Download

Safety Network Controller
NE0A-SCPU01
CSM_NE0A-SCPU01_DS_E_6_3
New Lineup for Safety Applications
with Up to 12 Inputs
• Circuits for the required safety category are easy to build.
• The safety circuits you create can be registered as templates
and reused, for easy standardization.
• A wide range of TÜV-certified templates is also available.
• The NE0A operating conditions can be monitored from a
standard DeviceNet Master.
• Network distribution is possible by combining with an NE1A
Safety Controller.
• ISO13849-1 (PLe) and IEC 61508 SIL3 certification.
Ordering Information
Name
No. of I/O points
Safety inputs
Test outputs
Model
Safety outputs
Unit version
Safety Network Controllers
12 *
2
6
NE0A-SCPU01
Ver. 1.0
Note: 1. The standard NE0A Safety Network Controller is equipped with spring-cage terminal blocks, but screw terminal blocks are available if
desired, e.g., to replace previous terminals.
2. Network Configurator version 2.1@ or higher must be used when using a NE0A-SCPU01 Safety Network Controller.
* When using the NE0A-SCPU01 as a standalone Controller, one input each is required for the feedback input and manual restart.
Specifications
Certified Standards
Certification
body
TÜV Rheinland
UL
Specifications
Standard
NFPA 79-2012
EN ISO13849-1: 2006
IEC61508 part1-7: 2010
IEC61131-2:2007
EN ISO13849-2:2003
EN ISO 13850:2006 (EN418: 1992)
EN61000-6-4:2007
EN61000-6-2:2005
EN60204-1:2006
ANSI RIA15.06-1999
ANSI B11.19-2010
UL508
ANSI/ISA 12.12.01
UL1998
NFPA79
IEC61508
CSA22.2 No.142
CSA22.2 No.213
Communications
11 to 25 VDC supplied via communicapower supply voltage tions connector
Internal circuit power
supply voltage (V0) *1
I/O power supply
voltage (V1, V2) *1
Communications power
supply
Current
Internal circoncuit power
sumpsupply
tion
I/O power
supply *2
20.4 to 26.4 VDC (24 VDC −15%/+10%)
24 VDC, 15 mA
24 VDC, 110 mA
24 VDC, 80 mA (Input)
80 mA (Output)
Overvoltage category II
Noise immunity
Conforms to IEC61131-2.
Vibration resistance
10 to 57 Hz: 0.35 mm,
57 to 150 Hz: 50 m/s2
Shock resistance
150 m/s2 : 11 ms
Mounting method
DIN Track (IEC 60715 TH35-7.5/TH35-15)
Ambient operating
temperature
−10 to 55°C
Ambient operating
humidity
10% to 95% (with no condensation)
Ambient storage tem−40 to 70°C
perature
Degree of protection
IP20
Serial I/F
USB version 1.1
Weight
440 g max.
*1. V0-G0: Internal control circuit
V1-G1: For external input device, test output
V2-G2: For external output device
*2. Not including power consumption for external devices.
1
NE0A-SCPU01
Safety Input Specifications
Test Output Specifications
Input type
Sinking inputs (PNP)
Output type
Sourcing outputs (PNP)
ON voltage
11 VDC min. between each terminal and ground
60 mA
OFF voltage
5 VDC max. between each terminal and ground
Rated output
current
OFF current
1 mA max.
1.2 V max. between each output terminal and V1
Input current
4.5 mA
ON residual
voltage
Leakage current 0.1 mA max.
Safety Output Specifications
Output type
Sourcing outputs (PNP)
Rated output
current
0.5 A max./output
ON residual
voltage
1.2 V max. between each output terminal and V2
Leakage current 0.1 mA max.
DeviceNet Communications Specifications
Communications
protocol
DeviceNet compliant
Connection form
Multi-drop system and T-branch system can be combined (for trunk line and branch lines)
Communications speed
500/250/125 kbps
Communications media
Special cable, 5 conductors (2 for communications, 2 for power supply, 1 for shielding)
Communications speed
Max. network length
500 kbps
100 m max. (100 m max.)
250 kbps
250 m max. (100 m max.)
125 kbps
500 m max. (100 m max.)
Communications
distance
Branch length
Total branch length
39 m max.
6 m max.
78 m max.
156 m max.
Note: Figures in parentheses ( ) indicate values when a thin cable is used.
Communications power
11 to 25 VDC
supply
No. of connectable
nodes
63
Safety I/O communications
Safety Slave function
• Max. no. of connections: 2 (one each for inputs and outputs)
Multi-cast inputs can be used to enable communications with up to 15 Safety Masters.
• Connection type: Single-cast, multi-cast
Standard I/O communications
Standard Slave function
• Max. no. of connections: 2
• Connection type: Poll, bit-strobe, COS, cyclic
Message communications
Max. message length: 502 bytes
2
NE0A-SCPU01
Functions
The following function blocks are available for designing safety circuits with the NE0A-SCPU01. These function blocks can be selected and
assembled using the interactive wizard format to efficiently design safety applications.
Classification of function
block for safety circuit
designs
Application
The following six parts can be selected for use as safety input devices.
For Category 3 or 4 compliance, the filter monitoring time between signals can also be adjusted with redundant
wiring for the necessary safety devices.
Function blocks for safety
input devices and setting input filter times
Emergency Stop Switches
Safety Door Switches
Limit Switches
Safety Light Curtains
Enabling Switches
Mode Selectors
Select a Safety Light Curtain as the safety input device, and select a muting function when required.
No setting
Logic function blocks for input conditions
Uses the ON/OFF status from the safety input device exactly as it is.
OR operation
AND/OR operations
AND operation
For switching maintenance areas with a Mode Selector.
For applications such as a Safety Light Curtain muting function.
OR/AND operations
Function blocks for resets
Selects manual or auto reset.
For applications such as stopping all outputs for multiple safety devices.
Logic function blocks for
output conditions
No setting
AND operation
OR/AND operations
Uses the ON/OFF status of the safety signal exactly as it is.
Selects the interlock conditions for the safety signal.
Used to check the safety condition of an output device.
Function blocks for setting
the welded contact check
No setting
No checking of the output device (used for Category 2 or lower).
EDM
Used to check for contact welding in a Relay or Contactor.
Also used to change the setting for monitoring time.
Function blocks for safety
Logic
output devices and setting
For setting an auxiliary output (to output an error condition) and for setting the output delay.
output delay times
Note: There is a possibility that safety cannot be maintained when an OR part or an AND/OR part is selected for input logic, or an OR/AND part
is selected for output logic. Sufficiently confirm safety prior to use.
3
NE0A-SCPU01
Internal Circuit Diagrams
DC-DC Converter
(Non-insulated)
NE0A-SCPU01
V0
24 VDC
G0
V1
V+
DeviceNet
Physical Layer
CAN H
Shield
CAN L
24 VDC
G1
T0
T1
IN0
Safety Input Circuit
Test Output Circuit
Internal Circuit
DC-DC Converter
(Non-insulated)
V−
IN8
T0
T1
IN9
IN10
IN11
24 VDC
Safety Output Circuit
V2
D+
USB
D−
Terminal No.
Terminal name
---
V0
---
G0
1
V1
11
G1
24
V2
34
G2
2 to 10
IN0 to IN8
21 to 23
IN9 to IN11
12 to 20
31 to 33
T0 to T1
25 to 30
OUT0 to OUT5
35 to 40
G2
G2
OUT0
OUT5
L
L
Description
Power supply terminal for internal circuit (24 VDC)
Power supply terminal for external input device and test output (24 VDC)
Power supply terminal for external output device (24 VDC)
Safety input terminal
Terminals IN10 and IN11 are used only for connecting a reset switch or EDM feedback.
Test output terminal
Connected to IN0 to IN11 safety inputs.
T0 and T1 output test pulses with different patterns.
The T0 terminals are internally connected and the T1 terminals are internally connected.
Safety output terminals
Common terminal
Terminals 34 to 40 are internally connected.
4
NE0A-SCPU01
Dimensions
(Unit: mm)
NE0A-SCPU01
(90)
71.4
80
190
Safety Precautions
Refer to the "Safety Precautions for All CIP Safety on DeviceNet Systems" for precautions.
Be sure to read the following user's manual for other details required for correct use of the Safety Network
Controller.
CIP Safety on DeviceNet Safety Network Controller NE0A Series User's Manual (Cat. No. Z916)
5
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2013.12
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2013 All Right Reserved.