EN

Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Features
–– Size ø58 mm
–– Precise optical sensing
–– Output signal level TTL or HTL
–– Clamping or synchro flange
–– Connection axial, radial or tangential
–– Pulses per revolution up to 5000
–– High protection up to IP 67
–– High resistance to shock and vibrations
Technical data - mechanical design
Voltage supply
Size (flange)
ø58 mm
Admitted shaft load
≤40 N axial
≤80 N radial
Protection DIN EN 60529
IP 65 (without shaft seal),
IP 67 (with shaft seal)
Operating speed
≤6000 rpm (+20 °C, IP 67)
≤12000 rpm (+20 °C, IP 65)
Starting torque
≤0.015 Nm (+20 °C, IP 65)
≤0.02 Nm (+20 °C, IP 67)
Materials
Housing: aluminium die-cast
Flange: aluminium
Solid shaft: stainless steel
Operating temperature
-40...+85 °C
Relative humidity
90 % non-condensing
Resistance
DIN EN 60068-2-6
Vibration 30 g, 10-2000 Hz
DIN EN 60068-2-27
Shock 300 g, 6 ms
Connection
Flange connector M12, 8-pin
Flange connector M23, 12-pin
Cable
Weight approx.
300 g
5 VDC ±5 %
8...30 VDC
4.75...30 VDC
Reverse polarity protection Yes
Short-circuit proof
Yes (HTL)
Yes (TTL, max. 1 s and 1 signal)
Consumption w/o load
≤70 mA
Pulses per revolution
100...5000
Phase shift
90° ±10°
Scan ratio
40...60 %
Reference signal
Zero pulse, width 90° ±10 %
Sensing method
Optical
Output frequency
≤300 kHz (TTL)
≤160 kHz (HTL)
Output signals
A+, B+, R+, A-, B-, R-
Output stages
TTL/RS422
HTL/push-pull
Interference immunity
DIN EN 61000-6-2
Emitted interference
DIN EN 61000-6-3
Approval
UL 508 / CSA 22.2
EIL580 - clamping flange
Shaft type
ø10 x 20 mm, solid shaft with
edge (clamping flange)
ø9.525 mm (3/8") x 20 mm,
solid shaft with edge
EIL580 - synchro flange
Shaft type
1
ø6 x 10 mm, solid shaft with flat
edge (synchro flange)
www.baumer.com/motion
7/1/2016
Technical data - electrical ratings
Subject to modification in technic and design. Errors and omissions excepted.
EIL580 with clamping flange
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Part number
Clamping flange
EIL580-S
C
.
.
.A
Pulse number - see table
E
H
N
Q
R
L
F
B
T
U
D
A
P
Q
Voltage supply / output stages
5 VDC, TTL/RS422, 6 channel
8...30 VDC, TTL/RS422, 6 channel
8...30 VDC, HTL/push-pull, 6 channel
4.75...30 VDC, HTL/push-pull, 6 channel
Connection
Cable radial, 1 m
Cable radial, 2 m
Flange connector M23, 12-pin, radial, male, ccw
Flange connector M12, 8-pin, radial, male, ccw
Cable axial, 1 m
Cable axial, 2 m
Flange connector M23, 12-pin, axial, male, ccw
Flange connector M12, 8-pin, axial, male, ccw
Cable tangential, 1 m
Cable tangential, 2 m
Protection
5 IP 65
7 IP 67
Printed in bold = standard items (up to the quantity of 10 will be supplied within 5 working days).
Pulse number
100
120
150
200
250
256
300
360
400
500
512
600
Stock items
720
800
900
1000
1024
1200
1250
1440
1500
1800
2000
2048
EIL580-SC10.5FE.01024.A
EIL580-SC10.5FN.01024.A
2500
3000
3600
4000
4096
5000
EIL580-SC10.5FE.02048.A
EIL580-SC10.5FN.02048.A
Numerous stock items in single quantity will be supplied
within 24 hours respectively one day ex works.
2
www.baumer.com/motion
7/1/2016
Flange
C Clamping flange, centering collar ø36 mm, M3/M4
Subject to modification in technic and design. Errors and omissions excepted.
Specification solid shaft
U3 ø9.525 mm (3/8”) x 20 mm, with edge
10 ø10 x 20 mm, with edge
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Part number
Synchro flange
EIL580-S
Y
06
.
.
.A
Pulse number - see table
E
H
N
Q
R
L
F
B
T
U
D
A
P
Q
Voltage supply / output stages
5 VDC, TTL/RS422, 6 channel
8...30 VDC, TTL/RS422, 6 channel
8...30 VDC, HTL/push-pull, 6 channel
4.75...30 VDC, HTL/push-pull, 6 channel
Connection
Cable radial, 1 m
Cable radial, 2 m
Flange connector M23, 12-pin, radial, male, ccw
Flange connector M12, 8-pin, radial, male, ccw
Cable axial, 1 m
Cable axial, 2 m
Flange connector M23, 12-pin, axial, male, ccw
Flange connector M12, 8-pin, axial, male, ccw
Cable tangential, 1 m
Cable tangential, 2 m
Protection
5 IP 65
7 IP 67
Printed in bold = standard items (up to the quantity of 10 will be supplied within 5 working days).
Pulse number
100
120
150
200
250
256
300
360
400
500
512
600
Stock items
720
800
900
1000
1024
1200
1250
1440
1500
1800
2000
2048
EIL580-SY06.5FE.01024.A
EIL580-SY06.5FN.01024.A
2500
3000
3600
4000
4096
5000
EIL580-SY06.5FE.02048.A
EIL580-SY06.5FN.02048.A
Numerous stock items in single quantity will be supplied
within 24 hours respectively one day ex works.
3
www.baumer.com/motion
7/1/2016
Flange
Y Synchro flange, flute ø53 mm, M3/M4
Subject to modification in technic and design. Errors and omissions excepted.
Specification solid shaft
06 ø6 x 10 mm, with edge
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Accessories
Accessories
Connectors and cables
Mounting accessories for EIL580 - clamping flange
10127844
11101893
Connection cable 2 m shielded with female
connector M12, 8-pin, straight (ESG
34FH0200G)
Tether arm
Mounting accessories for EIL580 - synchro flange
10129332
Connection cable 5 m shielded with female
connector M12, 8-pin, straight (ESG
34FH0500G)
11065916
Coupling CPS25 L=19 d1=06/d2=06
11065917
Coupling CPS25 L=19 d1=06/d2=08
10129333
Connection cable 10 m shielded with
female connector M12, 8-pin, straight (ESG
34FH1000G)
11065922
Coupling CPS25 L=19 d1=10/d2=06
11065926
Coupling CPS25 L=19 d1=11/d2=06
11065928
Coupling CPS25 L=19 d1=12/d2=06
11053961
Connection cable 2 m shielded with female
connector M12, 8-pin, angled (ESW
33FH0200G)
10141131
Spring washer coupling D1=06 / D2=06
10141132
Spring washer coupling D1=06 / D2=10
11053962
Connection cable 5 m shielded with female
connector M12, 8-pin, angled (ESW
33FH0500G)
11034139
Spring washer coupling D1=06 / D2=16
11050507
Bellows coupling aluminium/stainless steel
D1=06 / D2=10
10170054
Connection cable 10 m shielded with
female connector M12, 8-pin, angled (ESW
33FH1000G)
10117667
Mounting adaptor for encoders with synchro
flange
10117668
Set of eccentric fixings for mounting clamp
(10117667): 3x eccentric fixings, screws and
nuts
11065545
Set of eccentric fixings type A
10158124
Bearing flange for encoders with synchro
flange (Z 119.035)
10164705
Connector M23, 12-pin
11095302
Connection cable 1 m shielded with female
connector M23, 12-pin
11100408
Connection cable 2 m shielded with female
connector M23, 12-pin
11100430
Connection cable 5 m shielded with female
connector M23, 12-pin
11100431
Connection cable 10 m shielded with female
connector M23, 12-pin
Matching measuring wheels available as accessories, see
under “measuring wheels” (MR).
Coupling CPS25 L=19 d1=04/d2=10
11065918
Coupling CPS25 L=19 d1=07/d2=10
11065920
Coupling CPS25 L=19 d1=08/d2=10
11065921
Coupling CPS25 L=19 d1=09/d2=10
11065922
Coupling CPS25 L=19 d1=10/d2=06
11065923
Coupling CPS25 L=19 d1=10/d2=10
11065924
Coupling CPS25 L=19 d1=10/d2=11
11065925
Coupling CPS25 L=19 d1=10/d2=12
10141132
Spring washer coupling D1=06 / D2=10
10141133
Spring washer coupling D1=10 / D2=10
11034138
Spring washer coupling D1=10 / D2=16
11034140
Spring washer coupling D1=10 / D2=14
11034141
Spring washer coupling D1=10 / D2=12
11050507
Bellows coupling aluminium/stainless steel
D1=06 / D2=10
11101781
Double loops coupling D1=10 / D2=10
10125051
Mounting adaptor for encoders with clamping
flange
11065545
Set of eccentric fixings type A
4
www.baumer.com/motion
7/1/2016
11065915
Subject to modification in technic and design. Errors and omissions excepted.
Mounting accessories for EIL580 - clamping flange
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Output signals
Terminal assignment
&ORFNZLVHURWDWLQJGLUHFWLRQZKHQORRNLQJDWIODQJH
Flange connector M23, 12-pin / cable
Pin
Core color
Assignment
$
1
pink
B-
2
–
–
$
3
blue
R+
4
red
R-
5
green
A+
6
yellow
A-
7
–
–
8
grey
B+
9
–
–
10
white
GND
11
–
–
12
brown
UB
%
%
ƒ
5
5
Screen:
Connected to housing
Cable data: PVC, [4x2x0.14 mm2], bending radius
>32.5 mm, outer diameter 6.5 mm
Trigger level
Outputs
TTL/RS422
Output level High
≥2.5 V
2 10
Output level Low
≤0.5 V
3
Load
≤20 mA
Outputs
HTL/Push-pull
Output level High
≥UB -3 V
Output level Low
≤1.5 V
Load
≤20 mA
1
4
9
8
12
7
6
11
5
Assignment
1
GND
2
UB
3
A+
4
A-
5
B+
6
B-
7
R+
8
R7
1
2
3
5
6
8
5
4
www.baumer.com/motion
7/1/2016
Pin
Subject to modification in technic and design. Errors and omissions excepted.
Flange connector M12, 8-pin
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Dimensions
Clamping flange, flange connector M12, radial
10 20
15
38
20°
7
ø48±0.2
11.8
a
ø9.525
8.64
ø10
9.
d g7
x
M3
51.4
a
°
(3x) 1
20
ø36h8
ø53±0.05
ø58
)1
20°
(3x
M4x7
d g7
3 3
M12x1
Clamping flange, flange connector M23, radial
38
3
10 20
3 15
ø48±0.2
ø36h8
ø53±0.05
ø58
a
ø9.525
8.64
ø10
9.
d g7
a
ø9.525
8.64
ø10
9.
d g7
7
M3x
56
a
°
(3x) 12
20
0°
)1
(3x
M4x7
d g7
14.3
M23x1
38
20°
10 20
15
3
3
ø36h8
ø53±0.05
ø58
d g7
x7
M3
ø48±0.2
~53
a
°
20
(3x) 12
0°
)1
(3x
M4x7
Subject to modification in technic and design. Errors and omissions excepted.
Clamping flange, cable radial
11.8
6
www.baumer.com/motion
7/1/2016
20°
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Dimensions
Clamping flange, flange connector M12, axial
10 20
15
38
21.8
20°
d g7
a
ø9.525
8.64
ø10
9.
x
M3
3
3
7
ø48±0.2
11.1
ø36h8
ø53±0.05
ø58
d g7
a
M12x1
°
(3x) 12
20
0°
)1
(3x
M4x7
Clamping flange, flange connector M23, axial
ø9.525
8.64
ø10
9.
M3
3
x7
ø48±0.2
d g7
a
°
20
M4x7
8.5
)1
0°
(3x
(3x) 12
10 20
15
M23x1
20°
38
a
ø36h8
ø53±0.05
ø58
26.5
d g7
3
10 20
15
7
M3x
ø48±0.2
3
3
ø36h8
ø53±0.05
ø58
d g7
a
°
20
(3x) 12
0°
)1
(3x
M4x7
7
d g7
a
ø9.525
8.64
ø10
9.
www.baumer.com/motion
7/1/2016
38
11.1
~23
20°
Subject to modification in technic and design. Errors and omissions excepted.
Clamping flange, cable axial
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Dimensions
Clamping flange, cable tangential
10 20
15
38.5
20°
a
ø36h8
ø53±0.05
ø58
0°
°
ø9.525
8.64
ø10
9.
19
.5
d g7
7
5
a
°
20
(3x) 12
)1
M3x
ø48±0.2
3
3
128
(3x
M4x7
d g7
Synchro flange, flange connector M12, radial
44
4
20°
10
9.
M3x
ø6h7
ø50h8
ø53±0.05
ø58
51.4
5.5
°
(3x) 12
20
0°
)1
(3x
x7
M4
7
3
ø42±0.2
3
M12x1
11.8
4
20°
x7
M3
x7
M4
ø42±0.2
56
5.5
°
20
ø6h7
ø50h8
ø53±0.05
ø58
°
)1
(3x
(3x) 12
0
10
9.
14.4
M23x1
8
www.baumer.com/motion
7/1/2016
44
Subject to modification in technic and design. Errors and omissions excepted.
Synchro flange, flange connector M23, radial
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Dimensions
Synchro flange, cable radial
44
4
10
9.
20°
ø6h7
ø50h8
ø53±0.05
ø58
20
(3x) 12
)1
0°
(3x
x7
M3
~53
5.5
°
x7
M4
ø42±0.2
3
3
11.8
Synchro flange, flange connector M12, axial
21.9
44
4
20°
M3
3
x7
ø42±0.2
11.1
5.5
ø6h7
ø50h8
ø53±0.05
ø58
M12x1
°
20
(3x) 12
)1
0°
(3x
x7
M4
10
9.
3
x7
M3
ø42±0.2
3
3
9
www.baumer.com/motion
7/1/2016
5.5
°
20
(3x) 12
0°
)1
(3x
x7
M4
10
9.
M23x1
20°
8.5
4
44
ø6h7
ø50h8
ø53±0.05
ø58
26.4
Subject to modification in technic and design. Errors and omissions excepted.
Synchro flange, flange connector M23, axial
Incremental encoders
Solid shaft with clamping or synchro flange
100…5000 pulses per revolution
EIL580 - solid shaft - OptoPulse®
Dimensions
Synchro flange, cable axial
~23
44
4
10
9.
20°
x7
3
11.1
5.5
°
M3
ø42±0.2
ø6h7
ø50h8
ø53±0.05
ø58
20
(3x) 12
)1
0°
(3x
x7
M4
3
Synchro flange, cable tangential
44.5
4
20°
10
9.
ø6h7
ø50h8
ø53-0.05
ø58
19
.5
Subject to modification in technic and design. Errors and omissions excepted.
3
10
www.baumer.com/motion
7/1/2016
(3x) 12
5.5
5
°
°
20
7
M3x
ø42±0.2
3
128
)1
0°
(3x
x7
M4