PIC16F506 Memory Programming

PIC16F506
Memory Programming Specification
This document includes the
programming specifications for the
following devices:
1.1
The PIC16F506 requires one power supply for VDD and
one for VPP.
• PIC16F506
1.0
1.2
PROGRAMMING THE
PIC16F506
Program/Verify Mode
The Program/Verify mode for the PIC16F506 allows
programming of user program memory, user ID
locations, backup OSCCAL location and the
Configuration Word.
The PIC16F506 is programmed using a serial method.
The Serial mode will allow the PIC16F506 to be
programmed while in the user’s system. This allows for
increased design flexibility. This programming
specification applies to PIC16F506 devices in all
packages.
FIGURE 1-1:
Hardware Requirements
PIN DIAGRAMS
PDIP, SOIC, TSSOP
1
14
VSS
RB5/OSC1/CLKIN
2
13
RB0/ICSPDAT/C1IN+/AN0
RB4/OSC2/CLKOUT
3
12
RB1/ICSPCLK/C1IN-/AN1
MCLR/VPP/RB3
4
RC5/T0CKI
5
RC4/C2OUT
RC3
PIC16F506
VDD
11
RB2/C1OUT/AN2
10
RC0/C2IN+
6
9
RC1/C2IN-
7
8
RC2/CVREF
4
RC4/C2OUT
5
6
7
GND
RB0/C1IN+/AN0/ICSPDAT
11
RB1/C1IN-/AN1/ICSPCLK
10
RB2/C1OUT/AN2
9
8
RC0/C2IN+
RC1/C2IN-
3
RC5/T0CKI
RC3
2
RB4/OSC2/CLKOUT
RB3/MCLR/VPP
 2010 Microchip Technology Inc.
NC
PIC16F506
16 15 14 13
12
1
RC2/CVREF
RB5/OSC1/CLKIN
NC
VDD
16-Pin QFN Diagram
DS41258C-page 1
PIC16F506
TABLE 1-1:
Pin Name
PIN DESCRIPTIONS (DURING PROGRAMMING): PIC16F506
During Programming
Function
Pin Type
RB1
ICSPCLK
I
RB0
ICSPDAT
I/O
MCLR/VPP/RB3
Program/Verify mode
P
Pin Description
Clock input – Schmitt Trigger input
Data input/output – Schmitt Trigger input
(1)
Program Mode Select
VDD
VDD
P
Power Supply
VSS
VSS
P
Ground
Legend: I = Input, O = Output, P = Power
Note 1: In the PIC16F506, the programming high voltage is internally generated. To activate the Program/Verify
mode, VPP (see Table 6-1) needs to be applied to the MCLR input.
DS41258C-page 2
 2010 Microchip Technology Inc.
PIC16F506
2.1
User Program Memory Map
The user memory space extends from (0x000-0x3FF)
on the PIC16F506. In Program/Verify mode, the
program memory space extends from (0x000-0x7FF).
The first half, (0x000-0x3FF), is user program memory.
The second half, (0x400-0x7FF), is configuration
memory. The PC will increment from (0x000 to 0x3FF),
then to 0x400 (not to 0x000).
In the configuration memory space, 0x400-0x43F is
physically implemented. However, only locations
0x400 through 0x403 are available. Other locations are
reserved.
2.2
User ID Locations
A user may store identification information (ID) in four
user ID locations. The user ID locations are mapped in
[0x400:0x403]. It is recommended that the user use
only the four Least Significant bits (LSb) of each user
ID location. The user ID locations read out normally,
even after code protection is enabled. It is recommended that user ID locations are written as 'xxxx
xxxx bbbb' where 'bbbb' is user ID information.
The 12 bits may be programmed, but only the four LSbs
are displayed by MPLAB® IDE. The xxxx’s are “don’t
care” bits and are not read by MPLAB IDE.
2.3
Configuration Word
The Configuration Word is located at 0x7FF. It is only
available upon Program mode entry. Once an
Increment Address command is issued, the
Configuration Word is no longer accessible, regardless
of the address of the program counter.
Note:
By convention, the Configuration Word is
stored at the logical address location of
0xFFF within the hex file for the
PIC16F506 parts. This logical address
location may not reflect the actual physical
address of the part itself. It is the responsibility of the programming software to
retrieve the Configuration Word from the
logical address within the hex file and
translate the address to the proper
physical location for the part in use.
 2010 Microchip Technology Inc.
2.4
Oscillator Calibration Bits
The oscillator Calibration bits are stored at the Reset
vector as the operand of a MOVLW instruction.
Programming interfaces must allow users to program
the Calibration bits themselves for custom trimming of
the INTOSC. Capability for programming the
Calibration bits when programming the entire memory
array must also be maintained for backwards
compatibility.
2.5
Backup OSCCAL Value
The backup OSCCAL value 0x404 is a factory reserved
location where the OSCCAL value is stored during
testing of the INTOSC. This location is not erased
during a standard Bulk Erase, but is erased if the PC is
moved into configuration memory prior to invoking a
Bulk Erase.
If this value is erased, it is the user’s responsibility to
rewrite it back to this location for future use.
FIGURE 2-1:
User Memory
Space
MEMORY MAPPING
PIC16F506 PROGRAM
MEMORY MAP
000h
On-chip User
Program
Memory (Page 0)
1FFh
200h
On-chip User
Program
Memory (Page 1)
Reset Vector
Config Memory
Space
2.0
User ID Locations
Backup OSCCAL Value
3FEh
3FFh
400h
403h
404h
405h
Reserved
43Fh
440h
Unimplemented
Configuration Word
7FEh
7FFh
DS41258C-page 3
PIC16F506
3.0
COMMANDS AND
ALGORITHMS
3.1
Program/Verify Mode
3.1.2
The ICSPCLK pin is used for clock input and the
ICSPDAT pin is used for data input/output during serial
operation. To input a command, the clock pin is cycled
six times. Each command bit is latched on the falling
edge of the clock with the LSb of the command being
input first. The data must adhere to the setup (TSET1)
and hold (THLD1) times with respect to the falling edge
of the clock (see Table 6-1).
The Program/Verify mode is entered by holding pins
ICSPCLK and ICSPDAT low while raising VDD pin from
VIL to VDD. Then raise VPP from VIL to VIHH. Once in
this mode, the user program memory and configuration
memory can be accessed and programmed in serial
fashion. Clock and data are Schmitt Trigger input in this
mode (see Figure 3-1).
Commands that do not have data associated with them
are required to wait a minimum of TDLY2 measured
from the falling edge of the last command clock to the
rising edge of the next command clock (see Table 6-1).
Commands that do have data associated with them
(Read and Load) are also required to wait TDLY2
between the command and the data segment
measured from the falling edge of the last command
clock to the rising edge of the first data clock. The data
segment, consisting of 16 clock cycles, can begin after
this delay.
The sequence that enters the device into the
Programming/Verify mode places all other logic into the
Reset state (the MCLR pin was initially at VIL). This
means that all I/O are in the Reset state (highimpedance inputs).
3.1.1
PROGRAMMING
The programming sequence loads a word, programs,
verifies and finally increments the PC.
Program/Verify mode entry will set the address to
0x7FF. The Increment Address command will
increment the PC. The available commands are shown
in Table 3-1.
FIGURE 3-1:
Note:
After every End Programming command,
a delay of TDIS must be delayed.
The first and last clock pulses during the data segment
correspond to the Start and Stop bits, respectively.
Input data is a “don’t care” during the Start and Stop
cycles. The 14 clock pulses between the Start and Stop
cycles, clock the 14 bits of input/output data. Data is
transferred LSb first.
ENTERING HIGH
VOLTAGE PROGRAM/
VERIFY MODE
TPPDP
SERIAL PROGRAM/VERIFY
OPERATION
THLD0
During Read commands, in which the data is output
from the PIC16F506, the ICSPDAT pin transitions from
the high-impedance input state to the low-impedance
output state at the rising edge of the second data clock
(first clock edge after the Start cycle). The ICSPDAT pin
returns to the high-impedance state at the rising edge
of the 16th data clock (first edge of the Stop cycle). See
Figure 3-3.
VPP
VDD
ICSPDAT
The commands that are available are described in
Table 3-1.
ICSPCLK
TABLE 3-1:
COMMAND MAPPING FOR PIC16F506
Command
Mapping (MSb … LSb)
Data
Load Data for Program Memory
x
x
0
0
1
0
0, data (14), 0
Read Data from Program Memory
x
x
0
1
0
0
0, data (14), 0
Increment Address
x
x
0
1
1
0
Begin Programming
x
x
1
0
0
0
End Programming
x
x
1
1
1
0
Bulk Erase Program Memory
x
x
1
0
0
1
DS41258C-page 4
Externally Timed
Internally Timed
 2010 Microchip Technology Inc.
PIC16F506
3.1.2.1
Load Data For Program Memory
After receiving this command, the chip will load in a
14-bit “data word” when 16 cycles are applied, as
described previously. Because this is a 12-bit core, the
two MSbs of the data word are ignored. A timing
diagram for the Load Data command is shown in
Figure 3-2.
FIGURE 3-2:
LOAD DATA COMMAND (PROGRAM/VERIFY)
1
2
3
4
5
0
0
TSET1
THLD1
x
6
TDLY2
ICSPCLK
0
ICSPDAT
3.1.2.2
1
1
2
3
4
5
strt_bit LSb
x
16
15
MSb stp_bit
TSET1
-+THLD1
TDLY1
Read Data From Program Memory
After receiving this command, the chip will transmit
data bits out of the program memory (user or
configuration) currently addressed, starting with the
second rising edge of the clock input. The data pin will
go into Output mode on the second rising clock edge,
and it will revert to Input mode (high-impedance) after
the 16th rising edge. Because this is a 12-bit core, the
two MSbs of the 14-bit word will be read as ‘0’s.
If the program memory is code-protected (CP = 0),
portions of the program memory will be read as zeros.
See Section 5.0 “Code Protection” for details.
FIGURE 3-3:
READ DATA FROM PROGRAM MEMORY COMMAND
TDLY2
1
2
3
4
1
0
5
1
6
ICSPCLK
ICSPDAT
2
3
4
5
15
16
TDLY3
1 0
0
x
x
strt_bit
TDLY1
TSET1
MSb stp_bit
LSb
THLD1
Input
 2010 Microchip Technology Inc.
Output
Input
DS41258C-page 5
PIC16F506
3.1.2.3
Increment Address
The PC is incremented when this command is
received. A timing diagram of this command is shown
in Figure 3-4.
It is not possible to decrement the address counter. To
reset this counter, the user must either exit and re-enter
Program/Verify mode or increment the PC from 0x7FF
to 0x000.
FIGURE 3-4:
INCREMENT ADDRESS COMMAND
TDLY2
1
2
3
4
5
Next Command
1
6
2
ICSPCLK
ICSPDAT
0
1
1
0
x
x
TSET1
THLD1
3.1.2.4
Begin Programming (Externally
Timed)
A Load command must be given before every Begin
Programming command. Programming will begin after
this command is received and decoded. Programming
requires (TPROG) time and is terminated using an End
Programming command. This command programs the
current location, no erase is performed.
FIGURE 3-5:
BEGIN PROGRAMMING (EXTERNALLY TIMED)
TPROG
1
2
3
0
0
0
4
5
6
x
x
End Programming Command
1
2
ICSPCLK
ICSPDAT
TSET1
DS41258C-page 6
1
0
1
THLD1
 2010 Microchip Technology Inc.
PIC16F506
3.1.2.5
End Programming
The End Programming command terminates the
program process. A delay of TDIS (see Table 6-1) is
required before the next command to allow the internal
programming voltage to discharge (see Figure 3-6).
FIGURE 3-6:
END PROGRAMMING (EXTERNALLY TIMED)
TDIS
1
2
3
4
0
1
1
1
5
6
Next Command
1
2
ICSPCLK
ICSPDAT
x
TSET1
3.1.2.6
Bulk Erase Program Memory
After this command is performed, the entire program
memory and Configuration Word is erased.
x
THLD1
To perform a full device Bulk Erase of the program
memory, configuration fuses, user IDs and backup
OSCCAL, the following sequence must be performed
(see Figure 3-13).
Note:
A fully erased part will read ‘1’s in every
program memory location.
1.
Note:
The oscillator Calibration bits are erased if
a Bulk Erase is invoked. They must be
read and saved prior to erasing the device
and restored during the programming
operation. Oscillator Calibration bits are
stored at the Reset vector as the operand
of a MOVLW instruction.
2.
3.
4.
5.
6.
7.
Read and save 0x3FF oscillator Calibration bits
and 0x404 backup OSCCAL bits into computer/
programmer temporary memory.
Enter Program/Verify mode.
Increment PC to 0x400 (first user ID location).
Perform a Bulk Erase command.
Wait TERA to complete Bulk Erase.
Restore OSCCAL bits.
Restore backup OSCCAL bits.
To perform a Bulk Erase of the program memory and
configuration fuses, the following sequence must be
performed (see Figure 3-12).
1.
2.
3.
4.
5.
6.
Read and save 0x3FF oscillator Calibration bits
and 0x404 backup OSCCAL bits into computer/
programmer temporary memory.
Enter Program/Verify mode. PC is set to
Configuration Word address.
Perform a Bulk Erase Program Memory
command.
Wait TERA to complete Bulk Erase.
Restore OSCCAL bits.
Restore backup OCCAL bits.
 2010 Microchip Technology Inc.
DS41258C-page 7
PIC16F506
TABLE 3-2:
BULK ERASE RESULTS
Program Memory Space
PC =
Configuration Memory Space
Program Memory
Reset Vector
Configuration
Word
User ID
Backup
OSCCAL
Configuration Word or
Program Memory Space
E
E
E
U
U
First User ID Location
E
E
E
E
E
Legend: E = Erased, U = Unaffected
FIGURE 3-7:
BULK ERASE PROGRAM MEMORY COMMAND
TERA
1
2
3
0
0
4
5
6
Next Command
1
2
ICSPCLK
1
ICSPDAT
1
x
x
TSET1
THLD1
DS41258C-page 8
 2010 Microchip Technology Inc.
PIC16F506
FIGURE 3-8:
READING AND TEMPORARY SAVING OF THE OSCCAL CALIBRATION BITS
Start
Enter Programming
Mode
Increment
Address
No
PC = 0x3FF?
Yes
Read Calibration
Bits and Save in
Computer/Programmer
Temp. Memory
Increment
Address
No
PC = 0x404?
Yes
Read Backup OSCCAL
Calibration Bits
and Save in
Computer/Programmer
Temp. Memory
Exit Programming
Mode
Done
 2010 Microchip Technology Inc.
DS41258C-page 9
PIC16F506
FIGURE 3-9:
RESTORING/PROGRAMMING THE OSCCAL CALIBRATION BITS
Start
Enter Programming
Mode
Increment
Address
No
PC = 0x3FF?
Yes
Read Calibration
Bits from
Computer/Programmer
Temp. Memory
Write Calibration Bits
back as the operand
of a MOVLW instruction
to 0x3FF
Increment
Address
No
PC = 0x404?
Yes
Read Backup OSCCAL
Calibration Bits from
Computer/Programmer
Temp. Memory
Write Backup OSCCAL
Bits back to 0x404
Exit Programming Mode
Done
DS41258C-page 10
 2010 Microchip Technology Inc.
PIC16F506
FIGURE 3-10:
PROGRAM FLOWCHART – PIC16F506 PROGRAM MEMORY
Start
Read and save
OSCCAL bits
(Figure 3-8)
Enter Programming
Mode
PC = 0x7FF
(Config Word)
Increment
Address
Bulk Erase
Device
PROGRAM CYCLE
Load Data
for
Program Memory
One Word
Program Cycle
Begin
Programming
Command
(Externally timed)
Read Data
from
Program Memory
Data Correct?
No
Yes
Increment
Address
Command
No
All Programming
Locations
Done?
Report
Programming
Failure
Wait TPROG
End
Programming
Wait TDIS
Yes
Exit Programming
Mode
Restore OSCCAL bits
(Figure 3-9)
Program
Configuration
Memory
(Figure 3-11)
Done
 2010 Microchip Technology Inc.
DS41258C-page 11
PIC16F506
FIGURE 3-11:
PROGRAM FLOWCHART – PIC16F506 CONFIGURATION MEMORY
Start
Enter Programming
Mode
PC = 0x7FF
(Config Word)
Load Data
Command
Programs Configuration Word
One-Word
Programming
Cycle
(see Figure 3-10)
Read Data
Command
Data
Correct?
No
Report
Programming
Failure
Yes
Increment
Address
Command
No
Address =
0x400?
Yes
Load Data
Command
Programs User IDs
One-Word
Programming
Cycle
(see Figure 3-10)
Read Data
Command
Data
Correct?
No
Report
Programming
Failure
Yes
Increment
Address
Command
No
Address =
0x404?
Yes
Exit Programming
Mode
Done
DS41258C-page 12
 2010 Microchip Technology Inc.
PIC16F506
FIGURE 3-12:
PROGRAM FLOWCHART – ERASE PROGRAM MEMORY, CONFIGURATION
WORD
Start
Bulk Erase Device
Read and save
OSCCAL bits
(Figure 3-8)
Enter
Program/Verify mode
PC = 0x7FF
(Config Word)
Wait TERA
Restore OSCCAL Bits
(Figure 3-9)
Exit Programming
Mode
Done
 2010 Microchip Technology Inc.
DS41258C-page 13
PIC16F506
FIGURE 3-13:
PROGRAM FLOWCHART – ERASE PROGRAM MEMORY, CONFIGURATION
WORD AND USER ID
Read and save
OSCCAL bits
(Figure 3-8)
Start
Enter
Program/Verify mode
PC = 0x7FF
(Config Word)
Increment
PC
No
PC = 0x400?
(First User ID)
Yes
Bulk Erase
Device
Wait TERA
Restore
OSCCAL bits
(Figure 3-9)
Exit Programming
Mode
Done
DS41258C-page 14
 2010 Microchip Technology Inc.
PIC16F506
4.0
CONFIGURATION WORD
The PIC16F506 has several Configuration bits. These
bits can be programmed (reads ‘0’) or left unchanged
(reads ‘1’), to select various device configurations.
REGISTER 4-1:
—
—
CONFIGURATION WORD – PIC16F506
—
—
—
IOSCFS MCLRE
CP
WDTE
FOSC2
FOSC1
bit 11
FOSC0
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 11-7
Unimplemented: Read as ‘1’
bit 6
IOSCFS: Internal Oscillator Frequency Select bit
1 = 8 MHz
0 = 4 MHz
bit 5
MCLRE: Master Clear Enable bit
1 = MCLR/VPP/RB3 pin functions as MCLR
0 = MCLR/VPP/RB3 pin functions as RB3, MCLR internally tied to VDD
bit 4
CP: Code Protection bit
1 = Code protection off
0 = Code protection on
bit 3
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
bit 2-0
FOSC2:FOSC0: Oscillator Selection bits
000 = LP oscillator
001 = XT oscillator
010 = HS oscillator
011 = EC oscillator with RB4 function on RB4/OSC2/CLKOUT
100 = INTOSC with RB4 function on RB4/OSC2/CLKOUT
101 = INTOSC with CLKOUT function on RB4/OSC2/CLKOUT
110 = EXTRC with RB4 function on RB4/OSC2/CLKOUT
111 = EXTRC with CLKOUT function on RB4/OSC2/CLKOUT
 2010 Microchip Technology Inc.
x = Bit is unknown
DS41258C-page 15
PIC16F506
5.0
CODE PROTECTION
5.3
Checksum Computation
For the PIC16F506, once code protection is enabled,
program memory locations 0x040-0x3FE inclusive,
read all ‘0’s. Program memory locations 0x000-0x03F
and 0x3FF are always unprotected. The user ID
locations, backup OSCCAL location and the Configuration Word read out in an unprotected fashion. It is
possible to program the user ID locations, backup
OSCCAL location and the Configuration Word after
code-protect is enabled.
5.3.1
5.1
The checksum is calculated by summing the following:
Disabling Code Protection
It is recommended that the following procedure be
performed before any other programming is attempted.
It is also possible to turn code protection off (CP = 1)
using this procedure. However, all data within the
program memory will be erased when this
procedure is executed, and thus, the security of the
code is not compromised.
To disable code-protect:
a)
b)
Enter Program mode.
Execute Bulk Erase
command (001001).
Wait TERA.
c)
5.2
Note:
Checksum is calculated by reading the contents of the
PIC16F506 memory locations and adding up the
opcodes up to the maximum user addressable location
(e.g., 0x3FF for the PIC16F506). Any Carry bits
exceeding 16 bits are neglected. Finally, the Configuration Word (appropriately masked) is added to the
checksum. Checksum computation for the PIC16F506
is shown in Table 5-1.
• The contents of all program memory locations
• The Configuration Word, appropriately masked
• Masked ID locations (when applicable)
The Least Significant 16 bits of this sum is the
checksum.
The following table describes how to calculate the
checksum for each device.
Note:
Program
Memory
CHECKSUM
The
checksum
calculation
differs
depending on the code-protect setting.
The Configuration Word and ID locations
can always be read regardless of the
code-protect settings.
Embedding Configuration Word
and User ID Information in the Hex
File
To allow portability of code, the
programmer is required to read the
Configuration Word and user ID locations
from the hex file when loading the hex file.
If Configuration Word information was not
present in the hex file, then a simple
warning message may be issued.
Similarly, while saving a hex file,
Configuration Word and user ID
information must be included. An option to
not include this information may be
provided.
Microchip Technology Incorporated feels
strongly that this feature is important for
the benefit of the end customer.
DS41258C-page 16
 2010 Microchip Technology Inc.
PIC16F506
TABLE 5-1:
Device
PIC16F506
CHECKSUM COMPUTATIONS – PIC16F506(1)
Code-Protect
Checksum*
Blank
Value
0x723 at 0
and Max
Address
OFF
SUM[0x000:0x3FE] + CFGW & 0x07F
0xEC80
0xDAC8
ON
SUM[0x00:0x3F] + CFGW & 0x07F + SUM_ID
0xECAF
0xD21B
Legend: CFGW = Configuration Word
SUM[a:b] = [Sum of locations a to b inclusive]
SUM_ID = User ID locations masked by 0xF then made into a 16-bit value with ID0 as the Most Significant
nibble.
For example, ID0 = 0x1, ID1 = 0x2, ID2 = 0x3, ID3 = 0x4, then SUM_ID = 0x1234.
*Checksum = [Sum of all the individual expressions] MODULO [0xFFFF]
+ = Addition
& = Bitwise AND
Note 1: Checksum shown assumes that SUM_ID contains the unprotected checksum.
 2010 Microchip Technology Inc.
DS41258C-page 17
PIC16F506
6.0
PROGRAM/VERIFY MODE ELECTRICAL CHARACTERISTICS
TABLE 6-1:
AC/DC CHARACTERISTICS TIMING REQUIREMENTS FOR PROGRAM/VERIFY
MODE
AC/DC CHARACTERISTICS
Sym.
Characteristics
Standard Operating Conditions (unless otherwise
stated)
Operating Temperature 10°C  TA 40°C
Operating Voltage
4.5V  VDD 5.5V
Min.
Typ.
Max.
Units
VDDPROG VDD level for programming operations,
program memory
4.5
—
5.5
V
VDDERA
VDD level for Bulk Erase operations, program
memory
4.5
—
5.5
V
IDDPROG
IDD level for programming operations, program
memory
—
—
0.5
mA
IDDERA
IDD level for Bulk Erase operations, program
memory
—
—
0.5
mA
VPP
High voltage on MCLR for Program/Verify
mode entry
12.5
—
13.5
V
IPP
MCLR pin current during Program/Verify mode
—
—
0.45
mA
TVHHR
MCLR rise time (VSS to VIHH) for Program/
Verify mode entry
—
—
1.0
s
TPPDP
Hold time after VPP
5
—
—
s
VIH1
(ICSPCLK, ICSPDAT) input high-level
0.8 VDD
—
—
V
VIL1
(ICSPCLK, ICSPDAT) input low-level
—
—
0.2 VDD
V
TSET0
ICSPCLK, ICSPDAT setup time before
MCLR (Program/Verify mode selection
pattern setup time)
100
—
—
ns
THLD0
ICSPCLK, ICSPDAT hold time after MCLR
(Program/Verify mode selection pattern setup
time)
5
—
—
s
Conditions/
Comments
General
Serial Program/Verify
TSET1
Data in setup time before clock
100
—
—
ns
THLD1
Data in hold time after clock
100
—
—
ns
TDLY1
Data input not driven to next clock input (delay
required between command/data or command/
command)
1.0
—
—
s
TDLY2
Delay between clockto clockof next
command or data
1.0
—
—
s
TDLY3
Clock to data out valid (during Read Data)
—
—
80
ns
TERA
Erase cycle time
—
—
10(1)
ms
TPROG
Programming cycle time (externally timed)
—
—
2(1)
ms
TDIS
Time delay for internal programming voltage
discharge
100
—
—
s
TRESET
Time between exiting Program mode with VDD
and VPP at GND and then re-entering Program
mode by applying VDD
—
10
—
ms
Note 1:
Minimum time to ensure that function completes successfully over voltage, temperature and device
variations.
DS41258C-page 18
 2010 Microchip Technology Inc.
PIC16F506
REVISION HISTORY
Revision C (02/2010)
Revised Section 1.1; Added QFN pin diagram; Revised
Note 1, Table 1-1; Revised Section 3.1, 1st para;
Added Revision History.
 2010 Microchip Technology Inc.
DS41258C-page 19
PIC16F506
NOTES:
DS41258C-page 20
 2010 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified
logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance,
TSHARC, UniWinDriver, WiperLock and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2010, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-60932-034-8
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
 2010 Microchip Technology Inc.
DS41258C-page 21
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/05/10
DS41258C-page 22
 2010 Microchip Technology Inc.