8 6 7 5 ALUMINUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMA/SMP ADAPTABLE, PRESS-IN 3 4 • CONFIGURATION FOR INTERFACING TO SSMA PANEL JACK FEEEDTHROUGH D 2 SRIFT532 DOCUMENT REVISIONS REV CHANGE NO. DATE - INIT RLSE 1/16/2015 RELEASE APPROVAl J.PETRI A DCN001589 8/13/2015 J.PETRI B DCN001605 9/8/2015 Jim Petri 2015.09.11 13:49:03 -04'00' • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL OUTER KNURL FOR MECHANICAL STABILITY • USE IN CONJUNCTION WITH SRIC118-2 CABLE ADAPTOR AND SRIC119-1 JAM NUT B 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10^-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE .223 UNPLATED (WELD FLANGE) .319 MAX OVER KNURL .130 2. NOMINAL IMPEDANCE: 50 OHMS .050 3. INTERFACES IN ACCORDANCE WITH MIL-STD-348, SERIES SMA AND SERIES SMP, PIN CONTACTS. 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15 DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (MATCHED SEAL) SHELL (WELD FLANGE): ALUMINUM ALLOY 4047 IN ACCORDANCE WITH AWS A5.8 C .250-36 UNS-2B .003 M A B 5. FINISH: PIN AND SHELLS (EXCEPT WELD FLANGE): NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488, TYPE III, CODE A, .000050/.000100 THICK C .164 .300 6. ORDERING INSTRUCTIONS: SPECIFY PART NUMBER SRIFT532 - FD FD=SMP FULL DETENT LD=SMP LIMITED DETENT .015±.001 (PIN BOTH ENDS) SB= SMP SMOOTH BORE DIELECTRIC .050 AS REQD .3150±.0005 B .152 B .218±.002 .003 MAX BRK .230±.002 .303±.001 NO PLATING .040 MIN ALL AROUND .100 B A A SUGGESTED HOLE DETAIL (NOT TO SCALE) VIEWS FOR REFERENCE ONLY DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION a division of WINCHESTER TITLE FEEDTHROUGH, SMA TO SMP, AC LBW (KNURLED) SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 (321) 254-4067 www.srihermetics.com SCALE 8:1 2 CAGE CODE SRIFT532 3PJY7 SHEET 1 REV B 1 OF 2 8 7 6 5 3 4 2 SRIFT532 DOCUMENT D D JAM NUT (SRIC119-1) CABLE ADAPTOR (SRIC118-2) RECOMMENDED TOOLING C FEEDTHROUGH (SRIFT532-TAB) TOOL INSTALLING COMPONENT TORQUE SRIT103-1 CABLE ADAPTOR 13 ± 1 LB-IN SRIT107-1 JAM NUT 19 ± 1LB-IN C B B A A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 63 RMS SURFACE FINISH THIRD ANGLE PROJECTION a division of WINCHESTER TITLE FEEDTHROUGH, SMA TO SMP, AC LBW (KNURLED) SIZE DOCUMENT A DO NOT SCALE DRAWING FORM 300067 REV A 7 6 5 4 3 (321) 254-4067 www.srihermetics.com SCALE 2:1 2 CAGE CODE SRIFT532 3PJY7 SHEET 1 REV B 2 OF 2