Data sheet 6EP3333-8SB00-0AY0 SITOP PSU8200 24 V/5 A STABILIZED POWER SUPPLY INPUT: 120/230 V AC OUTPUT: 24 V/5 A DC Technical specifications Product SITOP PSU8200 Power supply, type 24 V/5 A Input Input 1-phase AC Supply voltage 1 with AC Rated value 120 V Supply voltage 2 with AC Rated value 230 V ● Note Automatic range selection Input voltage 1 with AC 85 ... 132 V Input voltage 2 with AC 170 ... 264 V Wide-range input No Mains buffering at Iout rated, min. 35 ms; at Vin = 120/230 V Rated line frequency 50 ... 60 Hz Rated line range 47 ... 63 Hz Input current at rated input voltage 120 V Rated value 2.1 A Input current at rated input voltage 230 V Rated value 1.2 A Switch-on current limiting (+25 °C), max. 10 A I²t, max. 0.2 A²·s Built-in incoming fuse T 3.15 A (not accessible) 6EP3333-8SB00-0AY0 Page 1/4 24.04.2015 Changes preserved © Copyright Siemens AG Protection in the mains power input (IEC 898) Recommended miniature circuit breaker at 1-phase operation: from 6 A (10 A) characteristic C (B); required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2011-1EA10 (setting 3.8 A) or 3RV2711-1ED10 (UL 489) at 230 V; 3RV2011-1DA10 (setting 3 A) or 3RV2711-1DD10 (UL 489) at 400/500 V Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 3 % Static mains compensation, approx. 0.1 % Static load balancing, approx. 0.2 % Residual ripple peak-peak, max. 50 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 200 mV Adjustment range 24 ... 28.8 V Product function Output voltage adjustable Yes Output voltage setting via potentiometer; max. 120 W Status display Green LED for 24 V OK Signaling Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK" On/off behavior Overshoot of Vout approx. 3 % Startup delay, max. 1 s Voltage rise, typ. 30 ms Rated current value Iout rated 5 A Current range 0 ... 5 A ● Note As of Ua>24 V: 4% [Ia]/V [Ua]; at Ue<100 V/<200 V: 80% Ia rated Active power supplied typical 120 W Constant overload current on short-circuiting during the start-up typical 6 A Short-term overload current at short-circuit during operation typical 15 A Duration of overloading capability for excess current at short-circuit during operation 25 ms Parallel switching for enhanced performance Yes; switchable characteristic Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 93 % Power loss at Vout rated, Iout rated, approx. 9 W Active power loss during no-load operation maximum 1.5 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.1 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 2 % 6EP3333-8SB00-0AY0 Page 2/4 24.04.2015 Changes preserved © Copyright Siemens AG Load step setting time 50 to 100%, typ. 0.25 ms Load step setting time 100 to 50%, typ. 0.5 ms Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 2 % Load step setting time 10 to 90%, typ. 0.25 ms Load step setting time 90 to 10%, typ. 0.5 ms Setting time maximum 1 ms Protection and monitoring Output overvoltage protection < 33 V Current limitation, typ. 6 A Property of the output Short-circuit proof Yes Short-circuit protection Alternatively, constant current characteristic approx. 6 A or latching shutdown Enduring short circuit current RMS value typical 6 A Overcurrent overload capability in normal operation overload capability 150 % Iout rated up to 5 s/min Overload/short-circuit indicator LED yellow for "overload", LED red for "latching shutdown" Safety Primary/secondary isolation Yes Galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class I Leakage current maximum 3.5 mA Leakage current typical 1 mA CE mark Yes UL/CSA approval Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 Explosion protection ATEX (EX) II 3G Ex nA nC IIC T3 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T3 Certificate of suitability IECEx Yes Certificate of suitability NEC Class 2 No FM approval - CB approval Yes Marine approval GL, ABS Degree of protection (EN 60529) IP20 EMC Emitted interference EN 55022 Class B Supply harmonics limitation EN 61000-3-2 Noise immunity EN 61000-6-2 Operating data Ambient temperature during operation ● Note Ambient temperature during transport 6EP3333-8SB00-0AY0 Page 3/4 -25 ... +70 °C with natural convection -40 ... +85 °C 24.04.2015 Changes preserved © Copyright Siemens AG Ambient temperature during storage -40 ... +85 °C Humidity class according to EN 60721 Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections Supply input L, N, PE: 1 screw terminal each for 0.2 ... 2.5 mm² singlecore/finely stranded Connections Output +, -: 2 screw terminals each for 0.2 ... 2.5 mm² Connections Auxiliary 13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm²; 15, 16 (Remote): 1 screw terminal each for 0.14 ... 1.5 mm² Product function removable terminal at input No Product function removable terminal at output No Width of the enclosure 45 mm Height of the enclosure 125 mm Depth of the enclosure 125 mm Weight, approx. 0.8 kg Product property of the enclosure housing for sideby-side mounting Yes Installation Snaps onto DIN rail EN 60715 35x7.5/15 Electrical accessories Buffer module Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP3333-8SB00-0AY0 Page 4/4 24.04.2015 Changes preserved © Copyright Siemens AG