SITOP power supply: The standard for reliability, compactness, and functionality Reliably supplies 24 V DC www.usa.siemens.com/sitop Always available, always safe: SITOP A reliable, constant supply of power is indispensable to the efficient operation of any plant – 365 days a year. This is precisely what SITOP represents, our perfectly matched, complete range of products that sets standards in reliability, compactness and functionality. SITOP proves its value a million times a day in practical use – protecting against plant shutdown and production downtimes. 2 Reliable, functional … The product lines of our family of switched mode power supply units cover just about all requirements in automation engineering: • Innovative: LOGO!Power: the flat power supply unit for low power ratings • New: SITOP compact, the slim power supply for low power ratings • SITOP smart for all standard applications, now also as 3-phase version • SITOP modular for the highest demands • SITOP in SIMATIC design In addition, SITOP versions meet special requirements regarding design, ambient conditions, and output voltage. Regardless of which switched-mode power supply you are using: You will profit from the highest quality, reliability, and functionality. ... extremely compact ... Broad functionality and high performance do not have to take up a lot of space. This is made impressively clear by the innovative 24 V DC basic units 20 A and 40 A from SITOP modular, which are among the most compact in their performance class. The slimmest switched-mode power supply in the new SITOP compact product range, designed for low rated outputs up to 30 W, requires only 22.5 mm of space on the DIN rail. … and highly efficient The compact line is optimally suited for distributed applications – not only because of its small footprint, but also due to its minimal heat generation in the control box. Power loss is low over the entire load range, even in during no-load operation. The new 3-phase SITOP smart 20 A is also characterized by its high efficiency, and like the new SITOP modular 20 and 40 A, its degree of efficiency exceeds 90 %. Tailored safety The quality of the 24 V DC power supply unit alone does not guarantee a fault-free power supply. Power failures, extreme supply voltage fluctuations, or a defective load can stop plant operation and cause considerable costs. In answer to this, SITOP offers a unique range of add-on modules to protect against faults on the primary and secondary side – all the way to complete all-round protection. Three SITOP solutions alone for 24 V DC backup are available for protection against power failures, including the completely maintenance-free UPS with innovative capacitor technology. For all networks worldwide Thanks to its high level of reliability, SITOP has long become established worldwide – and it can even handle critical network conditions. The wide input voltage range allows a connection to almost any electrical power system worldwide. SITOP units are CE and UL/ cUL-certified by default. Many devices have approvals for special applications such as in shipbuilding (GL) or in hazardous areas (ATEX). Quick delivery – for highest availability SITOP power supplies increase the availability of your plant, and the units themselves are highly available – because they are all in stock. 3 LOGO! Power lite The flat power supply unit for distribution boards Cost-effective power supply for basic applications The new miniature power supply units now offer even greater performance in the smallest space. The efficiency has been improved throughout the entire load range and the power loss in no-load operation has been reduced 50%. The wide input voltage range now also allows operation on DC voltage, the switch-on response has been optimized for capacitive loads, and the operating temperature range has been extended to +70 °C. The power supplies with logic module design can now be used extremely flexibly in a number of applications – for example, in distribution boards thanks to their flat, stepped profile. The new range of power supplies is designed for standard requirements in industrial environments and offers all important functions at a favorable price, of course without compromising quality and reliability. The wide input voltage range with manual switchover supports connection to a wide range of 1-phase supply systems. Thanks to the narrow width, the devices require little space on the DIN rail, and the good efficiency results in low thermal losses in the control cabinet. Short-circuit and overload protection as well as UL approval for export ensure problem-free use. Essential product features Essential product features • 2 performance classes, each with 5 V DC, 12 V DC, and 15 V DC • 24 V/2.5 A, 5 A and 10 A for industrial applications with standard requirements • 3 performance classes with 24 V DC • 1-phase wide input voltage range with manual switchover • Flat type of construction in LOGO! design, only 55 mm deep • High degree of efficiency • Constant current for connecting loads with high inrush current • Parallel connection possible • Green LED for “24 V DC OK“ • Adjustable output voltage • Temperature range of 0 °C to 60 °C (above 45 °C with derating) • Green LED for “Output voltage o. k.“ • Cooling through natural convection • Temperature range from -20 °C to +70°C • Short-circuit and overload protection • Comprehensive certification, e. g. ATEX, FM class 1, div. 2, GL, ABS and UL class 2 4 • Narrow mounting width • Wide input voltage range from 85 V to 264 V AC or 110 V to 300 V DC respectively compact smart The slim power supply unit for control boxes The powerful standard power supply Thanks to the extremely space-saving slim design, the new power supply series for the lower performance range is especially suited to distributed applications in control boxes or in small control cabinets. The switched-mode power supplies are characterized by their low power loss over the entire load range. Power loss is extremely low even during no-load operation, which is why they are ideal, for example, for supplying machinery and equipment that are often in stand-by mode. SITOP Smart is the ideal choice for all 24 V DC applications. In addition to the proven 1-phase power supplies, 3-phase power supplies are now available as well in 10A, 20A and 40A. Whether 1-phase or 3-phase: they are compact, powerful, and low priced. They offer an outstanding overload response despite their compact dimensions. The SITOP PSU100C switched-mode power supplies have a wide input voltage range for AC and DC networks, with plug-in terminals allowing a simple electrical connection. Thanks to the Extra Power feature with 1.5 times the rated current for 5 seconds, even high inrush loads can be switched on without any problem. With a continuous rated power of 120 percent, the slim power supply units are among the most reliable of their kind. Numerous certifications facilitate the universal and global use and permit their use in hazardous areas. Essential product features Essential product features • 24V DC/0.6 A, 1.3 A, 2.5A, and 4 A and 12V DC/2.0 A and 6.5A • 24 V DC/2.5, 5, 10 and 20 A for standard single phase applications • Small mounting surface thanks to its slim design • 12V DC/ 7A and 14A units for standard single phase applications • Wide input voltage range from 85 V to 264 V AC or 100 VDC to 300 V DC • High efficiency over the entire load range. Up to 28 % energy savings compared to similar units • Low energy consumption during no-load or standby operation. Up to 53 % energy savings possible • Adjustable output voltage • 24 V DC/ 10A, 20A and 40A for standard 3-phase applications • 24 V DC/10 A, wall-mounted for high shock and vibration requirements • Extra Power function for brief operational overload • Green LED for “Output voltage o. k.” • Permanent overload capability up to 45 °C ambient temperature • Plug-in terminals • No lateral installation clearances required • Temperature range from -20 °C to +70 °C • Output voltage adjustable up to 28 V DC for 24V DC units or 15.5 V DC for 12 V DC units • Comprehensive certification, e. g. ATEX • Comprehensive certification, GL, ATEX and class 1, div. 2 • Expandable with DC UPS, redundancy module, and the electronic diagnostic module 5 modular Technology power supply for demanding solutions SITOP modular meets the highest requirements for functionality, e. g. for use in complex plants and machines. The wide input voltage range enables connection to any system in the world and guarantees a high level of safety even in the event of large voltage fluctuations. The power boost function briefly supplies up to three times the rated current. In the case of an overload, you can choose between constant current with automatic restart, or user directed restart. The innovated 1-phase SITOP PSU100M 20 A and 3-ph SITOP PSU300M 20 and 40 A power supply units now offer even more. With their narrow profile design, they are some of the most compact modules in their power class. Improvements include the integrated signaling contact for “24 V DC o.k.“, an expanded input voltage range, high efficiency level of 93 %, and a supply of 1.5 times the rated current for up to 5 seconds. Essential product features • For demanding applications of 5 to 40 A • 48V DC/10A and 20A enables small cable cross-sections • Compact metal housing • No installation clearances required at the sides • Wide input voltage range • Extra Power for brief operational overload • Power Boost for triggering protective equipment • Selectable short-circuit characteristics • Soft characteristic curve selectable for parallel switching • High efficiency • Operating status indicated by 3 LEDs • Can be combined with SITOP power security components and DC UPS 6 SITOP in special design, for special uses Equipped for special tasks and conditions Restricted installation conditions, harsh environmental conditions, or special input or output voltages – whatever the special conditions, these standard power supplies meet even exceptional requirements. • SITOP flat design – in flat metal housing • SITOP 3.7 A Class UL class 2 with power limiting to 100 W • DC/DC converter in narrow design for 12 V from the 24 V DC • SITOP dual – with 2 outputs, e. g. for electronic loads that are supplied with ±15 V DC • SITOP flexi – flexibly adjustable output 3 to 52 V DC for extensive functions such as adjustable output current 2 to 10 A, current monitor and sensor cable • PSU100D direct mount – for direct wall mounting in various installation positions • PSU300B – three phase power supplies optimized for battery charging • PSU300E – 24V/5A, three phase power supply for lower wattage applications SITOP power supplies in the SIMATIC design The optimal power supply for SIMATIC S7 and more The design and functionality of the original power supplies of the SIMATIC merge optimally into the PLC network. As well as the following SIMATIC systems, they also supply other loads reliably with 24 V DC: • SIMATIC S7-1200 – the new micro PLC is supplied by the compact PM1207 power module. The automatic range changeover function ensures that the unit can be easily connected to 1-phase 120 V AC and 230 V line supplies. • SIMATIC S7-200 – the flat power supply is also in demand for shallow installation depths. • SIMATIC S7-300 – The innovated system and load power supplies require up to 33 % less space on the S7 mounting rail than the previous PS307. The range changeover to 1-phase 120/230 V AC line supplies is now realized automatically, therefore preventing incorrect operator settings. The connecting comb to the CPU is included in the scope of supply; an optional adapter allows the unit to be snapped onto DIN mounting rails. • SIMATIC S7-1500 – the new PLC is supplied by two versions of the PM1507. The power modules have automatic range detection for easy connection to 120 and 230 VAC power networks. They also feature extra power of 150% of the rated output current for 5s/min for brief overloads. 7 7 Power security modules Our extensive range of power security modules offers reliable protection against the most diverse hazard sources. Buffer module against brief power failure Power failures usually only last a few 100 ms – voltage drops that the buffer module, in combination with the SITOP modular basic units, bridges reliably and cost-effectively. Electrolytic capacitors provide the energy without delay when required. Redundancy for even more safety Additional protection against failure of the 24 V DC supply is provided by the redundancy module. Thanks to decoupling via diodes, one failed power supply unit has no influence on the others. In this way, the 24 V DC supply is always secured. Innovative solution for electronic diagnostic The SITOP PSE200U selectivity module is specially tailored to the characteristics of switched-mode power supplies. The electronics permit brief current peaks sbut reliably identify and isolate longer lasting overloads – even on long thin cables and with “creeping“ short circuits in which the current is limited by the high resistance. Miniature circuit breakers do not trip here or they trip too late, even if the power supply could provide the current. The electronic diagnostic module switches the faulty load circuit off reliably while non affected load circuits continue to operate normally, so total failure of the plant can be avoided. The fault is reported via a common signaling contact and indicated by an LED on the affected load circuit. The fault can thus be located quickly and standstill times can be minimized. 8 1 2 3 4 SITOP modular and expansion modules. 1 Signaling module • Floating signal contacts for “output voltage o.k.“ and “operating readiness o.k.“ • Power supply can be turned on and off via remote control • Simply insert and screw the module onto the basic unit 6EP1xxx-3BA00 2 Redundancy module • 2 integral diodes for decoupling two 5 A to 20 A basic units, or one 40 A basic unit • Group signals “Infeed 1 and 2 o.k.“ via green LED and floating relay contact (CO contact) • Monitoring via LED on the unit and relay contact to the upper level control system • Threshold voltage adjustable between 20 to 25 V DC 3 Buffer module • Cost-effective protection against brief power failures up to 10 seconds • Load current to 40 A • Load currents up to 40 A can be protected • Connection to the SITOP modular basic unit via just two cables 4 SITOP PSE200U electronic diagnostic module • Monitoring of up to 4 load circuits • Each output adjustable between 0.5 and 3 A or 3 and 10 A • Safe detection of overloads even on high-resistance cables • Uninterruptible maintenance of the 24 V DC for other loads • Continued operation of non-affected 24 V DC load circuits • Floating common signaling contact for remote diagnosis • Remote reset and reset via pushbutton per circuit • Sequential startup can significantly reduce the total current required from the power supply • Easy to configure The SITOP DC UPS with battery modules protects against long power failures. The innovative UPS500S with long-life capacitors save on battery replacement. Reliable 24 V DC at all times – even when the power fails Power failures can cause plant standstills, take up time, and generate costs. SITOP offers three solutions to counter this: • Buffer module for cost-effective supplementation of the SITOP modular. Electrolytic capacitors buffer the 24 V DC for up to 10 s. • SITOP DC UPS with lead gel batteries for bridging power failures for up to a period of hours to allow processes to continue. • SITOP UPS500, the totally maintenancefree UPS with double-layer capacitors for 24 V DC buffering up to a period of minutes for backing up data and powering down the application. Both DC UPS systems can be easily integrated into PC-based automation solutions using a free software tool. It supports further processing of the status messages, safe powering down, and correct restart of the system. www.siemens.com/sitop-ups SITOP DC UPS with battery modules Maintenance-free DC UPS with capacitors: SITOP UPS500 Compact DC UPS modules ensure continued operation depending on battery capacity and power requirements, even over a period of hours. The high-capacity double-layer capacitors store enough energy for powering down PC-based systems. High availability through battery management The sophisticated battery management system ensures optimal charging of the batteries – and thus reliable battery readiness. The active battery test function even checks the age of the battery. That makes preventive replacement of the battery superfluous – and results in significant cost savings. Extremely communicative All the relevant messages are output via floating contacts, and optionally also via serial interface or USB. • DC UPS modules 6 A, 15 A and 40 A • Maintenance-free battery modules up to 12 Ah • Monitoring of operational readiness, battery feeder, age and charge status • Long service life of the loads and batteries through battery management • Interruption-free transition from standby mode to buffer mode Completely maintenance-free Even in high ambient temperatures, the capacitors still have an extremely long service life. There is no need for maintenance or replacement of the energy store so the investment in the DC UPS pays off after a short time. And because the capacitors do not emit any gases, there is also no need for control cabinet ventilation. Short charging times quickly restore buffer readiness after a power failure. Can be used inside and outside the control cabinet The UPS500S for Din-rail mounting can be supplemented with add-on modules to extend the buffering time. • SITOP UPS500S 15 A, up to 20 kWs • Long service life even at high temperatures • No ventilation of the installation site necessary 9 9 10 1-phase 120 V AC, 230 V AC Output voltage 24 V DC Input voltage 6EP1333-1LB00 6EP1333-2BA20 6EP1333-3BA00 6EP1334-3BA00 40 A 20 A 12.5 A 12 A 6EP1336-2BA10 6EP1334-2AA01-0AB0 6EP1337-3BA00 6EP1336-3BA10 6EP1336-3BA00 6EP1332-5BA20 6EP1334-1LD00 6EP1234-1AA00 6EP1334-1AL12 6ES7307-1KA02-0AA0 6EP1334-2BA20 6EP1333-4BA00 6EP1334-1LB00 10 A 6EP1333-1LD00 6.2 A 6ES7307-1EA01-0AA0 6ES7307-1EA80-0AA0 6EP1332-1SH31 6EP1332-4BA00 6EP1332-1SH71 6ES7307-1BA01-0AA0 SIMATIC design 8A 6EP1233-1AA00 6EP1333-1AL12 6 A 5 A 6EP1332-1LD10 6EP1232-1AA10 6EP1332-5BA10 4 A 6EP1332-1SH52 6EP1332-5BA20 6EP1332-1LD00 3.7 A 3.5 A 3A 6EP1232-1AA00 6EP1332-2BA20 “Special design, special use” 6EP1331-1LD00 6EP1332-5BA00 modular 2.5 A 6EP1332-1SH43 smart 2 A 6EP1331-5BA10 compact 6EP1331-5BA00 6EP1332-1LB00 lite 1.3 A 6EP1331-1SH03 LOGO!Power 0.6 A Output current Selection table SITOP power supplies 6EP1334-1SH01 6EP1332-1SH22 6EP1332-1SH12 Others 11 11 2 A 24 to 110 V DC 20 A Output current 3-phase 400 to 500 V AC 24 V DC 1-phase 120 V AC, 230 V AC 6EP1321- 1SH03 smart 6EP1332-1SH12 6EP1732-0AA0 6EP1457-3BA00 48 V/20 A 6EP1424-3BA00 6EP1456-3BA00 12V/20A 48 V/10 A 6EP1621-2BA00 12 V/2.5 A 6EP1353-2BA00 6EP1322-1LD00 6EP1321-1LD00 “Special design, special use” 6EP1353-0AA00 6EP1323-2BA00 6EP1322-2BA00 modular 2 x 15 V/3.5 A 6EP1352- 1SH03 15 V/4 A 6EP1322-5BA10 6EP1321-5BA00 compact Gray: more information in Catalog KT10.1 or in Online Catalog CA01 3 – 52 V/2 – 10 A 6EP1351- 1SH03 15 V/1.9 A 12 V/14 A 12 V/8.3 A 12V/7 A 12V/6.5 A 12 V/4.5 A 12 V/3 A 6EP1322- 1SH03 6EP1311-1SH13 12 V/1.9 A 12 V/2.0 A 6EP1311- 1SH03 5 V/6.3 A LOGO!Power 5 V/3 A Output voltage 5, 12, 15, 48, … V DC Input voltage 1) 6ES7305-1BA80-0AA0 6EP1731-2BA00 6EP1437-2BA10 6EP1437-2BA00 6EP1334-1SH01 6EP1336-3BA10 6EP1427-3BA00 6EP1436-2BA00 6EP1434-2BA00 Others 6EP1332-1SH22 Connection to 2 phases 230 – 500 V AC – see data sheet SITOP modular 1-/2-phase 88 – 350 V DC 6EP1437-3BA00 6EP1437-3BA10 SIMATIC design 10 A 6EP1437-2BA20 6EP1436-3BA00 6EP1436-3BA10 6EP1436-3BA20 6EP1433-0AA00 “Special design, special use” 4 A 2.5 A 2 A 110 – 350 V DC 0.375 A 48 to 110 V DC 40 A 30 A 20 A 6EP1436-2BA10 6EP1334-3BA00 1) 17A 6EP1333-3BA00 1) modular 5 A 6EP1434-2BA10 smart 10 A Output current 48 to 220 V DC 3-phase 400 to 500 V AC Output voltage 24 V DC Input voltage 12 > 40 ms (at 187 V) 50/60 Hz 0.36 - 0.22 A < 26 A From 10 A characteristic C resp. 16 A characteristic B Mains buffering Rated line frequency Rated input current –– Inrush current –– Recommended miniature circuit breaker < 1.5 W Yes Yes, constant current Class B Not applicable IP20 –20…+70 °C 54 x 90 x 55 0.17 kg CE, cULus, FM, GL, ABS, ATEX, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 $90.00 No-load loss Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Supply harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight approx. Certification US list price $90.00 CE, cULus, FM, GL, ABS, ATEX, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 < 1.8 W 80 % $90.00 CE, cULus, FM, GL, ABS, ATEX, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 < 2 W 80 % Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 77 % Efficiency at rated values, approx. 1.9 A 10.5…16.1 V DC 1.9 A 3.0 A Rated output current (up to +55 °C) 10.5…16.1 V DC 5 V DC ± 3 % 4.6…5.4 V DC Rated output voltage –– Tolerance –– Setting range 15 V DC 0.63 - 0.33 A < 25 A 12 V DC 0.53 - 0.30 A < 25 A 6EP1351-1SH03 100 – 240 V AC 85...264 V AC/110...300 V DC 6EP1321-1SH03 6EP1311-1SH03 Rated input voltage –– Range 15 V/1.9 A 54 mm design Order no. 12 V/1.9 A 5 V/3 A SITOP Technical data $64.00 CE, cULus, FM, GL, ABS, ATEX, SEMI F47, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 < 2 W 85 % 1.3 A 22.2…26.4 V DC 24 V DC 0.70 - 0.35 A < 25 A 6EP1331-1SH03 24 V/1.3 A LOGO!Power Flat power supply for distribution boards 1.13 - 0.61 A < 55 A 1.24 - 0.68 A < 55 A < 1.9 W 85 % $119.00 CE, cULus, FM, GL, ABS, ATEX, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 0.25 kg 72 x 90 x 55 –20…+70 °C IP20 Not applicable Class B $119.00 CE, cULus, FM, GL, ABS, ATEX, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 $119.00 CE, cULus, FM, GL, ABS, ATEX, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 < 2.3 W 85 % 4.0 A 10.5…16.1 V DC 10.5…16.1 V DC 4.5 A 15 V DC 12 V DC Yes, constant current Yes < 1.5 W 83 % 6.3 A 5 V DC ± 3 % 4.6…5.4 V DC From 10 A characteristic C resp. 16 A characteristic B 0.71 - 0.37 A < 50 A 50/60 Hz > 40 ms (at 187 V) 6EP1352-1SH03 15 V/4 A 72 mm design 6EP1322-1SH03 12 V/4.5 A 100 – 240 V AC 85…264 V AC/110...300 V DC 6EP1311-1SH13 5 V/6.3 A $84.00 CE, cULus, FM, GL, ABS, ATEX, SEMI F47, NEC Class 2, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 < 1.8 W 88 % 2.5 A 22.2…26.4 V DC 24 V DC 1.22 - 0.66 A < 46 A 6EP1332-1SH43 24 V/2.5 A 90 mm design $115.00 CE, cULus, FM, GL, ABS, ATEX, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 0.34 kg 90 x 90 x 55 –20…+70 °C IP20 Yes Class B Yes, constant current Yes < 2 W 89 % 4.0 A 24 V DC ± 3 % 22.2…26.4 V DC From 10 A char. C resp. 16 A char. B 1.95 - 0.97 A < 30 A 50/60 Hz > 40 ms (at 187 V) 100 – 240 V AC 85…264 V AC/ 110...300 V DC 6EP1332-1SH52 24 V/4 A 13 0.6 A (up to +55 °C) +55°C to 70°C Rated output current – Derating Yes Yes, restart Class B Not applicable IP 20 –20...+70 °C 22.5 x 80 x 100 0.12 kg removable screw terminals CE, cULus, cCSAus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 $51.00 Can be switched in parallel Electronic short-circuit protection Radio suppression level (EN 55022) Supply harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight, approx. Connections1) Certification US list price $66.00 CE, cULus, cCSAus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 removable screw terminals 0.17 kg 30 x 80 x 100 –20...+70 °C IP 20 Not applicable Class B Yes, restart $86.00 CE, cULus, cCSAus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 removable screw terminals 0.17 kg 30 x 80 x 100 –20...+70 °C IP 20 Not applicable Class B Yes, restart Yes < 0.5 W 82 % 2 A (up to +55 °C) +55 °C to 70 °C Can be used with spring loaded terminals instead, part number 6EP1971-5 BA00 (100 pieces for 50 units). Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 1) < 0.75 W < 0.5 W No-load loss Yes 86 % Efficiency with rated values, approx. 82 % 1.3 A (up to +55 °C) +55 °C to 70 °C 24 V DC ± 3 % 22.2...26.4 V DC 24 V DC ± 3 % – Rated output voltage – Tolerance – Setting range 12 V DC ± 3 % 10.5…12.9 V DC 50/60 Hz 0.63 to 0.31 A from 10 A characteristic C from 16 A characteristic B 50/60 Hz 0.63 to 0.31 A from 10 A characteristic C from 16 A characteristic B 50/60 Hz 0.28 to 0.12 A from 10 A characteristic C from 16 A characteristic B Rated line frequency Rated input current – Recommended MCB 50/60 Hz $86.00 CE, cULus, cCSAus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 50/60 Hz 100 to 230 V AC 85…264 V AC/110…300 V DC 6EP1322-5BA10 0.32 kg 52.5 x 80 x 10 0 -20..+70°C IP 20 Not Applicable Class B Yes, restart Yes <0.75 W 88% 4A (up to +50°C) +50°C to 70°C 24V DC ±3% 22.2..26.4V DC $124.00 CE, cULus, cCSAus, ATEX,GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 $130.00 CE, cULus, cCSAus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 removable screw terminals 0.32 kg 52.5 x 80 x 100 -20..+70°C IP 20 Not Applicable Class B Yes, restart Yes <0.75 W 85% 6.5A (up to +50°C) +50°C to 70°C 12V DC ±3% 10.5..12.9V DC 1.6 to 0.75 A 1.6 to 0.75 A From 10 A characteristic C From 10 A characteristic C From 16 A characteristic B From 16 A characteristic B 50/60 Hz removable screw terminals removable screw terminals 0.22 kg 45 x 80 x 100 -20..+70°C IP 20 Not Applicable Class B Yes, restart Yes <0.75 W 89% 2.5A (up to +50°C) +50°C to 70°C 24V DC ±3% 22.2..26.4V DC 1.33 to 0.67 A From 10 A characteristic C From 16 A characteristic B 100 to 230 V AC 85…264 V AC/110…300 V DC 12V/6.5A Typ. 20 ms (at 120/230V AC) Typ. 20 ms (at 120/230V AC) Typ. 20 ms (at 120/230V AC) Typ. 20 ms (at 120/230V AC) 6EP1332-5BA00 100 to 230 V AC 100 to 230 V AC 85...264 V AC/110…300 V DC 85…264 V AC/110…300 V DC 6EP1321-5BA00 6EP1332-5BA10 Typ. 20 ms (at 120/230V AC) Typ. 20 ms (at 120/230V AC) 6EP1331-5BA10 Mains buffering Overall width 52.5 mm 100 to 230 V AC 100 to 230 V AC 85...264 V AC/110…300 V DC 85...264 V AC/110…300 V DC 24V/4 A Rated input voltage – Range Overall width 45mm 24V/2.5A 6EP1331-5BA00 12 V/2 A Overall width 30 mm Order No. 24 V/1.3 A Overall width 22.5 mm 24 V/0.6 A Technical data Output voltage/current SITOP compact Compact power supply for control boxes 14 3 A Characteristic C 24 V DC + 3% 22.8...26.4 VDC 2.5 A from +45°C (2%/K) 85% < 0.5 W Yes, constant current Class A Not applicable IP20 0...+60 °C 32.5 x 125 x 125 0.4 kg CE, cULus $100.00 – Recommended miniature circuit breaker Rated output voltage – Tolerance – Setting range Rated output current – Derating Efficiency with rated values, approx. No-load loss Parellel switching Electronic short-circuit protection Radio interference suppression (EN 55022) Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight, approx. Certification US list price Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 1.1/0.65 A <27 A Rated input current – Inrush current $135.00 CE, cULus 0.5 kg 50 x 125 x 125 0...+60 °C IP20 Yes Class A Yes, constant current < 0.75 W 86% 5A from +45°C (2%/K) 24 V DC + 3% 22.8...26.4 VDC 6 A Characteristic C 2.1 /1.15 A <32 A 50/60 Hz $196.00 CE, cULus 0.75 kg 70 x 125 x 125 0...+60 °C IP20 No Class A Yes, constant current < 0.5 W 90% 10 A from +45°C (2%/K 24 V DC + 3% 22.8...26.4 VDC 10 A Characteristic C 4.3/2.4 A <65 A 50/60 Hz > 20 ms (at 93/187 V) > 20 ms (at 93/187 V) > 20 ms (at 93/187 V) 50/60 Hz Mains buffering Rated line frequency 120 to 230 V AC x 85...132 /170…264 V AC 120 to 230 V AC 85...132 /170…264 V AC 24 V /10 A 120 to 230 V AC 85...132 /170…264 V AC Rated input voltage – Range SITOP lite 6EP1334-1LB00 6EP1332-1LB00 Order No. 24 V / 5 A 6EP1333-1LB00 24 V / 2.5 A Output voltage/current Technical data lite Cost-effective power supply for basic applications 15 -10…+70 °C $205.00 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change $199.00 $285.00 0.8 kg $116.00 0.5 kg US list price 0.5 kg 0.32 kg 70 x 125 x 125 -10…+70 °C IP20 Yes CE, UL, CSA, GL 1), ATEX, Hazardous Location Class I Div 2 Groups A, B, C & D, T4 50x125x125 -10…+70 °C IP20 Yes Weight approx. 50x125x125 Yes Class B 10 A (12 A to +45 °C) Certification -10…+70 °C 32.5 x 125 x 125 Ambient temperature IP20 Degree of protection (EN 60529) Dimensions (W x H x D) in mm IP20 Not applicable Line harmonics limitation (EN 61000-3-2) Class B Class B Radio interference suppression (EN 55022) Class B Yes, constant current Electronic short-circuit protection Yes Yes Yes Yes Extra power: 1.5 x rated output current for 5 s/min Switching in parallel Brief overload characteristics 87% 84% 88 % 85 % +55- 70°C Efficiency at rated values approx. +55- 70°C 7A (7A to +45 °C) +60- 70°C +60- 70°C Rated output current – Derating 5 A (6 A to +45 °C) 2.5 A (3 A to +45 °C) Rated output current 10A characteristic C 4 V DC ± 3 % 22.8…28 V DC 6A characteristic C 12V DC ±3% 11.5...15.5 V DC 6A characteristic C 24 V DC ± 3 % 22.8…28 V DC 3 A characteristic C 24 V DC ± 3 % 22.8…28 V DC Rated output voltage – Tolerance – Setting range 4.49 A < 65 A 50/60 Hz 50/60 Hz 1.73 /0.99 A < 60 A > 20 ms (at 93/187 V) 50/60 Hz 12V/14 A 6EP1323-2BA00 24 V/10 A Wallmount 6EP1334-2AA01-0AB0 $295.00 0.8 kg 70 x 125 x 125 IP20 Yes Class B Yes 87% $420.00 0.85 kg 70 x 125 x 125 0…+60 °C IP 20 Yes Class B Yes 90 % 10 A (12 A to +45 °C) +60- 70°C 14A (14A to +45 °C) 24 V DC ± 3 % 22.8…28 V DC 10A characteristic C 4.1/2.0 A < 65 A 50/60 Hz > 20 ms (at 93/187 V) +55- 70°C 12V DC ±3% 11.5...15.5 V DC 10A characteristic C 3.24/1.41A < 60 50/60 Hz > 20 ms (at 93/187 V) 120/230V AC 85...132/170..264V AC, automatic range switching 1) 6EP1334-2BA20 24V/10 A SITOP smart 1-phase >20 ms (at 93/187 V) 2.34/1.36 A < 40 A – Recommended 1) miniature circuit breaker 50/60 Hz 1.25/ 0.74 A < 33 A Rated line frequency > 20 ms (at 93/187 V) > 20 ms (at 93/187 V) Mains buffering Rated input current – Inrush current (25 °C) 120/230 V AC 85…132/170…264 V AC, automatic range switching 1) Rated input voltage – Range 12V/7 A 6EP1322-2BA00 24 V/5 A 6EP1333-2BA20 24 V/2.5 A 6EP1332-2BA20 Order no. Technical data Output voltage/current new! SITOP smart Powerful standard power supply GL is pending for the new SITOP smart units 6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20. 1) 24 V/ 20 A $420.00 CE, cULus, cCSAus Class 1 Div 2, ATEX, GL 2.4 kg 115 x 145 x 150 0…+70 °C IP 20 Yes Class B Yes, restart Yes 90 % +60- 70°C 20 A (24A to +45 °C) 24 V DC ± 3 % 22.8…28 V DC 10A characteristic C 7.5/3.5 A <11 A 50/60 Hz > 20 ms (at 93/187 V) 6EP1336-2BA10 16 Yes, restart Class B Yes IP20 Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change $340.00 Extra-Power: 1.5 x rated output current for 5 s/min, 120% permanently up to 45°C Brief overload characteristics US list price Yes Switching in parallel CE, cULus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 91% Efficiency at rated values approx. 1.6 kg 10 A Rated output current Certification 24 V DC ± 3% 24 … 28 V DC Rated output voltage – Tolerance – Setting range Weight approx. from 6 … 16 A Characteristic C, 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 – Recommended miniature circuit breaker 0 … +70 °C 0.7-0.5 A < 36 A Rated input current – Inrush current (25 °C) 90 x 145 x 150 50/60 Hz Rated line frequency Dimensions (W x H x D) in mm > 6 ms (at 400 V) Mains buffering Ambient temperature 400-500 V 3 AC 340 … 550 V 3 AC Rated input voltage – Range $370.00 CE, cULus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 1.6 kg 90 x 145 x 150 0...+60 °C 91 % 20 A 1.2 –1.0 A < 36 A 6EP1436-2BA10 6EP1434-2BA10 SITOP smart 3-phase Order no. 24 V/20 A 24 V/10 A Output voltage/current Technical data SITOP smart Powerful standard power supply 24 V/40 A $580.00 CE, cULus, ATEX, GL, Hazardous Locations Class I Div 2, Groups A, B, C and D, T4 3.7 kg 150 x 145 x 150 0 … +60 °C 91.5% 40 A from 10 … 16 A Characteristic C, 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 1.7-1.5 A < 60 A 6EP1437-2BA20 17 40 A 120A 20 A 60A from +60 °C 20 A 60A 30A from +60 °C 10 A 30A from +60 °C 5 A 15A from +60 °C 87 % Yes, output characteristic can be switched to parallel operation Yes, constant current or latching shutdown selectable. Constant current: 1.15 x rated output current Class B Yes IP20 -25…+70 °C 70 x 125 x 125 1.2 kg CE, cULus, GL, ABS, SEMI F472) $215.00 Rated output current – Overload behavior (power boost for 25 ms) – Overload behavior (power boost for 5 ms) – Derating Efficiency at rated values, approx. Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Supply harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight approx. Certification US list price 4) $515.00 CE, cULus, GL, ABS 1.5kg 90 x 125 x 125 -25…+70 °C IP20 Yes Class B 93 % > 25 ms (at 120/230 V) In conjunction with a buffer module In conjunction with two buffer modules $340.00 CE, cULus, GL, ABS, SEMI F472) 1.4 kg 90 x 125 x 125 -25…+70 °C IP20 Yes Class B 87 % > 25 ms (at 120/230 V) Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 2) Connection to 2 phases of a three-phase supply system At input voltage 208 to 230 V AC 24 V DC ± 3 % 24…28.8 V DC 24 V DC ± 3 % 24…28.8 V DC 24 V DC ± 3 % 24…28.8 V DC 24 V DC ± 3 % 24…28.8 V DC 24 V DC ± 3 % 24…28.8 V DC Rated output voltage – Tolerance – Setting range 3) 15.0/8.0 A < 125 A 20 A charact. C or 3RV1421-xxA10 7.7/3.5 A < 60 A 10 A charact. C or 3RV2411-1xA10 4.6 – 2.5 A < 20 A 6 A charact. C or 3RV1021-1xA10 4.4 to 2.4/2.4 to 1.1 A < 35 A 6 A charact. C or 3RV1021-1xA10 2.2 to 1.2/1.2 to 0.61 A < 35 A 6 A charact. C or 3RV1021-1xA10 Rated input current – Inrush current (25 °C) – Recommended miniature circuit breaker 1) 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz $480.00 CE, cULus,GL, ABS, SEMI F473) 1.2 kg 160 x 125 x 125 0…+70 °C IP20 Yes Class B 89 % > 20 ms (at 230 V) $750.00 CE, cULus, SEMI F474) 2.9 kg 240 x 125 x 125 0…+70 °C IP20 No Class B 88 % from +60 °C > 20 ms (at 230 V) 120/230 V AC 85…132/176...264 V, start-up 95/ 190 V > 25 ms (at 120/230 V) 120/230 V AC AC 85…275 V oder DC 88…350 V 6EP1337-3BA00 Rated line frequency 120 – 230/230 – 500 V AC 85…264/176…550 V AC 120/230 V AC 85…132 /176… 264 V, start-up 93/ 183 V Mains buffering 24 V/40 A 6EP1336-3BA00 24 V/20 A 120 – 230/230 – 500 V AC 85…264/176…550 V AC 6EP1336-3BA10 24 V/20 A, PSU100M Rated input voltage – Range 6EP1334-3BA00 6EP1333-3BA00 24 V/10 A 24 V/5 A Order no. SITOP modular 1-phase and 2-phase1) Output voltage/current Technical data SITOP modular Technology power supply for demanding solutions 18 50/60 Hz 2.2 A (at 400 V) < 70 A 6-16 A Charact. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 48 V DC ± 3 % 42…56 V DC 50/60 Hz 1.2-1.0 A < 18 A 6-16 A Charact. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 48 V DC ± 3% 42…56 V DC 50/60 Hz 2.0 – 1.7 A < 70 A 6-16 A Charakt. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 24 V DC ± 3 % 24…28.8 V DC 50/60 Hz 2.6 – 1.2 A < 56 A 6-16 A Charakt. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 24 V DC ± 3 % 24…28.8 V DC 50/60 Hz 1.1 – 0.9 A < 35 A 6-16 A Charakt. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 24 V DC ± 3 % 24…28.8 V DC 20 A 1.2-1.0 A < 18 A 6-16 A Charakt. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 24 V DC ± 3 % 24…28.8 V DC Rated input current – Inrush current (25 °C) – Required miniature circuit breaker Rated output voltage – Tolerance – Setting range 1.5 x rated output current Power boost: 3 x rated output current for 25 ms, extra power1): 1.5 x rated output current for 5 s/min Yes, automatic restart or user directed restart selectable. Constant current: approx. 1.15 x rated output current Class B Yes IP20 -25…+60 °C 70 x 125 x 125 1.2 kg CE, cULus, SEMI F47, ABS, GL $440.00 Extra Power for 5 s/min Brief overload characteristics Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight approx. Certification US list price $450.00 CE, cULus, SEMI F47, ABS, GL 2.0 kg 160 x 125 x 125 0…+60 °C IP20 Yes Class B - 3 x rated output current Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 3 x rated output current 25 ms power boost $690.00 CE, cULus, SEMI F47, ABS, GL 3.4 kg 150 x 125 x 150 -25…+60 °C IP20 Yes Class B 1.5 x rated output current 3 x rated output current 40 A $715.00 CE, cULus, SEMI F47 3.2 kg 240 x 125 x 125 0…+60 °C IP20 Yes Class B - 3 x rated output current 90 % Yes, output characteristic can be switched to parallel operation 40 A 93 % Switching in parallel 90 % 20 A 93 % > 6 ms (at 400 V) Rated output current > 15 ms (at 400 V) Efficiency at rated values, approx. > 6 ms (at 400 V) $475.00 CE, cULus, ABS, GL 1.2 kg 70 x 125x 125 -10...+60°C IP 20 Yes Class B 1.5 x rated output current 2.3 x rated output current 93% 10 A > 15 ms (at 400 V) $720.00 CE, UL, CSA, ABS, GL 3.2 kg 240 x 125 x 125 0…+60 °C IP20 Yes Class B 3 x rated output current 90 % 20 A > 6 ms (at 400 V) 400 – 500 V 3 AC 340…550 V 3 AC 6EP1457-3BA00 50/60 Hz 400-500 V 3 AC 320…575 V 3 AC 6EP1456-3BA00 > 15 ms (at 400 V) 400 – 500 V 3 AC 340…550 V 3 AC 6EP1437-3BA00 Rated line frequency 400 – 500 V 3 AC 320…575 V 3 AC 6EP1437-3BA10 Mains buffering 400 – 500 V 3 AC AC 340…550 V 3 AC 6EP1436-3BA00 48 V/20 A SITOP modular 3-phase, 48 V 400 – 500 V 3 AC 320…575 V 3 AC 48 V/10 A Rated input voltage – Range 24 V/40 A 6EP1436-3BA10 24 V/40 A SITOP modular 3-phase Order no. 24 V/20 A 24 V/20 A Technical data Output voltage/current 19 0.65 A < 30 A 10A characteristic C,16 A characteristic B 12 V DC ± 2% 11…14 V DC 3 A from +50ºC (2.5%/K) – Recommended miniature circuit breaker Rated output voltage – Tolerance – Setting range Output current – rated value – Derating CE, cULus and cURus $59.00 Certification US list price 97 x 128 x 38 $59.00 CE, cULus and cURus 0.35 kg Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 97 x 98 x 38 0.37 kg Dimensions (W x H x D) in mm Weight approx. -10…+70 °C -10…+70 °C IP20 Wall mounting, variable installation position IP20 Degree of protection (EN 60529) Not applicable Ambient temperature Not applicable Suppy harmonics limitation (EN 61000-3-2) Class B Yes, restart Yes 86 % 2.1 A from +50ºC (2.5%/K) 24 V DC ± 2% 22…28 V DC 1.1-0.7 A < 60 A 100-240 V AC Installation Yes, restart Class B Electronic short-circuit protection Radio interference suppression (EN 55022) 84 % 50/60 Hz Rated line frequency Rated input current – Inrush current (25 °C) Yes 50/60 Hz > 15 ms (at 115/230 V) Mains buffering Efficiency at rated values, approx. > 15 ms (at 115/230 V) 85…264 V AC – Range Parallel switching 85…264 V AC 100-240 V AC Rated input voltage 6EP1331-1LD00 6EP1321-1LD00 Order no. PSU100D direct mount 24 V/2.1 A 12 V/3 A Output voltage/current Technical data SITOP in special design, for special uses 24 V/3.1 A $67.00 CE, cULus and cURus 0.37 kg 97 x 128 x 38 -10…+70 °C IP20 Yes Class B Yes, restart Yes 86 % 3.1 A from +50ºC (2.5%/K) 24 V DC ± 2% 22…28 V DC 1.5-1.0 A < 60 A 50/60 Hz > 15 ms (at 115/230 V) 85…264 V AC 100-240 V AC 6EP1332-1LD00 20 100-240 V AC 85…264 V AC > 15 ms (at 115/230 V) 50/60 Hz 2.0–1.1 A < 75 A 100-240 V AC 85…264 V AC > 15 ms (at 115/230 V) 50/60 Hz 2.0-1.1 A < 75 A Rated input voltage – Range Mains buffering Rated line frequency Rated input current – Inrush current (25 °C) 0.50 kg CE, cULus and cURus $74.00 Certification US list price $74.00 CE, cULus and cURus 0.57 kg 97 x 158 x 38 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 97 x 158 x 38 Weight approx. Wall mounting, variable installation position Dimensions (W x H x D) in mm Installation IP20 -10…+70 °C IP20 Yes -10…+70 °C Yes Suppy harmonics limitation (EN 61000-3-2) Class B Yes, restart Degree of protection (EN 60529) Class B Electronic short-circuit protection Radio interference suppression (EN 55022) Yes Ambient temperature Yes, restart Switching in parallel 84 % 86 % Yes Efficiency at rated values, approx. 8.3 A from +50ºC (2.5%/K) 4.1 A from +50ºC (2.5%/K) Output current – rated value – Derating 12 V DC ± 2% 11…14 V DC 24 V DC ± 2% 22…28 V DC Rated output voltage – Tolerance – Setting range $80.00 CE, cULus and cURus 0.55 kg 97 x 178 x 38 -10…+70 °C IP20 No Class B Yes, restart Yes 86 % 6.2 A from +50ºC (2.5%/K) 24 V DC ± 2% 22…28 V DC 3.1–2.0 A < 75 A 50/60 Hz > 15 ms (at 115/230 V) 100-240 V AC 85…264 V AC 6EP1333-1LD00 24 V/6.2 A PSU100D direct mount 10A characteristic C,16 A characteristic B 6EP1322-1LD00 6EP1332-1LD10 Order no. – Recommended miniature circuit breaker 12 V/8.3A 24 V/4.1 A Output voltage/current Technical data SITOP in special design, for special uses $95.00 CE, cULus and cURus 0.81 kg 105 x 199 x 38 -10…+70 °C IP20 Yes Class B Yes, restart Yes 86 % 12.5 A from +50ºC (2.5%/K) 24 V DC ± 2% 22…28 V DC 4.0–2.0 A < 60 A 50/60 Hz > 15 ms (at 115/230 V) 100-240 V AC 85…264 V AC 6EP1334-1LD00 24 V/12.5 A 21 12 V DC ± 3 % 12…14 V DC 50/60 Hz 1.88/0.95 A < 30 A 10 A charact. C, 16 A charact. B 24V DC ± 3 % 22.2...26.4 V DC Rated line frequency Rated input current – Inrush current (25 °C) – Recommended miniature circuit breaker Rated output voltage – Tolerance – Setting range CE, cCSAus, cULus, Class 2 $159.00 US list price $250.00 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change Only permissible at an ambient temperature of 0 to 50 °C 0.26 kg 0.32 kg Certification 1) 32.5 x 125 x 125 52.5 x 80 x 100 CE, cULus DIN rail DIN rail Installation Dimensions (W x H x D) in mm Weight approx. IP20 0…+60 °C IP20 Yes -20...+70 °C Yes Class B Ambient temperature Class B Yes Yes, 2 units 80 % 2.5 A < 20 A for 20 ms 1.6 A – > 5 ms 24 V DC 18.5…30.2 V DC 6EP1621-2BA00 Yes, constant current No Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) 87% Efficiency at rated values, approx. Rated output current – Derating 3.7 A up to 50ºC, 1.1A up to 70ºC 10 A charact. B 110-230V AC 85...264V AC/ 100...300V DC > 20 ms (at 120/230 V AC) Rated input voltage – Range Mains buffering 6EP1332-5BA20 Order no. 12 V/2.5 A 24 V/3.7 A Output voltage/current SITOP DC/DC Class 2 approval Technical data SITOP in special design, for special uses SITOP PSU400M CE, cULus, GL, (ABS in preparation) $525.00 1.22 kg 90x125x125 DIN rail -25…+70 °C IP20 No Class A (emission) Yes, constant current or latching shutdown selectable No 20 A 30A for 5ms from 60ºC, (5.5%/K), 200…300 V DC, 820…900 V DC 95% 24V DC ± 3 % 24…28.8 V DC <8A 0.85 A — 600 V DC 200...900 V DC, start-up from approx. 400 V — 6EP1536-3AA00 24V/20 A SITOP dual SITOP flat design 24 V/10 A $400.00 CE 0.75 kg 0.6 kg $410.00 CE, cULus $530.00 CE, cULus 0.72 kg 160 x 130 x 60 Standard mounting rail 160 x 130 x 60 Standard mounting rail 75 x 125 x 125 DIN rail 0…+60 °C 0…+60 °C 0…+60 °C (Derating from 45 °C) IP20 No Class B Yes, restart Yes 89 % 10 A 24 V DC ± 1 % 24…28.8 V DC From 10 A charact. C < 65 A 4/2.5 A 50/60 Hz 120/230 V AC 85…132/ 170…264 V AC > 20 ms (at 93/187 V) 6EP1334-1AL12 IP20 No Class B Yes, restart Yes 88 % 5 A 24 V DC ± 1 % 24…28.8 V DC From 6 A charact. C < 32 A 2.2/1.2 A 50/60 Hz 120/230 V AC 85…132/ 170…264 V AC > 20 ms (at 93/187 V) 6EP1333-1AL12 24 V/5 A IP20 No Class A Yes, restart Yes 80 % 2 x 3.5 A (2 x 2.5 A from 45 °C) 2 x 15 V DC ± 3 % 14.5…17 V DC 10 A charact. C, 16 A charact. B < 30 A, < 3 ms 1.6/1.0 A 50/60 Hz > 10/40 ms (at 120/187 V) 120 – 230 V AC 93…264 V AC 6EP1353-0AA00 2 x 15 V/3.5 A 22 400/500V 3 AC 320...550 V 3 AC > 50 ms (at 400 V) 50/60 Hz 0.36/0.29 A < 15 A A charact. C or B 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 24 V DC ± 3% 24...29V DC 5A 90% No Class A No IP20 42 x 125 x 125 0.6 kg CE, cULus $295.00 120/230 V AC 85…132 V/170…264 V AC > 10 ms (at 93/187 V) 50/60 Hz 2.2/0.9 A < 32 A From 10 A charact. C 24 V DC ± 1 % 3…52 V DC 2 to 10 A (max. 125 W) 84 % (at 24 V/5 A) Yes Yes, constant current Class B Yes IP20 0…+60 °C DIN rail 75 x 125 x 125 0.9 kg CE, cULus $350.00 Rated input voltage – Range Mains buffering Rated line frequency Rated input current – Inrush current (25 °C) – Recommended miniature circuit breaker Rated output voltage – Tolerance – Setting range Rated output current – Derating Efficiency at rated values, approx. Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Installation Dimensions (W x H x D) in mm Weight approx. Certification US list price DIN rail 0…+60 °C Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 6EP1433-0AA00 6EP1353-2BA00 Order no. Yes, restart 24 V/5A 3…52 V/10A Output voltage/current SITOP PSU300E SITOP flexi Technical data new! SITOP in special design, for special uses Yes 93% 20 A from +60ºC (3%/K) 24V DC ± 3% 24...28.8 V DC 6–16 A charact. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 C <18 A 1.2/1.0 A 50/60 Hz > 20 ms (at 400 V) 400/500V 3 AC 320...575V 3 AC 6EP1436-3BA20 24 V/17 A $435.00 CE, cULus 1.2 kg 70 x 125 x 125 DIN rail -25ºC…+60 °C IP20 Yes Class B $435.00 CE, cULus (pending) 1.2 kg 70 x 125 x 125 DIN rail -25ºC…+70 °C IP20 Yes Class B $610.00 CE, cULus 3.4 kg 150 x 125 x 150 DIN rail -25ºC…+70 °C IP20 Yes Class B Yes 93% 30 A from +60ºC (1.7%/K) 24 V DC ± 3% 24...28.8 V DC 10–16 A charact. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 < 56 A 1.6/1.3A 50/60 Hz > 20 ms (at 400 V) 400/500V 3 AC 320...575V 3 AC 6EP1427-3BA00 24 V/30 A SITOP PSU300B for battery charging Yes, constant current or latching shutdown selectable Yes 88 % 20 A — 12 V DC ± 3% 12...14 V DC 6–16 A charact. C 3-ph. coupled or 3RV2011-1DA10 or 3RV2711-1DD10 <18 A 0.7/0.6 A 50/60 Hz > 15 ms (at 400 V) 400/500V 3 AC 320...575V 3 AC 6EP1424-3BA00 12 V/20 A 23 Class B Yes 2.5 A 83 % Yes, 2 units Yes, restart Class B Not applicable IP20 Rated output current Efficiency at rated values, approx. Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) $123.00 US list price $160.00 Condensation permissible, increased vibration and shock resistance $172.00 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 1) $230.00 $295.00 CE, cULus, ATEX, Hazardous Location Class I Div 2 Groups A, B, C & D, T4 0.8 kg 80 x 125 x 120 CE, cULus, ATEX, GL, ABS, CE, cULus Hazardous Location Class I Div 2 Groups A, B, C & D 0.6 kg 60 x 125 x 120 Certification 0.4 kg 40 x 125 x 120 0.3 kg 0.5 kg 160 x 80 x 62 70 x 100 x 75 0…+60 °C Weight approx. 0…+60 °C Dimensions (W x H x D) in mm 0…+60 °C 0…+60 °C DIN rail or wall mounting Can be mounted on S7 rail. Mounting adapter for DIN rail 35 x15 mm: 6EP1971-1BA00 0…+60 °C IP20 Yes Class B Yes, restart Yes 90 % 10 A – ± 3 % 24 V DC 10 A charact. C 4.2/1.9 A < 55 A 50/60 Hz > 20 ms (at 93/187 V) 85…132 V/170…264 V AC 120/230 V AC automatic range selection 6ES7307-1KA02-0AA0 24 V/10 A DIN rail IP20 Yes Class B Yes, restart Yes 86 % 5 A – ± 3 % 24 V DC 6 A charact. C 2.3/1.2 A < 20 A 50/60 Hz > 20 ms (at 93/187 V) 85…132 V/170…264 V AC 120/230 V AC automatic range selection 6ES7307-1EA01-0AA0 24 V/5 A Installation IP20 Not applicable Class B Yes, restart Yes 84 % 2 A – ± 3 % 24 V DC 3 A charact. C 0.9/0.5 A < 22 A 50/60 Hz > 20 ms (at 93/187 V) 85…132 V/170…264 V AC 120/230 V AC automatic range selection 6ES7307-1BA01-0AA0 24 V/2 A SIMATIC S7-300 design Ambient temperature IP20 Yes, restart Yes, up to 5 units 84 % 3.5 A – ± 5 % – 1.65/0.95 A < 33 A – Setting range 1.2/0.67 A < 13 A Rated input current – Inrush current (25 °C) 50/60 Hz 24 V DC 50/60 Hz Rated line frequency > 20 ms (at 93/187 V) 93…132 V/187…264 V AC ± 3 % > 20 ms (at 93/187 V) Mains buffering 24 V DC 85…132 V/176…264 V AC – Range 120/230 V AC 6EP1332-1SH31 – Tolerance 120/230 V AC Rated input voltage Rated output voltage 6EP1332-1SH71 Order no. 24 V/3.5 A 10 A charact. C, 6 A charact. D 24 V/2.5 A – PM1207 Output voltage/current SIMATIC S7-200 design – Recommended 16 A charact. B, miniature circuit breaker 10 A charact. C SIMATIC S7-1200 design Technical data SITOP in SIMATIC design $265.00 CE, UL, CSA 0.57 kg 80 x 125 x 120 Can be mounted on S7 rail. Mounting adapter: 6ES7390-6BA00-0AA0 –25…+70 °C IP20 No Class A Yes, restart No 84 % 5 A – ± 3 % 24 V DC 10 A charact. C 2.2/1.2 A < 45 A 50/60 Hz > 20 ms (at 93/187 V) 93…132 V/187…264 V AC 120/230 V AC 6ES7307-1EA80-0AA0 24 V/5 A Outdoor 1) 24 Yes on S7-1500 system carrier 75 x 147 x 135 3 A (4.5A for 5s/min) 87% Yes Yes, restart Class B Not applicable IP20 0…+60 °C on S7-1500 system carrier 50 x 147 x 135 0.45 kg CE, cULus, FM, ATEX, pending: Hazardous Location Class I Div 2 Groups A, B, C & D, T4, GL, and ABS $186.00 Efficiency at rated values, approx. Switching in parallel Electronic short-circuit protection Radio interference suppression (EN 55022) Line harmonics limitation (EN 61000-3-2) Degree of protection (EN 60529) Ambient temperature Installation Dimensions (W x H x D) in mm Weight approx. Certification US list price $265.00 0.74 kg 0…+60 °C IP20 Yes, restart Yes 91% 8 A (12 A for 5s/min) – Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change Class B – ±3% Rated output current 3.7A/1.7A < 67 A 50/60 Hz – Setting range Rated input current – Inrush current (25 °C) > 20 ms (at 93/187 V) 24 V DC 1.4A/0.8A < 23 A Rated line frequency 85...132/176...264 V AC ±3% 50/60 Hz Mains buffering 24 V DC > 20 ms (at 93/187 V) – Range 120/230 V AC automatic range detection 6EP1333-4BA00 – Tolerance 85...132/176...264 V AC Rated input voltage 24V/8A - PM 1507 Rated output voltage 120/230 V AC automatic range detection Order no. 10A charact. C 16A charact. B 6EP1332-4BA00 Output voltage/current – Recommended 6A charact. C miniature circuit breaker 10A charact. B SIMATIC S7-1500 design 24V/3A - PM 1507 Technical data new! SITOP in SIMATIC design 25 Signaling module 1) 6EP1961-3BA10 Contact rating 240 V AC/6 A Signaling module for snapping onto the side of the basic unit; automatic contacting, with floating signaling contacts for “Output voltage o.k.“ and “operating readiness o.k.“; with signal input for switching the basic unit ON/OFF remotely. Not applicable SITOP Order no. Rated input voltage – Range Brief description of product/function Rated output current 6EP1961-3BA21 IP20 0…+ 60 °C 25 x 125 x 125 0.15 kg CE, UL, CSA $122.00 Degree of protection (EN 60529) Ambient temperature Dimensions (W x H x D) in mm Weight approx. Certification US list price $265.00 CE, UL, CSA, GL, ABS 1.2 kg 70 x 125 x 125 0…+60 °C Can only be combined with SITOP modular power supply 6EP1__-3BA00 Can only be combined with SITOP modular power supply 24 V DC Max. 8 A summation current in fault case in accordance with NEC Class 2 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 3) 2) 1) Class B Class B Radio interference suppression (EN 55022) IP20 No Yes Not applicable Electronic shortcircuit protection $150.00 24 V DC 19…29 V DC 6EP1962-2BA00 0.125 kg 30 x 80 x 100 -20…+70 °C IP20 Class B No No 97% 10 A (Total output current) Decoupling of two 5 A poer supplies for one 10A poer supply per redundancy module. $78.00 $165.00 Class 2 CE, cULus, NEC 0.125 kg 30 x 80 x 100 -20…+70 °C IP20 Class B No No 95% 3.5 A 3) Decoupling and limitation of the output to Class 2 limit (100 W) of two power supplies 5 to 40 A. Module for redundancy mode Floating relay contact and gre LED for signaling, Infeed 1 and 2 o.k.“, switching threshold adjustable between 20 to 25 V DC. 24 V DC 19…29 V DC 6EP1964-2BA00 CE, cULus CE, cULus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C & D, T4 1.0 kg 70 x 125 x 125 0…+60 °C IP20 Class B No Yes Not applicable Switching in parallel 97 % 40 A (Total output current) Module for redundancy mode. Decoupling of two 5 A to 20 A power supplies or one 40 A power supply per redundancy module. Floating relay contact and green LED for signaling “Infeed 1 and 2 o.k.“, switching threshold adjustable between 20 to 25 V DC. 24 V DC 24…28.8 V DC Not applicable Not applicable 40 A Buffer module for mains buffering; connection by parallel switching at the output of the basic unit (6EP1x3x-3BA0x); buffer time 200 ms at 40 A to 1.6 s at 5 A load current; multiplication possible using parallel switching; maximum buffer time 10 s. 24 V DC 24…28.8 V DC 6EP1961-3BA01 Redundancy Redundancy module Mains buffering Buffer module 2) Efficiency at rated values, approx. – Setting range Signaling Technical data Power security components to increase system availability 26 Module for distributing the 24 V supply over up to four load circuits and their monitoring for overload; selective shutdown of faulty load circuits, rated current individually adjustable; universal use for all power supplies. Brief description of product/ function $179.00 US list price $200.00 CE, UL, cURus, cCSAus Class I Div 2, ATEX, GL (ABS pending) Certification Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) $179.00 0.2 kg Weight approx. $200.00 0…+ 60 °C 72 x 80 x 72 Dimensions (W x H x D) in mm $225.00 CE, UL, cURus, cCSAus Class I Div 2, ATEX 0.4 kg 72 x 90 x 90 IP20 Class B Yes No 2...10 A 97% 97% 4 x 10 A 3...10 A 4 x 10 A 0…+ 60 °C Class B Radio interference suppression (EN 55022) 0.5...3 A 4x3A Status indication via 2-color LED per channel; common reset via pushbutton, plug-in fuse per channel; status indication via 3-color LED per channel; common signaling contact. Ambient temperature Yes 3...10 A 4 x 10 A Individual load circuits can be switched on sequentially. Status indication via 3-color LED per channel; remote reset with 24 V signal and reset via pushbutton per channel; single channel signaling for channel-specific analysis via SIMATIC S7-function block. 24 V DC 22…30 V DC 6EP1961-2BA00 SITOP select diagnosis module Degree of protection (EN 60529) IP20 No Parallel switching Electronic short-circuit protection Efficiency at rated values, approx. 97% 4x3A 0.5...3 A Rated output current – Setting range Individual load circuits can be switched on sequentially. Status indication via 3-color LED per channel; remote reset with 24 V signal and reset via pushbutton per channel; common signaling contact. 6EP1961-2BA41 24 V DC 22…30 V DC 6EP1961-2BA31 Rated input voltage – Range 6EP1961-2BA21 6EP1961-2BA11 Order no. Monitoring SITOP PSE200U with single channel signaling SITOP PSE200U selectivity module new! SITOP Technical data Power security components to increase system availability 27 Class B IP20 Radio interference suppression (EN 55022) Degree of protection (EN 60529) Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change $210.00 $158.00 $835.00 $950.00 $335.00 $420.00 $420.00 $166.00 6.0 kg CE, cURus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T3 3.2 kg CE, cURus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T3 1.8 kg CE, cURus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T4 186 x 168 x 121 Wall mounting -10…+50 °C IP00 Yes 30 A/32 V Not applicable 30 A 1.1 kg 190 x 151 x 82 DIN rail -10…+50 °C IP00 Yes 15 A/32 V Not applicable 15 A Charging current max. 1.75 A CE, cULus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T4 96 x 106 x 108 DIN rail -10…+50 °C IP00 Yes Installed battery fuse 7.5 A/32 V Not applicable 6A 24 V DC, 22 to 27.0 V DC (No-load operation) Charging current 0.8 A 0.4 kg 102 x 125 x 125 DIN rail -25…+60 °C IP20 Class B No Buffer mode: 97 %, Standby mode: 97 % 40 A, Charging current: typ. 2 A Charging current max. 0.3 A CE, cULus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T3 50 x 125 x 125 DIN rail -25…+60 °C IP20 Class B No Buffer mode: 96 %, Standby mode: 96 % 15 A, Charging current: typ. 0.7 A 40 A + approx. 2.6 A with empty battery From 24 V/10 A Also available: high-temperature battery module 24 V/2.5 Ah (6EP1935-6MD31) for ambient temperature –40 to +60 °C and battery module 24 V/12 Ah (6EP1935-6MF01) $275.00 $335.00 $335.00 US list price 1) 0.4 kg CE, cULus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T4 Weight approx. Certification 50 x 125 x 125 No Switching in parallel Dimensions (W x H x D) in mm Electronic, automatic restart Overload and short-circuit protection -25…+60 °C Buffer mode: 94 %, Standby mode: 95 % Efficiency at rated values, approx. DIN rail 6 A, Charging current: typ. 0.4 A Rated output current Ambient temperature 24 V DC (Upstream SITOP device or battery), charging voltage: 27.0 V Rated output voltage Installation 6 A + approx. 0.85 A with empty battery Rated input current 15 A + approx. 1 A with empty battery 24 V DC, 22…29 V, Infeed from 24 V SITOP power supply: From 24 V/ 0.6 A From 24 V/5 A Input voltage 6EP1935-6ME21 DC UPS battery module 24 V/7 Ah1) Recomm. end-of-charge voltage: 26.4…27.3 V DC (> +20 °C), 27.3…29.0 V DC (< +20 °C) 6EP1935-6MD11 6EP1935-6MC01 6EP1931-2FC21 6EP1931-2EC21 6EP1931-2EC31 6EP1931-2EC42 6EP1931-2DC21 6EP1931-2DC31 6EP1931-2DC42 Order no. – with serial interface – with USB interface 6EP1931-2FC42 DC UPS battery module 24 V/3.2 Ah1) DC UPS battery module 24 V/1.2 Ah1) DC UPS module 24 V/40 A DC UPS module 24 V/15 A SITOP DC UPS, for longer power failures DC UPS module 24 V/6 A SITOP Output voltage/current Technical data Uninterruptible power supplies SITOP DC UPS with battery modules for bridging longer power failures 28 34.5 min. 15.5 min. 9 min. 6.5 min. 3.5 min. – – – – – – – – 1 A 2 A 3 A 4 A 6 A 8 A 10 A 12 A 14 A 16 A 20 A 25A 30A – – – – – – 9 min. 12.1 min. 17.5 min. 27.1 min. 39.3 min. 1h 2.6 h Battery module 3.2 Ah (6EP1935-6MD11) – – 9.1 min. 12.5 min. 15.1 min. 17.3 min. 21.8 min. 28.6 min. 41 min. 1.2 h 1.6 h 2.6 h 5.4 h Battery module 7 Ah (6EP1935-6ME21) Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 1) High temperature battery module for ambient temperature –40 to +60 °C Buffer time determination was based on the discharging time of new and completely charged battery modules with a minimum battery temperature of +25ºC until decrease of the battery voltage to 21 V (with voltage drops in the DC UPS, approx. 20.4 V DC remain for the load) Battery module 1.2 Ah (6EP1935-6MC01) Load current Selection table battery modules and buffer times 9.1 min. 12.6 min. 20.1 min. 23.8 min. 27.5 min. 33.3 min. 43.5 min. 53.3 min. 1.2 h 2.2 h 2.9 h 4.6 h 9h Battery module 12 Ah (6EP1935-6MF01) – – 4.3 min. 4.3 min. 5.1 min. 6.8 min. 8.8 min. 12.5 min. 17.6 min, 27 min. 37.5 min. 1h 2h Battery module1) 2.5 Ah (6EP1935-6MD31) 29 6EP1933-2EC41 Order no. DIN rail 120 x 125 x 125 1.0 kg CE, cULus, ATEX, GL, ABS, Hazardous Location Class I Div 2 Groups A, B, C, & D, T4 $630.00 Installation Dimensions (W x H x D) in mm Weight approx. Certification US list price $800.00 1.2 kg 120 x 125 x 125 DIN rail 0…+60 °C $545.00 0.7 kg 70 x 125 x 125 DIN rail 0…+60 °C IP20 Connector set with input and output connector as well as prepared USB cable in 2 m length: Order no. 6EP1975-2ES00 Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 1) 0…+60 °C Ambient temperature IP20 IP20 Yes, up to 3 units Class B Degree of protection (EN 60529) Class B Electronic, automatic restart Overload and short-circuit protection No 97.50 % Efficiency at rated values, approx. Class B 15 A, charging current 1 A (factory setting) or 2 A selectable Rated output current Switching in parallel In buffer mode and normal mode 24 V DC +/-3 % Rated output voltage Description: expansion module for extending the buffering time, up to 3 units can be switched in parallel with one UPS500S basic unit Infeed from basic unit 6EP1935-5PG01 Radio interference suppression (EN 55022) 24 V DC, 22…29 V, Infeed from SITOP 24 V 15.2 A + approx. 2.3 A in charging mode Input voltage Rated input current 6EP1933-2EC51 5 kWs UPS501 – Expansion module Maintenance-free DC UPS 5 kWs UPS500S – Basic unit 15 A 2.5 kWs SITOP Energy Technical data Uninterruptible power supplies – SITOP UPS500 maintenance-free DC UPS with capacitor technology 30 – 2.5 kWs Expansion modules Total energy 90 sec 75 sec 38 sec 26 sec 19 sec 15 sec 12 sec 10 sec 8 sec 6 sec 4 sec 3 sec 0.8 A 1 A 2 A 3 A 4 A 5 A 6 A 7 A 8 A 10 A 12 A 15 A 110 sec 1 A 205 sec 120 sec 9 sec 12 sec 15 sec 18 sec 21 sec 26 sec 31 sec 39 sec 52 sec 76 sec 138 sec 167 sec 236 sec 5 kWs – 5 kWs 311 sec 158 sec 14 sec 19 sec 23 sec 29 sec 34 sec 40 sec 49 sec 61 sec 82 sec 122 sec 219 sec 266 sec 390 sec 7.5 kWs 1 x 5 kWs 2.5 kWs 425 sec 223 sec 20 sec 26 sec 32 sec 40 sec 47 sec 55 sec 65 sec 81 sec 106 sec 156 sec 296 sec 346 sec 478 sec 10 kWs 1 x 5 kWs 5 kWs Specifications at rated input voltage and ambient temperature +25°C (unless otherwise specified) All prices are subject to change 54 sec 2 A Charging current Charging times 134 sec 0.5 A Load current Buffer times 2.5 kWs Basic unit SITOP UPS500S/501S configurations Buffer times and charging times SITOP UPS500 503 sec 263 sec 25 sec 32 sec 39 sec 50 sec 58 sec 67 sec 81 sec 101 sec 136 sec 203 sec 365 sec 440 sec 632 sec 12.5 kWs 2 x 5 kWs 2.5 kWs 625 sec 318 sec 30 sec 38 sec 47 sec 59 sec 69 sec 80 sec 95 sec 120 sec 159 sec 230 sec 414 sec 527 sec 748 sec 15 kWs 2 x 5 kWs 5 kWs 695 sec 355 sec 35 sec 44 sec 54 sec 69 sec 81 sec 94 sec 111 sec 139 sec 186 sec 265 sec 490 sec 580 sec 851 sec 17.5 kWs 3 x 5 kWs 2.5 kWs 816 sec 417 sec 40 sec 52 sec 62 sec 79 sec 82 sec 106 sec 130 sec 160 sec 213 sec 306 sec 572 sec 706 sec 1007 sec 20 kWs 3 x 5 kWs 5 kWs Notes Siemens Industry, Inc. 3333 Old Milton Parkway Alpharetta, GA 30005 1-800-241-4453 [email protected] www.usa.siemens.com/sitop Subject to change without prior notice Order No.: MSBR-SITOP-0813 All rights reserved Printed in USA © 2013 Siemens Industry, Inc. The information provided in this brochure contains descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract. Availability and technical specifications are subject to change without prior notice. Any product names mentioned may be trademarks or product designations of Siemens or their suppliers, whose use by third parties for their own purposes may infringe the rights of the trademark owners.