+: 62 1 BGU8053 Low noise high linearity amplifier Rev. 3 — 18 April 2016 Product data sheet 1. General description The BGU8053 is a low noise high linearity amplifier for wireless infrastructure applications, equipped with fast shutdown to support TDD systems. The LNA has a high input and output return loss and is designed to operate between 2 GHz and 6 GHz. It is housed in a 2 mm 2 mm 0.75 mm 8-terminal plastic thin small outline package. The LNA is ESD protected on all terminals. 2. Features and benefits Low noise performance: NF = 0.56 dB High linearity performance: IP3O = 36 dBm High input return loss > 12 dB High output return loss > 20 dB Unconditionally stable up to 20 GHz Programmable bias current (via resistor) Small 8-terminal leadless package 2 mm 2 mm 0.75 mm ESD protection on all terminals Moisture sensitivity level 1 Fast shut down to support TDD systems 3 V to 5 V single supply 3. Applications Wireless infrastructure Low noise and high linearity applications LTE, W-CDMA, CDMA, GSM General-purpose wireless applications TDD or FDD systems Suitable for small cells BGU8053 NXP Semiconductors Low noise high linearity amplifier 4. Quick reference data Table 1. Quick reference data f = 2500 MHz; VCC = 5 V; Tamb = 25 C; input and output 50 ; R~bias = 5.1 k; unless otherwise specified. All RF parameters are measured in an application board as shown in Figure 16 with components listed in Table 9 optimized for f = 2500 MHz. Symbol Parameter Conditions Min Typ ICC supply current on state 36 48 60 mA off state - 2.8 - mA on state 17 18.5 20 dB - 23.5 - dB - 0.56 - 18 - dBm 32 36 - dBm Gass associated gain NF noise figure PL(1dB) output power at 1 dB gain compression IP3O output third-order intercept point off state [1] [1] 2-tone; tone spacing = 1 MHz; Pi = 15 dBm per tone Max Unit 0.75 dB Connector and Printed-Circuit Board (PCB) losses have been de-embedded. 5. Ordering information Table 2. Ordering information Type number BGU8053 Package Name Description Version HWSON8 plastic thermal enhanced very very thin small outline package; no leads; 8 terminals; body 2 2 0.75 mm SOT1327-1 6. Block diagram 9%,$6 QF %,$6 5),1 QF LF 5)287 6+'1 LF DDD Fig 1. BGU8053 Product data sheet Block diagram All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 2 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 7. Pinning information 7.1 Pinning WHUPLQDO LQGH[DUHD 9%,$6 LF 5)B,1 5)B287 QF 6+'1 LF LF DDD 7UDQVSDUHQWWRSYLHZ Fig 2. Pin configuration 7.2 Pin description Table 3. Symbol Pin description Pin Description VBIAS 1 bias voltage RF_IN 2 RF input n.c. 3 not connected i.c. 4, 5, 8 internally connected. Can be grounded or left open in the application SHDN 6 shutdown RF_OUT 7 RF output GND exposed die pad ground BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 3 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min VCC supply voltage - Max Unit 6 V Vctrl(sd) shutdown control voltage - 3 V ICC supply current - 85 mA Pi(RF)CW continuous waveform RF input power - 20 dBm Tstg storage temperature 40 +150 C - 150 C - 510 mW Human Body Model (HBM) According to ANSI/ESDA/JEDEC standard JS-001-2010 - 0.9 kV Charged Device Model (CDM); According to JEDEC standard 22-C101B - 2 kV Tj junction temperature P power dissipation Tcase 125 C VESD electrostatic discharge voltage [1] [1] Case is ground solder pad. 9. Recommended operating conditions Table 5. Characteristics Symbol Parameter VCC supply voltage Z0 characteristic impedance Tcase case temperature Conditions Min Typ Max Unit 4.75 5 - 50 - 40 - +85 C 5.25 V 10. Thermal characteristics Table 6. Thermal characteristics Symbol Parameter Rth(j-case) thermal resistance from junction to case Conditions [1][2] Typ Unit 50 K/W [1] Case is ground solder pad. [2] Thermal resistance measured using infrared measurement technique, device mounted on application board and placed in still air. BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 4 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 11. Characteristics Table 7. Characteristics f = 1900 MHz; VCC = 5 V; Tamb = 25 C; input and output 50 ; Rbias = 5.1 k; unless otherwise specified. All RF parameters are measured in an application board as shown in Figure 16 with components listed in Table 9 optimized for f = 1900 MHz. Symbol Parameter Conditions Min Typ Max Unit ICC supply current on state 36 48 60 mA off state - 2.8 - mA on state 17 18.5 20 dB - 23 - dB - 0.50 0.70 dB Gass associated gain NF noise figure PL(1dB) output power at 1 dB gain compression IP3O output third-order intercept point off state [1] - 18 - dBm 32 36 - dBm 30 34 - dBm on state - 14.5 - dB off state - 8.4 - dB - 23 - dB 2-tone; tone spacing = 1 MHz; Pi = 15 dBm per tone [2] 2-tone; tone spacing = 1 MHz; Pi = 15 dBm per tone RLin input return loss RLout output return loss ISL isolation ts(pon) power-on settling time Pi = 20 dBm; SHDN (pin 6) from HIGH to LOW [2] ts(poff) power-off settling time Pi = 20 dBm; SHDN (pin 6) from LOW to HIGH [2] K Rollett stability factor both on state and off state up to f = 20 GHz Rpd(SHDN) pull-down resistance on pin SHDN [1] Connector and Printed-Circuit Board (PCB) losses have been de-embedded. [2] For TDD systems where fast switching is required, the value of C1 and C2 should be changed to 100 pF. - 23 - dB - 1.4 - s - 0.4 - s 1 - - - 20 - k Table 8. Shutdown control VCC = 5 V; Tamb = 25 C. State Vctrl(sd) [1] Unit on state 0.6 V off state 1.2 V [1] Voltage on pin 6 (SHDN). BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 5 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 11.1 Graphics DDD DDD *S G% *S G% I*+] I*+] VCC = 5 V; Tamb = 25 C. VCC = 5 V; ICC = 48 mA. (1) Tamb = 40 C (1) ICC = 30 mA (2) Tamb = +25 C (2) ICC = 45 mA (3) Tamb = +85 C (3) ICC = 60 mA Fig 3. Power gain as a function of frequency; typical values DDD Fig 4. Power gain as a function of frequency; typical values DDD 1) G% 1) G% I*+] (1) ICC = 30 mA (2) Tamb = +25 C (2) ICC = 45 mA (3) Tamb = +85 C (3) ICC = 60 mA Noise figure as a function of frequency; typical values BGU8053 Product data sheet I*+] VCC = 5 V; Tamb = 25 C. VCC = 5 V;ICC = 48 mA. (1) Tamb = 40 C Fig 5. Fig 6. Noise figure as a function of frequency; typical values All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 6 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier DDD DDD 5/LQ G% 5/RXW G% I*+] VCC = 5 V; ICC = 48 mA. (1) Tamb = 40 C (2) Tamb = +25 C (2) Tamb = +25 C (3) Tamb = +85 C (3) Tamb = +85 C Input return loss as a function of frequency; typical values Fig 8. DDD VSDUV G% I*+] VCC = 5 V; ICC = 48 mA. (1) Tamb = 40 C Fig 7. Output return loss as a function of frequency; typical values DDD . 6 6 6 6 I*+] VCC = 5 V; Tamb = 25 C; ICC = 48 mA. I*+] VCC = 5 V; ICC = 48 mA. (1) Tamb = 40 C (2) Tamb = +25 C (3) Tamb = +85 C Fig 9. Wideband S-parameters as function of frequency; typical values BGU8053 Product data sheet Fig 10. Rollett stability factor as a function of frequency; typical values All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 7 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier DDD ,32 G%P DDD ,32 G%P I*+] VCC = 5 V; Pi = 15 dBm per tone; ICC = 48 mA. (1) f = 1500 MHz (2) Tamb = +25 C (2) f = 1900 MHz (3) Tamb = +85 C (3) f = 2500 MHz DDD DDD 3/G% G%P Fig 12. Output third-order intercept point as a function of supply current; typical values 3/G% G%P ,&&P$ VCC = 5 V; Pi = 15 dBm per tone; Tamb = 25 C. (1) Tamb = 40 C Fig 11. Output third-order intercept point as a function of frequency; typical values I*+] (1) Tamb = 40 C (1) f = 1500 MHz (2) Tamb = +25 C (2) f = 1900 MHz (3) Tamb = +85 C (3) f = 2500 MHz Fig 13. Output power at 1 dB gain compression as a function of frequency; typical values Product data sheet ,&&P$ VCC = 5 V; Tamb = 25 C. VCC = 5 V; ICC = 48 mA. BGU8053 Fig 14. Output power at 1 dB gain compression as a function of supply current; typical values All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 8 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier DDD OFF P$ 5ELDVNȍ Tamb = 25 C (1) VCC = 3.0 V (2) VCC = 3.3 V (3) VCC = 4.0 V (4) VCC = 4.5 V (5) VCC = 5 V Fig 15. ICC as a function of Rbias, typical values BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 9 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier *1' 9FWUOVG 9&& 12. Application information & 5 5ELDV & & 5)LQ / & 5)RXW & DDD See Table 9 for a list of components. Fig 16. Schematic of application board Table 9. List of components See Figure 16 for schematics. Component Description Value C1, C2 capacitor 100 nF C3, C5 capacitor 10 pF C4 capacitor 10 nF L1 inductor 15 nH 100 pF BGU8053 Product data sheet Remarks recommended for TDD systems R1 resistor 10 Rbias resistor 5.1 k VCC = 5 V 2.3 k VCC = 3.3 V All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 10 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier Table 10. Typical performance BGU8053 application board VCC = 5 V All RF parameters are measured at the application board as shown in Figure 16. With the components as listed in Table 9 while optimized for: f = 2500 MHz, VCC = 5 V, ICC = 48 mA and Tamb = 25 C. Symbol Parameter Conditions f (MHz) 2000 2300 2500 2700 3000 3400 3500 3800 G gain 20.2 19.0 18.3 17.6 16.6 15.4 15.1 14.2 RLin input return loss 11.0 11.8 12.3 12.6 13.3 14.0 13.8 14.9 RLout output return loss 30.1 28.9 28.7 27.1 23.4 18.2 17.3 14.7 PL(1dB) output power at 1 dB gain compression 18.5 18.6 18.2 18.1 18.2 16.9 16.2 14.9 IP3O output third-order intercept point [1] 35.5 35.4 35.4 35.2 34.3 33.4 33.3 32.5 [1][2] 34.8 36.3 36.3 36.4 35.6 32.5 33.1 31.9 [3] 0.52 0.59 0.63 0.68 0.67 0.76 0.78 0.87 NF noise figure [1] 2-Tone; tone spacing = 1 MHz, Po = 5 dBm per tone. [2] For applications where fast switching is required, the value of C1 and C2 should be changed to 100 pF. [3] Connector and board losses not de-embedded. Table 11. Typical performance BGU8053 application board VCC = 3.3 V All RF parameters measured at application board shown in Figure 16. With the components as listed in Table 9 while optimized for 2500 MHz, VCC = 3.3 V, ICC = 48 mA, Tamb =25C Symbol Parameter Conditions f (MHz) 2000 2300 2500 2700 3000 3400 3500 3800 G gain 20.1 18.9 18.1 17.4 16.4 15.3 15.0 14.1 RLin input return loss 11.3 12.1 12.4 14.1 13.6 13.7 15.0 15.3 RLout output return loss 32.9 29.5 27.8 27.5 23.4 18.6 17.7 15.4 PL(1dB) output power at 1 dB gain compression 16.0 15.4 14.9 15.1 14.5 14.0 13.9 12.7 IP3O output third-order intercept point [1] 29.2 28.8 29.0 28.1 27.1 26.0 26.3 23.4 [1][2] 30.2 29.9 29.0 29.1 28.4 26.2 25.8 25.9 [3] 0.55 0.58 0.60 0.63 0.69 0.78 0.80 0.89 NF noise figure [1] 2-Tone; tone spacing = 1 MHz, Po = 5 dBm per tone. [2] For applications where fast switching is required, the value of C1 and C2 should be changed to 100 pF. [3] Connector and board losses not de-embedded. BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 11 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 13. Package outline +:621SODVWLFWKHUPDOHQKDQFHGYHU\YHU\WKLQVPDOORXWOLQHSDFNDJHQROHDGV WHUPLQDOVERG\[[PP ' % 627 $ ; ( WHUPLQDO LQGH[DUHD $ $ F GHWDLO; H H WHUPLQDO LQGH[DUHD Y Z E H & $ % & & \ \ & / . (K 'K PP VFDOH 'LPHQVLRQVPPDUHWKHRULJLQDOGLPHQVLRQV 8QLW PP $ $ E PD[ QRP PLQ F ' 'K ( (K H H . / Y Z \ \ 1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG 2XWOLQH YHUVLRQ 627 5HIHUHQFHV ,(& -('(& -(,7$ VRWBSR (XURSHDQ SURMHFWLRQ ,VVXHGDWH 02 Fig 17. Package outline SOT1327-1 (HWSON8) BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 12 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 14. Abbreviations Table 12. Abbreviations Acronym Description CDMA Code Division Multiple Access ESD ElectroStatic Discharge FDD Frequency-Division Duplexing GSM Global System for Mobile Communication LNA Low Noise Amplifier LTE Long-Term Evolution RF Radio Frequency TDD Time-Division Duplexing W-CDMA Wideband Code Division Multiple Access 15. Revision history Table 13. Revision history Document ID Release date Data sheet status Change notice Supersedes BGU8053 v.3 20160418 Product data sheet - BGU8053 v.2 Modifications: BGU8053 v.2 Modifications: BGU8053 v.1 BGU8053 Product data sheet • • • • • 3 V to 5 V single supply added to Section 2 “Features and benefits” Figure 1 “Block diagram” on page 2 added An additional curve added to Figure 14 on page 8 Added remark to Rbias in Table 9 on page 10 Table 11 on page 11 added 20131230 • Product data sheet - BGU8053 v.1 Table 4 on page 3: The maximum value for Vctrl(sd) has been corrected to 3 V. 20131127 Product data sheet - All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 - © NXP Semiconductors N.V. 2016. All rights reserved. 13 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 16.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. BGU8053 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 14 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] BGU8053 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 18 April 2016 © NXP Semiconductors N.V. 2016. All rights reserved. 15 of 16 BGU8053 NXP Semiconductors Low noise high linearity amplifier 18. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 11.1 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Recommended operating conditions. . . . . . . . 4 Thermal characteristics . . . . . . . . . . . . . . . . . . 4 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application information. . . . . . . . . . . . . . . . . . . 9 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 12 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 13 Legal information. . . . . . . . . . . . . . . . . . . . . . . 14 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 14 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Contact information. . . . . . . . . . . . . . . . . . . . . 15 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2016. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 18 April 2016 Document identifier: BGU8053