DATA SHEET Part No. AN12975A Package Code No. ULGA020-L-0404 Publication date: October 2008 SDE00029BEB 1 AN12975A Contents Overview ……..……………………………………………………………………………………………………. 3 Features ……..……………………………………………………………………………………………………. 3 Applications Package Type ………………………………………………………………………………………………………. 3 …………………………………...………………………………………………………………………. 3 …………….………………………………………………………………………………………………… 3 Application Circuit Example (Block Diagram) ……….…………………………………………………………. 4 Pin Descriptions …………………..………………………………………………………………………………. 5 Absolute Maximum Ratings ……………………..……………..…………………………......………………… 6 Operating Supply Voltage Range …………………………………………..……………………………………. 6 Electrical Characteristics ………………….………………….…………………………………………………. 7 Electrical Characteristics (Reference values for design) Technical Data Usage Notes ……………………………………………………. 9 …………………………………….………….…………………………………………………. 10 ……….……………………….………………….…………………………………………………. 21 SDE00029BEB 2 AN12975A AN12975A Stereo BTL amplifier IC with built-in AGC (I2C bus-control correspondence) Overview AN12975A is the stereo BTL amplifier which contained the AGC circuit for clip prevention of a speaker output. This IC performs a mode change by the I2C bus control system.(Standby function ON/OFF change etc.) Features y Selection by I2C bus control is possible in the on-level of AGC. (3-bit, 8-step) y Selection by I2C bus control is possible in an attack/recovery time of AGC. (attack: 2-bit , recovery: 3-bit) y The resistance and the capacitor of a detector circuit which were being used for the conventional AGC are unnecessary. y In order to realize high efficiency of output power, it adopts CMOS power amplifier circuit . Applications y Audio amplifier for mobile, such as a cellular phone Package y 20 pin plastic non lead package of four directions (LGA Type) Type y Silicon Monolithic Bi-CMOS IC SDE00029BEB 3 AN12975A Application Circuit Example (Block Diagram) VCC 3V 1 μF 1 μF 1 μF ROUT (Positive) 15 14 13 VREF 12 11 TEST1 VREFSP PREOUT-R 16 100 pF 0.1 μF ±0 dB + － 10 kΩ 17 GND 0.1 μF IN(L) +13 dB +4 dB 9 AGC +13 dB 10 kΩ FB-R IN(R) 10 kΩ ±0 dB + － FB-L 19 PREOUT-L SPEAKER 8Ω ROUT (Negative) VCC_SP DET 18 10 kΩ 100 pF GND_SPR 10 3V 8 1 μF AGC +4 dB 7 20 +13 dB I2C-BUS Control 6 2 3 SCL GND_SPL SPEAKER 8Ω +13 dB TEST2 1 LOUT (Negative) 4 5 SAD LOUT (Positive) 1 μF 10 kΩ 10 kΩ VCC_D 1.8 V Note) This circuit and these circuit constants show an example and do not guarantee the design as a mass-production set. SDE00029BEB 4 AN12975A Pin Descriptions Pin No. Pin name Type — Description 1 TEST2 2 SCL Input SCL 3 SAD Input / Output SDA 4 VCC_D Power Supply Power supply VCC_D for logic circuit 5 LOUT_POS Output SP amplifier L-ch. output (+) 6 GND_SPL Ground Ground for SP L-ch. amplifier system 7 LOUT_NEG Output SP amplifier L-ch. output (–) 8 VCC_SP 9 ROUT_NEG Output SP amplifier R-ch. output (–) 10 GND_SPR Ground Ground for SP R-ch. amplifier system 11 ROUT_POS Output SP amplifier R-ch. output (+) 12 VREF_SP 13 TEST1 14 VCC Power Supply 15 VREF Input 16 PREOUT_R 17 FB_R Input 18 GND Ground 19 FB_L Input 20 PREOUT_L Power Supply Input — Output Output Terminal for testing (please connect to Ground) Power supply VCC_SP for SP output Terminal of reference voltage for SP output circuit Terminal for testing (please connect to Ground) Power supply VCC Terminal of reference voltage First stage amplifier output R-ch. Negative feedback input stage amplifier R-ch. Ground Negative feedback input stage amplifier L-ch. First stage amplifier output L-ch. SDE00029BEB 5 AN12975A Absolute Maximum Ratings A No. 1 Parameter Supply voltage Symbol Rating VCC 3.6 VCC_D 3.6 VCC_SP 5.0 Unit Note V *1 2 Supply current ICC — A — 3 Power dissipation PD 222 mW *2 4 Operating ambient temperature Topr –20 to +70 °C *3 5 Storage temperature Tstg –55 to +150 °C *3 Note) *1: The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. *2: The power dissipation shown is the value at Ta = 70°C for the independent (unmounted) IC package without a heat sink. When using this IC, refer to the • PD – Ta diagram in the Technical Data and use under the condition not exceeding the allowable value. *3: Except for the power dissipation, operating ambient temperature, and storage temperature, all ratings are for Ta = 25°C. Operating Supply Voltage Range Parameter Supply voltage range Symbol Range VCC 2.7 to 3.3 VCC_D 1.7 to 2.6 VCC_SP 2.7 to 4.5 Unit Note V Note) The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. SDE00029BEB 6 AN12975A Electrical Characteristics at VCC = 3.0 V , VCC_D = 1.8 V , VCC_SP = 3.0 V Note) Ta = 25°C±2°C unless otherwise specified. B No. Parameter Symbol Conditions Limits Min Typ Max Unit No te Circuit Current 1 Circuit current 1A at non-signal (VCC) IVCC1A VCC = 3.0 V, Non-signal STB = OFF, SP = ON, AGC = ON 1.5 3.9 6.0 mA 2 Circuit current 2A at non-signal (VCC_SP) IVCC2A VCC_SP = 3.0 V, Non-signal STB = OFF, SP = ON, AGC = ON 1.0 13 24 mA 3 Circuit current 3A at non-signal (VCC_D) IVCC3A VCC_D = 1.8 V, Non-signal STB = OFF, SP = ON, AGC = ON ⎯ 0.1 10 μA 4 Circuit current 1B at non-signal (VCC) IVCC1B VCC = 3.0 V, Non-signal STB = ON, SP = OFF, AGC = ON ⎯ 0.1 1.0 μA 5 Circuit current 2B at non-signal (VCC_SP) IVCC2B VCC_SP = 3.0V, Non-signal STB = ON, SP = OFF, AGC = ON ⎯ 0.1 1.0 μA 6 Circuit current 3A at non-signal (VCC_D) IVCC3B VCC_D = 1.8 V, Non-signal STB = ON, SP = OFF, AGC = ON ⎯ 0.1 1.0 μA 7 Circuit current 1C at non-signal (VCC) IVCC1C VCC = 3.0 V, Non-signal STB = OFF, SP = OFF, AGC = ON 1.5 3.7 6.0 mA 8 Circuit current 1C at non-signal (VCC_SP) IVCC2C VCC_SP = 3.0 V, Non-signal, STB = OFF, SP = OFF, AGC = ON ⎯ 0.3 1.0 mA 9 Circuit current 1C at non-signal (VCC_D) IVCC3C VCC_D = 1.8 V, Non-signal STB = OFF, SP = OFF, AGC = ON ⎯ 0.1 10 μA VSPOL VSPOR Vin = –31.0 dBV , f = 1 kHz RL = 8 Ω –9.5 –8.0 –6.5 dBV 12 SP reference output distortion THSPOL THSPOR Vin = –31.0 dBV , f = 1 kHz RL = 8 Ω, to THD 5th ⎯ 0.07 0.5 % 13 SP reference output noise voltage VNSPOL Non-Signal VNSPOR using A curve filter ⎯ –78 –71 dBV 14 SP maximum rating output VMSPOL THD = 10% , f = 1 kHz VMSPOR RL = 8 Ω, AGC = OFF 300 500 ⎯ mW 15 output level at power save VSSPOL VSSPOR ⎯ –114 –90 dBV Input/output characteristics 11 SP reference output level Vin = –31.0 dBV , f = 1 kHz RL = 8 Ω, using A curve filter 16 SP AGC output level 1 Vin = –17.0 dBV , f = 1 kHz VSPOA1L RL = 8 Ω VSPOA1R AGC－SELECT = [100] 3.0 4.0 5.0 dBV 17 SP AGC output level 2 Vin = –12.0 dBV , f = 1 kHz VSPOA2L RL = 8 Ω VSPOA2R AGC – SELECT = [100] 3.0 4.0 5.0 dBV SDE00029BEB 7 AN12975A Electrical Characteristics at VCC = 3.0 V , VCC_D = 1.8 V , VCC_SP = 3.0 V (continued) Note) Ta = 25°C±2°C unless otherwise specified. B No. Parameter Symbol Conditions Limits Min Typ Max Unit No te I2C interface 43 SCL, SDA signal input low level VIL – 0.5 ⎯ 0.3 × VCC_D V 44 SCL, SDA signal input low level VIH 0.7 × VCC_D ⎯ VCC_D + 0.5 V 0 ⎯ 0.2 × VCC_D V –10 ⎯ 10 μA 0 ⎯ 400 kHz 45 SDA output signal low level 46 SCL, SDA signal input current 47 SCL maximum frequency of signal input VOL Ii Open corrector, Sync current: 3 mA Input voltage: 0.1 V to 1.7 V fSCL SDE00029BEB 8 AN12975A Electrical Characteristics (Reference values for design) at VCC = 3.0 V , VCC_D = 1.8 V, VCC_SP = 3.0 V Note) Ta = 25°C±2°C unless otherwise specified. The characteristics listed below are reference values derived from the design of the IC and are not guaranteed by inspection. If a problem does occur related to these characteristics, we will respond in good faith to user concerns. B No. Parameter Symbol Limits Conditions Unit No te ⎯ μs *1 Min Typ Max tBUF 1.3 ⎯ I2C interface 66 Bass free time between a condition of stop and a condition of start 67 Setup time of a condition of start tSU;STA 0.6 ⎯ ⎯ μs *1 68 Hold time of a condition for satart tHD;STA 0.6 ⎯ ⎯ μs *1 69 "L" time of SCL clock tLow 1.3 ⎯ ⎯ μs *1 70 "H" time of SCL clock tHigh 0.6 ⎯ ⎯ μs *1 71 rising time of SDA , SCL signal tR ⎯ ⎯ 0.3 μs *1 72 fall time of SDA,SCL signal tF ⎯ ⎯ 0.3 μs *1 73 Data setup time tSU;DAT 0.1 ⎯ ⎯ μs *1 74 Data hold time tHD;DAT 0 ⎯ 0.9 μs *1 75 Rising up time of a condition of stop tSU;STO 0.6 ⎯ ⎯ μs *1 Note) *1: All values are VIHmin (*2) and VILmax (*3) level standard. *2: VIHmin is the minimum limit of the signal input high level. *3: VILmax is the maximum limit of the signal input low level. Repeated START CONDITION START CONDITION STOP CONDITION START CONDITION VIHmin (*2) SAD VILmax (*3) tBUF tR tF tLow tR tSU;DAT tF tHD;STA SCL tHD;STA tHD;DAT tHigh tSU;STA SDE00029BEB tSU;STO 9 AN12975A Technical Data y I2C-bus Mode 1. Write Mode SAD SCL SLAVE ADDRESS START CONDITION ACK 1 0 1 1 0 1 1 0 B 6 SUB ADDRESS 0 0 0 0 DATA ACK 0 0 0 1 0 1 Example of transmission messages ACK 1 0 0 0 0 0 0 0 8 0 STOP CONDITION Two transmission messages (i.e., the SCL and SDA) are sent in synchronous serial transmission. The SCL is a clock with fixed frequency. The SDA indicates address data for the control of the reception side, and is sent in parallel in synchronization with the SCL. The data is transmitted in 8-bit, 3 octets (bytes) in principle, where every octet has an acknowledge bit. The following description provides information on the structure of the frame. <Start Conditions> When the level of the SDA changes to low from high while the level of the SCL is high, the data reception of the receiver will be enabled. <Stop Conditions> When the level of the SDA changes to high from low while the level of the SCL is high, the data reception of the receiver will be aborted. <Slave Address> The slave address is a specified one unique to each device. When the address of another device is sent, the reception will be aborted. <Sub Address> The sub address is a specified one unique to each function. <Data> Data is information under control. <Acknowledge Bit> The acknowledge bit is used to enable the master to acknowledge the reception of data for each octet. The master acknowledges the data reception of the receiver by transmitting a high-level signal to the receiver and receiving a low-level signal returned from the receiver as shown by the dotted lines in Fig. The communication will be aborted if the low signal is not returned. The SDA will not change when the level of the SCL is high except start or stop conditions are enabled. SDE00029BEB 10 AN12975A Technical Data (continued) y I2C-bus Mode (continued) 1. Write Mode (continued) (a) I2C-bus PROTOCOL x Slave address: 10110110 (B6Hex) x Format (normal) S Slave address W A Start condition Sub address A Data byte Acknowledge bit Write Mode: 0 A P Stop condition (b) Auto increment x Sub-address 0*Hex: Auto increment mode (When the data is sent in sequence, the sub address will change one by one and the data will be input.) x Auto increment mode S Slave address W A Sub address A Data 1 A Data 2 A Data n A P (c) Initial condition The initial state of the device is not guaranteed. Therefore, the input of 00Hex resister-D0 (Note.1) will be absolutely 0, when the power is turned ON. (d) Sub-address Byte and Data Byte Format Sub-address *0Hex *1Hex *2Hex Data byte MSB D3 D7 D6 D5 D4 ＊ ＊ 0 (Note.2) 0 (Note.2) AGC-ON AGC-ON data bit3 data bit2 0 (Note.2) AGC-ON data bit1 0 (Note.2) <00Hex Register> D0, D4, D5, D6, D7: Always set to 0 D1: Standby ON/OFF switch D2: SP Save ON/OFF switch D3: AGC ON/OFF switch <01Hex Register> D0, D1 : AGC-attack-time selection D2, D3, D4: AGC-recovery-time selection D5, D6, D7: AGC-on-level selection <02Hex Register> D0 to D7: Always set to 0 (test&adjust mode) 0 (Note.2) LSB AGC 0 → OFF 1 → ON D2 SP Save 0 → ON 1 → OFF D1 Standby 0 → ON 1 → OFF D0 0 (Note.1) AGC-REC AGC-REC AGC-REC AGC-ATT AGC-ATT data bit3 data bit2 data bit1 data bit2 data bit1 ＊ 0 (Note.2) SDE00029BEB ＊ 0 (Note.2) 0 (Note.2) 0 (Note.2) Please use these bit only Data = "0", because they are used by our company’s final test and fine-tuning AGC-on level. 11 AN12975A Technical Data (continued) y I2C-bus Mode (continued) 1. Write Mode (continued) (e) AGC-attack-time selection Write 01Hex Register (f) AGC-recovery-time selection Write 01Hex Register Attack time Recovery time D4 D3 D2 0.5 ms 0 0 0 1.0 s 1 1 ms 0 0 1 1.5 s 1 0 2 ms 0 1 0 2.0 s 1 1 4 ms 0 1 1 3.0 s 1 0 0 4.0 s 1 0 1 6.0 s 1 1 0 8.0 s 1 1 1 12.0 s D1 D0 0 0 0 (g) AGC-on-level selection (at VCC = 3.0 V, VCC_SP = 3.0V) Write 01Hex Register AGC On Level Output Po (Ω) VCC_SP (Recommend) D7 D6 D5 0 0 0 0 dBv 125 mΩ - 0 0 1 1 dBv 157 mΩ - 0 1 0 2 dBv 198 mΩ - 0 1 1 3 dBv 249 mΩ - 1 0 0 4 dBv 314 mΩ 3.0 V ≤ 1 0 1 5 dBv 395 mΩ 3.3 V ≤ 1 1 0 6 dBv 498 mΩ 3.7 V ≤ 1 1 1 7 dBv 626 mΩ 4.1 V ≤ * Note) *: We recommend more than VCC = 2.9 V for 7 dBV output level. SDE00029BEB 12 AN12975A Technical Data (continued) y I2C-bus Mode (continued) 2. Read Mode (a)I2C-bus PROTOCOL x Slave address 10110111(B7Hex) x Format S Slave address R A Data 0 A Data 1 A Data 2 A P Read Mode: 1 Note) At the slave address input, it is sequentially output from data 0. There is no necessity for inputting the sub-address. (b) Sub-address Byte and Data Byte Format MSB D7 Data byte D6 D4 D5 LSB D3 D2 D1 D0 Data 0 Sub address Sub address *0Hex *0Hex Latch data Latch data [D6] [D7] Sub address *0Hex Latch data [D5] Sub address Sub address *0Hex *0Hex Latch data Latch data [D3] [D4] Sub address *0Hex Latch data [D2] Sub address *0Hex Latch data [D1] Sub address *0Hex Latch data [D0] Data 1 Sub address Sub address *1Hex *1Hex Latch data Latch data [D6] [D7] Sub address *1Hex Latch data [D5] Sub address Sub address *1Hex *1Hex Latch data Latch data [D3] [D4] Sub address *1Hex Latch data [D2] Sub address *1Hex Latch data [D1] Sub address *1Hex Latch data [D0] Data 2 Sub address Sub address *2Hex *2Hex Latch data Latch data [D6] [D7] Sub address *2Hex Latch data [D5] Sub address Sub address *2Hex *2Hex Latch data Latch data [D3] [D4] Sub address *2Hex Latch data [D2] Sub address *2Hex Latch data [D1] Sub address *2Hex Latch data [D0] Purchase of Panasonic I2C components conveys a license under the Philips I2C patent right to use these components in an I2C systems, provided that the system conforms to the I2C standard specification as defined by Philips. y Operating temperature guarantee of I2C-bus Control The performance in the ambient temperature of operation is guaranteed theoretically in the design at normal temperature (25°C) by inspecting it at a speed of the clock that is about 50% earlier regarding the operating temperature guarantee of I2C-bus Control. But the following characteristics are logical values derived from the design of the IC and are not guaranteed by inspection. If a problem does occur related to these characteristics ,Panasonic will respond in good faith to customer concerns. SDE00029BEB 13 AN12975A Technical Data (continued) y I/O block circuit diagrams and pin function descriptions Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin No. Waveform and voltage Internal circuit Description VCC TEST mode output pin Test2 1 Hi-Z 1k It is Hi-Z at normal operation. 1k Please connect to GND. VCC_D SCL I2C-bus SCL pin 2 Hi-Z VCC_D SAD 3 I2C-bus SDA pin Hi-Z GND VCC_D 4 － Power supply pin for I2C-bus 1.8 V(typ.) SDE00029BEB 14 AN12975A Technical Data (continued) y I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin No. Waveform and voltage Internal circuit Description VCC_SP LOUT_POS L-ch. positive speaker output pin 5 DC 1.45 V 400k GND_SPL 6 GND_SPL Ground pin for L-ch. speaker output － VCC_SP LOUT_NEG 7 L-ch. negative speaker output pin DC 1.45 V 400k GND_SPL VCC_SP 8 － Power supply pin for speaker output 3.0 V(typ.) SDE00029BEB 15 AN12975A Technical Data (continued) y I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin No. Waveform and voltage Internal circuit Description VCC_SP ROUT_NEG 9 R-ch. positive speaker output pin DC 1.45 V 400k GND_SPR 10 GND_SPR GND pin for R-ch. speaker output － VCC_SP ROUT_POS 11 R-ch. negative speaker output pin DC 1.45 V 400k GND_SPR VCC_SP VREF_SP 12 DC 1.45 V 10k 1k 150k Reference voltage pin for output stage 150k SDE00029BEB 16 AN12975A Technical Data (continued) y I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin No. Waveform and voltage Internal circuit Description Test1 Test mode pin Hi-Z Please connect to GND. 13 VCC 14 Power supply pin － 3.0 V(typ.) VCC VREF 10k 15 1k DC 1.45 V 150k Reference voltage pin 150k VCC First stage amplifier L-ch. output pin PREOUT_R 16 DC 1.45 V 10k 1k SDE00029BEB 17 AN12975A Technical Data (continued) y I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin No. Waveform and voltage FB_R Internal circuit Description 10k Negative feedback pin for input stage amplifier L-ch. 17 DC 1.45 V 18 GND FB_L Ground pin － 10k Negative feedback pin for input stage amplifier L-ch. 19 DC 1.45 V VCC PREOUT_L First stage amplifier L-ch. output pin 20 DC 1.45 V 10k 1k SDE00029BEB 18 AN12975A Technical Data (continued) y Power supply and logic sequence Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. The timing control of power-ON/OFF and each logic according to the procedure below should be recommended for the best pop performance caused in switching. 1. The sequence of the power supply and each logic The basic procedure at the power-on Please first bring up the power supply, and then the standby off. VCC,VCC_SP, VCC_D Power supply Off On On Off Off Standby 1. The power OFF condition Both the standby and the SP_Save are in the ON condition. 2. Power ON 3. Standby Off 4. SP_Save Off Off On On Off Off SP_Save The basic procedure at the power-off On On 20 ms or more * After at least 20 ms has passed after the standby off, please off SP_Save. 0 ms or more 1. The power ON condition Both the standby and the SP_Save are in the OFF condition. 2. SP_Save On ( = Standby On) 3. Standby On 4. Power Off Please control Standby On to simultaneous with SP_Save On, or the back. Note) *: This IC contains the pre-charge circuit. It is time until each bias is stabilized from Standby Off. It depends for this time on the capacity value linked to a reference voltage terminal (VREF and VREFSP), and the capacity value and resistance linked to an input terminal (IN_R and IN_L). It is a recommendation value in a constant given in the example of Application Circuit Example (Block Diagram). 2．The sequence of VCC and VCC_SP and VCC_D This IC have not a standup and falling order in VCC and VCC_SP. A standup and falling time of VCC and VCC_SP recommend 1 or more ms. VCC VCC_SP VCC_D On On Off Off 1 ms or more 1 ms or more SDE00029BEB 19 AN12975A Technical Data (continued) y PD ⎯ Ta diagram SDE00029BEB 20 AN12975A Usage Notes 1. Please take notice in the use of this product that it might break or occasionally smoke when an abnormal state occurs such as SP output pin (Pin5, Pin7, Pin9, Pin11) – power supply pin short, SP output pin (Pin5, Pin7, Pin9, Pin11) – GND short, or SP output (Pin5, Pin7, Pin9, Pin11)-to-SP output-pin short (load short). 2. Please absolutely do not mount the IC in the reverse direction on to the printed-circuit-board. It damaged when the electricity is turned on. SDE00029BEB 21 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805