TCN75 DATA SHEET (02/05/2013) DOWNLOAD

TCN75
2-Wire Serial Temperature Sensor and Thermal Monitor
Features:
• Solid-State Temperature Sensing:
0.5°C Accuracy (Typ.)
• Operates from -55°C to +125°C
• Operating Supply Range: 2.7V to 5.5V
• Programmable Trip Point and Hysteresis with
Power-up Defaults
• Standard 2-Wire Serial Interface
• Thermal Event Alarm Output Functions as
Interrupt or Comparator/Thermostat Output
• Up to 8 TCN75s may Share the Same Bus
• Shutdown Mode for Low Standby Power
Consumption
• 5V Tolerant I/O at VDD = 3V
• Low Power:
- 250 A (Typ.) Operating
- 1 A (Typ.) Shutdown Mode
• 8-Pin SOIC and MSOP Packaging
Package Type
SOIC
SDA
1
8
VDD
SCL
2
7
A0
INT/CMPTR
3
6
A1
GND
4
5
A2
TCN75MOA
MSOP
SDA 1
8
VDD
7
A0
INT/CMPTR 3
6
A1
GND 4
5
A2
SCL 2
TCN75MUA
General Description:
Applications:
•
•
•
•
Thermal Protection for High-Performance CPUs
Solid-State Thermometer
Fire/Heat Alarms
Thermal Management in Electronic Systems:
- Computers
- Telecom Racks
- Power Supplies/UPS/Amplifiers
• Copiers/Office Electronics
• Consumer Electronics
• Process Control
The TCN75 is a serially programmable temperature
sensor that notifies the host controller when ambient
temperature exceeds a user programmed set point.
Hysteresis is also programmable. The INT/CMPTR
output is programmable as either a simple comparator
for thermostat operation or as a temperature event
interrupt. Communication with the TCN75 is
accomplished via a two-wire bus that is compatible with
industry standard protocols. This permits reading the
current temperature, programming the set point and
hysteresis, and configuring the device.
The TCN75 powers up in Comparator mode with a
default set point of 80°C with 5°C hysteresis. Defaults
allow independent operation as a stand-alone
thermostat. A shutdown command may be sent via the
2-wire bus to activate the low-power Standby mode.
Address selection inputs allow up to eight TCN75s to
share the same 2-wire bus for multizone monitoring.
All registers can be read by the host and the INT/
CMPTR output’s polarity is user programmable. Both
polled and interrupt driven systems are easily
accommodated. Small physical size, low installed cost,
and ease-of-use make the TCN75 an ideal choice for
implementing sophisticated system management
schemes.
 2001-2012 Microchip Technology Inc.
DS21490D-page 1
TCN75
Device Selection Table
Part Number
Supply Voltage
Package
Junction Temperature Range
TCN75-3.3MOA
3.3
8-Pin SOIC
-55°C to +125°C
TCN75-5.0MOA
5.0
8-Pin SOIC
-55°C to +125°C
TCN75-3.3MUA
3.3
8-Pin MSOP
-55°C to +125°C
TCN75-5.0MUA
5.0
8-PIn MSOP
-55°C to +125°C
Functional Block Diagram
INT/CMPTR
TCN75
9-Bit
DS
A/D
Converter
VDD
Temp
Sensor
Control
Logic
Register Set
Configuration
Temperature
TSET
THYST
SDA
SCL
A0
A1
A2
DS21490D-page 2
Two Wire
Serial Port
Interface
 2001-2012 Microchip Technology Inc.
TCN75
1.0
ELECTRICAL
CHARACTERISTICS
*Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only and functional
operation of the device at these or any other conditions
above those indicated in the operation sections of the
specifications is not implied. Exposure to Absolute
Maximum Rating conditions for extended periods may
affect device reliability.
Absolute Maximum Ratings*
Supply Voltage (VDD) ............................................ 6.0V
ESD Susceptibility (Note 3) ............................... 1000V
Voltage on Pins:
A0, A1, A2 .......... (GND – 0.3V) to (VDD + 0.3V)
Voltage on Pins:
SDA, SCL, INT/CMPTR .. (GND – 0.3V) to 5.5V
Thermal Resistance (Junction to Ambient)
8-Pin SOIC.......................................... 170°C/W
8-Pin MSOP ....................................... 250°C//W
Operating Temperature Range (TJ): -55°C to +125°C
Storage Temperature Range (TSTG): -65°C to +150°C
TCN75 ELECTRICAL SPECIFICATIONS
Electrical Characteristics: VDD = 2.7V – 5.5V, -55°C  (TA = TJ)  125°C, unless otherwise noted.
Symbol
Parameter
Min
Typ
Max
Units
Test Conditions
Power Supply
VDD
Power Supply Voltage
2.7
—
5.5
—
IDD
Operating Current
—
—
0.250
—
—
1.0
mA
Serial Port Inactive (TA = TJ = 25°C)
Serial Port Active
IDD1
Standby Supply Current
—
1
—
A
Shutdown Mode, Serial Port
Inactive (TA = TJ = 25°C)
—
1
4
mA
Note 1
INT/CMPTR Output
IOL
Sink Current: INT/CMPTR,
SDA Outputs
tTRIP
INT/CMPTR Response Time
1
—
6
VOL
Output Low Voltage
—
—
0.8
tCONV User Programmable
V
IOL = 4.0 mA
—
±3
—
C
-55°C  TA  +125°C
Temp-to-Bits Converter
T
Temperature Accuracy (Note 2)
VDD = 3.3V: TCN75-3.3 MOA,
TCN75-3.3 MUA
VDD = 5.0V: TCN75-5.0 MOA,
TCN75-5.0 MUA
—
±0.5
±3
C
—
55
—
msec
25°C  TA  100°C
tCONV
Conversion Time
TSET(PU)
TEMP Default Value
—
80
—
C
Power-up
THYST(PU)
THYST Default Value
—
75
—
C
Power-up
2-Wire Serial Bus Interface
VIH
Logic Input High
VDD x 0.7
—
—
V
VIL
Logic Input Low
—
—
VDD x 0.3
V
VOL
Logic Output Low
—
—
0.4
V
CIN
Input Capacitance SDA, SCL
—
15
—
pF
ILEAK
I/O Leakage
—
±100
—
pA
IOL(SDA)
SDA Output Low Current
—
—
6
mA
 2001-2012 Microchip Technology Inc.
IOL = 3 mA
(TA = TJ = 25°C)
DS21490D-page 3
TCN75
TCN75 ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: 2.7V  VDD  5.5V; -55°C  (TA = TJ)  125°C, CL = 80 pF, unless otherwise noted.
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
Serial Port Timing
fSC
Serial Port Frequency
0
100
400
kHz
tLOW
Low Clock Period
1250
—
—
nsec
tHIGH
High Clock Period
1250
—
—
nsec
tR
SCL and SDA Rise Time
—
—
250
nsec
tF
SCL and SDA Fall Time
—
—
250
nsec
tSU(START)
Start Condition Setup Time (for
repeated Start Condition)
1250
—
—
nsec
tSC
SCL Clock Period
2.5
—
—
sec
tH(START)
Start Condition Hold Time
100
—
—
nsec
tDSU
Data in Setup Time to SCL High
100
—
—
nsec
tDH
Data in Hold Time after SCL Low
0
—
—
nsec
tSU(STOP)
Stop Condition Setup Time
100
—
—
nsec
tIDLE
Bus Free Time Prior to New Transition
1250
—
—
nsec
Note
1:
Output current should be minimized for best temperature accuracy. Power dissipation within the TCN75 will cause self-heating and
temperature drift. At maximum rated output current and saturation voltage, 4 mA and 0.8V, respectively, the error amounts to 0.544°C for
the SOIC.
2:
All part types of the TCN75 will operate properly over the wider power supply range of 2.7V to 5.5V. Each part type is tested and specified
for rated accuracy at its nominal supply voltage. As VDD varies from the nominal value, accuracy will degrade 1°C/V of VDD change.
3:
Human body model, 100 pF discharged through a 1.5k resistor.
TIMING DIAGRAM
tSC
SCL
tH (Start)
tSU (Stop)
SDA
Data In
tDSU
SDA
Data Out
tDH
DS21490D-page 4
 2001-2012 Microchip Technology Inc.
TCN75
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
Pin Number
(8-Pin SOIC)
8-Pin MSOP)
Symbol
1
SDA
Bidirectional Serial Data.
2
SCL
Serial Data Clock Input.
3
INT/CMPTR
4
GND
5
A2
Address Select Pin (MSB).
6
A1
Address Select Pin.
7
A0
Address Select Pin (LSB).
8
VDD
 2001-2012 Microchip Technology Inc.
Description
Interrupt or Comparator Output.
System Ground.
Power Supply Input.
DS21490D-page 5
TCN75
3.0
DETAILED DESCRIPTION
A typical TCN75 hardware connection is shown in
Figure 3-1.
+VDD (3V to 5.5V)
CBypass
0.1 µF Recommended
Unless Device is Mounted
Close to CPU
8
A0
Address
(Set as Desired) A1
A2
7
6
5
I2C™ Interface SDA
SCL
1
2
3
TCN75
To Controller
INT/CMPTR
4
FIGURE 3-1:
3.1
Typical Application
Serial Data (SDA)
Bidirectional. Serial data is transferred in both
directions using this pin.
3.4
Address (A2, A1, A0)
Input. Clocks data into and out of the TCN75.
Inputs. Sets the three Least Significant bits of the
TCN75 8-bit address. A match between the TCN75’s
address and the address specified in the serial bit
stream must be made to initiate communication with
the TCN75. Many protocol-compatible devices with
other addresses may share the same 2-wire bus.
3.3
3.5
3.2
Serial Clock (SCL)
INT/CMPTR
Open Collector, Programmable Polarity. In Comparator
mode, unconditionally driven active any time
temperature exceeds the value programmed into the
TSET register. INT/CMPTR will become inactive when
temperature subsequently falls below the THYST setting. (See Section 5.0 “Register Set and Programmer’s ModeL”, Register Set and Programmer’s
Model). In Interrupt mode, INT/CMPTR is also made
active by TEMP exceeding TSET; it is unconditionally
reset to its inactive state by reading any register via the
2-wire bus. If and when temperature falls below THYST,
INT/CMPTR is again driven active. Reading any register will clear the THYST interrupt. In Interrupt mode, the
INT/CMPTR output is unconditionally reset upon entering Shutdown mode. If programmed as an active-low
output, it can be wire-ORed with any number of other
open collector devices. Most systems will require a
pull-up resistor for this configuration.
Slave Address
The four Most Significant bits of the Address Byte (A6,
A5, A4, A3) are fixed to 1001[B]. The states of A2, A1
and A0 in the serial bit stream must match the states of
the A2, A1 and A0 address inputs for the TCN75 to
respond with an Acknowledge (indicating the TCN75 is
on the bus and ready to accept data). The Slave
Address is represented in Table 3-1.
TABLE 3-1:
1
MSB
0
TCN75 SLAVE ADDRESS
0
1
A2
A1
A0
LSBS
Note that current sourced from the pull-up resistor
causes power dissipation and may cause internal heating of the TCN75. To avoid affecting the accuracy of
ambient temperature readings, the pull-up resistor
should be made as large as possible. INT/CMPTR’s
output polarity may be programmed by writing to the
INT/CMPTR POLARITY bit in the CONFIG register.
The default is active low.
DS21490D-page 6
 2001-2012 Microchip Technology Inc.
TCN75
3.6
Comparator/Interrupt Modes
INT/CMPTR behaves differently depending on whether
the TCN75 is in Comparator mode or Interrupt mode.
Comparator mode is designed for simple thermostatic
operation. INT/CMPTR will go active anytime TEMP
exceeds TSET. When in Comparator mode, INT/
CMPTR will remain active until TEMP falls below
THYST, whereupon it will reset to its inactive state. The
state of INT/CMPTR is maintained in Shutdown mode
when the TCN75 is in Comparator mode. In Interrupt
mode, INT/CMPTR will remain active indefinitely, even
if TEMP falls below THYST, until any register is read via
the 2-wire bus. Interrupt mode is better suited to interrupt driven microprocessor-based systems. The INT/
CMPTR output may be wire-OR’ed with other interrupt
sources in such systems. Note that a pull-up resistor is
necessary on this pin since it is an open-drain output.
Entering Shutdown mode will unconditionally reset INT/
CMPTR when in Interrupt mode.
 2001-2012 Microchip Technology Inc.
DS21490D-page 7
TCN75
4.0
SHUTDOWN MODE
When the appropriate bit is set in the configuration register (CONFIG) the TCN75 enters its low-power Shutdown mode (IDD = 1 A, typical) and the temperatureto-digital conversion process is halted. The TCN75’s
bus interface remains active and TEMP, TSET, and
THYST may be read from and written to. Transitions on
SDA or SCL due to external bus activity may increase
the standby power consumption. If the TCN75 is in
Interrupt mode, the state of INT/CMPTR will be reset
upon entering Shutdown mode.
4.1
Term
Serial Port Operation
The Serial Clock input (SCL) and bidirectional data port
(SDA) form a 2-wire bidirectional serial port for programming and interrogating the TCN75. The following
table indicates TCN75 conventions that are used in this
bus scheme.
SERIAL BUS CONVENTIONS
Explanation
Transmitter
Receiver
The device sending data to the bus.
The device receiving data from the bus.
Master
The device which controls the bus: initiating
transfers (Start), generating the clock, and
terminating transfers (Stop).
Slave
The device addressed by the master.
Start
A unique condition signaling the beginning of
a transfer indicated by SDA falling (High –
Low) while SCL is high.
Stop
A unique condition signaling the end of a
transfer indicated by SDA rising (Low – High)
while SCL is high.
ACK
A Receiver acknowledges the receipt of each
byte with this unique condition. The Receiver
drives SDA low during SCL high of the ACK
clock-pulse. The Master provides the clock
pulse for the ACK cycle.
Fault Queue
To lessen the probability of spurious activation of INT/
CMPTR the TCN75 may be programmed to filter out
transient events. This is done by programming the
desired value into the Fault Queue. Logic inside the
TCN75 will prevent the device from triggering INT/
CMPTR unless the programmed number of sequential
temperature-to-digital conversions yield the same
qualitative result. In other words, the value reported in
TEMP must remain above TSET or below THYST for the
consecutive number of cycles programmed in the Fault
Queue. Up to a six-cycle “filter” may be selected. See
Section 5.0 “Register Set and Programmer’s
ModeL”, Register Set and Programmer’s Model.
4.2
TABLE 4-1:
NOT Busy
When the bus is idle, both SDA & SCL will
remain high.
Data Valid
The state of SDA must remain stable during
the High period of SCL in order for a data bit
to be considered valid. SDA only changes
state while SCL is low during normal data
transfers. (See Start and Stop conditions).
All transfers take place under control of a host, usually
a CPU or microcontroller, acting as the Master, which
provides the clock signal for all transfers. The TCN75
always operates as a Slave. This serial protocol is
illustrated in Figure 5-1. All data transfers have two
phases; and all bytes are transferred MSB first.
Accesses are initiated by a Start condition, followed by
a device address byte and one or more data bytes. The
device address byte includes a Read/Write selection
bit. Each access must be terminated by a Stop condition. A convention called Acknowledge (ACK) confirms
receipt of each byte. Note that SDA can change only
during periods when SCL is LOW (SDA changes while
SCL is HIGH are reserved for Start and Stop conditions).
4.3
Start Condition (Start)
The TCN75 continuously monitors the SDA and SCL
lines for a Start condition (a HIGH-to-LOW transition of
SDA while SCL is HIGH), and will not respond until this
condition is met.
DS21490D-page 8
 2001-2012 Microchip Technology Inc.
TCN75
4.3.1
ADDRESS BYTE
Immediately following the Start condition, the host must
next transmit the address byte to the TCN75. The four
Most Significant bits of the Address Byte (A6, A5, A4,
A3) are fixed to 1001(B). The states of A2, A1 and A0
in the serial bit stream must match the states of the A2,
A1 and A0 address inputs for the TCN75 to respond
with an Acknowledge (indicating the TCN75 is on the
bus and ready to accept data). The eighth bit in the
Address Byte is a Read/Write Bit. This bit is a ‘1’ for a
read operation or ‘0’ for a write operation.
4.3.2
ACKNOWLEDGE (ACK)
Acknowledge (ACK) provides a positive handshake
between the host and the TCN75. The host releases
SDA after transmitting eight bits then generates a ninth
clock cycle to allow the TCN75 to pull the SDA line
LOW to acknowledge that it successfully received the
previous eight bits of data or address.
4.3.3
4.3.4
STOP CONDITION (STOP)
Communications must be terminated by a Stop
condition (a LOW-to-HIGH transition of SDA while SCL
is HIGH). The Stop condition must be communicated
by the transmitter to the TCN75.
4.3.5
POWER SUPPLY
To minimize temperature measurement error, the
TCN75-3.3 MOA and TCN75-3.3 MUA are factory calibrated at a supply voltage of 3.3V ±5% and the
TCN75-5.0 MOA and TCN75-5.0 MUA are factory calibrated at a supply voltage of 5V ±5%. Either device is
fully operational over the power supply voltage range of
2.7V to 5.5V, but with a lower measurement accuracy.
The typical value of this power supply-related error is
±2°C.
DATA BYTE
After a successful ACK of the address byte, the host
must next transmit the data byte to be written or clock
out the data to be read. (See the appropriate timing
diagrams.) ACK will be generated after a successful
write of a data byte into the TCN75.
 2001-2012 Microchip Technology Inc.
DS21490D-page 9
TCN75
5.0
REGISTER SET AND
PROGRAMMER’S MODEL
TABLE 5-1:
D[7] D[6]
D3 – D4: Fault Queue: Number of sequential
temperature-to-digital conversions with the same result
before the INT/CMPTR output is updated:
REGISTER (POINT), 8 BITS,
WRITE ONLY
D[5]
D[4]
D[3]
D[2]
D[1]
Must Be Set To Zero
D[0]
Pointer
Register Selection Via the Pointer Register
D1
D0
0
0
TEMP
0
1
CONFIG
1
0
THYST
1
1
TSET
D
[6]
D3
Number of Conversions
0
0
1 (Power-up default)
0
1
2
1
0
4
1
1
6
Register Selection
TABLE 5-2:
D
[7]
D4
CONFIGURATION REGISTER
(CONFIG), 8 BITS, READ/
WRITE
D
[5]
D
[4]
Must Be Set
To Zero
D
[3]
Fault
Queue
D
[2]
D
[1]
INT/
COM
CMPTR, P/INT
Polarity
D
[0]
Shutdown
D0: Shutdown:
0 = Normal Operation
1 = Shutdown Mode
D1: CMPTR/INT:
0 = Comparator Mode
1 = Interrupt Mode
D2: INT/CMPTR POLARITY:
0 = Active Low
1 = Active High
DS21490D-page 10
 2001-2012 Microchip Technology Inc.
TCN75
TABLE 5-3:
TEMPERATURE (TEMP) REGISTER, 16 BITS, READ ONLY
The binary value in this register represents ambient temperature following a conversion cycle.
D[15]
D[14]
D[13]
D[12]
D[11]
D[10]
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
MSB
D7
D6
D5
D4
D3
D2
D1
LSB
X
X
X
X
TABLE 5-4:
X
X
D[0]
X
TEMPERATURE SET POINT (TSET) REGISTER, 16 BITS, READ/WRITE
D[15]
D[14]
D[13]
D[12]
D[11]
D[10]
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
MSB
D7
D6
D5
D4
D3
D2
D1
LSB
X
X
X
X
TABLE 5-5:
D[2] D[1]
D[2] D[1]
X
X
D[0]
X
HYSTERESIS (THYST) REGISTER, 16 BITS, READ/WRITE
D[15]
D[14]
D[13]
D[12]
D[11]
D[10]
D[9]
D[8]
D[7]
D[6]
D[5]
D[4]
D[3]
MSB
D7
D6
D5
D4
D3
D2
D1
LSB
X
X
X
X
D[2] D[1]
X
X
D[0]
X
In the TEMP, TSET, and THYST registers, each unit
value represents one-half degree (Celsius). The value
is in 2’s – complement binary format such that a reading of 000000000b corresponds to 0°C. Examples of
this temperature to binary value relationship are shown
in Table 5-6.
TABLE 5-6:
TEMPERATURE TO DIGITAL
VALUE CONVERSION
Temperature
Binary Value
HEX Value
+125°C
0 11111010
0FA
+25°C
0 00110010
032
+0.5°C
0 00000001
001
0°C
0 00000000
00
0.5°C
1 11111111
1FF
-25°C
1 11001110
1CE
-40°C
1 10110000
1B0
-55°C
1 10010010
192
TABLE 5-7:
TCN75’S REGISTER SET SUMMARY
Name
Description
Width
Read
Write
TEMP
Ambient Temperature
16
X
TSET
Temperature Setpoint
16
X
X
2’s Complement Format
2’s Complement Format
2’s Complement Format
THYST
Temperature Hysteresis
16
X
X
POINT
Register Pointer
8
X
X
CONFIG
Configuration Register
8
X
X
 2001-2012 Microchip Technology Inc.
Notes
DS21490D-page 11
TCN75
9
1
1
0
Start
by
Master
0
1
D7 D6 D5 D4 D3 D2 D1 D0
1 A2 A1 A0 R/W
Ack
by
Address Byte
9
Most Significant Data Byte
TCN75
1
9
D7 D6 D5 D4 D3 D2 D1 D0
Ack
Least Significant Data Byte
by
Master
Stop
No Ack Cond
by
by
Master Master
(a) Typical 2-Byte Read From Preset Pointer Location Such as Temp, TOS, THYST
9
1
1
9
.....
1
0
Start
by
Master
0
1 A2 A1 A0 R/W
0
0
Ack
by
Address Byte
0
0
0
TCN75
9
1
1
Repeat
Start
by
Master
0
0
Ack
by
Pointer Byte
TCN75
1 A2 A1 A0 R/W
1
9
D7 D6 D5 D4 D3 D2 D1 D0
Ack
by
Address Byte
.....
0 D1 D0
Most Significant Data Byte
TCN75
1
9
D7 D6 D5 D4 D3 D2 D1 D0
Ack
Least Significant Data Byte
by
Master
Stop
No Ack Cond
by
by
Master Master
(b) Typical Pointer Set Followed by Immediate Read for 2-Byte Register Such as Temp, TOS, THYST
1
1
9
0
Start
by
Master
0
1 A2 A1 A0 R/W
Address Byte
1
9
D7 D6 D5 D4 D3 D2 D1 D0
Ack
by
Data Byte
TCN75T
Stop
No Ack Cond
by
by
Master Master
(c) Typical 1-Byte Read From Configuration Register with Preset Pointer
FIGURE 5-1:
DS21490D-page 12
Timing Diagrams
 2001-2012 Microchip Technology Inc.
 2001-2012 Microchip Technology Inc.
0
0
1 A2 A1 A0 R/W
Ack
by
9
0
1
0
0
0
0
0
0 D0
9
1
1
1
0
1
0
0
1
Ack
by
9
0
1
TCN75
1 A2 A1 A0 R/W
Address Byte
0
(f) TOS and THYST Write
Start
by
Master
1
Ack
by
9
TCN75T
1 A2 A1 A0 R/W
Address Byte
0
(e) Configuration Register Write
Start
by
Master
1
0
0
0
0
0
0
Pointer Byte
0
Pointer Byte
0
Ack
by
0
1
1
0
1
Configuration Byte
Most Significant Data Byte
Ack
by
9
Stop
Cond
by
Master
Least Significant Data Byte
Ack
by
9
Stop
Cond
by
Master
Stop
No Ack Cond
by
by
Master Master
9
TCN75
D7 D6 D5 D4 D3 D2 D1 D0
1
TCN75
Ack
by
9
TCN75
Ack
by
9
Data Byte
D7 D6 D5 D4 D3 D2 D1 D0
1
TCN75
A2 A1 A0 R/W
Address Byte
0
0 D4 D3 D2 D1 D0
0
D7 D6 D5 D4 D3 D2 D1 D0
TCN75
Ack
by
0 D1 D0
9
TCN75
0 D1 D0
9
Ack Repeat
Address Byte
Pointer Byte
by Start
TCN75
TCN75 by
Master
(d) Typical Pointer Set Followed by Immediate Read from Configuration Register
Start
by
Master
1
1
TCN75
Timing Diagrams (Continued)
DS21490D-page 13
TCN75
6.0
PACKAGING INFORMATION
6.1
Package Marking Information
Package marking data not available at this time.
6.2
Taping Form
Component Taping Orientation for 8-Pin MSOP Devices
User Direction of Feed
Pin 1
W
P
Standard Reel Component Orientation
for 713 Suffix Device
Carrier Tape, Number of Components Per Reel and Reel Size
Package
8-Pin MSOP
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
12 mm
8 mm
2500
13 in
Component Taping Orientation for 8-Pin SOIC (Narrow) Devices
User Direction of Feed
Pin1
W
P
Standard Reel Component Orientation
for 713 Suffix Device
Carrier Tape, Number of Components Per Reel and Reel Size
Package
8-Pin SOIC (N)
DS21490D-page 14
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
12 mm
8 mm
2500
13 in
 2001-2012 Microchip Technology Inc.
TCN75
6.3
Package Dimensions
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
8-Pin MSOP
Pin 1
.122 (3.10) .197 (5.00)
.114 (2.90) .189 (4.80)
.026 (0.65) Typ.
.122 (3.10)
.114 (2.90)
.043 (1.10)
Max.
.016 (0.40)
.010 (0.25) .002 (0.05)
.008 (0.20)
.005 (0.13)
6° Max.
.006 (0.15)
.028 (0.70)
.016 (0.40)
Dimensions: inches (mm)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located
at http://www.microchip.com/packaging
8-Pin SOIC
Pin 1
.157 (3.99)
.150 (3.81)
.244 (6.20)
.228 (5.79)
.050 (1.27) Typ.
.197 (5.00)
.189 (4.80)
.069 (1.75)
.053 (1.35)
.020 (0.51) .010 (0.25)
.013 (0.33) .004 (0.10)
.010 (0.25)
.007 (0.18)
8° Max.
.050 (1.27)
.016 (0.40)
Dimensions: inches (mm)
 2001-2012 Microchip Technology Inc.
DS21490D-page 15
TCN75
7.0
REVISION HISTORY
Revision D (December 2012)
Added a note to each package outline drawing.
DS21490D-page 16
 2001-2012 Microchip Technology Inc.
TCN75
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://microchip.com/support
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
 2001-2012 Microchip Technology Inc.
DS21490D-page 17
TCN75
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: TCN75
Literature Number: DS21490D
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS21490D-page 18
 2001-2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. & KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2001-2012, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 9781620768815
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
 2001-2012 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS21490D-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS21490D-page 20
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
11/29/12
 2001-2012 Microchip Technology Inc.