JANUARY, 2015 AA™4325 Series Windows INDEX FIXED WINDOW................................................................................. 3-6 PROJECT-IN WINDOW.................................................................... 7-10 PROJECT-OUT WINDOW.............................................................. 11-14 INSWING CASEMENT WINDOW.................................................. 15-18 OUTSWING CASEMENT WINDOW.............................................. 19-22 RECEPTORS, SUB SILLS AND ANCHORING.................................. 23 PANNING............................................................................................ 24 THERMAL CHARTS...................................................................... 25-43 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-071 1 Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADME060 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™4325 Series Windows BLANK PAGE ADME060 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 JANUARY, 2015 EC 97911-071 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 FIXED WINDOW Standard Features Architectural Grade Window Tested to US and Canadian Standards Polyamide Thermal Break Tubular Profiles 45° Mitered Frame Corners Staked Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead • Architectural Anodized Finishes and Applied Coatings • Interior and Exterior Dual Finish Options Thermal Break Exterior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • Interior Fixed Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME060 3 AA™4325 Series Windows EC 97911-071 Architectural Class AW-PG80-FW TESTING STANDARD AAMA / WDMA CSA 101 / I.S.2 / A440-05 / A440-08 FRAME DEPTH 3-1/4" Overall Frame Depth TYPICAL WALL THICKNESS .080 Nominal Frame TYPICAL MAXIMUM SIZE 60" x 99" TYPICAL MINIMUM SIZE 17" x 17" TYPICAL CONFIGURATIONS INFILL OPTIONS 1" and 1-3/4" (Other infill options available upon request.) STANDARD HARDWARE Not Applicable OPTIONAL HARDWARE Not Applicable OTHER OPTIONS Structural Mullions Vertically or Horizontally Stacked Receptor and Sub Sill Panning Internal Blinds Exterior or Interior Muntins ADME060 kawneer.com © Kawneer Company, Inc., 2014 CLASS and GRADE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. FIXED WINDOW JANUARY, 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 kawneer.com D.L.O. W.D. O.D. 5 JAMB D.L.O. D.L.O. D.L.O. 2 HORIZONTAL D.L.O. 3-1/4"(83) 6 VERTICAL D.L.O. 6 VERTICAL 5 JAMB ADME060 3-1/4"(83) 3 4 D.L.O. D.L.O. 1 HEAD 3 SILL 4 SILL 2-1/4"(57) 6 W.D. O.D. 2-1/4"(57) W.D. O.D. 2 2-1/4"(57) 2-1/4"(57) 3/8"(10) 3/8"(10) 1 W.D. 3/8"(10) O.D. 3-1/4"(83) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 5 1/2"(13) 3-1/4"(83) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2015 AA™4325 Series Windows EC 97911-071 3-1/4"(83) 1 HEAD TYPICAL ELEVATION 2 HORIZONTAL 3 SILL 4 SILL 5 FIXED WINDOW SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 3-1/4"(83) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™4325 Series Windows BLANK PAGE ADME060 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 6 JANUARY, 2015 EC 97911-071 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 PROJECT-IN WINDOW Standard Features Architectural Grade Window Tested to US and Canadian Standards Polyamide Thermal Break Tubular Profiles 45° Mitered Vent and Frame Corners Staked Corner Joinery Factory Silicone Glazed Adjustable EURO-Groove Mounted Hardware • Interior Applied Glazing Bead • Architectural Anodized Finishes and Applied Coatings • Interior and Exterior Dual Finish Options Exterior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • Interior Project-In Window Thermal Break For specific product applications, Consult your Kawneer representative. kawneer.com ADME060 7 AA™4325 Series Windows EC 97911-071 Architectural Grade AW-PG80-AP TESTING STANDARD AAMA / WDMA CSA 101 / I.S.2 / A440-05 / A440-08 FRAME DEPTH 3-1/4" Overall Frame Depth TYPICAL WALL THICKNESS .080 Nominal Frame / .125" Nominal Vent TYPICAL MAX. VENT SIZE 60" x 36" TYPICAL MIN. VENT SIZE 24" x 19" TYPICAL CONFIGURATIONS INFILL OPTIONS 1" and 1-3/4" (Other infill options available upon request.) STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop OTHER OPTIONS Structural Mullions Vertically or Horizontally Stacked Insect Screens Receptor and Sub Sill Panning Internal Blinds Exterior or Interior Muntins ADME060 kawneer.com © Kawneer Company, Inc., 2014 CLASS and GRADE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. PROJECT-IN WINDOW JANUARY, 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 8 3-1/4"(83) © Kawneer Company, Inc., 2014 3-3/8"(86) 4 JAMB kawneer.com 3 SILL W.D. D.L.O. D.L.O. D.L.O. D.L.O. 1 HEAD 3-3/8"(86) W.D. O.D. O.D. 3-3/8"(86) W.D. 4 3-3/8"(86) 3/8"(10) 3/8"(10) 3/8"(10) 1 W.D. TYPICAL ELEVATION O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2 3 1/2"(13) 3-1/4"(83) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2015 AA™4325 Series Windows EC 97911-071 PROJECT-IN WINDOW SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 3-1/4"(83) 2 SILL 4 JAMB ADME060 3-1/4"(83) 1 HEAD 2 SILL O.D. 3 SILL 9 AA™4325 Series Windows JANUARY, 2015 A standard hinge for ventilators providing approximately 45° to 60° openings depending on size. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are an alternative to standard multi-point locking for the operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles and multi-point locking cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME060 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-071 PROJECT-IN WINDOW Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 10 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 PROJECT-OUT WINDOW Standard Features Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • Architectural Grade Window Tested to US and Canadian Standards Polyamide Thermal Break Tubular Profiles 45° Mitered Vent and Frame Corners Staked Corner Joinery Factory Silicone Glazed Adjustable EURO-Groove Mounted Hardware • Interior Applied Glazing Bead • Architectural Anodized Finishes and Applied Coatings • Interior and Exterior Dual Finish Options Exterior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Thermal Break Interior Project-out Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME060 11 AA™4325 Series Windows EC 97911-071 CLASS and GRADE Architectural Grade AW-PG80-AP TESTING STANDARD AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08 FRAME DEPTH 3-1/4" Overall Frame Depth TYPICAL WALL THICKNESS .080 Nominal Frame / .125" Nominal Vent TYPICAL MAX. VENT SIZE 60" x 36" TYPICAL MIN. VENT SIZE 24" x 19" INFILL OPTIONS 1" and 1-3/4" (Other infill options available upon request.) STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop Roto Operator OTHER OPTIONS Structural Mullions Vertically or Horizontally Stacked Insect Screens Receptor and Sub Sill Panning Internal Blinds Exterior or Interior Muntins ADME060 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. TYPICAL CONFIGURATIONS kawneer.com © Kawneer Company, Inc., 2014 PROJECT-OUT WINDOW JANUARY, 2015 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 12 kawneer.com 3-3/8"(86) O.D. D.L.O. D.L.O. D.L.O. 1 HEAD 2 SILL 3-3/8"(86) 2 3 W.D. O.D. O.D. 3-3/8"(86) W.D. 4 3-3/8"(86) 3/8"(10) 3-1/4"(83) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3/8"(10) 1 W.D. O.D. 3/8"(10) 1/2"(13) 3-1/4"(83) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2015 AA™4325 Series Windows EC 97911-071 PROJECT-OUT WINDOW SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 3-1/4"(83) 3 SILL 4 JAMB ADME060 3-1/4"(83) 1 HEAD TYPICAL ELEVATION 2 SILL W.D. D.L.O. 4 JAMB 3 SILL 13 AA™4325 Series Windows JANUARY, 2015 A standard hinge for ventilators providing approximately 45° to 60° openings depending on size. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are an alternative to standard multi-point locking for the operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles and multi-point locking cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME060 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-071 PROJECT-OUT WINDOW Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 14 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 INSWING CASEMENT WINDOW Standard Features Inswing Casement Window HINGED LEFT Thermal Break © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • Architectural Grade Window • Tested to US and Canadian Standards • Polyamide Thermal Break • Tubular Profiles • 45° Mitered Vent and Frame Corners • Staked Corner Joinery • Factory Silicone Glazed • Adjustable EURO-Groove Mounted Hardware • Interior Applied Glazing Bead • Architectural Anodized Finishes and Applied Coatings • Interior and Exterior Dual Finish Options Interior Exterior For specific product applications, Consult your Kawneer representative. kawneer.com ADME060 15 AA™4325 Series Windows EC 97911-071 CLASS and GRADE Architectural Grade AW-PG80-C TESTING STANDARD AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08 FRAME DEPTH 3-1/4" Overall Frame Depth TYPICAL WALL THICKNESS .080 Nominal Frame / .125" Nominal Vent TYPICAL MAX. VENT SIZE 36" x 60" TYPICAL MIN. VENT SIZE 19" x 24" INFILL OPTIONS 1" and 1-3/4" (Other infill options available upon request.) STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop Butt Hinges with Friction Adjusters OTHER OPTIONS Structural Mullions Vertically or Horizontally Stacked Insect Screens Receptor and Sub Sill Panning Internal Blinds Exterior or Interior Muntins ADME060 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. TYPICAL CONFIGURATIONS kawneer.com © Kawneer Company, Inc., 2014 INSWING CASEMENT WINDOW JANUARY, 2015 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 16 kawneer.com W.D. O.D. 4 JAMB 4 JAMB D.L.O. D.L.O. W.D. 5 JAMB D.L.O. 3-3/8"(86) 5 JAMB ADME060 D.L.O. D.L.O. 1 HEAD 2 SILL 3 SILL 3-3/8"(86) W.D. O.D. 2 3 3-3/8"(86) 3/8"(10) 3-1/4"(83) 3-3/8"(86) W.D. O.D. 3/8"(10) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4 W.D. O.D. 3/8"(10) 1/2"(13) 3-1/4"(83) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2015 AA™4325 Series Windows EC 97911-071 3-1/4"(83) 5 1 HEAD TYPICAL ELEVATION 2 SILL 3-3/8"(86) O.D. 3/8"(10) 3 SILL 17 INSWING CASEMENT WINDOW SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3-1/4"(83) AA™4325 Series Windows JANUARY, 2015 A standard hinge for ventilators providing approximately 45° to 60° openings depending on size. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are an alternative to standard multi-point locking for the operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles and multi-point locking cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. BUTT HINGE An optional hinge available in clear or bronze anodized finishes or painted to match window. Must be used with Friction Adjusters. ADME060 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-071 INSWING CASEMENT WINDOW Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 18 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 OUTSWING CASEMENT WINDOW Standard Features Architectural Grade Window Tested to US and Canadian Standards Polyamide Thermal Break Tubular Profiles 45° Mitered Vent and Frame Corners Staked Corner Joinery Factory Silicone Glazed Adjustable EURO-Groove Mounted Hardware • Interior Applied Glazing Bead • Architectural Anodized Finishes and Applied Coatings • Interior and Exterior Dual Finish Options Outswing Casement Window HINGED LEFT Thermal Break © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • Interior Exterior For specific product applications, Consult your Kawneer representative. kawneer.com ADME060 19 AA™4325 Series Windows EC 97911-071 CLASS and GRADE Architectural Grade AW-PG80-C TESTING STANDARD AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08 FRAME DEPTH 3-1/4" Overall Frame Depth TYPICAL WALL THICKNESS .080 Nominal Frame / .125" Nominal Vent TYPICAL MAX. VENT SIZE 36" x 60" TYPICAL MIN. VENT SIZE 19" x 24" INFILL OPTIONS 1" and 1-3/4" (Other infill options available upon request.) STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop Roto Operators Multi-Point Locks OTHER OPTIONS Structural Mullions Vertically or Horizontally Stacked Insect Screens Receptor and Sub Sill Panning Internal Blinds Exterior or Interior Muntins ADME060 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. TYPICAL CONFIGURATIONS kawneer.com © Kawneer Company, Inc., 2014 OUTSWING CASEMENT WINDOW JANUARY, 2015 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 20 kawneer.com 3-3/8"(86) W.D. O.D. 4 JAMB 4 JAMB D.L.O. D.L.O. W.D. 5 JAMB 5 JAMB ADME060 3-3/8"(86) 3/8"(10) D.L.O. D.L.O. D.L.O. 1 HEAD 2 SILL 3 SILL 3-3/8"(86) W.D. O.D. O.D. 3-3/8"(86) W.D. 3/8"(10) EC 97911-071 3-3/8"(86) 3/8"(10) 2 3 W.D. 3-1/4"(83) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4 O.D. 3/8"(10) 1/2"(13) 3-1/4"(83) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2015 AA™4325 Series Windows 3-1/4"(83) 5 1 HEAD TYPICAL ELEVATION 2 SILL O.D. 3 SILL 21 OUTSWING CASEMENT WINDOW SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3-1/4"(83) AA™4325 Series Windows EC 97911-071 A standard hinge for ventilators providing an opening of up to 45°. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are an alternative to standard multi-point locking for the operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles and multi-point locking cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME060 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. OUTSWING CASEMENT WINDOW JANUARY, 2015 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 22 6-3/4" (171.4) 4" (101.6) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1-1/4" (31.7) kawneer.com 20-0793 4-1/8" (107.7) 4" (101.6) S-11056 S-11055 3-PIECE MULLIONS ADME060 S-11038 EC 97911-071 IF-1447 2-1/2" (63.5) 3-3/4" (95) S-11038 2-1/2" (63.5) IF-1447 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2015 AA™4325 Series Windows RECEPTORS, SUB SILLS AND ANCHORING SCALE : 3" = 1'-0" (Nominal Dimensions Shown) S-071 S-071 IF-1448 2" (51) IF-1448 HEAD & JAMB RECEPTORS 4-1/16" (103.2) 20-0793 ANCHOR S-11056 S-11055 IF-1445 3-3/8" (85.7) H-11075 3-3/8" (85.7) 3-1/8" (79.4) IF-1449 50-2130 SUB SILL 50-0973 23 PRE-SET PANNING WRAP AROUND PANNING ADME060 kawneer.com © Kawneer Company, Inc., 2014 PANNINGS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™4325 Series Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 24 JANUARY, 2015 EC 97911-071 SCALE : 3" = 1'-0" (Nominal Dimensions Shown) Note: 1" glazing infill shown, 1-3/4" similar. AA™4325 Series Windows JANUARY, 2015 EC 97911-071 25 THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 51-3/4" (1315) 5'-0" (1524) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3'-0" (915) 27-3/4" (705) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = 27-3/4" • 51-3/4" = 9.97ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (9.97 ÷ 15)100 = 66% System U-factor vs Percent of Glass Area (5.00) 0.85 0.80 (4.50) 0.75 N 0.60 0.55 0.53 0.50 0.45 0.35 (2.50) (2.00) 0.30 0.20 70 66% 65 60 55 Percent of Glass Area Based on 66% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.53 Btu/hr • ft2 • °F kawneer.com (3.00) 0.40 0.25 75 (3.50) ADME060 50 (1.50) W m2 • °C System U-factor © Kawneer Company, Inc., 2014 (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) (4.00) 0.65 Btu hr • ft2 • °F System U-factor COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 E IGN PL S M E A D EX OR F T O Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.90 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS FIXED WINDOW WITH 1" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME060 kawneer.com © Kawneer Company, Inc., 2014 0.38 (2.16) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor 26 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2015 kawneer.com AA™4325 Series Windows EC 97911-071 Vision Area / Total Area (%) ADME060 27 THERMAL CHARTS FIXED WINDOW WITH 1" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance (BTU/hr • ft • °F) 2 Overall U-Factor 4 0.48 0.50 0.46 0.49 0.44 0.47 0.42 0.46 0.40 0.44 0.38 0.42 0.36 0.41 0.34 0.39 0.32 0.38 0.30 0.36 0.28 0.35 0.26 0.33 0.24 0.31 0.22 0.30 0.20 0.28 0.18 0.27 0.16 0.26 0.14 0.24 0.12 0.22 0.10 0.21 FIXED WINDOW WITH 1" GLAZING NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.64 0.75 0.64 0.70 0.60 0.70 0.60 0.65 0.56 0.65 0.55 0.60 0.52 0.60 0.51 0.55 0.47 0.55 0.47 0.50 0.43 0.50 0.43 0.45 0.39 0.45 0.38 0.40 0.35 0.40 0.34 0.35 0.30 0.35 0.30 0.30 0.26 0.30 0.26 0.25 0.22 0.25 0.21 0.20 0.18 0.20 0.17 0.15 0.13 0.15 0.13 0.10 0.09 0.10 0.09 0.05 0.05 0.05 0.04 ADME060 kawneer.com © Kawneer Company, Inc., 2014 Glass U-Factor 3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 28 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS FIXED WINDOW WITH 1-3/4" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) Btu hr • ft2 • °F System U-factor 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) 0.08 (0.45) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.22 (1.25) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME060 29 COG VT Vision Area / Total Area (%) ADME060 kawneer.com © Kawneer Company, Inc., 2014 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™4325 Series Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 30 JANUARY, 2015 EC 97911-071 FIXED WINDOW WITH 1-3/4" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) FIXED WINDOW WITH 1-3/4" GLAZING Glass U-Factor 3 Overall U-Factor 4 0.32 0.33 0.30 0.32 0.28 0.30 0.26 0.28 0.24 0.27 0.22 0.25 0.20 0.23 0.18 0.22 0.16 0.20 0.14 0.19 0.12 0.17 0.10 0.15 0.08 0.13 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.63 0.75 0.63 0.70 0.59 0.70 0.59 0.65 0.55 0.65 0.55 0.60 0.51 0.60 0.50 0.55 0.47 0.55 0.46 0.50 0.42 0.50 0.42 0.45 0.38 0.45 0.38 0.40 0.34 0.40 0.34 0.35 0.30 0.35 0.29 0.30 0.26 0.30 0.25 0.25 0.21 0.25 0.21 0.20 0.17 0.20 0.17 0.15 0.13 0.15 0.13 0.10 0.09 0.10 0.08 0.05 0.05 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance 1 (BTU/hr • ft 2 • °F) kawneer.com ADME060 31 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS PROJECT-IN WINDOW WITH 1" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME060 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 32 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2015 kawneer.com AA™4325 Series Windows EC 97911-071 Vision Area / Total Area (%) ADME060 33 THERMAL CHARTS PROJECT-IN WINDOW WITH 1" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance (BTU/hr • ft • °F) 2 Overall U-Factor 4 0.47 0.49 0.46 0.48 0.44 0.47 0.42 0.46 0.40 0.45 0.38 0.44 0.36 0.42 0.34 0.41 0.32 0.40 0.30 0.39 0.28 0.38 0.26 0.36 0.24 0.35 0.22 0.34 0.20 0.33 0.18 0.33 0.16 0.32 0.14 0.31 0.12 0.30 0.10 0.28 PROJECT-IN WINDOW WITH 1" GLAZING NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.49 0.75 0.47 0.70 0.46 0.70 0.44 0.65 0.42 0.65 0.41 0.60 0.39 0.60 0.38 0.55 0.36 0.55 0.35 0.50 0.33 0.50 0.32 0.45 0.30 0.45 0.28 0.40 0.27 0.40 0.25 0.35 0.23 0.35 0.22 0.30 0.20 0.30 0.19 0.25 0.17 0.25 0.16 0.20 0.14 0.20 0.13 0.15 0.11 0.15 0.09 0.10 0.08 0.10 0.06 0.05 0.04 0.05 0.03 ADME060 kawneer.com © Kawneer Company, Inc., 2014 Glass U-Factor 3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 34 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS PROJECT-IN WINDOW WITH 1-3/4" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) Btu hr • ft2 • °F System U-factor 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) 0.08 (0.45) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.20 (1.14) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME060 35 COG SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME060 kawneer.com © Kawneer Company, Inc., 2014 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™4325 Series Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 36 JANUARY, 2015 EC 97911-071 PROJECT-IN WINDOW WITH 1-3/4" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area Vision Area / Total Area (%) AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) PROJECT-IN WINDOW WITH 1-3/4" GLAZING Glass U-Factor 3 Overall U-Factor 4 0.32 0.34 0.30 0.33 0.28 0.32 0.26 0.30 0.24 0.29 0.22 0.28 0.20 0.27 0.18 0.25 0.16 0.24 0.14 0.23 0.12 0.22 0.10 0.21 0.08 0.19 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.48 0.75 0.47 0.70 0.45 0.70 0.44 0.65 0.42 0.65 0.41 0.60 0.39 0.60 0.38 0.55 0.36 0.55 0.35 0.50 0.33 0.50 0.32 0.45 0.29 0.45 0.28 0.40 0.26 0.40 0.25 0.35 0.23 0.35 0.22 0.30 0.20 0.30 0.19 0.25 0.17 0.25 0.16 0.20 0.14 0.20 0.13 0.15 0.10 0.15 0.09 0.10 0.07 0.10 0.06 0.05 0.04 0.05 0.03 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance 1 (BTU/hr • ft 2 • °F) kawneer.com ADME060 37 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME060 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor 38 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2015 kawneer.com AA™4325 Series Windows EC 97911-071 Vision Area / Total Area (%) ADME060 39 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance (BTU/hr • ft • °F) 2 Overall U-Factor 4 0.48 0.55 0.46 0.54 0.44 0.53 0.42 0.52 0.40 0.51 0.38 0.50 0.36 0.48 0.34 0.47 0.32 0.46 0.30 0.45 0.28 0.44 0.26 0.43 0.24 0.41 0.22 0.40 0.20 0.39 0.18 0.39 0.16 0.38 0.14 0.37 0.12 0.35 0.10 0.34 PROJECT-OUT WINDOW WITH 1" GLAZING NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.49 0.75 0.47 0.70 0.46 0.70 0.44 0.65 0.43 0.65 0.41 0.60 0.40 0.60 0.38 0.55 0.37 0.55 0.35 0.50 0.33 0.50 0.32 0.45 0.30 0.45 0.28 0.40 0.27 0.40 0.25 0.35 0.24 0.35 0.22 0.30 0.21 0.30 0.19 0.25 0.18 0.25 0.16 0.20 0.14 0.20 0.13 0.15 0.11 0.15 0.09 0.10 0.08 0.10 0.06 0.05 0.05 0.05 0.03 ADME060 kawneer.com © Kawneer Company, Inc., 2014 Glass U-Factor 3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 40 AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1-3/4" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) Btu hr • ft2 • °F System U-factor 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) 0.08 (0.45) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.20 (1.14) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME060 41 COG SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME060 kawneer.com © Kawneer Company, Inc., 2014 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™4325 Series Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 42 JANUARY, 2015 EC 97911-071 PROJECT-OUT WINDOW WITH 1-3/4" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area Vision Area / Total Area (%) AA™4325 Series Windows JANUARY, 2015 EC 97911-071 THERMAL PERFORMANCE MATRIX (NFRC SIZE) PROJECT-OUT WINDOW WITH 1-3/4" GLAZING Glass U-Factor 3 Overall U-Factor 4 0.32 0.35 0.30 0.34 0.28 0.32 0.26 0.31 0.24 0.30 0.22 0.29 0.20 0.27 0.18 0.26 0.16 0.25 0.14 0.24 0.12 0.23 0.10 0.21 0.08 0.20 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.48 0.75 0.47 0.70 0.45 0.70 0.44 0.65 0.42 0.65 0.41 0.60 0.39 0.60 0.38 0.55 0.36 0.55 0.35 0.50 0.33 0.50 0.32 0.45 0.29 0.45 0.28 0.40 0.26 0.40 0.25 0.35 0.23 0.35 0.22 0.30 0.20 0.30 0.19 0.25 0.17 0.25 0.16 0.20 0.14 0.20 0.13 0.15 0.10 0.15 0.09 0.10 0.07 0.10 0.06 0.05 0.04 0.05 0.03 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance 1 (BTU/hr • ft 2 • °F) kawneer.com ADME060 43 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™4325 Series Windows BLANK PAGE ADME060 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 44 JANUARY, 2015 EC 97911-071