Download

NX-series System Unit
NX-PD/PF/PC/TBX
CSM_NX-PD_PF_PC_TBX_DS_E_3_5
Power Supply Unit, Power Connection
Unit, and FG Terminal Expansion Unit
for NX-series
• Provide stabilised power to the internal circuits of NX I/O Units.
• Feed additional power to I/O circuits of NX I/O Units.
• Provide extra terminals for sensor/actuator power and
termination of shielded cabling.
Features
•
•
•
•
•
•
•
•
Units to feed in additional Unit power and I/O power to an NX-series remote I/O terminal.
Screwless clamp terminal block significantly reduces wiring work.
Space-saving 12 mm wide units.
The NX Unit Power Supply Unit allows expansion of the I/O configuration beyond the maximum power supply capacity of the EtherCAT Coupler
The I/O Power Supply Unit is used when the total allowed I/O current per feed terminal is exceeded, or to split I/O power into groups.
The I/O Power Connection Unit can be used as an additional power supply terminal for connected sensors and actuators.
The FG Terminal Expansion Unit can be used as ground terminal for wire shields.
The screwless terminal block is detachable for easy commissioning and maintenance.
System Configuration
Sysmac Studio
Support Software
EtherCAT master*
NJ-series CPU Unit
Connection to peripheral USB port
or built-in EtherNet/IP port on
NJ-series CPU Unit
Built-in EtherCAT port
Sysmac Studio
Support Software
●EtherCAT Slave Terminal
Communications cable
Ethernet cables
Peripheral USB port.
NX Series
EtherCAT Coupler Unit
NX-ECC@@@
Connection to peripheral USB
port on EtherCAT Coupler Unit
NX Units
End Cover
* OMRON CJ1W-NC@81/@82 Position Control Units cannot be connected to the EtherCAT Slave Terminal even though they support EtherCAT.
Sysmac® is a trademark or registered trademark of OMRON Corporation in Japan and other countries for OMRON factory automation products.
EtherCAT® is a registered trademark of Beckhoff Automation GmbH for their patented technology. Other company names and product names in this document are the
trademarks or registered trademarks of their respective companies.
1
NX-PD/PF/PC/TBX
Power Supply Systems
Communications Coupler Unit
Unit power supply
terminals
NX Unit
NX Unit
Additional NX Unit
power supply Power Supply Unit
NX Unit
power supply
Internal power
supply circuit
The I/O power supply is
separated.
The I/O power
supply is not
separated.
NX bus
I/O power
supply
To external
devices
I/O power supply terminals
Unit
power supply
(24 VDC)
To external
devices
External External
input
input
device device
Additional
I/O I/O Power To external
power Supply
devices
supply Unit
End Cover
I/O power supply (Supply from external source)
Note: Supply the Unit power and the I/O power from different power supplies. If you supply power from the same power supply the galvanic
separation between the bus system and the I/O circuits is no longer effective. Noise generated in the I/O circuits may cause malfunctions
in the internal circuits of the units.
2
NX-PD/PF/PC/TBX
Ordering Information
International Standards
• The standards are abbreviated as follows: U: UL, U1: UL(Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus
(Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, CE: EC Directives, and KC: KC Registration.
• Contact your OMRON representative for further details and applicable conditions for these standards.
Additional NX Unit Power Supply Unit
Unit type
Product Name
Power supply
voltage
NX Bus power supply
capacity
NX Unit power
consumption
Model
Standards
Additional NX Unit
Power Supply Unit
NX Series
System Unit
24 VDC
(20.4 to 28.8 VDC)
10 W max.
0.45 W max.
NX-PD1000
UC1, N, L,
CE, KC
Additional I/O Power Supply Unit
Unit type
Product Name
Power supply
voltage
Additional I/O Power
Supply Unit
NX Series
System Unit
I/O power feed
maximum current
NX Unit power
consumption
4A
5 to 24 VDC
(4.5 to 28.8 VDC)
Model
Standards
NX-PF0630
UC1, N, L,
CE, KC
0.45 W max.
10 A
NX-PF0730
I/O Power Supply Connection Unit
Unit type
Product Name
I/O Power Supply
Connection Unit
NX Series
System Unit
Number of I/O
power
terminals
Current capacity of
I/O power terminal
NX Unit power
consumption
Model
Standards
IOG: 16 terminals
4 A/terminal max.
0.45 W max.
NX-PC0010
UC1, N, L,
CE, KC
IOV: 16 terminals
4 A/terminal max.
0.45 W max.
NX-PC0020
UC1, N, L,
CE, KC
IOV:8 terminals
IOG:8 terminals
4 A/terminal max.
0.45 W max.
NX-PC0030
UC1, N, L,
CE, KC
Shield Connection Unit
Unit type
Product Name
Number of shield terminals
NX Unit power
consumption
Model
Standards
Shield Connection
Unit
NX Series
System Unit
14 terminals
(The following two terminals are functional
ground terminals.)
0.45 W max.
NX-TBX01
UC1, N, L,
CE, KC
3
NX-PD/PF/PC/TBX
Optional Products
Product Name
Unit/Terminal Block Coding Pins
Specification
Model
For 10 Units
(Terminal Block: 30 pins, Unit: 30 pins)
Standards
−
NX-AUX02
Specification
Product Name
No. of
terminals
Terminal
number
indications
8
Terminal Block
A/B
16
Ground
terminal
mark
Terminal
current
capacity
Model
None
NX-TBA082
Provided
NX-TBC082
None
10 A
Provided
Standards
NX-TBA162
---
NX-TBC162
Accessories
There are no accessories.
General Specification
Item
Specification
Enclosure
Mounted in a panel
Grounding method
Ground to 100 Ω or less
Ambient operating temperature
0 to 55°C
Ambient operating humidity
10% to 95% (with no condensation or icing)
Atmosphere
Must be free from corrosive gases.
Ambient storage temperature
−25 to 70°C (with no condensation or icing)
Altitude
2,000 m max.
Pollution degree
2 or less: Conforms to JIS B3502 and IEC 61131-2.
Operating
Noise immunity
environment
Overvoltage category
2 kV on power supply line (Conforms to IEC61000-4-4.)
Category II: Conforms to JIS B3502 and IEC 61131-2.
EMC immunity level
Zone B
Vibration resistance
Conforms to IEC 60068-2-6.
5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2, 100 min each
in X, Y, and Z directions
(10 sweeps of 10 min each = 100 min total)
Shock resistance
Conforms to IEC 60068-2-27. 147 m/s2, 3 times each in X, Y, and Z directions
Applicable standards
cULus: Listed UL508 and ANSI/ISA 12.12.01
EC: EN 61131-2 and C-Tick, KC Registration, NK, LR
4
NX-PD/PF/PC/TBX
Specification
Additional NX Unit Power Supply Unit NX-PD1000
Unit name
Additional NX Unit Power Supply Unit
Model
NX-PD1000
External connection
terminals
Screwless push-in terminal block (8 terminals)
Power supply voltage
24 VDC (20.4 to 28.8 VDC)
NX Bus power supply
capacity
10 W max. (Refer to Installation orientation and restrictions for details.)
NX Unit power supply
efficiency
70%
Unwired terminal
current capacity
4 A max. (Including the current of through-wiring)
Dimensions
12 (W) × 100 (H) 71 × (D)
Isolation method
No-isolation
Insulation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
No consumption
Weight
65 g max.
+
+
Terminal
block
−
(Functional ground
terminal)
−
(Functional ground
terminal)
Circuit layout
No-isolation
power
supply
circuit
UNIT PWR
LED
NX Unit power supply +
NX Unit power supply +
Internal
circuits
NX bus
connector
(left)
NX Unit power supply -
NX Unit power supply −
I/O power supply +
I/O power supply +
I/O power supply -
I/O power supply -
NX bus
connector
(right)
DIN Track contact plate
(Unit track surface)
5
NX-PD/PF/PC/TBX
Installation orientation: Possible in 6 orientations.
Restrictions:
• For upright installation
For 10 W output, 40ºC
Output power (W)
12
10
For 8.5 W output, 55ºC
8
6
4
2
0 0
Installation orientation
and restrictions
10
20
30
40 45 50 55 60
Ambient operating temparature (ºC)
• For any installation other than upright
For 10 W output, 40ºC
Output power (W)
12
10
8
For 6.0 W output, 55ºC
6
4
2
0 0
10
20
30
40 45 50 55 60
Ambient operating temperature (ºC)
Additional NX Unit
Power Supply Unit
NX-PD1000
A1
24 VDC Unit
power supply
Terminal connection
diagram
Through-wiring for surplus terminals*1
B1
UV
UV
UG
UG
NC*2 NC*2
Ground of 100 Ω
or less
A8
B8
*1. You can use the unwired terminals of the Unit power supply terminals (UV/UG) for through-wiring of the Additional NX Unit Power Supply Unit
or the Unit power supply terminals on the EtherCAT Coupler Unit.
*2. The NC terminal is not connected to the internal circuit.
6
NX-PD/PF/PC/TBX
Additional I/O Power Supply Units NX-PF0@30
Unit name
Additional I/O Power Supply Unit
Model
NX-PF0630
External connection
terminals
Screwless push-in terminal block (8 terminals)
Power supply voltage
5 to 24 VDC (4.5 to 28.8 VDC)*
I/O power supply
maximum current
4A
10 A
Current capacity of I/O
power supply terminal
4 A max.
10 A max.
Dimensions
12 (W) × 100 (H) 71 × (D)
Isolation method
No-isolation
Insulation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
10 mA max.
Weight
65 g max.
IOV
IOV
…
NX-PF0730
IOV
IOG
IOG
…
Terminal block
IOG
Circuit layout
NX Unit power supply +
NX Unit power supply +
Internal circuits
NX bus
connector
(left)
NX Unit power supply -
NX Unit power supply -
I/O power supply +
I/O power supply +
I/O power supply -
I/O power supply -
NX bus
connector
(right)
IO PWR Indicator
Installation orientation
and restrictions
Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions
Additional I/O
Power Supply Unit
NX-PF0630
A1
B1
IOV
DC Input Unit
A1
IOV
24 VDC
Terminal connection
diagram
IOG
A8
Overload/low voltage
detection
IOG
IOV
IOV
IOG
IOG
B8
A8
B1
0
1
IOV
IOV
IOG
IOG
2
3
IOV
IOV
IOG
IOG
Two-wire type
Three-wire type
B8
Not supported
Protective function
Not supported.
* Use an output voltage that is appropriate for the I/O circuits of the NX Units and the connected external devices.
7
NX-PD/PF/PC/TBX
I/O Power Supply Connection Unit IOG terminal type NX-PC0010
Unit name
I/O Power Supply Connection Unit
Model
NX-PC0010
External connection
terminals
Screwless push-in terminal block (16 terminals)
Number of I/O power
supply terminals
IOG: 16 terminals
Current capacity of I/O
power supply terminal
4 A/terminal max.
Dimensions
12 (W) × 100 (H) 71 ×(D)
Isolation method
No-isolation
Insulation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
No consumption
Weight
65 g max.
IOG
IOG
…
Terminal block
IOG
Circuit layout
NX Unit power supply +
NX Unit power supply +
Internal circuits
NX bus
NX Unit power supply −
connector
(left)
I/O power supply +
NX Unit power supply − NX bus
connector
(right)
I/O power supply +
I/O power supply −
Installation orientation
and restrictions
I/O power supply −
Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions
I/O Power Supply
Connection Unit
NX-PC0010 B1
A1
IOG IOG
Terminal connection
diagram
A8
DC Input Unit
or
Transistor Output Unit
A1
B1
0
1
IOV
IOV
IOG
IOG
IOG
IOG
2
3
IOG
IOG
IOV
IOV
IOG
IOG
4
5
IOG
IOG
IOV
IOV
IOG
IOG
6
7
IOG
IOG
IOV
IOV
B8
A8
Three-wire type
B8
8
NX-PD/PF/PC/TBX
I/O Power Supply Connection Unit IOV terminal type NX-PC0020
Unit name
I/O Power Supply Connection Unit
Model
NX-PC0020
External connection
terminals
Screwless push-in terminal block (16 terminals)
Number of I/O power
supply terminals
IOV: 16 terminals
Current capacity of I/O
power supply terminal
4 A/terminal max.
Dimensions
12 (W) × 100 (H) 71 × (D)
Isolation method
No-isolation
Isolation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
No consumption
Weight
65 g max.
…
Terminal block
IOV
IOV
IOV
NX Unit power supply +
Circuit layout
NX bus
connector
(left)
Installation orientation
and restrictions
NX Unit power supply +
Internal circuits
NX Unit power supply −
I/O power supply +
NX Unit power supply − NX bus
connector
I/O power supply +
(right)
I/O power supply −
I/O power supply −
Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions
I/O Power Supply
Connection Unit
A1 NX-PC0020 B1
IOV IOV
Terminal connection
diagram
A8
DC Input Unit
or
Transistor Output Unit
A1
B1
0
1
IOV
IOV
IOG
IOG
IOV
IOV
2
3
IOV
IOV
IOG
IOG
IOV
IOV
4
5
IOV
IOV
IOG
IOG
IOV
IOV
6
7
IOV
IOV
IOG
IOG
B8
A8
Three-wire type
B8
9
NX-PD/PF/PC/TBX
I/O Power Supply Connection Unit IOV/IOG terminal type NX-PC00300
Unit name
I/O Power Supply Connection Unit
Model
NX-PC0030
External connection
terminals
Screwless push-in terminal block (16 terminals)
Number of I/O power
supply terminals
IOV: 8 terminals
IOG: 8 terminals
Current capacity of I/O
power supply terminal
4 A/terminal max.
Dimensions
12 (W) × 100 (H) 71 × (D)
Isolation method
No-isolation
Insulation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
No consumption
Weight
65 g max.
…
IOV
IOV
IOV
Terminal block
Circuit layout
…
IOG
IOG
IOG
NX Unit power supply +
NX Unit power supply +
Internal circuits
NX bus
NX Unit power supply −
connector
(left)
I/O power supply +
NX Unit power supply −
I/O power supply +
I/O power supply −
Installation orientation
and restrictions
NX bus
connector
(right)
I/O power supply −
Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions
I/O Power Supply
Connection Unit
NX-PC0030
A1
Terminal connection
diagram
A8
B1
DC Input Unit
or
Transistor Output Unit
A1
IOV
IOV
0
1
IOG
IOG
2
3
IOV
IOV
4
5
IOG
IOG
6
7
IOV
IOV
8
9
IOG
IOG
10
11
IOV
IOV
12
13
IOG
IOG
14
15
B8
A8
Three-wire type
B1
B8
10
NX-PD/PF/PC/TBX
Shield Connection Unit NX-TBX01
Shield Connection Unit
Model
NX-TBX01
External connection
terminals
Screwless push-in terminal block (16 terminals)
Number of shield
terminals
14 terminals (The following two terminals are functional ground terminals.)
Dimensions
12 (W) × 100 (H) 71 × (D)
Isolation method
Isolation between the SHLD functional ground terminal, and internal circuit: No-isolation
Insulation resistance
20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength
510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max.
NX Unit power
consumption
0.45 W max.
I/O current
consumption
No consumption
Weight
65 g max.
SHLD terminal
SHLD terminal
Terminal
block
…
Unit name
SHLD terminal
(Functional ground terminal)
(Functional ground terminal)
NX Unit power supply +
Circuit layout
NX bus
connector
(left)
NX Unit power supply +
Internal circuits
NX Unit power supply −
NX Unit power supply −
I/O power supply +
I/O power supply +
I/O power supply −
I/O power supply −
NX bus
connector
(right)
DIN Track contact plate
(Unit back surface)
Installation orientation
and restrictions
Installation orientation: Possible in 6 orientations.
Restrictions: No restrictions
Shield
Connection Unit
NX-TBX01
A1
Terminal connection
diagram
Incremental Encoder
Input Unit
(Open collector input)
B1
A1
A8
SHLD
A
B
SHLD
SHLD
Z
NC
SHLD
SHLD
IOV
IOV
SHLD
SHLD
IOG
IOG
SHLD
SHLD
I0
I1
SHLD
SHLD
B8
A8
Rotary Encoder
B1
SHLD
SHLD SHLD
Shield
I2
NC
IOV
IOV
IOG
IOG
B8
Ground of 100 Ω
or less
11
NX-PD/PF/PC/TBX
Version Information
NX Units
Model
Corresponding unit versions/versions *
Unit Version
EtherCAT Coupler Units
NX-ECC20@
NJ/NX-series CPU Units
NX-PD1000
Ver.1.06 or higher
NX-PF0630
Ver.1.08 or higher
NX-PF0730
NX-PC0020
NX-PC0010
NX-PC0030
Sysmac Studio
Ver.1.0
Ver.1.0 or later
Ver.1.05 or later
Ver.1.06 or higher
NX-TBX01
* Some Units do not have all of the versions given in the above table. If a Unit does not have the specified version, support is provided by the
oldest available version after the specified version. Refer to the user’s manuals for the specific Units for the relation between models and
versions.
12
NX-PD/PF/PC/TBX
External Interface
Additional NX Unit Power Supply Unit, Additional I/O Power Supply Unit, I/O Power Supply
Connection Unit, and Shield Connection Unit
NX-PD1000/NX-PF0@30/NX-PC00@0/NX-TBX01
(B)
(C)
(A)
Symbol
Name
Function
(A)
NX bus connector
This connector is used to connect each Unit.
(B)
Indicators
The indicators show the current operating status of the Unit.
(C)
Terminal block
The terminal block is used to connect external devices.
The number of terminals depends on the type of Unit.
Terminal Blocks
(A)
(B)
A1
B1
A1
B1
A2
B2
A2
B2
A3
B3
A3
B3
A4
B4
A4
B4
A5
B5
A5
B5
A6
B6
A6
B6
A7
B7
A7
B7
A8
B8
A8
B8
(C)
8-terminal type
Symbol
16-terminal type
Name
Function
Terminal numbers for which A and B indicate the column, and 1 to 8 indicate the line are
displayed. The terminal number is a combination of column and line, so A1 to A8 and B1 to
B8 are displayed.
The terminal number indications are the same regardless of the number of terminals on the
terminal block.
{A)
Terminal number
indications
(B)
Release holes
Insert a flat-blade screwdriver into these holes to connect and remove the wires.
(C)
Terminal holes
The wires are inserted into these holes.
13
NX-PD/PF/PC/TBX
Applicable Terminal Blocks for Each Unit Model
Unit model
NX-PD1000
NX-PF0630
NX-PF0730
NX-PC@@@@
NX-TBX01
Model
NX-TBC082
NX-TBA082
NX-TBA082
NX-TBA162
NX-TBC162
No. of terminals
8
8
8
16
16
Terminal Blocks
Terminal number
indications
A/B
A/B
A/B
A/B
A/B
Ground terminal
mark
Provided
None
None
None
Provided
Terminal current
capacity
10 A
10 A
10 A
10 A
10 A
Applicable Wires
Using Ferrules
If you use ferrules, attach the twisted wires to them.
Observe the application instructions for your ferrules for the wire stripping length when attaching ferrules.
Always use plated one-pin ferrules. Do not use unplated ferrules or two-pin ferrules.
The applicable ferrules, wires, and crimping tool are given in the following table.
Terminal types
Manufacturer
Ferrule model
Terminals other
than ground
terminals
Applicable wire
(mm2 (AWG))
0.34 (#22)
0.5 (#20)
Crimping tool
Phoenix Contact AI0,34-8
Phoenix Contact (The figure in parentheses is the applicable wire
size.)
AI0,5-8
CRIMPFOX 6 (0.25 to 6 mm2, AWG 24 to 10)
AI0,5-10
AI0,75-8
0.75 (#18)
AI0,75-10
AI1,0-8
1.0 (#18)
AI1,0-10
AI1,5-8
1.5 (#16)
AI1,5-10
Ground terminals
AI2,5-10
2.0 *1
Terminals other Weidmuller
H0.14/12
0.14 (#26)
Weidmueller (The figure in parentheses is the applicable wire size.)
than ground
PZ6 Roto (0.14 to 6 mm2, AWG 26 to 10)
H0.25/12
0.25 (#24)
terminals
H0.34/12
0.34 (#22)
H0.5/14
0.5 (#20)
H0.5/16
H0.75/14
0.75 (#18)
H0.75/16
H1.0/14
1.0 (#18)
H1.0/16
H1.5/14
1.5 (#16)
H1.5/16
*1. Some AWG 14 wires exceed 2.0 mm2 and cannot be used in the screwless clamping terminal block.
When you use any ferrules other than those in the above table, crimp them to the twisted wires so that the following processed dimensions are achieved.
8 to 10 mm
1.6 mm max.
(Terminals other than ground terminals)
2.4 mm max.
(Terminals other than ground terminals)
2.7 mm max.
(Ground terminals)
2.0 mm max.
(Ground terminals)
Using Twisted Wires/Solid Wires
If you use the twisted wires or the solid wires, use the following table to determine the correct wire specifications.
Wire type
Conductor length
Twisted wires
Solid wire
Wire size
(stripping length)
Classification
Current capacity
Plated
Unplated
Plated
Unplated
2 A max.
Possible
Possible
Possible
Possible
Greater than
All terminals except
0.08 to 1.5 mm2
8 to 10 mm
Possible *1 Not
Not
2 A and 4 A or less
AWG28 to 16
ground terminals
Possible
Possible
Possible *1
Not Possible
Greater than 4 A
Ground terminals
--Possible
Possible
Possible *2 Possible *2 2.0 mm2
9 to 10 mm
*1. Secure wires to the screwless clamping terminal block. Refer to the Securing Wires in the USER'S MANUAL for how to secure wires.
*2. With the NX-TB@@@1 Terminal Block, use twisted wires to connect the ground terminal. Do not use a solid wire.
Terminals
Conductor length (stripping length)
<Additional Information> If more than 2 A will flow on the wires, use plated wires or use ferrules.
14
NX-PD/PF/PC/TBX
Dimensions
(Unit: mm)
Additional NX Unit Power Supply Unit, Additional I/O Power Supply Unit, I/O Power Supply
Connection Unit, and Shield Connection Unit
NX-PD1000/NX-PF0@30/NX-PC00@0/NX-TBX01
● Unit Only
14.1
12.0
0.55
1.5
104.5
100
1.5
65.2
71
80.1
● With Cables Connected
100
71
Related Manuals
Man. No
W523
Model
NX-PD1 @@@
NX-PF0 @@@
NX-PC0 @@@
NX-TBX @@@
Manual
NX-series System Unit
User’s Manual
Application
Learning how to use NXseries System Units
Description
The hardware and functions of the NX-series
System Units are described.
15
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2016.4
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2016 All Right Reserved.