PANASONIC GRM188B11C104KA01

AN30183A
600mA Synchronous DC-DC Step Down Regulator (1ch)
300mA LDO Regulator (4ch)
Multi Power Supply (High Efficiency Power LSI)
FEATURES
DESCRIPTION
z High-Speed Response DC-DC Step Down Regulator
Circuit that employs Hysteretic System
z DC-DC Step Down Regulator : 1-ch
Input voltage Range VBAT :2.5V to 5.5V
DVDD : 1.7V to 3.0V
Output voltage Range 0.8 V to 2.4 V
Up to 600 mA Output Current
AN30183A is a multi power supply LSI which has HighSpeed Response DC-DC Step Down Regulators (1-ch)
and LDO Regulators (4-ch).
By this DC-DC system, when load current charges
suddenly, it responds at high speed and minimizes the
changes of output voltage.
Since it is possible to use capacitors with small
capacitance and it is unnecessary to add external parts
for system phase compensation, this IC realizes
downsizing of set and reducing in the number of external
parts.
The output DC of each power supply is variable by I2C
control.
z LDO Regulator : 4-ch
Input voltage Range VBAT :2.5V to 5.5V
DVDD : 1.7V to 3.0V
Output voltage Range 1.0 V to 3.3 V
Up to 300 mA Output Current
z I2C control (2-slave address selectable)
z 20 pin Wafer Level Chip Size Package (WLCSP)
(Size : 1.56 mm × 2.06 mm, 0.4 mm Pitch)
APPLICATIONS
Mobile phone, Portable appliance, etc
SIMPLIFIED APPLICATION
EFFICIENCY CURVE
DDVBAT1
DVDD
VIN2
VB
4.7µF
4.7µF
100
SDA
SCL
ASEL
LX1
FB1
DDGND1
REGCNT
VLDO3
AN30183A
90
DCDCOUT1
1µH
80
4.7µF
VLDO1
1µF
1µF
AN30183A DCDC1 Efficiency
4.7µF
Efficiency [%]
0.1µF
1µF
VLDO4
VLDO2
1µF
60
50
Vout=0.8V
40
Vout=1.2V
30
Vout=1.8V
20
Vout=2.4V
10
VREG REF RESETLDO1ON AGND
1µF
70
0
1µF
1
10
100
1000
Load Current [mA]
Notes) This application circuit is an example. The operation
of mass production set is not guaranteed. You should
perform enough evaluation and verification on the
design of mass production set. You are fully
responsible for the incorporation of the above
application circuit and information in the design of
your equipment.
Publication date: October 2012
Condition )
DDVBAT1 = DDVBAT2 = VB = VIN2 = 3.7V
Lo = 1.0 µH, Cout = 4.7 µF
1
Ver. AEB
AN30183A
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Notes
VB,VIN2,DDVBAT1
6.0
V
*1
DVDD
3.6
V
*1
IIN
—
A
*1
Operating free-air temperature
Topr
– 30 to + 85
°C
*2
Operating junction temperature
Tj
– 30 to + 150
°C
*2
Tstg
– 55 to + 150
°C
*2
RESET,LDO1ON,FB1,
REGCNT
– 0.3 to VVBAT + 0.3
V
*1
*3
SCL,SDA,ASEL
– 0.3 to DVDD + 0.3
V
*1
*3
LX1,VREG,REF,SDA
LDO1,LDO2,LDO3,LDO4
– 0.3 to VVBAT + 0.3
V
*1
*3
HBM (Human Body Model)
2
kV
—
Supply voltage
Output Current
Storage temperature
Input Voltage Range
Output Voltage Range
ESD
Notes) Do not apply external currents and voltages to any pin not specifically mentioned.
This product may sustain permanent damage if subjected to conditions higher than the above stated absolute maximum rating.
This rating is the maximum rating and device operating at this range is not guaranteeable as it is higher than our stated
recommended operating range. When subjected under the absolute maximum rating for a long time, the reliability of the product
may be affected.
*1:The values under the condition not exceeding the above absolute maximum ratings and the power dissipation.
*2:Except for the power dissipation, operating ambient temperature, and storage temperature, all ratings are for Ta = 25 °C.
*3:VVBAT is voltage for DDVBAT1 = VB = VIN2, (VVBA + 0.3) V must not be exceeded 6 V.
VDVDD is voltage for DVDD, (VDVDD + 0.3) V must not be exceeded 3.6 V.
POWER DISSIPATION RATING
θJA
PD ( Ta = 25 °C)
PD ( Ta = 85 °C )
Notes
359.0 °C / W
0.348 W
0.181 W
*1
PACKAGE
20 pin Wafer level chip size Package
(WLCSP Type)
Note). For the actual usage, please refer to the PD-Ta characteristics diagram in the package specification, follow the power supply
voltage, load and ambient temperature conditions to ensure that there is enough margin and the thermal design does not
exceed the allowable value.
*1:Glass Epoxy Substrate ( 4 Layers ) [ Glass-Epoxy: 50 X 50 X 0.8 t ( mm ) ]
Die Pad Exposed , Soldered.
CAUTION
Although this has limited built-in ESD protection circuit, but permanent damage may occur on it.
Therefore, proper ESD precautions are recommended to avoid electrostatic damage to the MOS gates
2
Ver. AEB
AN30183A
RECOMMENDED OPERATING CONDITIONS
Parameter
Supply voltage range
Input Voltage Range
Output Voltage Rang
Pin Name
Min.
Typ.
Max.
Unit
Notes
VB
2.5
3.7
5.5
V
*1
VIN2
2.5
3.7
5.5
V
*1
DDVBAT1
2.5
3.7
5.5
V
*1
DVDD
1.7
1.85
3.0
V
*1
RESET
– 0.3
—
VVBAT + 0.3
V
*2
LDO1ON
– 0.3
—
VVBAT + 0.3
V
*2
REGCNT
– 0.3
—
VVBAT + 0.3
V
*2
FB1
– 0.3
—
VVBAT + 0.3
V
*2
SCL
– 0.3
—
DVDD + 0.3
V
*2
SDA
– 0.3
—
DVDD + 0.3
V
*2
ASEL
– 0.3
—
DVDD + 0.3
V
*2
LX1
– 0.3
—
VVBAT + 0.3
V
*2
VREG
– 0.3
—
VVBAT + 0.3
V
*2
REF
– 0.3
—
VVBAT + 0.3
V
*2
SDA
– 0.3
—
DVDD + 0.3
V
*2
VLDO1
– 0.3
—
VVBAT + 0.3
V
*2
VLDO2
– 0.3
—
VVBAT + 0.3
V
*2
VLDO3
– 0.3
—
VVBAT + 0.3
V
*2
VLDO4
– 0.3
—
VVBAT + 0.3
V
*2
Note) Do not apply external currents and voltages to any pin not specifically mentioned.
Voltage values, unless otherwise specified, are with respect to GND. GND is voltage for AGND = DDGND1
VVBAT is voltage for DDVBAT1 = VB = VIN2.
*1 : The values under the condition not exceeding the above absolute maximum ratings and the power dissipation.
*2 : (VVBAT + 0.3) V must not be exceeded 6 V. (DVDD + 0.3) V must not be exceeded 3.6 V.
3
Ver. AEB
AN30183A
ELECRTRICAL CHARACTERISTICS
VVBAT(DDVBAT1 = VB = VIN2) = 3.7V, DVDD = 1.85V
DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Limits
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Notes
Consumption current
Consumption current 1 on active
IBAT_1 only LDO1 (PS mode) ON
—
10
20
μA
—
Consumption current 2 on active
IBAT_2 DCDC1, LDO1-4 = ON
—
240
400
μA
—
Static consumption current
IBAT_3
—
0.1
1.0
μA
—
DCDC1, LDO1-4 = OFF
RESET = “L”
4
Ver. AEB
AN30183A
ELECRTRICAL CHARACTERISTICS (Continued)
VVBAT(DDVBAT1 = VB = VIN2) = 3.7V, DVDD = 1.85V
DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Limits
Parameter
Symbol
Conditions
Unit
Notes
1.897
V
—
Min
Typ
Max
1.803
1.850
LDO1 – 4 ( Normal Mode ) - (LDO Regulator)
ILDO = – 150 mA
Vout = 1.85 V setting
Output voltage
VLDO
Output current
ILDO
—
300
—
—
mA
—
Load regulation
DVLDO
Δ ILDO = – 10 μA → – 150 mA
–5
20
50
mV
—
Line regulation
VLDOLR
VB = 3.1 V → 4.5 V
ILDO = – 150 mA
Vout = 1.85 V setting
– 10
0
10
mV
—
Short-circuit current
ISTLDO
VB = 3.7 V
VLDO = 0 V
35
100
255
mA
—
1.803
1.850
1.897
V
—
10
—
—
mA
—
–5
20
50
mV
—
– 25
0
25
mV
—
LDO1 – 4 ( Power Save Mode ) - (LDO Regulator)
ILDO = – 5 mA
Vout = 1.85 V setting
Output voltage
VLDOPS
Output current
ILDOPS
Load regulation
DVLDOPS
Line regulation
VB = 3.1 V → 4.5 V
VLDOLRPS ILDO = – 5 mA
Vout = 1.85 V setting
—
Δ ILDO = – 10 μA → – 5 mA
5
Ver. AEB
AN30183A
ELECRTRICAL CHARACTERISTICS (Continued)
VVBAT(DDVBAT1= VB = VIN2) = 3.7V, DVDD = 1.85V
DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Limits
Parameter
Symbol
Conditions
Unit
Notes
1.230
V
—
Min
Typ
Max
1.170
1.200
DCDC1 (DC-DC Step Down Regulator)
IDCDC1 = – 300 mA
Vout = 1.2 V setting
Output voltage
VDCDC1
Output current
IDCDC1
—
600
—
—
mA
—
Load regulation
DVDCDC1
Δ IDCDC1 = – 10 μA → – 500 mA
Vout = 1.2 V setting
—
25
45
mV
—
Line regulation
DDVBAT1 = 3.1 V → 4.5 V
VDCDC1LR IDCDC1 = – 300 mA
Vout = 1.2 V setting
—
4
13
mV
—
Oscillation frequency
ISTDCDC1
2
3
4
MHz
—
IDCDC1 = – 300 mA (CCM)
I/O characteristics of control terminal (RESET, LDO1ON, REGCNT)
Low input voltage
VIL1
Voltage recognized as low level
—
—
0.45
V
—
High input voltage
VIH1
Voltage recognized as high level
1.2
—
—
V
—
Input pull-down resistance
PDR1
1
3
6
MΩ
—
—
I/O characteristics of control terminal (ASEL)
Low input voltage
VIL2
Voltage recognized as low level
—
—
VDVDD
× 0.3
V
—
High input voltage
VIH2
Voltage recognized as high level
VDVDD
× 0.7
—
—
V
—
6
Ver. AEB
AN30183A
APPLICATION INFORMATION
REFERENCE VALUES FOR DESIGN
VVBAT(DDVBAT1 = VB = VIN2) = 3.7V, DVDD = 1.85V
Ta = 25 °C ± 2 °C unless otherwise noted.
Reference values
Parameter
Symbol
Conditions
Min
Typ
Max
0.3 ×
VDVDD
Unit
Notes
V
*1
*2
V
*1
*2
I2C Bus (Internal I/O Stage Characteristics)
Low-level input voltage
VIL1
Voltage which recognized that
SDA and SCL are Low-level
– 0.5
—
High-level input voltage
VIH1
Voltage which recognized that
SDA and SCL are High-level
0.7 ×
VDVDD
—
VDVDD
max
+ 0.5
Low-level output voltage 1
VOL1
VDVDD > 2 V
SDA(sink current) = 3 mA
0
—
0.4
V
*2
Low-level output voltage 2
VOL2
VDVDD < 2 V
SDA(sink current) = 3 mA
0
—
0.2 ×
VDVDD
V
*2
Input current each I/O pin
IL
– 10
—
10
μA
*2
0
—
400
kHz
*2
SCL clock frequency
SCL, SDA =
0.1 × VDVDDmax to
0.9 × VDVDDmax
FOSC
—
Notes) *1 : The input threshold voltage of I2C bus (Vth) is linked to VDVDD.
In case the pull-up voltage is not VDVDD, the threshold voltage (Vth) is fixed to ((VDVDD / 2) ± (Schmitt width) / 2 ) and High-level,
Low-level of input voltage are not specified.
In this case, pay attention to Low-level (max.) value (VILmax).
It is recommended that the pull-up voltage of I2C bus is set to the I2C bus I/O stage supply voltage (VDVDD).
*2 :Checked by design, not production tested.
7
Ver. AEB
AN30183A
APPLICATION INFORMATION (Continued)
REFERENCE VALUES FOR DESIGN
VVBAT(DDVBAT1 = VB = VIN2) = 3.1V to 4.5V, VDVDD = 1.85V , DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Reference values
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Notes
LDO1 – 4 ( Normal Mode ) - (LDO Regulator)
VLDO
ILDO = – 150 mA
Vout = 1.85 V setting
1.803
1.850
1.897
V
*2
Consumption current on active
IREGLDO
Normal mode
VB > Vout + 0.1 V or
VIN2 > Vout + 0.1 V
25
50
75
μA
*2
I/O voltage difference
VSATLDO
ILDO = – 300 mA
0.3
—
—
V
*2
Ripple rejection
VLDORR
ΔVB = 3.7 V ± 0.15 V
ILDO = – 150 mA
fvin = 100 Hz to 10 kHz
—
– 60
– 40
dB
*2
Discharge resistance
RDISLDO
—
50
100
200
kΩ
*2
Load change characteristic
LTRLDO
ILDO = – 10 μA ↔ – 100 mA
—
30
150
mV
*2
1.803
1.850
1.897
V
*2
1
3
5
μA
*2
Output voltage
LDO1 – 4 ( Power Save Mode ) - (LDO Regulator)
Output voltage
VLDOPS
ILDO = – 5 mA
Vout = 1.85 V setting
Consumption current on active
Power Save mode
IREGLDOPS VB > Vout + 0.1 V or
VIN2 > Vout + 0.1 V
Ripple rejection
VLDOPSRR
ΔVB = 3.7 V ± 0.15 V
ILDO = – 5 mA
fvin = 100 Hz to 10 kHz
—
– 10
–5
dB
*2
Short-circuit current
ISTLDOPS
VB = 3.7 V
VLDO = 0 V
5
20
40
mA
*2
Notes)
*2 :Checked by design, not production tested.
8
Ver. AEB
AN30183A
APPLICATION INFORMATION (Continued)
REFERENCE VALUES FOR DESIGN
VVBAT(DDVBAT1 = VB = VIN2) = 3.1V to 4.5V, DVDD = 1.85V , DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Reference values
Parameter
Symbol
Conditions
Unit
Notes
1.230
V
*2
25
40
μA
*2
—
1.0
1.2
A
*2
Min
Typ
Max
1.170
1.200
10
DCDC1 (DC-DC Step Down Regulator)
Output Voltage
VDCDC1
IDCDC1 = – 300 mA
Vout = 1.2 V setting
Consumption current on active
IREGDCCD1 IDCDC1 = 0 mA
Output over current limit
ILIMDCDC1
Efficiency 1
DDVBAT1 = 3.4 V
EFFDCDC11 VDCDC1 = 2.4 V
IDCDC1 = – 150 mA
85
90
—
%
*2
Efficiency 2
DDVBAT1 = 3.7 V
EFFDCDC12 VDCDC1 = 1.2 V
IDCDC1 = – 150 mA
75
80
—
%
*2
DDVBAT1 = 5.5 V
DCDC1 = Disable
VLX1 = 0 V or 5.5 V
–1
0
1
μA
*2
0.5
1.0
2.0
kΩ
*2
LX leak current
Discharge resistance
Notes)
ILXL1
From FB1 × 100% to FB1 ×
70%
VB = 3.7 V
RDISDCDC1
—
*2 :Checked by design, not production tested.
9
Ver. AEB
AN30183A
APPLICATION INFORMATION (Continued)
REFERENCE VALUES FOR DESIGN
VVBAT(DDVBAT1 = VB = VIN2) = 3.1V to 4.5V, DVDD = 1.85V , DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Reference values
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Notes
I2C bus (Internal I/O stage characteristics)
Hysteresis of Schmitt trigger
input 1
Vhys1
VIO > 2 V,
Hysteresis 1 of SDA, SCL
0.05 ×
VDVDD
—
—
V
*2
Hysteresis of Schmitt trigger
input 2
Vhys2
VIO < 2 V,
Hysteresis 2 of SDA, SCL
0.1 ×
VDVDD
—
—
V
*2
Output fall time from VIHmin to VILmax
Tof
Bus capacitance : 10 pF to
400 pF
IP ≤ 6 mA (VOLmax = 0.6 V)
IP : Max. sink current
20 +
0.1 × Cb
—
250
ns
*2
Pulse width of spikes which must
be suppressed by the input filter
Tsp
—
0
—
50
ns
*2
Ci
—
—
—
10
pF
*2
0.6
—
—
μs
*2
Capacitance for each I/O pin
I2 C
bus (Bus line specifications)
The first clock pulse is
generated after tHD:STA.
Hold time
(repeated) START condition
tHD:STA
Low period of the SCL clock
tLOW
—
1.3
—
—
μs
*2
High period of the SCL clock
tHIGH
—
0.6
—
—
μs
*2
Set-up time for a repeat START
condition
tSU:STA
—
0.6
—
—
μs
*2
Data hold time
tHD:DAT
—
0
—
0.9
μs
*2
Data set-up time
tSU:DAT
—
100
—
—
ns
*2
Rise time of both SDA
and SCL signals
tr
—
20 +
0.1 × Cb
—
300
ns
*2
Fall time of both SDA
and SCL signals
tf
—
20 +
0.1 × Cb
—
300
ns
*2
Set-up time of STOP condition
tSU:STO
—
0.6
—
—
μs
*2
Bus free time between STOP
and START condition
tBUF
—
1.3
—
—
μs
*2
Notes)
*2 :Checked by design, not production tested.
10
Ver. AEB
AN30183A
APPLICATION INFORMATION (Continued)
REFERENCE VALUES FOR DESIGN
VVBAT(DDVBAT1 = VB = VIN2) = 3.1V to 4.5V, DVDD = 1.85V , DC-DC : Co = 4.7 µF, Lo = 1 µH / LDO : Co =1.0 µF
Ta = 25 °C ± 2 °C unless otherwise noted.
Reference values
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Notes
I2C bus (Bus line specifications) (continued)
Capacitive load for each bus line
Cb
—
—
—
400
pF
*2
*3
Noise margin at the Low-level for
each connected device
VnL
—
0.1 ×
VDVDD
—
—
V
*2
*3
Noise margin at the High-level for
each connected device
VnH
—
0.2 ×
VDVDD
—
—
V
*2
*3
—
8
17
μA
*2
Consumption current
DDVBAT1 = VB = VIN2
= 3.7 V
IBAT_4
DCDC1, LDO1 to 4 = OFF
RESET= “H”
Static consumption current 2
Notes)
*2 :Checked by design, not production tested.
*3 :The timing of Fast-mode devices in I2C-bus is specified as the following.
All values referred to VIHmin and VILmax level.
SDA
tf
tLOW
tSU;DAT
tr
tf
tHD;STA
tSP
tr
tBUF
SCL
S
tHD;STA
tHD;DAT
tHIGH
tSU;STA
Sr
tSU;STO
P
S
S : START condition
Sr : Repeat START condition
P : STOP condition
Notes)
*2 :Checked by design, not production tested.
11
Ver. AEB
AN30183A
PIN CONFIGURATION
TOP VIEW
D
LX1
DD
GND1
SDA
SCL
RESET
C
DD
VBAT1
FB1
AGND
REG
CNT
REF
B
VLDO1
VREG
ASEL
VBAT2
DVDD
VLDO4
A
VB
VLDO2
VBON
ON
VLDO3
VIN2
5
4
3
2
1
LDO1
PIN FUNCTIONS
Pin No.
Pin name
Type
Power Supply
Description
A1
VIN2
A2
VLDO3
A3
LDO1ON
A4
VLDO2
A5
VB
B1
VLDO4
Output
B2
DVDD
Power Supply
Power supply for Logic
B3
ASEL
Input
I2C slave address select
B4
VREG
Output
Reference output
B5
VLDO1
Output
LDO1 output
C1
REF
Output
Reference output
C2
REGCNT
C3
AGND
C4
FB1
C5
DDVBAT1
D1
RESET
Input
Reset input for Logic
D2
SCL
Input
I2C clock input
D3
SDA
Input/Output
D4
DDGND1
Ground
GND
D5
LX1
Output
DCDC1 switching
Output
Input
Output
Power Supply
Input
Ground
Input
Power Supply
Input for LDO3 and LDO4
LDO3 output
LDO1 ON/OFF control
LDO2 output
Input for LDO1, LDO2 and other VB
LDO4 output
Control to select power setting
GND
DCDC1 voltage feedback
DCDC1 input
I2C data input/output
Notes) Concerning detail about pin description, please refer to OPERATION and APPLICATION INFORMATION section.
12
Ver. AEB
AN30183A
FUNCTIONAL BLOCK DIAGRAM
DVDD
C5
B2
DCDC1
0.8 V to 2.4 V / 600 mA(min)
SDA
SCL
ASEL
REGCNT
D3
D2
IC
I/F
2
B3
C2
D4
C4
DVDD
→VB
DDVBAT1
D5 LX1
DDGND1
FB1
VB→DVDD
3 MΩ
RESET
D1
VB→DVDD
DVDD
3 MΩ
VB
DVDD
DET
A5
LDO1
1.0 to 3.3 V / 300 mA(min)
LDO2
1.0 to 3.3 V / 300 mA(min)
B5
A4
VB
VLDO1
VLDO2
VB
TSD
VB
LDO1ON
A3
3 MΩ
REF
C1
A1
LDO3
REF
1.0 to 3.3 V / 300 mA (min)
LDO4
VREG
B4
1.0 to 3.3 V / 300 mA (min)
A2
B1
VIN2
VLDO3
VLDO4
VREG
AGND C3
Notes) • This application circuit is an example. The operation of mass production set is not guaranteed.
You should perform enough evaluation and verification on the design of mass production set.
You are fully responsible for the incorporation of the above application circuit and information
in the design of your equipment.
• This block diagram is for explaining functions. Part of the block diagram may be omitted, or it may be simplified.
13
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES
(1) Output Ripple Voltage of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V , L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , Iout = 0mA
Vout
LX1
DC-DC1 , Iout = 100mA
Vout
LX1
DC-DC1 , Iout = 600mA
Vout
LX1
14
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(2) Load Transient of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V , L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , Iout = 10μA to 500mA
(ΔT=500mA/usec)
Vout
Iout
DC-DC1 , Iout = 500mA to 10μA
(ΔT=500mA/usec)
Vout
Iout
15
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(3) Efficiency of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V , L1 = 1 µH , CDCDCOUT1 = 4.7 µF
AN30183A DC-DC1 Efficiency
100
90
Efficiency [%]
80
70
60
Vout=0.8V
50
Vout=1.2V
40
Vout=1.8V
30
Vout=2.4V
20
10
0
1
10
100
1000
Load Current [mA]
16
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(4) Load Regulation of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V , L1 = 1 µH , CDCDCOUT1 = 4.7 µF
Load Regulation of DC-DC1
1.4
VDCDCOUT1 [V]
1.35
1.3
1.25
1.2
1.15
1.1
1.05
1
0
100
200
300
400
500
600
Load Current [mA]
17
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(5) Line Regulation of DC-DC1
Iout = 300mA, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF , VIN = 2.4V to 5.5V
Line Regulation of DC-DC1
1.4
DCDCOUT1 [V]
1.35
1.3
1.25
1.2
1.15
1.1
1.05
1
2
2.5
3
3.5
4
4.5
5
5.5
6
VIN [V]
18
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(6) Start Up & Shut Down of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , RDCDCOUT1 = No Load
Start Up
VDCDCOUT1
I2C Signal
DC-DC1 , RDCDCOUT1 = No Load
Shut Down
VDCDCOUT1
I2C Signal
19
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(7) Start Up & Shut Down of DC-DC1 (Continued)
VIN = 3.7 V, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , RDCDCOUT1 = 4Ω
Start Up
VDCDCOUT1
I2C Signal
DC-DC1 , RDCDCOUT1 = 4Ω
Shut Down
VDCDCOUT1
I2C Signal
20
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(8) Short Protection of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF
IOUT
VOUT
LX
21
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(9) Thermal Performance of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V, ILoad = 600mA , L1 = 1 µH , CDCDCOUT1 = 4.7 µF
22
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(10) Frequency of DC-DC1
VIN = 3.7 V, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , Iout = 0mA
Vout
LX1
DC-DC1 , Iout = 300mA
Vout
LX1
DC-DC1 , Iout = 600mA
Vout
LX1
23
Ver. AEB
AN30183A
TYPICAL CHARACTERISTICS CURVES (Continued)
(11) Frequency of DC-DC1 (Continued)
IOUT = 300mA, DC-DC1_Vout = 1.2 V, L1 = 1 µH , CDCDCOUT1 = 4.7 µF
DC-DC1 , VIN = 2.5V
Vout
LX1
DC-DC1 , VIN = 3.7V
Vout
LX1
DC-DC1 , VIN = 5.5V
Vout
LX1
24
Ver. AEB
AN30183A
OPERATION
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
1. I2C-bus Interface
a.) Basic Rules
d.) Data format
This IC, I2C-bus, is designed to correspond to the
Standard-mode (100 kbps) and Fast-mode(400 kbps)
devices in the version 2.1 of NXP's specification.
However, it does not correspond to the HS-mode (to 3.4
Mbps). This IC will operate as a slave device in the I2Cbus system. This IC will not operate as a master device.
The program operation check of this IC has not been
conducted on the multi-master bus system and the mixspeed bus system, yet. The connected confirmation of
this IC to the CBUS receiver also has not been checked.
Please confirm with our company if the IC will be used in
these mode systems. The I2C is the brand of NXP.
Slave Address
Pin ASEL A6
Low
1
High
1
A4
1
1
A3
0
0
A2
0
0
A1
1
1
A0 R/W
0
x
1
x
Hex
6Eh
6Fh
Write mode
S Slave Address W A Sub Address A
Start
Condition
b.) START and STOP conditions
Data Byte
A P
Stop
Condition
Ack
Write mode : 0
Read mode
A High to Low transition on the SDA line while SCL is
High is one such unique case. This situation indicates
START condition. A Low to High transition on the SDA
line while SCL is High defines STOP condition.
START and STOP conditions are always generated by
the master. After START condition occur, the bus will be
busy. The bus is considered to be free again a certain
time after the STOP condition.
START condition
A5
1
1
d1.) When Sub address is not specified
When data is read without assigning sub-address, it is
possible to read the value of sub-address specified in
Write mode immediately before.
S
Slave Address
Start
Condition
STOP condition
R A
Data byte
A P
Ack
Read mode : 1
Stop
condition
Ex) When writing data into address and reading data
from "01 h".
SDA
Write
S
Slave
Address
0 A
Read
S
Slave
Address
1 A
Sub Address
A
01h
Data Byte
A P
SCL
Every byte put on the SDA line must be 8-bits long. The
number of bytes that can be transmitted per transfer is
unrestricted. Each byte has to be followed by an
acknowledge bit. Data is transferred with the most
significant bit (MSB) first.
MSB
S
SCL or
Sr
1
acknowledgement
signal from slave
2
START or
repeated START
condition
7
8
9
ACK
acknowledgement
signal from receiver
1
2 3–8 9
A P
d2.) When Sub address is specified
S
P
SDA
Data Byte
Slave
Sub
Slave
0A
AS
1 A Data Byte A P
Address
Address
Address
Stop
Ack
Ack
Condition
Repeated
Start
Read Mode : 1
Condition
Acknowledge Bit
Write Mode : 0
Start
Condition
Sr
Sr
or
P
ACK
STOP or
repeated START
condition
25
Sub-address should be assigned first.
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
2. Register map
Sub
R/W
Address
00h
R/W
Register
Name
Data
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
—
—
LD4ON
LD3ON
LD2ON
LD1ON
—
DD1ON
Default
0
0
0
0
0
0
0
0
CNT
Name
01h
R/W
—
Default
1
1
Name
02h
R/W
04h
05h
06h
R/W
R/W
R/W
0
1
0
VL2[3:0]
0
0
Name
R/W
1
0
0
0
1
VL1[3:0]
DAC2
Default
03h
VDC1[3:0]
DAC1
0
0
1
0
VL4[3:0]
VL3[3:0]
DAC3
Default
1
1
0
0
1
0
1
0
Name
GPLD4
GPLD3
GPLD2
—
GPDD
—
—
GPEN
Default
1
1
1
1
1
0
0
0
Name
—
—
—
—
LD4PS
LD3PS
LD2PS
LD1PS
Default
—
—
0
0
0
0
0
0
Name
—
—
—
—
—
—
—
LDO1EN
SEL
Default
—
—
—
—
—
—
—
1
—
—
LDO4
LDO3
LDO2
LDO1
—
DCDC1
—
—
2.8V
2.6V
1.0V
1.85V
—
1.2V
GROUP
PSCNT
ENSEL
Default Voltage
26
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
00h
R/W
Register
Name
Data
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
—
—
LD4ON
LD3ON
LD2ON
LD1ON
—
DD1ON
Default
0
0
0
0
0
0
0
0
CNT
D5 : LDO4 ON/OFF select register
[0] : OFF (default)
[1] : ON
D4 : LDO3 ON/OFF select register
[0] : OFF (default)
[1] : ON
D3 : LDO2 ON/OFF select register
[0] : OFF (default)
[1] : ON
D2 : LDO1 ON/OFF select register
[0] : OFF (default)
[1] : ON
D0 : DCDC1 ON/OFF select register
[0] : OFF (default)
[1] : ON
27
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
Register
Name
Data
Bit
D7
D6
Name
01h
R/W
D5
D4
D3
—
D2
D1
D0
VDC1[3:0]
DAC1
Default
1
1
1
0
1
0
0
0
D3-0 : DCDC1 Register for output voltage setup
VDC1[3:0]
D7
D6
D5
D4
Output voltage
[V]
0
0
0
0
0.80
0
0
0
1
0.85
0
0
1
0
0.90
0
0
1
1
0.95
0
1
0
0
1.00
0
1
0
1
1.05
0
1
1
0
1.10
0
1
1
1
1.15
1
0
0
0
1.20 (Default)
1
0
0
1
1.30
1
0
1
0
1.40
1
0
1
1
1.50
1
1
0
0
1.65
1
1
0
1
1.80
1
1
1
0
1.85
1
1
1
1
2.40
28
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
Register
Name
Data
Bit
D7
D6
Name
02h
R/W
D5
D4
D3
D2
VL2[3:0]
D1
D0
VL1[3:0]
DAC2
Default
0
0
0
D7-4 : LDO2 Register for output voltage setup
VL2[3:0]
0
1
0
0
1
D3-0 : LDO1 Register for output voltage setup
VL1[3:0]
D3
D2
D1
D0
Output voltage
[V]
D7
D6
D5
D4
Output voltage
[V]
0
0
0
0
1.00 (Default)
0
0
0
0
1.00
0
0
0
1
1.10
0
0
0
1
1.10
0
0
1
0
1.20
0
0
1
0
1.20
0
0
1
1
1.30
0
0
1
1
1.30
0
1
0
0
1.40
0
1
0
0
1.40
0
1
0
1
1.50
0
1
0
1
1.50
0
1
1
0
1.60
0
1
1
0
1.60
0
1
1
1
1.70
0
1
1
1
1.70
1
0
0
0
1.80
1
0
0
0
1.80
1
0
0
1
1.85
1
0
0
1
1.85 (Default)
1
0
1
0
2.60
1
0
1
0
1.90
1
0
1
1
2.70
1
0
1
1
2.70
1
1
0
0
2.80
1
1
0
0
2.80
1
1
0
1
2.85
1
1
0
1
2.85
1
1
1
0
3.00
1
1
1
0
3.00
1
1
1
1
3.30
1
1
1
1
3.30
29
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
Register
Name
Data
Bit
D7
D6
Name
03h
R/W
D5
D4
D3
D2
VL4[3:0]
D1
D0
VL3[3:0]
DAC3
Default
1
1
0
D7-4 : LDO4 Register for output voltage setup
VL4[3:0]
0
0
1
1
0
D3-0 : LDO3 Register for output voltage setup
VL3[3:0]
D7
D6
D5
D4
Output voltage
[V]
0
0
0
0
1.00
0
0
0
0
1.00
0
0
0
1
1.10
0
0
0
1
1.10
0
0
1
0
1.20
0
0
1
0
1.20
0
0
1
1
1.30
0
0
1
1
1.30
0
1
0
0
1.40
0
1
0
0
1.40
0
1
0
1
1.50
0
1
0
1
1.50
0
1
1
0
1.60
0
1
1
0
1.60
0
1
1
1
1.70
0
1
1
1
1.70
1
0
0
0
1.80
1
0
0
0
1.80
1
0
0
1
1.85
1
0
0
1
1.85
1
0
1
0
2.60
1
0
1
0
2.60 (Default)
1
0
1
1
2.70
1
0
1
1
2.70
1
1
0
0
2.80 (Default)
1
1
0
0
2.80
1
1
0
1
2.85
1
1
0
1
2.85
1
1
1
0
3.00
1
1
1
0
3.00
1
1
1
1
3.30
1
1
1
1
3.30
30
D3
D2
D1
D0
Output voltage
[V]
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
04h
R/W
Register
Name
Data
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
GPLD4
GPLD3
GPLD2
—
GPDD
—
—
GPEN
Default
1
1
1
1
1
0
0
0
GROUP
* Please set it to normal mode when LDO starts.
D7 : External pin ON/OFF control for LDO4 select register
[0] : I2C control
[1] : External pin control (default)
D6 : External pin ON/OFF control for LDO3 select register
[0] : I2C control
[1] : External pin control (default)
D5 : External pin ON/OFF control for LDO2 select register
[0] : I2C control
[1] : External pin control (default)
D3 : External pin ON/OFF control for DCDC1 select register
[0] : I2C control
[1] : External pin control (default)
D0 : External pin control permit register
[0] : External pin control valid (default)
[1] : External pin control invalid
31
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
<REGCNT pin control – set up method>
(1) REGCNT Pin Control setup (excluding LDO1)
z Initial setup
1) Select the LDO/DCDC to be controlled by REGCNT
(Address:04h Single Bit from D7-5, D3 should be set to “H”)
Set D0 to “H”
2) Set the LDO/DCDC Startup register mentioned above in ① to “H”
(To control LDO1 set Address:00h D2:LDO1ON to “H”)
Set the LDO to be controlled to Normal Mode (Address:05h Default)
z Startup Control
3) LDO/DCDC selected in 1) above will startup when REGCNT is set to “H”
Power Save Mode for the LDO can be controlled by the I2C
When the Startup register mentioned in 2) above (Address:00h) is set to “L”, the LDO/DCDC will turn off.
4) The Startup for LDO/DCDC not selected in 1) can also be controlled by the I2C
5) To turn off the LDO mentioned in 1) above, set the REGCNT to “L”.
When the LDO is turned OFF in the Power Save Mode, reset Address:05h to Normal Mode before turning on
the LDO using the REGCNT pin.
z Example Using the REGCNT pin to control LDO2 and LDO3
1)
2)
3)
4)
5)
ADDRESS 04h：DATA 61h
ADDRESS 00h：DATA 18h
Set REGCNT pin “L” to “H” : LDO2,3 Startup
Use I2C to control the Output Voltage and Power Save Mode settings
To stop LDO2 and LDO3, Set REGCNT from “H” to “L”
(2) Control using the I2C only
z Initial Setup
No special settings required after RESET
(ADDRESS 04h Bit D0 set to “L)
z (Startup control)
The REGCNT pin should be set to “L” when using the I2C for LDO/DCDC Startup/Shutdown, Power Save Mode
and Output Voltage Setup.
32
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
05h
R/W
Register
Name
Data
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
—
—
—
—
LD4PS
LD3PS
LD2PS
LD1PS
Default
—
—
0
0
0
0
0
0
PSCNT
*Please set it to normal mode when LDO starts.
D3 : LDO4 Power save mode select register
[0] : Normal mode (default)
[1] : Power save mode
D2 : LDO3 Power save mode select register
[0] : Normal mode (default)
[1] : Power save mode
D1 : LDO2 Power save mode select register
[0] : Normal mode (default)
[1] : Power save mode
D0 : LDO1 Power save mode select register
[0] : Normal mode (default)
[1] : Power save mode
33
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
3. Register map details
Sub
R/W
Address
06h
R/W
Register
Name
Data
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
—
—
—
—
—
—
—
LDO1EN
SEL
Default
—
—
—
—
—
—
—
1
ENSEL
D0 : LDO1ENSEL
[0] : LDO1ON control invalid
[1] : LDO1ON control valid (default)
34
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
4. Timing Chart (Sequence – 1 (DVDD input externally))
VBAT
(External input signal)
REF
(IC output signal)
1.24 V
2.4 V
VREG
(IC output signal)
2.2 V
2.1 V
REGW
(IC inner signal)
DVDD
(External input signal)
1.5 V
1.4 V
DVDD
DET
(IC inner signal)
I2C acceptance starts
RESET
(External input signal)
I2C acceptance stops
DVDD_DET:High and RESET:High
= I2C acceptance ON
DVDD_DET:Low and RESET:Low
= I2C acceptance OFF
All registers are initialized
(LDO and DCDC are turned off)
LDO1ON
(External input signal)
at LDO-start
OSC
(IC inner signal)
VLDO1
(IC output signal)
PS⇔NM
Pin LDO1 stops
Pin LDO1 starts
LDO1 starts in NM mode
VLDO
2/3/4
(IC output signal)
DCDC1
(IC output signal)
NM
PS
at DCDC-start
PS⇔NM
I2C stops
I2C starts
NM
NM
PS
I2C input
I2C starts
I2C input
NM
@ 150 μs
NM
LDO* stop is possible even in PS mode
I2C stops
PS
NM
I2C stops
I2C starts
35
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
4. Timing Chart (Sequence – 2 (LDO1ON = fixed VBAT))
VBAT
(External input signal)
1.2 V
0.45 V
REF
(IC output signal)
1.24 V
VREG
(IC output signal)
2.4 V
2.2 V
2.1 V
REGW
(IC inner signal)
DVDD
(External input signal)
1.4 V
1.5 V
DVDD
DET
(IC inner signal)
I2C acceptance starts
RESET
(External input signal)
I2C acceptance stops
DVDD_DET:High and RESET:High
= I2C acceptance ON
LDO1ON
(External input signal)
1.2 V
0.45 V
at DCDC-start
OSC
(IC inner signal)
VLDO1
(IC output signal)
LDO1 starts in NM mode
Pin LDO1 starts
at LDO-start
I2C stops
I2C starts
Pin LDO1 stops
NM
NM
VLDO
2/3/4
(IC output signal)
DCDC1
(IC output signal)
I2C stops
I2C starts
NM
@ 150 μs
I2C stops
I2C starts
36
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
4. Timing Chart (Sequence – 3 (VLDO1 = connected DVDD))
VBAT
(External input signal)
REF
(IC output signal)
1.24 V
2.4 V
VREG
(IC output signal)
2.2 V
2.1 V
REGW
(IC inner signal)
DVDD:VLDO1
(External input signal)
1.5 V
1.4 V
DVDD
DET
(IC inner signal)
I2C acceptance starts
RESET
(External input signal)
I2C acceptance stops
DVDD_DET:High and RESET:High
= I2C acceptance ON
DVDD_DET:Low and RESET:Low
= I2C acceptance OFF
LDO1ON
(External input signal)
at LDO-start
OSC
(IC inner signal)
VLDO1
(IC output signal)
at DCDC-start
VLDO1 is connected directly with DVDD
Pin LDO1 starts
Pin LDO1 stops
1.4 V
1.5 V
VLDO
2/3/4
(IC output signal)
DCDC1
(IC output signal)
I2C starts
I2C starts
I2C stops
@ 150 μs
37
I2C stops
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
4. Timing Chart (Sequence – 4 (LDO2/3 are controlled by REGCNT))
VBAT
RESET
DVDD
(External input signal)
VREG
(IC output signal)
2.4V
2.2V
2.1V
REGW
(IC inner signal)
Initial Setting
I2 C
Control Resistor
ADDRESS:04h 00h 01h 02h 03h
DATA:61h 18h xxh xxh xxh
05h
02h
05h
00h
00h
00h
00h
10h
05h
01h
05h
00h
00h 05h
3Dh 04h
00h
19h
05h
09h
05h 00h
00h 18h
(External input signal)
LDO1ON
(External input signal)
REGCNT
(External input signal)
I2C starts
Pin LDO1 starts
NM
Pin REGCNT starts
VLDO2
(IC output signal)
NM
PS
I2C stops
PS
NM
NM
PS
NM
Pin REGCNT stops
I2C starts
NM
NM
I2C stops
Pin REGCNT starts
VLDO3
(IC output signal)
I2C stops
Pin LDO1 stops
VLDO1
(IC output signal)
Pin REGCNT stops
I2C starts
NM
NM
PS
I2C stops
I2C starts
VLDO4
(IC output signal)
NM
I2C starts
DCDC1
(IC output signal)
38
@ 150 μs
All LDOs can also be stopped
in PS Mode
NM
PS
NM
I2C stops
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
4. Timing Chart (Sequence – 4 (LDO2/3 are controlled by REGCNT)) (continued)
LDO2/3 are controlled
by REGCNT
I2 C
ADDRESS:04h 00h 01h 02h 03h
DATA:61h 18h xxh xxh xxh
05h
02h
Only LDO2 is controlled
by REGCNT
05h
00h
00h
00h
00h
10h
05h
01h
05h
00h
No REGCNT control
00h
19h
00h 05h
3Dh 04h
05h
09h
05h 00h
00h 18h
(External input signal)
REGCNT
(External input
signal)
VLDO2
(IC output signal)
Pin REGCNT stops
Pin REGCNT starts
I2C stops
Pin REGCNT starts
NM
VLDO3
(IC output signal)
NM
I2C stops
I2C stops
Pin REGCNT starts
I2C starts
NM
39
NM
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
Ground short protection
hysteresis
< Operation explanation >
(1) The Overcurrent protection operates
at about 1 A (Typ).
(2) The Ground protection sequence is implemented
when the output voltage decreases to about 70%
of the set voltage.
(3) The Ground short protection operates intermittently.
(2 ms : ON, 16 ms : OFF)
Output voltage [V]
5. DC-DC Protection Operation
Overcurrent protection (about 1 A)
Ground short protection
about 70% of Vout
Intermittent operation area
Pendency characteristic
about 150 mA
Output current [A]
Operation explanation chart
6. DAC voltage Accuracy
DCDC1 (VBAT = 3.7 V , Iout = –300 mA)
VDC1[3:0]
Output voltage Accuracy
[V]
[%]
D3
D2
D1
D0
0
0
0
0
0.80
±8.5
0
0
0
1
0.85
±6.5
0
0
1
0
0.90
±6.5
0
0
1
1
0.95
±6.0
0
1
0
0
1.00
±6.0
0
1
0
1
1.05
±5.0
0
1
1
0
1.10
±4.0
0
1
1
1
1.15
±3.5
1
0
0
0
1.20 (Default)
±2.5
1
0
0
1
1.30
±3.0
1
0
1
0
1.40
±4.0
1
0
1
1
1.50
±3.0
1
1
0
0
1.65
±3.0
1
1
0
1
1.80
±4.0
1
1
1
0
1.85
±3.0
1
1
1
1
2.40
±3.0
40
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
6. DAC Voltage Accuracy (continued)
LDO VBAT = 3.7 V (Normal-mode : Iout = – 150 mA, PS-mode : Iout = – 5 mA)
Accuracy [%]
VL1[3:0]
D3
D2
D1
D0
Output voltage
[V]
Normal-mode
PS-mode
LDO1
LDO2 to 4
LDO1
LDO2 to 4
0
0
0
0
1.00
±5.0
±5.0
±5.0
±5.0
0
0
0
1
1.10
±4.5
±4.5
±4.5
±4.5
0
0
1
0
1.20
±4.0
±4.0
±4.0
±4.0
0
0
1
1
1.30
±4.0
±4.0
±4.0
±4.0
0
1
0
0
1.40
±3.0
±3.0
±3.0
±3.0
0
1
0
1
1.50
±3.0
±3.0
±3.0
±3.0
0
1
1
0
1.60
±3.0
±3.0
±3.0
±3.0
0
1
1
1
1.70
±3.0
±3.0
±3.0
±3.0
1
0
0
0
1.80
±3.0
±3.0
±3.0
±3.0
1
0
0
1
1.85
±2.5
±2.5
±2.5
±2.5
1.90
1
0
±2.5
—
0
±2.5
—
1
2.60
—
±3.0
—
±3.0
1
0
1
1
2.70
±3.0
±3.0
±3.0
±3.0
1
1
0
0
2.80
±3.0
±3.0
±3.0
±3.0
1
1
0
1
2.85
±3.0
±3.0
±3.0
±3.0
1
1
1
0
3.00
±3.0
±3.0
±3.0
±3.0
1
1
1
1
3.30
±3.0
±3.0
±3.0
±3.0
41
Ver. AEB
AN30183A
OPERATION ( Continued )
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
7. Start Up Timing from LDO1ON , REGCNT and I2C
(1) Start up LDO1
Start up by LDO1ON
Start up by I2C
SDA
LDO1ON
<60μs
<100μs
LDO1
LDO1
VLDO*0.9
VLDO*0.9
(2) Start up LDO2/3/4 and DCDC1
Start up by REGCNT
Start up by I2C
SDA
REGCNT
<60μs
.
<100μs
LDO2/3/4
LDO2/3/4
VLDO*0.9
VLDO*0.9
Start up by REGCNT
Start up by I2C
REGCNT
SDA
<500μs
<500μs
DCDC1
DCDC1
VOUT*0.9
VOUT*0.9
42
Ver. AEB
AN30183A
APPLICATION INFORMATION
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
1.Application Circuit and Evaluation Board
CD1
DDVBAT1
VIN2
VB
DVDD
CV1
CV2
C1
SDA
L1
SCL
LX1
FB1
DDGND1
ASEL
REGCNT
LDO3
AN30183A
DCDCOUT1
CDCDCOUT1
LDO1
COUT3
COUT1
LDO4
LDO2
COUT4
COUT2
VREG
CVREG
REF
RESET LDO1ON AGND
CREF
Figure : Application Circuit
Figure : Top Layer with silk screen
( Top View ) with Evaluation Board
Figure : Bottom Layer with silk screen
( Bottom View ) with Evaluation Board
Notes) This application circuit and layout is an example. The operation of mass production set is not guaranteed. You should perform
enough evaluation and verification on the design of mass production set. You are fully responsible for the incorporation of the
above application circuit and information in the design of your equipment.
43
Ver. AEB
AN30183A
APPLICATION INFORMATION (Continued)
Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.
2.RECOMMENDED COMPONENT
Reference Designator
QTY
Value
Manufacturer
Part Number
C1
1
4.7µF
Murata
GRM21BB31C475KA87
CV1
1
4.7µF
Murata
GRM21BB31C475KA87
VC2
1
4.7µF
Murata
GRM21BB31C475KA87
CD1
1
0.1µF
Murata
GRM188B11C104KA01
L1
1
1.0 µH
FDK
MIPSZ2012D1R0
CDCDCOUT1
1
4.7µF
Murata
GRM21BB31A475KA74
COUT1
1
1.0µF
Murata
GRM185B31A105KE35
COUT2
1
1.0µF
Murata
GRM185B31A105KE35
COUT3
1
1.0µF
Murata
GRM185B31A105KE35
COUT4
1
1.0µF
Murata
GRM185B31A105KE35
CVREG
1
1.0µF
Murata
GRM185B31A105KE35
CREF
1
1.0µF
Murata
GRM185B31A105KE35
Figure : Recommended Component
44
Ver. AEB
AN30183A
PACKAGE INFORMATION ( Reference Data )
Outline Drawing
Package Code : XBGA020-W-1621AEL
Unit:mm
Body Materia l : Br/Sb Free Epoxy resin
Reroute Material : Cu
Bump
45
: SnAgCu
Ver. AEB
AN30183A
IMPORTANT NOTICE
1.The products and product specifications described in this book are subject to change without notice for
modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore,
ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your
requirements.
2.When using the LSI for new models, verify the safety including the long-term reliability for each product.
3.When the application system is designed by using this LSI, be sure to confirm notes in this book.
Be sure to read the notes to descriptions and the usage notes in the book.
4.The technical information described in this book is intended only to show the main characteristics and application
circuit examples of the products. No license is granted in and to any intellectual property right or other right owned
by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to
the infringement upon any such right owned by any other company which may arise as a result of the use of
technical information de-scribed in this book.
5.This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of
our company.
6.This LSI is intended to be used for general electronic equipment.
Consult our sales staff in advance for information on the following applications: Special applications in which
exceptional quality and reliability are required, or if the failure or malfunction of this LSI may directly jeopardize
life or harm the human body.
Any applications other than the standard applications intended.
(1) Space appliance (such as artificial satellite, and rocket)
(2) Traffic control equipment (such as for automobile, airplane, train, and ship)
(3) Medical equipment for life support
(4) Submarine transponder
(5) Control equipment for power plant
(6) Disaster prevention and security device
(7) Weapon
(8) Others : Applications of which reliability equivalent to (1) to (7) is required
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in
connection with your using the LSI described in this book for any special application, unless our company agrees
to your using the LSI in this book for any special application.
7.This LSI is neither designed nor intended for use in automotive applications or environments unless the specific
product is designated by our company as compliant with the ISO/TS 16949 requirements.
Our company shall not be held responsible for any damage incurred by you or any third party as a result of or in
connection with your using the LSI in automotive application, unless our company agrees to your using the LSI in
this book for such application.
8.If any of the products or technical information described in this book is to be exported or provided to non-residents,
the laws and regulations of the exporting country, especially, those with regard to security export control, must be
observed.
9. Please use this product in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive.
Our company shall not be held responsible for any damage incurred as a result of your using the LSI not
complying with the applicable laws and regulations.
46
Ver. AEB
AN30183A
USAGE NOTES
1. When designing your equipment, comply with the range of absolute maximum rating and the guaranteed
operating conditions (operating power supply voltage and operating environment etc.). Especially, please be
careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off
and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of
break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as
redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical
injury, fire, social damages, for example, by using the products.
2. Comply with the instructions for use in order to prevent breakdown and characteristics change due to external
factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's
process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf
life and the elapsed time since first opening the packages.
3. Pay attention to the direction of LSI. When mounting it in the wrong direction onto the PCB (printed-circuit-board),
it might smoke or ignite.
4. Pay attention in the PCB (printed-circuit-board) pattern layout in order to prevent damage due to short circuit
between pins. In addition, refer to the Pin Description for the pin configuration.
5. Perform a visual inspection on the PCB before applying power, otherwise damage might happen due to
problems such as a solder-bridge between the pins of the semiconductor device. Also, perform a full technical
verification on the assembly quality, because the same damage possibly can happen due to conductive
substances, such as solder ball, that adhere to the LSI during transportation.
6. Take notice in the use of this product that it might break or occasionally smoke when an abnormal state occurs
such as output pin-VCC short (Power supply fault), output pin-GND short (Ground fault), or output-to-output-pin
short (load short) .
And, safety measures such as an installation of fuses are recommended because the extent of the abovementioned damage and smoke emission will depend on the current capability of the power supply.
7. The protection circuit is for maintaining safety against abnormal operation. Therefore, the protection circuit
should not work during normal operation.
Especially for the thermal protection circuit, if the area of safe operation or the absolute maximum rating is
momentarily exceeded due to output pin to VCC short (Power supply fault), or output pin to GND short (Ground
fault), the LSI might be damaged before the thermal protection circuit could operate.
8. Unless specified in the product specifications, make sure that negative voltage or excessive voltage are not
applied to the pins because the device might be damaged, which could happen due to negative voltage or
excessive voltage generated during the ON and OFF timing when the inductive load of a motor coil or actuator
coils of optical pick-up is being driven.
9. The product which has specified ASO (Area of Safe Operation) should be operated in ASO
10. Verify the risks which might be caused by the malfunctions of external components.
11. Connect the metallic plates on the back side of the LSI with their respective potentials (AGND, PVIN, LX). The
thermal resistance and the electrical characteristics are guaranteed only when the metallic plates are connected
with their respective potentials.
47
Ver. AEB
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for general applications (such as office equipment, communications
equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,
life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of
the products may directly jeopardize life or harm the human body.
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with
your using the products described in this book for any special application, unless our company agrees to your using the products in
this book for any special application.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20100202