ECLIPTEK PART NUMBER DATA SHEET CORPORATION EMRE12H2H-200.000M REGULATORY COMPLIANCE R (Data Sheet downloaded on Jun 28, 2016) 2011/65 + 2015/863 168 SVHC ITEM DESCRIPTION MEMS Clock Oscillators LVDS (DS) 2.5Vdc 6 Pad 5.0mm x 7.0mm Plastic Surface Mount (SMD) 200.000MHz ±50ppm over -40°C to +85°C ELECTRICAL SPECIFICATIONS Nominal Frequency 200.000MHz Frequency Tolerance/Stability ±50ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, 1st Year Aging at 25°C, Reflow, Shock, and Vibration) Aging at 25°C ±1ppm Maximum First Year Supply Voltage 2.5Vdc ±10% Input Current 45mA Typical, 55mA Maximum (Excluding Load Termination Current) Differential Output Error (dVod) 50mVdc Maximum Differential Output Voltage (Vod) 200mVdc Minimum, 350mVdc Typical, 500mVdc Maximum Offset Voltage (Vos) 1.125V Minimum, 1.20V Typical, 1.375V Maximum Rise/Fall Time 500pSec Typical, 600pSec Maximum (Measured over 20% to 80% of waveform) Duty Cycle 50 ±5(%) (Measured at 50% of waveform) Offset Error (dVos) 50mVdc Maximum Load Drive Capability 100 Ohms Between Output and Complementary Output Output Logic Type LVDS Logic Control / Additional Output Output Enable (OE) and Complementary Output Output Control Input Voltage Vih of 70% of Vdd Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of Vdd Maximum to Disable Output and Complementary Output (High Impedance) Output Enable Current 35mA Maximum (OE) Without Load RMS Phase Jitter 0.5pSec Typical, 1pSec Maximum (Fj = 12kHz to 20MHz; Random) Period Jitter (Deterministic) 0.2pSec Typical Period Jitter (Random) 1.0pSec Typical Period Jitter (RMS) 1.4pSec Typical, 1.7pSec Maximum Period Jitter (pk-pk) 15pSec Typical, 20pSec Maximum Start Up Time 10mSec Maximum Storage Temperature Range -55°C to +125°C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS ESD Susceptibility MIL-STD-883, Method 3015, Class 2, HBM 2000V Flammability UL94-V0 Mechanical Shock MIL-STD-883, Method 2002, Condition G, 30,000G Moisture Resistance MIL-STD-883, Method 1004 Moisture Sensitivity Level J-STD-020, MSL 1 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 (Six I/O Pads on bottom of package only) Temperature Cycling MIL-STD-883, Method 1010, Condition B Thermal Shock MIL-STD-883, Method 1011, Condition B Vibration MIL-STD-883, Method 2007, Condition A, 20G www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 1 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 ECLIPTEK PART NUMBER DATA SHEET R CORPORATION EMRE12H2H-200.000M MECHANICAL DIMENSIONS (all dimensions in millimeters) 0.85 ±0.15 5.00 ±0.15 1.20 ±0.10 (x6) 0.08 MAX 7.00 ±0.15 5.08 ±0.10 3 4 2 5 PIN CONNECTION 1 Output Enable (OE) 2 No Connect 3 Case Ground 4 Output 5 Complementary Output 6 Supply Voltage LINE MARKING 1 2.54 TYP 2.60 ±0.15 1 6 1.40 ±0.10 (x6) XXXXX XXXXX=Ecliptek Manufacturing Lot Code Suggested Solder Pad Layout All Dimensions in Millimeters 1.80 (X6) 2.00 (X6) 0.54 (X4) 2.39 Solder Land (X6) All Tolerances are ±0.1 www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 2 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 ECLIPTEK PART NUMBER DATA SHEET R CORPORATION EMRE12H2H-200.000M Q MINUS Q OUTPUT Q & Q OUTPUTS TRI-STATE INPUT OUTPUT WAVEFORM & TIMING DIAGRAM VIH VIL VOH Q VOS HIGH IMPEDANCE STATE VOD Q VOL 80% 0V VOp-p HIGH IMPEDANCE STATE 20% tPLZ Fall Time Rise Time tPZL TW T Duty Cycle (%) = TW/T x 100 www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 3 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 ECLIPTEK PART NUMBER DATA SHEET R CORPORATION EMRE12H2H-200.000M Test Circuit for Tri-State and Complementary Output Frequency Counter Oscilloscope Current Meter Switch 0.01µF (Note 1) Supply Voltage (VDD) 0.1µF (Note 1) Probe 2 (Note 2) Probe 1 (Note 2) 100 Ohms Complementary Output Output Ground Power Supply Voltage Meter Power Supply Tri-State No Connect Note 1: An external 0.01µF ceramic bypass capacitor in parallel with a 0.1µF high frequency ceramic bypass capacitor close (less than 2mm) to the package ground and supply voltage pin is required. Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>500MHz) passive probe is recommended. Note 3: Test circuit PCB traces need to be designed for a characteristic line impedance of 50 ohms. www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 4 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET EMRE12H2H-200.000M ECLIPTEK R CORPORATION Recommended Solder Reflow Methods High Temperature Infrared/Convection TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5°C of actual peak (tp) Ramp-down Rate Time 25°C to Peak Temperature (t) Moisture Sensitivity Level 3°C/Second Maximum 150°C 175°C 200°C 60 - 180 Seconds 3°C/Second Maximum 217°C 60 - 150 Seconds 260°C Maximum for 10 Seconds Maximum 250°C +0/-5°C 20 - 40 Seconds 6°C/Second Maximum 8 Minutes Maximum Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 5 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET EMRE12H2H-200.000M ECLIPTEK R CORPORATION Recommended Solder Reflow Methods Low Temperature Infrared/Convection 240°C TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5°C of actual peak (tp) Ramp-down Rate Time 25°C to Peak Temperature (t) Moisture Sensitivity Level 5°C/Second Maximum N/A 150°C N/A 60 - 120 Seconds 5°C/Second Maximum 150°C 200 Seconds Maximum 240°C Maximum 240°C Maximum 2 Times / 230°C Maximum 1 Time 10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time 5°C/Second Maximum N/A Level 1 Low Temperature Manual Soldering 185°C Maximum for 10 Seconds Maximum, 2 times Maximum. High Temperature Manual Soldering 260°C Maximum for 5 Seconds Maximum, 2 times Maximum. www.ecliptek.com | Specification Subject to Change Without Notice | Revision A 05/11/2012 | Page 6 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200