2PS13512E43W39689 Data Sheet (674 KB, EN)

TechnicalInformation
PrimeSTACK™
2PS13512E43W39689
Preliminarydata
Generalinformation
IGBTStackfortypicalvoltagesofupto400VRMS
Ratedoutputcurrent900ARMS
· Solar power
· Motor drives
· High power converter
· 62mm power module
· TrenchstopTM IGBT4
Topology
1/2 B2I
Application
Inverter
Load type
resitive, indutive
Semiconductor (Inverter
Section)
3x FF450R12KE4
Heatsink
water cooled
Implemented sensors
current, voltage, temperature
Driver signals IGBT
Electrical
Design standards
EN 50178
Approvals
UL 508C
Sales - name
2PS13512E43W39689
SP - No.
SP001132612
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
1
TechnicalInformation
PrimeSTACK™
2PS13512E43W39689
Preliminarydata
Absolutemaximumratedvalues
Collector-emitter voltage
IGBT; Tvj = 25°C
Repetitive peak reverse voltage Diode; Tvj = 25°C
VCES
1200
V
VRRM
1200
V
Insulation management
according to installation height of 2000 m
Vline
500
VRMS
Insulation test voltage
according to EN50178, f = 50 Hz, t = 1 s
VISOL
2.5
kVRMS
fsw2
8
kHz
Switching frequency inverter
section
Notes
Further maximum ratings are specified in the following dedicated sections
Characteristicvalues
DCLink
min.
Rated voltage
VDC
typ.
max.
650
850
typ.
max.
V
Notes
The over voltage shutdown level is above the max.rated DC voltage. Therefore this function can not be used
InverterSection
min.
Rated continuous current
VDC = 650 V, VAC = 400 VRMS, cos(ϕ) = 0.85,
fAC sine = 50 Hz, fsw = 5000 Hz, Tinlet = 40°C, Tj ≤ 125 °C
Continuous current at low
frequency
VDC = 650 V, cos(ϕ) = 0.85, fAC sine = 0 Hz, fsw = 5000 Hz,
Tinlet = 40 °C, Tj ≤ 125 °C
Rated continuous current for
150% overload capability
IAC 150% = 1080 ARMS, ton over = 60 s, trecovery = 600 s,
Tj ≤ 125 °C
Over current shutdown
Power losses
IAC
900
ARMS
IAC low
540
ARMS
IAC over1
720
ARMS
within 15 µs
IAC OC
1860
Apeak
IAC = 900 A, VDC = 650 V, VAC = 400 VRMS, cos(ϕ) = 0.85,
fAC sine = 50 Hz, fsw = 5000 Hz, Tinlet = 40 °C, Tj ≤ 125 °C
Ploss
2940
W
Notes
Maximum junction temperature limited to 125°C under all operating conditions
Controllerinterface
Driver and interface board
ref. to separate Application Note
DR240
Auxiliary voltage
Vaux
min.
typ.
max.
18
24
40
V
40
W
4
V
Auxiliary power requirement
Vaux = 24 V
Paux
Digital input level
resistor to GND 10 kΩ, capacitor to GND 1 nF
Vin low
0
Vin high
11
15
V
Digital output level
open collector, logic low = no fault, max. 15 mA
Vout low
0
1.5
V
Vout high
15
V
Analog current sensor output
inverter section
load max 5 mA, @ 900 ARMS
VIU ana2
VIV ana2
VIW ana2
Analog DC link voltage sensor
output
load max 5 mA, @ 800 V
VDC ana
Analog temperature sensor
output inverter section
(Simulated)
load max 5 mA, @TNTC = 55 °C,
corresponds to Tj = 125 °C at rated conditions
VTheta sim2
4.5
V
Over temperature shutdown
inverter section
@TNTC = 81 °C
VError OT2
10
V
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
2
4.8
4.9
5
V
5.5
5.7
5.8
V
TechnicalInformation
PrimeSTACK™
2PS13512E43W39689
Preliminarydata
Systemdata
EMC robustness
min.
according to IEC 61800-3 at named
interfaces
power
typ.
2
kV
control
VBurst
1
kV
aux (24V)
Vsurge
1
kV
Storage temperature
Operational ambient
temperature
PCB, DC link capacitor, bus bar, excluding cooling
medium
Cooling air velocity
PCB, DC link capacitor, bus bar, standard atmosphere
Humidity
no condensation
Vibration
Shock
Tstor
-40
80
°C
Top amb
-25
55
°C
Vair
0.3
Rel. F
0
m/s
85
%
according to IEC 60721
5
m/s²
according to IEC 60721
40
m/s²
120
mm
Protection degree
IP00
Pollution degree
Dimensions
2
width x depth x height
260
Weight
280
7.7
Heatsinkwatercooled
Water flow
max.
VBurst
min.
according to coolant specification from Infineon
∆V/∆t
typ.
kg
max.
10
dm³/min
Water pressure
30
Water pressure drop
∆p
Coolant inlet temperature
Tinlet
Cooling channel material
-40
bar
8
mbar
70
°C
Aluminium
Notes
Conditions are standard Infineon characterization for heatsinks.
Unit 1
Overviewofoptionalcomponents
Inverter
Section
Parallel interface board
Optical interface board
Chopper controller
Voltage sensor
×
Current sensor
×
Temperature sensor
×
DC link capacitors
Notes
Setting of Active Clamping TVS-Diodes: VZ = 824 V
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
3
Unit 3
TechnicalInformation
2PS13512E43W39689
PrimeSTACK™
Preliminarydata
fo - derating curve IGBT (motor), Diode (generator)
cos(phi) = ± 0,85
Tcool medium = 40°C
fsw - derating curve IGBT (motor), Diode (generator)
cos(phi) = ± 0,85
Tcool medium = 40°C
120
120
110
100
90
80
70
I/Inorm [%]
I/Inorm [%]
80
60
50
40
40
30
20
motor ; 100% = 900 A rms
generator ; 100% = 900 A rms
10
0
-5
0
5
motor ; 100% = 900 A rms
generator ; 100% = 900 A rms
0
1000
10 15 20 25 30 35 40 45 50 55
2000
3000
4000
f0 [Hz]
6000
7000
8000
Continuous current derating curves vs. Tcool medium
cos(phi) = ± 0,85
120
120
110
110
100
100
90
90
80
80
70
70
I/Inorm [%]
I/Inorm [%]
Continuous current derating curves vs. dc link voltage
cos(phi) = ± 0,85
Tcool medium = 40°C
60
50
60
50
40
40
30
30
20
20
motor ; 100% = 900 A rms
generator ; 100% = 900 A rms
10
0
400
5000
fsw [Hz]
450
500
550
600
650
700
motor ; 100% = 900 A rms
generator ; 100% = 900 A rms
10
750
800
0
850
Vdc [V]
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
40
45
50
55
Tcool medium [°C]
4
60
65
70
TechnicalInformation
2PS13512E43W39689
PrimeSTACK™
Preliminarydata
Zth heat sink to ambient per switch
0.080
Zth heat sink to ambient [K/W]
0.070
0.060
0.050
0.040
0.030
0.020
i:
1
2
3
4
ri[K/W]: 0.00002 0.03324 0.01822 0.00958
τi[s]:
0.9141 1.4372 3.9329 14.5531
0.010
0.000
0.1
1
10
100
1000
10000
time [s]
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
5
TechnicalInformation
PrimeSTACK™
2PS13512E43W39689
Preliminarydata
Mechanicaldrawing
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
6
TechnicalInformation
2PS13512E43W39689
PrimeSTACK™
Preliminarydata
Circuitdiagram
Circuit diagram
+
Input
VCE(sat) / supply
Fault
Output
X1:3
Over-Temp.
X1:22
Over-Voltage
X1:13
GND digital
X1:25
GND digital
TOP
A
BOT
-
Digital circuit
X1:2
EiceDRIVER™
IGBT plus
IGBT minus
Error messages
X1:15
X1:14
+
B
-
Error messages
+
X1:4 Supply DC plus
-
In
X1:6 Supply DC GND
X1:18 Supply DC GND
X1:5 +15V DC/50mA
Out
X1:17 +15V DC/50mA
ϑ
Power supply
X1:16 Supply DC plus
X1:20
C
PTC
Option DC link capacitors
+
Current
Output
Temperature
Mana
X1:21 Voltage DC-Link
X1:7
GND analog
X1:8
GND analog
X1:9
GND analog
-
Analog circuit
X1:19
High voltage
area in grey
Option V
Voltage measurement
reinforced isolation between
high voltage area and
low voltage area
NC
X1:11
NC
X1:12
NC
X1:23
NC
X1:24
NC
Error Table
Error outputs (open collector)
Error
Pin 2
SUB-D-Connector
25pole male
X1:1 True earth/shield
Temp.
Pin 3
Error Driver Core
X
Overcurrent
X
Overtemperature output stage
X
X
Overtemperature PCB
X
Overvoltage DC-Link (Option)
X
Undervoltage power supply
X
X= high level with required external pull up resistor.
female thread
UNC4/40
Voltage
Pin 22
X
X
1
front view
For detailed technical information please refer the PrimeSTACK manual.
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
7
2PS-C3-V-Rev04
X1:10
TechnicalInformation
PrimeSTACK™
2PS13512E43W39689
Preliminarydata
Terms&Conditionsofusage
Thedatacontainedinthisproductdatasheetisexclusivelyintendedfortechnicallytrainedstaff.Youandyourtechnical
departmentswillhavetoevaluatethesuitabilityoftheproductfortheintendedapplicationandthecompletenessoftheproduct
datawithrespecttosuchapplication.
Thisproductdatasheetisdescribingthecharacteristicsofthisproductforwhichawarrantyisgranted.Anysuchwarrantyis
grantedexclusivelypursuantthetermsandconditionsofthesupplyagreement.Therewillbenoguaranteeofanykindforthe
productanditscharacteristics.
Shouldyourequireproductinformationinexcessofthedatagiveninthisproductdatasheetorwhichconcernsthespecific
applicationofourproduct,pleasecontactthesalesoffice,whichisresponsibleforyou(seewww.infineon.com,sales&contact).
Forthosethatarespecificallyinterestedwemayprovideapplicationnotes.
Duetotechnicalrequirementsourproductmaycontaindangeroussubstances.Forinformationonthetypesinquestionplease
contactthesalesoffice,whichisresponsibleforyou.
ShouldyouintendtousetheProductinaviationapplications,inhealthorliveendangeringorlifesupportapplications,please
notify.Pleasenote,thatforanysuchapplicationsweurgentlyrecommend
-toperformjointRiskandQualityAssessments;
-theconclusionofQualityAgreements;
-toestablishjointmeasuresofanongoingproductsurvey,
andthatwemaymakedeliverydependedontherealization
ofanysuchmeasures.
Ifandtotheextentnecessary,pleaseforwardequivalentnoticestoyourcustomers.
Changesofthisproductdatasheetarereserved.
SafetyInstructions
Priortoinstallationandoperation,allsafetynoticesandwarningsandallwarningsignsattachedtotheequipmenthavetobe
carefullyread.Makesurethatallwarningsignsremaininalegibleconditionandthatmissingordamagedsignsarereplaced.To
installationandoperation,allsafetynoticesandwarningsandallwarningsignsattachedtotheequipmenthavetobecarefully
read.Makesurethatallwarningsignsremaininalegibleconditionandthatmissingordamagedsignsarereplaced.
preparedby:OW
dateofpublication:2014-07-16
approvedby:YZ
revision:2.0
8