5939

Package Information
Vishay Siliconix
-B-
PowerPAKr MLP65-18/20 (POWER IC ONLY)
D
D/2
NXb
Index Area
D/2 E/2
-A-
bbb
M
A
B
C
NXb
2x
E/2
E2/2
E2
2.00
aaa
C
E
Index Area
D/2 E/2
aaa
NXL
2x
C
Detail D
D2/2
D2
TOP VIEW
BOTTOM VIEW
A
//
ccc
C
0.08
C
A3
SEATING
NX
PLANE
-C-
SIDE VIEW
A1
# IDENTIFIER TYPE A
Chamber
e/2
Terminal Tip
e
Terminal Tip
e
5
EVEN TERMINAL SIDE
5
ODD TERMINAL SIDE
DETAIL B
Document Number: 73182
15-Oct-04
www.vishay.com
1
Package Information
Vishay Siliconix
PowerPAK MLP65-18/20 (POWER IC ONLY)
N = 18/20 PITCH: 0.5 mm, BODY SIZE: 6.00 x 5.00
MILLIMETERS*
Dim
Min
Nom
A
0.80
0.90
A1
0.00
0.02
A2
0.00
0.65
A3
0.20 REF
aaa
−
0.15
b
0.18
0.25
bbb
−
0.10
C’
−
0.225
ccc
−
0.10
D
6.00 BSC
D2
4.00
4.15
E
5.00 BSC
E2
3.00
3.15
e
−
0.50
L
0.45
0.55
N
18, 20
ND(18)
9
NE(18)
0
ND(20)
10
NE(20)
0
* Use millimeters as the primary measurement.
INCHES
Max
Min
Nom
Max
Notes
1.00
0.05
1.00
0.031
0.000
0.000
0.039
0.002
0.004
1, 2
1, 2
1, 2
−
0.30
−
−
−
−
0.007
−
−
−
4.25
0.157
3.25
−
0.65
0.118
−
0.018
0.035
0.001
0.003
0.008 REF
0.006
0.010
0.004
0.009
0.004
0.236 BSC
1.63
0.197 BSC
0.124
0.020
0.022
18, 20
9
0
10
0
−
0.012
−
−
−
0.167
0.128
−
0.026
8
4, 10
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
ECN: S-41946—Rev. A, 18-Oct-04
DWG: 5939
NOTES:
1.
Dimensioning and tolerancing conform to ASME Y14.5M-1994.
2.
All dimensions are in millimeters. All angels are in degrees.
3.
N is the total number of terminals.
4.
The terminal #1 identifier and terminal numbering convention shall conform to JEDEC publication 95 SSP-022. Details of terminal #1 identifier are optional,
but must be located within the zone indicated. A dot can be marked on the top side by pin 1 to indicate orientation.
5.
ND and NE refer to the number of terminals on the D and E side respectively.
6.
Depopulation is possible in a symmetrical fashion.
7.
NJR refers to NON JEDEC REGISTERED.
8.
Dimension “b” applies to metalized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has optional radius on
the other end of the terminal, the dimension “b” should not be measured in that radius area.
9.
Coplanarity applies to the exposed heat slug as well as the terminal.
10.
The 45_ chamfer dimension C’ is located by pin 1 on the bottom side of the package.
www.vishay.com
2
Document Number: 73182
15-Oct-04