH
High range, high gain
7
T
Internal reference start-up time
tIRST
—
20
50
µs
8
P
Internal reference clock (IRC) frequency trim
range
fint_t
31.25
—
39.0625
kHz
9
P
Internal
reference clock
frequency,
factory trimmed,
T = 25 °C, VDD = 5 V
fint_ft
—
37.5
—
kHz
10
P
DCO output
frequency range
FLL reference = fint_t, flo,
or fhi/RDIV
fdco
40
—
50
MHz
11
P
Factory trimmed
internal
oscillator
accuracy
T = 25 °C, VDD = 5 V
Δfint_ft
-0.5
—
0.5
%
12
C
Deviation of IRC
over
temperature
when trimmed
at T = 25 °C,
VDD = 5 V
Over temperature range
from -40 °C to 105°C
Δfint_t
-1
—
0.5
%
Over temperature range
from 0 °C to 105°C
Δfint_t
-0.5
—
0.5
Frequency
accuracy of
DCO output
using factory
trim value
Over temperature range
from -40 °C to 105°C
Δfdco_ft
-1.5
—
1
Over temperature range
from 0 °C to 105°C
Δfdco_ft
-1
—
1
13
C
%
14
C
FLL acquisition time4,6
tAcquire
—
—
2
ms
15
C
Long term jitter of DCO output clock
(averaged over 2 ms interval)7
CJitter
—
0.02
0.2
%fdco
1. Data in Typical column was characterized at 5.0 V, 25 °C or is typical recommended value.
2. See crystal or resonator manufacturer's recommendation.
3. Load capacitors (C1,C2), feedback resistor (RF) and series resistor (RS) are incorporated internally when RANGE = HGO =
0.
4. This parameter is characterized and not tested on each device.
5. Proper PC board layout procedures must be followed to achieve specifications.
6. This specification applies to any time the FLL reference source or reference divider is changed, trim value changed, or
changing from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as
the reference, this specification assumes it is already running.
7. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBus.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage
for a given interval.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
22
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
OSC
XTAL
EXTAL
RS
RF
Crystal or Resonator
C1
C2
Figure 15. Typical crystal or resonator circuit
6.3 NVM specifications
This section provides details about program/erase times and program/erase endurance for
the flash memories.
Table 12. Flash characteristics
C
Characteristic
Symbol
Min1
Typical2
Max3
Unit4
D
Supply voltage for program/erase –40
°C to 105 °C
Vprog/erase
2.7
—
5.5
V
D
Supply voltage for read operation
VRead
2.7
—
5.5
V
D
NVM Bus frequency
fNVMBUS
1
—
24
MHz
D
NVM Operating frequency
fNVMOP
0.8
1
1.05
MHz
D
Erase Verify All Blocks
tVFYALL
—
—
2605
tcyc
D
Erase Verify Flash Block
tRD1BLK
—
—
2579
tcyc
D
Erase Verify Flash Section
tRD1SEC
—
—
485
tcyc
D
Read Once
tRDONCE
—
—
464
tcyc
D
Program Flash (2 word)
tPGM2
0.12
0.13
0.31
ms
D
Program Flash (4 word)
tPGM4
0.21
0.21
0.49
ms
D
Program Once
tPGMONCE
0.20
0.21
0.21
ms
D
Erase All Blocks
tERSALL
95.42
100.18
100.30
ms
D
Erase Flash Block
tERSBLK
95.42
100.18
100.30
ms
D
Erase Flash Sector
tERSPG
19.10
20.05
20.09
ms
D
Unsecure Flash
tUNSECU
95.42
100.19
100.31
ms
D
Verify Backdoor Access Key
tVFYKEY
—
—
482
tcyc
D
Set User Margin Level
tMLOADU
—
—
415
tcyc
C
FLASH Program/erase endurance TL to
TH = -40 °C to 105 °C
nFLPE
10 k
100 k
—
Cycles
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
23
Peripheral operating requirements and behaviors
Table 12. Flash characteristics (continued)
1.
2.
3.
4.
C
Characteristic
Symbol
Min1
Typical2
Max3
Unit4
C
Data retention at an average junction
temperature of TJavg = 85°C after up to
10,000 program/erase cycles
tD_ret
15
100
—
years
Minimum times are based on maximum fNVMOP and maximum fNVMBUS
Typical times are based on typical fNVMOP and maximum fNVMBUS
Maximum times are based on typical fNVMOP and typical fNVMBUS plus aging
tcyc = 1 / fNVMBUS
Program and erase operations do not require any special power sources other than the
normal VDD supply. For more detailed information about program/erase operations, see
the Flash Memory Module section in the reference manual.
6.4 Analog
6.4.1 ADC characteristics
Table 13. 5 V 12-bit ADC operating conditions
Symbol
Min
Typ1
Max
Unit
Comment
VREFL
VSSA
—
VDDA/2
V
—
VREFH
VDDA/2
—
VDDA
Absolute
VDDA
2.7
—
5.5
V
—
Delta to VDD (VDD-VDDA)
Characteri
stic
Reference
potential
Supply
voltage
Conditions
• Low
• High
ΔVDDA
-100
0
+100
mV
—
Input
voltage
VADIN
VREFL
—
VREFH
V
—
Input
capacitance
CADIN
—
4.5
5.5
pF
—
Input
resistance
RADIN
—
3
5
kΩ
—
RAS
—
—
2
kΩ
External to
MCU
—
—
5
—
—
5
—
—
10
—
—
10
0.4
—
8.0
MHz
—
0.4
—
4.0
Analog
source
resistance
•
•
12-bit mode
fADCK > 4 MHz
fADCK < 4 MHz
•
•
10-bit mode
fADCK > 4 MHz
fADCK < 4 MHz
8-bit mode
(all valid fADCK)
ADC
conversion
clock
frequency
High speed (ADLPC=0)
Low power (ADLPC=1)
fADCK
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
24
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
1. Typical values assume VDDA = 5.0 V, Temp = 25°C, fADCK=1.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
Pad
leakage
due to
input
protection
ZAS
R AS
z ADIN
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
ADC SAR
ENGINE
R ADIN
v ADIN
C AS
v AS
R ADIN
INPUT PIN
R ADIN
INPUT PIN
R ADIN
INPUT PIN
C ADIN
Figure 16. ADC input impedance equivalency diagram
Table 14. 12-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA)
Characteristic
Conditions
Supply current
C
Symbol
Min
Typ1
Max
Unit
T
IDDA
—
133
—
µA
T
IDDA
—
218
—
µA
T
IDDA
—
327
—
µA
T
IDDA
—
582
990
µA
T
IDDA
—
0.011
1
µA
ADLPC = 1
ADLSMP = 1
ADCO = 1
Supply current
ADLPC = 1
ADLSMP = 0
ADCO = 1
Supply current
ADLPC = 0
ADLSMP = 1
ADCO = 1
Supply current
ADLPC = 0
ADLSMP = 0
ADCO = 1
Supply current
Stop, reset, module
off
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
25
Peripheral operating requirements and behaviors
Table 14. 12-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Characteristic
Conditions
C
Symbol
Min
Typ1
Max
Unit
ADC asynchronous
clock source
High speed (ADLPC
= 0)
P
fADACK
2
3.3
5
MHz
1.25
2
3.3
—
20
—
—
40
—
—
3.5
—
—
23.5
—
—
±5.0
—
Low power (ADLPC
= 1)
Conversion time
(including sample
time)
Short sample
(ADLSMP = 0)
Sample time
Short sample
(ADLSMP = 0)
T
tADC
Long sample
(ADLSMP = 1)
T
tADS
Long sample
(ADLSMP = 1)
Total unadjusted
Error2
Differential NonLiniarity
12-bit mode
C
ETUE
10-bit mode
C
—
±1.5
—
8-bit mode
C
—
±0.8
—
12-bit mode
C
—
±1.5
—
10-bit mode
C
—
±0.4
—
8-bit mode
C
—
±0.15
—
—
±1.5
—
DNL
Integral Non-Linearity 12-bit mode
C
10-bit mode
C
—
±0.4
—
8-bit mode
C
—
±0.15
—
12-bit mode
C
—
±1.0
—
10-bit mode
C
—
±0.2
—
8-bit mode
C
—
±0.35
—
12-bit mode
C
—
±2.5
—
10-bit mode
C
—
±0.3
—
8-bit mode
C
—
±0.25
—
≤12 bit modes
D
EQ
—
—
±0.5
all modes
D
EIL
-40 °C–25 °C
D
m
Zero-scale
Full-scale
error4
error5
Quantization error
Input leakage
error6
Temp sensor slope
INL
EZS
EFS
25 °C–125 °C
Temp sensor voltage 25 °C
D
VTEMP25
IIn * RAS
ADCK
cycles
ADCK
cycles
LSB3
LSB3
LSB3
LSB3
LSB3
LSB3
mV
—
3.266
—
—
3.638
—
—
1.396
—
mV/°C
V
1. Typical values assume VDDA = 5.0 V, Temp = 25 °C, fADCK=1.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2. Includes quantization
3. 1 LSB = (VREFH - VREFL)/2N
4. VADIN = VSSA
5. VADIN = VDDA
6. IIn = leakage current (refer to DC characteristics)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
26
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
6.4.2 Analog comparator (ACMP) electricals
Table 15. Comparator electrical specifications
C
Characteristic
Symbol
Min
Typical
Max
Unit
D
Supply voltage
VDDA
2.7
—
5.5
V
T
Supply current (Operation mode)
IDDA
—
10
20
µA
D
Analog input voltage
VAIN
VSS - 0.3
—
VDDA
V
P
Analog input offset voltage
VAIO
—
—
40
mV
C
Analog comparator hysteresis (HYST=0)
VH
—
15
20
mV
C
Analog comparator hysteresis (HYST=1)
VH
—
20
30
mV
T
Supply current (Off mode)
IDDAOFF
—
60
—
nA
C
Propagation Delay
tD
—
0.4
1
µs
6.5 Communication interfaces
6.5.1 SPI switching specifications
The serial peripheral interface (SPI) provides a synchronous serial bus with master and
slave operations. Many of the transfer attributes are programmable. The following tables
provide timing characteristics for classic SPI timing modes. See the SPI chapter of the
chip's reference manual for information about the modified transfer formats used for
communicating with slower peripheral devices. All timing is shown with respect to 20%
VDD and 80% VDD, unless noted, and 25 pF load on all SPI pins. All timing assumes slew
rate control is disabled and high-drive strength is enabled for SPI output pins.
Table 16. SPI master mode timing
Nu
m.
Symbol
Description
Min.
Max.
Unit
Comment
1
fop
fBus/2048
fBus/2
Hz
fBus is the bus
clock
2
tSPSCK
2 x tBus
2048 x tBus
ns
tBus = 1/fBus
3
tLead
Enable lead time
1/2
—
tSPSCK
—
4
tLag
Enable lag time
1/2
—
tSPSCK
—
5
tWSPSCK
6
tSU
Data setup time (inputs)
tBus – 30
1024 x tBus
ns
—
8
—
ns
—
7
tHI
Data hold time (inputs)
8
—
ns
—
8
tv
Data valid (after SPSCK edge)
—
25
ns
—
9
tHO
Data hold time (outputs)
20
—
ns
—
10
tRI
Rise time input
—
tBus – 25
ns
—
Frequency of operation
SPSCK period
Clock (SPSCK) high or low time
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
27
Peripheral operating requirements and behaviors
Table 16. SPI master mode timing (continued)
Nu
m.
11
Symbol
Description
tFI
Fall time input
tRO
Rise time output
tFO
Fall time output
Min.
Max.
Unit
Comment
—
25
ns
—
SS 1
(OUTPUT)
3
2
SPSCK
(CPOL=0)
(OUTPUT)
10
11
10
11
4
5
5
SPSCK
(CPOL=1)
(OUTPUT)
6
MISO
(INPUT)
7
MSB IN 2
BIT 6 . . . 1
LSB IN
8
MOSI
(OUTPUT)
MSB OUT 2
9
BIT 6 . . . 1
LSB OUT
1. If configured as an output.
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 17. SPI master mode timing (CPHA=0)
SS 1
(OUTPUT)
2
3
10
11
10
11
4
SPSCK
(CPOL=0)
(OUTPUT)
5
SPSCK
(CPOL=1)
(OUTPUT)
5
6
MISO
(INPUT)
7
MSB IN
BIT 6 . . . 1
2
9
8
MOSI
(OUTPUT)
LSB IN
PORT DATA MASTER MSB OUT
2
BIT 6 . . . 1
MASTER LSB OUT
PORT DATA
1.If configured as output
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Figure 18. SPI master mode timing (CPHA=1)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
28
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 17. SPI slave mode timing
Nu
m.
Symbol
Description
1
fop
2
tSPSCK
3
tLead
Enable lead time
4
tLag
Enable lag time
5
tWSPSCK
6
tSU
7
Min.
Max.
Unit
Comment
0
fBus/4
Hz
fBus is the bus clock as
defined in Control timing.
4 x tBus
—
ns
tBus = 1/fBus
1
—
tBus
—
Frequency of operation
SPSCK period
1
—
tBus
—
tBus - 30
—
ns
—
Data setup time (inputs)
15
—
ns
—
tHI
Data hold time (inputs)
25
—
ns
—
8
ta
Slave access time
—
tBus
ns
Time to data active from
high-impedance state
9
tdis
Slave MISO disable time
—
tBus
ns
Hold time to highimpedance state
10
tv
Data valid (after SPSCK edge)
—
25
ns
—
11
tHO
Data hold time (outputs)
0
—
ns
—
12
tRI
Rise time input
—
tBus - 25
ns
—
tFI
Fall time input
tRO
Rise time output
—
25
ns
—
tFO
Fall time output
13
Clock (SPSCK) high or low time
SS
(INPUT)
2
12
13
12
13
4
SPSCK
(CPOL=0)
(INPUT)
5
3
SPSCK
(CPOL=1)
(INPUT)
5
9
8
MISO
(OUTPUT)
see
note
SLAVE MSB
6
MOSI
(INPUT)
10
11
11
BIT 6 . . . 1
SLAVE LSB OUT
SEE
NOTE
7
MSB IN
BIT 6 . . . 1
LSB IN
NOTE: Not defined
Figure 19. SPI slave mode timing (CPHA = 0)
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
29
Dimensions
SS
(INPUT)
4
2
3
SPSCK
(CPOL=0)
(INPUT)
5
SPSCK
(CPOL=1)
(INPUT)
5
SLAVE
8
MSB OUT
6
MOSI
(INPUT)
13
12
13
11
10
see
note
MISO
(OUTPUT)
12
9
BIT 6 . . . 1
SLAVE LSB OUT
BIT 6 . . . 1
LSB IN
7
MSB IN
NOTE: Not defined
Figure 20. SPI slave mode timing (CPHA=1)
6.5.2 MSCAN
Table 18. MSCAN wake-up pulse characteristics
Parameter
Symbol
Min
Typ
Max
Unit
MSCAN wakeup dominant pulse filtered
tWUP
-
-
1.5
µs
MSCAN wakeup dominant pulse pass
tWUP
5
-
-
µs
7 Dimensions
7.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to freescale.com and perform a keyword search for the
drawing’s document number:
If you want the drawing for this package
Then use this document number
44-pin LQFP
98ASS23225W
64-pin QFP
98ASB42844B
64-pin LQFP
98ASS23234W
80-pin LQFP
98ASS23237W
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
30
Freescale Semiconductor, Inc.
Pinout
8 Pinout
8.1 Signal multiplexing and pin assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
NOTE
VSS and VSSA are internally connected.
VREFH and VDDA are internally connected in 64-pin
packages.
PTB4, PTB5, PTD0, PTD1, PTE0, PTE1, PTH0, and PTH1 are
high-current drive pins when operated as output.
PTA2 and PTA3 are true open-drain pins when operated as
output.
80
64
44
LQFP LQFP LQFP
/QFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
1
1
1
PTD1
DISABLED
PTD1
KBI0_P25
FTM2_CH3
SPI1_MOSI
2
2
2
PTD0
DISABLED
PTD0
KBI0_P24
FTM2_CH2
SPI1_SCK
3
3
—
PTH7
DISABLED
PTH7
KBI1_P31
PWT_IN1
4
4
—
PTH6
DISABLED
PTH6
KBI1_P30
5
—
—
PTH5
DISABLED
PTH5
KBI1_P29
6
5
3
PTE7
DISABLED
PTE7
KBI1_P7
TCLK2
FTM1_CH1
CAN0_TX
7
6
4
PTH2
DISABLED
PTH2
KBI1_P26
BUSOUT
FTM1_CH0
CAN0_RX
8
7
5
VDD
VDD
9
8
6
VDDA
VDDA
10
—
—
VREFH
VREFH
VREFH
11
9
7
VREFL
VREFL
VREFL
12
10
8
VSS/
VSSA
VSS/
VSSA
13
11
9
PTB7
EXTAL
PTB7
KBI0_P15
I2C0_SCL
EXTAL
14
12
10
PTB6
XTAL
PTB6
KBI0_P14
I2C0_SDA
XTAL
15
13
11
PTI4
DISABLED
PTI4
IRQ
16
—
—
PTI1
DISABLED
PTI1
IRQ
UART2_TX
17
—
—
PTI0
DISABLED
PTI0
IRQ
UART2_RX
18
14
—
PTH1
DISABLED
PTH1
ALT7
VDD
VREFH
VSSA
KBI1_P25
VDDA
VSS
FTM2_CH1
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
31
Pinout
80
64
44
LQFP LQFP LQFP
/QFP
Pin Name
Default
ALT0
ALT1
ALT2
FTM2_CH0
ALT3
ALT4
19
15
—
PTH0
DISABLED
PTH0
KBI1_P24
20
16
—
PTE6
DISABLED
PTE6
KBI1_P6
21
17
—
PTE5
DISABLED
PTE5
KBI1_P5
22
18
12
PTB5
DISABLED
PTB5
KBI0_P13
FTM2_CH5
SPI0_PCS
ACMP1_OUT
23
19
13
PTB4
NMI_b
PTB4
KBI0_P12
FTM2_CH4
SPI0_MISO
ACMP1_IN2
24
20
14
PTC3
ADC0_SE11
PTC3
KBI0_P19
FTM2_CH3
ADC0_SE11
25
21
15
PTC2
ADC0_SE10
PTC2
KBI0_P18
FTM2_CH2
ADC0_SE10
26
22
16
PTD7
DISABLED
PTD7
KBI0_P31
UART2_TX
27
23
17
PTD6
DISABLED
PTD6
KBI0_P30
UART2_RX
28
24
18
PTD5
DISABLED
PTD5
KBI0_P29
PWT_IN0
29
—
—
PTI6
DISABLED
PTI6
IRQ
ALT5
ALT6
ALT7
NMI_b
30
—
—
PTI5
DISABLED
PTI5
IRQ
31
25
19
PTC1
ADC0_SE9
PTC1
KBI0_P17
FTM2_CH1
ADC0_SE9
32
26
20
PTC0
ADC0_SE8
PTC0
KBI0_P16
FTM2_CH0
ADC0_SE8
33
—
—
PTH4
DISABLED
PTH4
KBI1_P28
I2C1_SCL
34
—
—
PTH3
DISABLED
PTH3
KBI1_P27
I2C1_SDA
35
27
—
PTF7
ADC0_SE15
PTF7
KBI1_P15
ADC0_SE15
36
28
—
PTF6
ADC0_SE14
PTF6
KBI1_P14
ADC0_SE14
37
29
—
PTF5
ADC0_SE13
PTF5
KBI1_P13
ADC0_SE13
38
30
—
PTF4
ADC0_SE12
PTF4
KBI1_P12
39
31
21
PTB3
ADC0_SE7
PTB3
KBI0_P11
SPI0_MOSI
FTM0_CH1
ADC0_SE7
40
32
22
PTB2
ADC0_SE6
PTB2
KBI0_P10
SPI0_SCK
FTM0_CH0
ADC0_SE6
41
33
23
PTB1
ADC0_SE5
PTB1
KBI0_P9
UART0_TX
42
34
24
PTB0
ADC0_SE4
PTB0
KBI0_P8
UART0_RX
43
35
—
PTF3
DISABLED
PTF3
KBI1_P11
UART1_TX
44
36
—
PTF2
DISABLED
PTF2
KBI1_P10
UART1_RX
45
37
25
PTA7
ADC0_SE3
PTA7
KBI0_P7
46
38
26
PTA6
ADC0_SE2
PTA6
KBI0_P6
47
39
—
PTE4
DISABLED
PTE4
KBI1_P4
48
40
27
VSS
VSS
VSS
49
41
28
VDD
VDD
VDD
50
—
—
PTG7
DISABLED
PTG7
KBI1_P23
FTM2_CH5
SPI1_PCS
51
—
—
PTG6
DISABLED
PTG6
KBI1_P22
FTM2_CH4
SPI1_MISO
52
—
—
PTG5
DISABLED
PTG5
KBI1_P21
FTM2_CH3
SPI1_MOSI
53
—
—
PTG4
DISABLED
PTG4
KBI1_P20
FTM2_CH2
SPI1_SCK
54
42
—
PTF1
DISABLED
PTF1
KBI1_P9
FTM2_CH1
55
43
—
PTF0
DISABLED
PTF0
KBI1_P8
FTM2_CH0
56
44
29
PTD4
DISABLED
PTD4
KBI0_P28
57
45
30
PTD3
DISABLED
PTD3
KBI0_P27
SPI1_PCS
58
46
31
PTD2
DISABLED
PTD2
KBI0_P26
SPI1_MISO
ADC0_SE12
ADC0_SE5
PWT_IN1
ADC0_SE4
FTM2_FLT2
ACMP1_IN1
ADC0_SE3
FTM2_FLT1
ACMP1_IN0
ADC0_SE2
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
32
Freescale Semiconductor, Inc.
Pinout
80
64
44
LQFP LQFP LQFP
/QFP
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
59
47
32
PTA3
DISABLED
PTA3
KBI0_P3
UART0_TX
I2C0_SCL
60
48
33
PTA2
DISABLED
PTA2
KBI0_P2
UART0_RX
I2C0_SDA
61
49
34
PTA1
ADC0_SE1
PTA1
KBI0_P1
FTM0_CH1
I2C0_
4WSDAOUT
ACMP0_IN1
ADC0_SE1
62
50
35
PTA0
ADC0_SE0
PTA0
KBI0_P0
FTM0_CH0
I2C0_
4WSCLOUT
ACMP0_IN0
ADC0_SE0
63
51
36
PTC7
DISABLED
PTC7
KBI0_P23
UART1_TX
CAN0_TX
64
52
37
PTC6
DISABLED
PTC6
KBI0_P22
UART1_RX
CAN0_RX
65
—
—
PTI3
DISABLED
PTI3
IRQ
66
—
—
PTI2
DISABLED
PTI2
IRQ
67
53
—
PTE3
DISABLED
PTE3
KBI1_P3
SPI0_PCS
68
54
38
PTE2
DISABLED
PTE2
KBI1_P2
SPI0_MISO
69
—
—
VSS
VSS
VSS
70
—
—
VDD
VDD
VDD
71
55
—
PTG3
DISABLED
PTG3
KBI1_P19
72
56
—
PTG2
DISABLED
PTG2
KBI1_P18
73
57
—
PTG1
DISABLED
PTG1
KBI1_P17
74
58
—
PTG0
DISABLED
PTG0
KBI1_P16
75
59
39
PTE1
DISABLED
PTE1
KBI1_P1
SPI0_MOSI
76
60
40
PTE0
DISABLED
PTE0
KBI1_P0
SPI0_SCK
77
61
41
PTC5
DISABLED
PTC5
KBI0_P21
78
62
42
PTC4
SWD_CLK
PTC4
KBI0_P20
RTC_CLKOUT
FTM1_CH0
ACMP0_IN2
79
63
43
PTA5
RESET_b
PTA5
KBI0_P5
IRQ
TCLK0
RESET_b
80
64
44
PTA4
SWD_DIO
PTA4
KBI0_P4
ACMP0_OUT
SWD_DIO
ALT7
PWT_IN0
I2C1_SCL
TCLK1
I2C1_SDA
FTM1_CH1
RTC_CLKOUT
SWD_CLK
8.2 Device pin assignment
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
33
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTG0
PTG1
PTG2
PTG3
VDD
VSS
PTE2
PTE3
PTI2
PTI3
PTC6
PTC7
PTA0
PTA1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
Pinout
VREFL
11
50
PTG7
VSS/VSSA
12
49
VDD
PTB7
13
48
VSS
PTB6
14
47
PTE4
PTI4
15
46
PTA6
PTI1
16
45
PTA7
PTI0
17
44
PTF2
PTH1
18
43
PTF3
PTH0
19
42
PTB0
PTE6
20
41
PTB1
40
PTG6
PTB2
51
39
10
PTB3
VREFH
38
PTG5
PTF4
52
37
9
PTF5
VDDA
36
PTG4
PTF6
53
35
8
PTF7
VDD
34
PTF1
PTH3
54
33
7
PTH4
PTH2
PTC0
PTF0
32
55
31
6
PTC1
PTE7
30
PTD4
PTI5
56
29
5
PTI6
PTH5
28
PTD3
PTD5
57
27
4
PTD6
PTH6
26
PTD2
PTD7
58
25
3
PTC2
PTH7
24
PTA3
PTC3
59
23
2
PTB4
PTD0
22
PTA2
PTB5
60
21
1
PTE5
PTD1
Figure 21. 80-pin LQFP package
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
34
Freescale Semiconductor, Inc.
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTG0
PTG1
PTG2
PTG3
PTE2
PTE3
PTC6
PTC7
PTA0
PTA1
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
Pinout
VDD
VREFL
9
40
VSS
VSS/VSSA
10
39
PTE4
PTB7
11
38
PTA6
PTB6
12
37
PTA7
PTI4
13
36
PTF2
PTH1
14
35
PTF3
PTH0
15
34
PTB0
PTE6
16
33
PTB1
PTE5
32
41
PTB2
8
31
VDDA/VREFH
PTB3
PTF1
30
42
PTF4
7
29
VDD
PTF5
PTF0
28
43
PTF6
6
27
PTH2
PTF7
PTD4
26
44
PTC0
5
25
PTE7
PTC1
PTD3
24
45
PTD5
4
23
PTH6
PTD6
PTD2
22
46
PTD7
3
21
PTH7
PTC2
PTA3
20
47
PTC3
2
19
PTD0
PTB4
PTA2
18
48
PTB5
1
17
PTD1
Figure 22. 64-pin QFP/LQFP packages
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
35
PTA4
PTA5
PTC4
PTC5
PTE0
PTE1
PTE2
PTC6
PTC7
PTA0
PTA1
44
43
42
41
40
39
38
37
36
35
34
Revision history
6
28
VDD
VREFL
7
27
VSS
VSS/VSSA
8
26
PTA6
PTB7
9
25
PTA7
PTB6
10
23
PTB1
PTI4
11
24
PTB0
PTB5
22
VDDA/VREFH
PTB2
PTD4
21
29
PTB3
5
20
VDD
PTC0
PTD3
19
30
PTC1
4
18
PTH2
PTD5
PTD2
17
31
PTD6
3
16
PTE7
PTD7
PTA3
15
32
PTC2
2
14
PTD0
PTC3
PTA2
13
33
PTB4
1
12
PTD1
Figure 23. 44-pin LQFP package
9 Revision history
The following table provides a revision history for this document.
Table 19. Revision history
Rev. No.
Date
2
3/2014
Substantial Changes
Initial public release.
Table continues on the next page...
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
36
Freescale Semiconductor, Inc.
Revision history
Table 19. Revision history (continued)
Rev. No.
Date
3
5/2014
Substantial Changes
• Updated the Max. of SIDD.
• Updated footnote to the VOH.
• Corrected Unit in the FTM input timing table.
KE06 Sub-Family Data Sheet, Rev3, 5/2014.
Freescale Semiconductor, Inc.
37
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Information in this document is provided solely to enable system and
software implementers to use Freescale products. There are no express
or implied copyright licenses granted hereunder to design or fabricate
any integrated circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to
any products herein.
Freescale makes no warranty, representation, or guarantee regarding
the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale data sheets
and/or specifications can and do vary in different applications, and
actual performance may vary over time. All operating parameters,
including “typicals,” must be validated for each customer application by
customer's technical experts. Freescale does not convey any license
under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found
at the following address: freescale.com/SalesTermsandConditions.
Freescale, the Freescale logo, and Kinetis are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or
service names are the property of their respective owners. ARM and
Cortex-M0+ are the registered trademarks of ARM Limited.
©2013-2014 Freescale Semiconductor, Inc.
Document Number MKE06P80M48SF0
Revision 3, 5/2014