T2526 - Complete

T2526
Low-voltage IR Receiver ASSP
DATASHEET
Features
● No external components except PIN diode
● Supply-voltage range: 2.7V to 5.5V
● Highest sensitivity due to automatic sensitivity adaption (AGC) and automatic
strong signal adaption (ATC)
● Automatic supply voltage adaptation
● Highest immunity against disturbances from daylight and lamps
● Available for carrier frequencies between 30kHz to 56kHz; adjusted by zener-diode
fusing ±2.5%
● TTL and CMOS compatible
Applications
● Home entertainment applications (audio/video)
● Home appliances
● Remote control equipment
4597J-AUTO-04/14
1.
Description
The Atmel® IC T2526 is a complete IR receiver for data communication developed and optimized for use in carrierfrequency-modulated transmission applications. The IC offers highest sensitivity as well as highest suppression of noise
from daylight and lamps. The Atmel T2526 is available with broadest range of frequencies (30, 33, 36, 37, 38, 40, 44, 56kHz)
and 3 different noise suppression regulation types (standard, lamp, short burst) covering requirements of high-end remote
control solutions (please refer to selection guide available for Atmel T2525/T2526). Atmel The T2526 operates in a supply
voltage range of 2.7V to 5.5V.
The function of the Atmel T2526 can be described using the block diagram of Figure 1-1 on page 2. The input stage meets
two main functions. First it provides a suitable bias voltage for the PIN diode. Secondly the pulsed photo-current signals are
transformed into a voltage by a special circuit which is optimized for low noise applications. After amplification by a controlled
gain amplifier (CGA) the signals have to pass a tuned integrated narrow bandpass filter with a center frequency f0 which is
equivalent to the chosen carrier frequency of the input signal The demodulator is used first to convert the input burst signal to
a digital envelope output pulse and to evaluate the signal information quality, i.e., unwanted pulses will be suppressed at the
output pin. All this is done by means of an integrated dynamic feedback circuit which varies the gain as a function of the
present environmental conditions (ambient light, modulated lamps etc.). Other special features are used to adapt to the
current application to secure best transmission quality.
Figure 1-1. Block Diagram
VS
IN
Input
CGA and
filter
OUT
Demodulator
AGC/ATC
and digital control
Oscillator
Carrier frequency f0
T2526
Modulated IR signal
min 6 or 10 pulses
2.
Pin Description
Table 2-1.
Pin Description
Symbol
VS
OUT
IN
GND
2
GND
T2526 [DATASHEET]
4597J–AUTO–04/14
Function
Supply voltage
Data output
Input PIN-diode
Ground
Microcontroller
3.
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameter
Supply voltage
Supply current
Symbol
Value
Unit
VS
–0.3 to +6
V
IS
3
mA
Input voltage
VIN
–0.3 to VS
V
Input DC current at VS = 5V
IIN
0.75
mA
Output voltage
VO
–0.3 to VS
V
Output current
IO
10
mA
Operating temperature
Tamb
–25 to +85
°C
Storage temperature
Tstg
–40 to +125
°C
Power dissipation at Tamb = 25°C
Ptot
30
mW
4.
Electrical Characteristics, 3-V Operation
Tamb = 25°C, VS = 3V unless otherwise specified.
No.
1
Parameters
Symbol
Min.
Typ.
Max.
Supply-voltage range
1.2
Supply current
IIN =0
VS
2.7
3.0
IS
0.7
0.9
Type*
3.3
V
C
1.3
mA
B
k
A
250
mV
B
Vs
V
B
mA
B
µA
C
Output
2.1
Internal pull-up resistor(1)
Tamb = 25°C
See Figure 6-10 on page 9
RPU
2.2
Output voltage low
R2 = 2.4 k
See Figure 6-10 on page 9
VOL
2.3
Output voltage high
2.4
Output current clamping
3
Unit
Supply
1.1
2
Test Conditions
VOH
R2 = 0
See Figure 6-10 on page 9
IOCL
30/40
VS – 0.25
8
Input
3.1
Input DC current
VIN = 0
See Figure 6-10 on page 9
IIN_DCMAX
3.2
Input DC current
See Figure 6-3 on page 6
VIN = 0; Vs = 3V
Tamb = 25°C
IIN_DCMAX
–350
µA
B
3.3
Minimum detection
threshold current
See Figure 6-1 on page 6
IEemin
–700
pA
B
3.4
Minimum detection
threshold current with AC
current disturbance
IIN_AC100 =
3µA at 100Hz
Test signal:
See Figure 6-9 on page 9
VS = 3V
Tamb= 25°C, IIN_DC=1µA
square pp
burst N = 16
f = f0; tPER = 10ms
Figure 6-8 on page 8
BER = 50(2)
IEemin
–1300
pA
C
–150
*) Type means: A =100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1.
Depending on version, see “Ordering Information”
2.
BER = bit error rate; e.g., BER = 5% means that with P = 20 at the input pin 19...21 pulses can appear at the pin OUT
3.
After transformation of input current into voltage
T2526 [DATASHEET]
4597J–AUTO–04/14
3
4.
Electrical Characteristics, 3-V Operation (Continued)
Tamb = 25°C, VS = 3V unless otherwise specified.
No.
3.5
4
Parameters
Test Conditions
Maximum detection
threshold current with
VIN > 0V
Test signal:
See Figure 6-9 on page 9
VS = 3V, Tamb = 25°C
IIN_DC = 1µA
square pp
burst N = 16
f = f0; tPER = 10ms
Figure 6-8 on page 8
BER = 5%(2)
Symbol
Min.
IEemax
–200
Typ.
Max.
Unit
Type*
µA
D
Controlled Amplifier and Filter
4.1
Maximum value of variable
gain (CGA)
GVARMAX
51
dB
D
4.2
Minimum value of variable
gain (CGA)
GVARMIN
–5
dB
D
4.3
Total internal
amplification(3)
GMAX
71
dB
D
4.4
Center frequency fusing
accuracy of bandpass
4.5
Overall accuracy center
frequency of bandpass
4.6
Overall accuracy center
frequency of bandpass
Tamb = 0 to 70°C
4.7
BPF bandwidth
–3dB; f0 = 38kHz;
See Figure 6-7 on page 8
VS = 3V, Tamb = 25°C
f03V_FUSE
–2.5
f0
+2.5
%
A
f03V
–5.5
f0
+3.5
%
C
f03V
–4.5
f0
+3.0
%
C
kHz
C
B
3.8
*) Type means: A =100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
5.
1.
Depending on version, see “Ordering Information”
2.
BER = bit error rate; e.g., BER = 5% means that with P = 20 at the input pin 19...21 pulses can appear at the pin OUT
3.
After transformation of input current into voltage
Electrical Characteristics, 5-V Operation
Tamb = 25°C, VS = 5V unless otherwise specified.
No.
5
Parameters
Symbol
Min.
Typ.
Max.
Unit
Type*
VS
4.5
5.0
5.5
V
C
IS
0.9
1.2
1.6
mA
B
k
A
250
mV
B
Vs
V
B
Supply
5.1
Supply-voltage range
5.2
Supply current
6
Test Conditions
IIN =0
Output
6.1
Internal pull-up resistor(1)
Tamb = 25°C
See Figure 6-10 on page 9
RPU
6.2
Output voltage low
R2 = 2.4 k
See Figure 6-10 on page 9
VOL
6.3
Output voltage high
VOH
30/40
VS – 0.25
*) Type means: A =100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
4
1.
Depending on version, see “Ordering Information”
2.
BER = bit error rate; e.g., BER = 5% means that with P = 20 at the input pin 19...21 pulses can appear at the pin OUT
3.
After transformation of input current into voltage
T2526 [DATASHEET]
4597J–AUTO–04/14
5.
Electrical Characteristics, 5-V Operation (Continued)
Tamb = 25°C, VS = 5V unless otherwise specified.
No.
Parameters
Test Conditions
6.4
Output current clamping
R2 = 0
See Figure 6-10 on page 9
IOCL
VIN = 0
See Figure 6-10 on page 9
IIN_DCMAX
7
Input DC current
7.2
Input DC-current
VIN = 0; Vs = 5V
See Figure 6-4 on page 7 Tamb = 25°C
7.4
7.5
8
Min.
Typ.
8
Max.
Unit
Type*
mA
B
µA
C
Input
7.1
7.3
Symbol
Min. detection threshold Test signal:
current
See Figure 6-9 on page 9
See Figure 6-2 on page 6 VS = 5V
Tamb = 25°C
IIN_DC = 1µA
Min. detection threshold square pp
current with AC current burst N = 16
disturbance IIN_AC100 = f = f ; t
0 PER = 10ms
3 µA at 100 Hz
Figure 6-8 on page 8
BER = 50(2)
Test signal:
See Figure 6-9 on page 9
VS = 5V, Tamb = 25C,
I
= 1µA
Max. detection threshold IN_DC
square pp
current with VIN > 0V
burst N = 16
f = f0; tPER = 10ms
Figure 6-8 on page 8
BER = 5%(2)
–400
IIN_DCMAX
–700
µA
B
IEemin
–850
pA
B
IEemin
–2000
pA
C
µA
D
IEemax
–500
Controlled Amplifier and Filter
8.1
Maximum value of
variable gain (CGA)
GVARMAX
51
dB
D
8.2
Minimum value of
variable gain (CGA)
GVARMIN
–5
dB
D
8.3
Total internal
amplification(3)
GMAX
71
dB
D
8.4
Resulting center
frequency fusing
accuracy
f05V
f03V-FUSE
+ 0.5
%
A
f0 fused at VS = 3V
VS = 5V, Tamb = 25°C
*) Type means: A =100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
5.1
1.
Depending on version, see “Ordering Information”
2.
BER = bit error rate; e.g., BER = 5% means that with P = 20 at the input pin 19...21 pulses can appear at the pin OUT
3.
After transformation of input current into voltage
ESD
All pins  2000V HBM; 200V MM, MIL-STD-883C, Method 3015.7
5.2
Reliability
Electrical qualification (1000h) in molded plastic package
T2526 [DATASHEET]
4597J–AUTO–04/14
5
6.
Typical Electrical Curves at Tamb = 25°C
Figure 6-1. IEemin versus IIN_DC, VS = 3V
100
IEemin (nA)
VS = 3V
f = f0
10
1
0.1
0.1
1
10
100
1000
100
1000
IIN_DC (µA)
Figure 6-2. IEemin versus IIN_DC, VS = 5V
100
IEemin (nA)
VS = 5V
f = f0
10
1
0.1
0.1
1
10
IIN_DC (µA)
Figure 6-3. VIN versus IIN_DC, VS = 3V
3.5
VS = 3V
f = f0
3.0
VIN (V)
2.5
2.0
1.5
1.0
0.5
0
0
0.1
1
10
IIN_DC (µA)
6
T2526 [DATASHEET]
4597J–AUTO–04/14
100
1000
Figure 6-4. VIN versus IIN_DC, VS = 5V
3.5
VS = 5V
f = f0
3.0
VIN (V)
2.5
2.0
1.5
1.0
0.5
0
0
0.1
1
10
100
1000
IIN_DC (µA)
Figure 6-5. Data Transmission Rate, VS = 3V
50 0 0
4 50 0
VS = 3V
4000
Short burst
3 50 0
Bits/s
3000
2 50 0
Standard type
2000
Lamp type
150 0
10 0 0
50 0
0
25
35
45
55
65
f0 (kHz)
Figure 6-6. Data Transmission Rate, VS = 5V
50 0 0
4 50 0
VS = 5V
4000
Short burst
Bits/s
3 50 0
3000
Standard type
2 50 0
2000
150 0
Lamp type
10 0 0
50 0
0
25
35
45
55
65
f0 (kHz)
T2526 [DATASHEET]
4597J–AUTO–04/14
7
Figure 6-7. Typical Bandpass Curve
1.1
V S = 3V
Relative Amplitude
1.0
0.9
0.8
Bandwidth (-3dB)
0.7
0.6
0.5
0.4
0.92
0.94
0.96
0.98
1.00
1.02
1.04
1.06
1.08
f/f0
Q = f/f0/B; B => –3dB values.
Example: Q = 1/(1.047 – 0.954) = 11
Figure 6-8. Illustration of Used Terms
Example: f = 30kHz, burst with 16 pulses, 16 periods
1066μs
533μs
Period (P = 16)
Burst (N = 16 pulses)
IN
1
7
16
7
7
33μs
OUT
tDON
tDOFF
533μs
Envelope 1
Envelope 16
17056μs/data word
OUT
Telegram pause
Data word
Data word
t
17ms
TREF = 62ms
8
T2526 [DATASHEET]
4597J–AUTO–04/14
Figure 6-9. Test Circuit
IEe = ΔU1/400kΩ
VDD = 3V to 5V
ΔU1
400kΩ
1nF
R1 = 220Ω
IIN_DC
VS
IIN
20kΩ
IEe
IN
T2526
1nF
VPULSE
OUT
GND
ΔU2
C1
IIN_DC = ΔU2/40kΩ
20kΩ
f0
+
4.7μF
16
-
IIN_AC100
DC
+
t PER = 10ms
Figure 6-10. Application Circuit
(1)
VDD = 3V to 5V
optional
R 2(1) > 2.4kΩ
R 1 = 220Ω
RPU
IS
VS
IN
IIN
T2526
IOCL
IL
OUT
Microcontroller
GND
+
IIN_DC
IEe
C 1 = 4.7μF
VIN
VO
C 2(1) = 470pF
T2526 [DATASHEET]
4597J–AUTO–04/14
9
7.
Chip Dimensions
Figure 7-1. Chip Size in µm
1210,1040
GND
IN
336,906
783,887
scribe
length
VS
55,652
55,62
T2526
Fusing
OUT
0,0
width
Note:
Pad coordinates are given for lower left corner of the pad in µm from the origin 0,0
Dimensions
Pad metallurgy
Finish
Note:
10
1.
Length inclusive scribe
1.16mm
Width inclusive scribe
1.37mm
Thickness
290µ ±5%
Pads
90µ  90µ
Fusing pads
70µ  70µ
Material
AlCu/AlSiTi(1)
Thickness
0.8µm
Material
Si3N4/SiO2
Thickness
0.7/0.3µm
Value depends on manufacture location.
T2526 [DATASHEET]
4597J–AUTO–04/14
8.
Ordering Information
Delivery: unsawn wafers (DDW) in box
Extended Type Number
PL(2)
RPU(3)
D(4)
T2526S0xx(1)C-DDW
2
30
2179
T2526S1xx C-DDW
1
30
2179
T2526S2xx(1)C-DDW
2
40
1404
T2526S3xx C-DDW
1
40
1404
T2526S6xx(1)C-DDW
2
30
3415
1
30
3415
(1)
(1)
(1)
T2526S7xx C-DDW
Notes:
Type(5)
Standard type: ≥ 10 pulses, enhanced sensibility, high data rate
Lamp type: ≥ 10 pulses, enhanced suppression of disturbances,
secure data transmission
Short burst type: ≥ 6 pulses, enhanced data rate
1. xx means the used carrier frequency value f0 30, 33, 36, 38, 40, 44 or 56kHz
2. Two pad layout versions (see Figure 8-1 and Figure 8-2) available for different assembly demand
3. Integrated pull-up resistor at pin OUT (see electrical characteristics)
4. Typical data transmission rate up to bit/s with f0 = 56kHz, VS = 5V (see Figure 6-8 on page 8)
5. On request: noise type, data rate type
8.1
Pad Layout
Figure 8-1. Pad Layout 1
GND
IN
OUT
T2526
Fusing
VS
Figure 8-2. Pad Layout 2
(6)
(5)
GND
IN
(1)
VS
T2526
(3)
OUT
Fusing
T2526 [DATASHEET]
4597J–AUTO–04/14
11
9.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
History
4597J-AUTO-04/04
 Put datasheet in the latest template
 Features on page 1 changed
 Section 1 “Description” on page 1 changed
 Section 2 “Pin Description” on page 3 changed
4597I-AUTO-05/10
 Section 4 “Thermal Resistance” on page 3 deleted
 Section 4 “Electrical Characteristics, 3-V Operation” on pages 4 to 5 changed
 Section 5“Electrical Characteristics, 5-V Operation” on pages 5 to 6 changed
 Figure 6-5 “Data Transmission Rate, VS = 3V” on page 8 changed
 Figure 6-6 “Data Transmission Rate, VS = 5V” on page 8 changed
4597H-AUTO-09/09
 Put datasheet in the latest template
 Ordering Information table changed
 Features on page 1 changed
 Applications on page 1 changed
 Section 1 “Description” on page 1 changed
4597G-AUTO-10/06
 Section 5 “Electrical Characteristics, 3-V Operation” number 3.4 on page 3 changed
 Section 6 “Electrical Characteristics, 5-V Operation” number 7.3 and 7.4 on page 5
changed
 Section 9 “Ordering Information” on page 11 changed
4597F-AUTO-04/06
4597E-AUTO-04/06
 Section 9 “Ordering Information” on page 11 changed
 Put datasheet in the latest template
 Section 8 “Chip Dimensions” on page 10 changed
 Put datasheet in the latest template
4597D-AUTO-08/05
 First page: Pb-free logo added
Page 11: Ordering Information changed
 Page 2, 3, 5, 11, 13: SO8 deleted
12
T2526 [DATASHEET]
4597J–AUTO–04/14
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2014 Atmel Corporation. / Rev.: 4597J–AUTO–04/14
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or its
subsidiaries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.