REVISIONS LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV PAGE REV PAGE 18 19 REV STATUS OF PAGES 20 21 22 REV PAGE 1 2 PMIC N/A PREPARED BY RICK OFFICER Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA 13-07-02 4 A REV 5 6 7 8 9 10 11 12 13 14 15 16 17 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil/ TITLE MICROCIRCUIT, LINEAR, LOW POWER OUTPUT AMPLIFIERS, MONOLITHIC SILICON APPROVED BY CHARLES F. SAFFLE SIZE AMSC N/A 3 CODE IDENT. NO. DWG NO. V62/13614 16236 PAGE 1 OF 22 5962-V057-13 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low power output amplifiers microcircuit, with an operating temperature range of -55°C to +125°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/13614 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 02 Circuit function ADA4897-1-EP ADA4897-2-EP Single low power output amplifier Dual low power output amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins X Y 6 10 JEDEC PUB 95 Package style MO-178-AB MO-187-BA Plastic small outline package Plastic small outline package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z DLA LAND AND MARITIME COLUMBUS, OHIO Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 2 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) .................................................................................................... 11 V Common mode input voltage (VCM) ........................................................................... Differential input voltage ............................................................................................. Power dissipation (PD) : Device type 01 ....................................................................................................... Device type 02 ....................................................................................................... Storage temperature range (TSTG) ............................................................................ Lead temperature (soldering 10 seconds) .................................................................. Junction temperature range (TJ) ................................................................................ -VS – 0.7 V to +VS + 0.7 V ±0.7 V 166.6 mW 2/ 119.0 mW 2/ -65°C to +125°C +300°C +150°C 1.4 Recommended operating conditions. 3/ Supply voltage range (VS) .......................................................................................... -5 V to +5 V Operating free-air temperature range (TA) ................................................................. -55°C to +125°C 1.5 Thermal characteristics. Thermal resistance, junction to ambient (θJA): X package ............................................................................................................... 150°C/W Y package ............................................................................................................... 210°C/W 1/ 2/ 3/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. For device type 01, power dissipation (PD) = ( TJ max – TA ) / θJA = (150 – 125) / 150 = 0.16666 W. For device type 02, power dissipation (PD) = ( TJ max – TA ) / θJA = (150 – 125) / 210 = 0.1190 W. Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 3 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 4 TABLE I. Electrical performance characteristics. 1/ 2/ Test Symbol Conditions VS = ±5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to ground, unless otherwise specified Unit Max Dynamic performance section. -3 dB bandwidth BW Bandwidth for 0.1 dB flatness +25°C G = +1, VOUT = 0.02 VPP 01, 02 230 typical G = +1, VOUT = 2 VPP 30 typical G = +2, VOUT = 0.02 VPP 90 typical G = +2, VOUT = 2 VPP, MHz +25°C 01, 02 7 typical MHz RL = 100 Ω Slew rate SR G = +2, VOUT = 6 V step +25°C 01, 02 120 typical V/µs Settling time to 0.1% tS G = +2, VOUT = 2 V step +25°C 01, 02 45 typical ns Settling time to 0.01% tS G = +2, VOUT = 2 V step +25°C 01, 02 90 typical ns +25°C 01, 02 -115 typical dBc Noise / harmonic performance section. Harmonic distortion SFDR Input voltage noise VOUT = 2 VPP, fC = 100 kHz VOUT = 2 VPP, fC = 1 MHz -93 typical VOUT = 2 VPP, fC = 2 MHz -80 typical VOUT = 2 VPP, fC = 5 MHz -61 typical f = 10 Hz +25°C 01, 02 f = 100 kHz Input current noise nV / Hz 1 typical f = 10 Hz +25°C 01, 02 f = 100 kHz 0.1 Hz to 10 Hz noise 2.4 typical 11 typical pA / Hz 2.8 typical G = +101, RF = 1 kΩ, RG = 10 Ω +25°C 01, 02 99 typical nVPP See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 5 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions VS = ±5 V, G = +1, Temperature, TA Device type RL = 1 kΩ to ground, unless otherwise specified Limits Unit Min Max -500 +500 DC performance section. Input offset voltage +25°C VIO 01, 02 µV -28 typical Input offset voltage drift ∆VIO +25°C 01, 02 Input bias current IIB +25°C 01, 02 0.2 typical -17 µV / °C µA -4 -11 typical Input bias current drift ∆IIB +25°C 01, 02 Input bias offset current IIBO +25°C 01, 02 3 typical -0.6 nA / °C µA +0.6 -0.02 typical Open loop gain AOL +25°C VOUT = -4 V to +4 V 01, 02 100 dB 110 typical Input characteristics section. Input resistance, common mode RIN +25°C 01, 02 10 typical MΩ Input resistance, differential RIN +25°C 01, 02 10 typical kΩ Input capacitance, common mode CIN +25°C 01, 02 3 typical pF Input capacitance, differential CIN +25°C 01, 02 11 typical pF Input common mode voltage range VINR +25°C 01, 02 -4.9 to +4.1 typical V Common mode rejection ratio CMRR +25°C 01, 02 VCM = -2 V to +2 V -92 dB -120 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 6 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions VS = ±5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to ground, unless otherwise specified Unit Max Output characteristics section. Output overdrive recovery time VIN = ±5 V, G = + 2 +25°C 01, 02 Positive output voltage swing RL = 1 kΩ +25°C 01, 02 81 typical ns 4.85 V 4.96 typical 4.5 RL = 100 Ω 4.73 typical Negative output voltage swing +25°C RL = 1 kΩ 01, 02 -4.85 V -4.97 typical -4.5 RL = 100 Ω -4.84 typical Output current IOUT SFDR = -45 dBc +25°C 01, 02 80 typical mA Short circuit current ISC Sinking / sourcing +25°C 01, 02 135 typical mA 30% overshoot, G = +2 +25°C 01, 02 39 typical pF Operating range +25°C 01, 02 3 to 10 typical V Quiescent current per amplifier +25°C 01, 02 2.8 Capacitive load drive Power supply section. 3.2 mA 3.0 typical 0.25 DISABLE = -5 V 0.13 typical Power supply rejection ratio +PSRR +25°C +VS = 4 V to 6 V, -VS = -5 V 01, 02 -96 dB -125 typical -PSRR -96 +VS = 5 V, -VS = -4 V to -6 V -121 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 7 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions VS = ±5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to ground, unless otherwise specified Unit Max DISABLE pin section. Enabled DISABLE voltage +25°C 01, 02 Disabled V >+VS – 0.5 typical <+VS – 2 typical Input current, enabled IIN DISABLE = +5 V +25°C 01, 02 -1.2 typical µA Input current, disabled IIN DISABLE = -5 V +25°C 01, 02 -40 typical µA Switching speed, enabled +25°C 01, 02 0.25 typical µs Switching speed, disabled +25°C 01, 02 12 typical µs See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 8 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max Dynamic performance section. -3 dB bandwidth BW Bandwidth for 0.1 dB flatness +25°C G = +1, VOUT = 0.02 VPP 01, 02 230 typical G = +1, VOUT = 2 VPP 30 typical G = +2, VOUT = 0.02 VPP 90 typical G = +2, VOUT = 2 VPP, MHz +25°C 01, 02 7 typical MHz RL = 100 Ω Slew rate SR G = +2, VOUT = 3 V step +25°C 01, 02 100 typical V/µs Settling time to 0.1% tS G = +2, VOUT = 2 V step +25°C 01, 02 45 typical ns Settling time to 0.01% tS G = +2, VOUT = 2 V step +25°C 01, 02 95 typical ns +25°C 01, 02 -115 typical dBc Noise / harmonic performance section. Harmonic distortion SFDR Input voltage noise VOUT = 2 VPP, fC = 100 kHz VOUT = 2 VPP, fC = 1 MHz -93 typical VOUT = 2 VPP, fC = 2 MHz -80 typical VOUT = 2 VPP, fC = 5 MHz -61 typical f = 10 Hz +25°C 01, 02 f = 100 kHz Input current noise nV / Hz 1 typical f = 10 Hz +25°C 01, 02 f = 100 kHz 0.1 Hz to 10 Hz noise 2.4 typical 11 typical pA / Hz 2.8 typical G = +101, RF = 1 kΩ, RG = 10 Ω +25°C 01, 02 99 typical nVPP See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 9 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +5 V, G = +1, Temperature, TA Device type RL = 1 kΩ to midsupply, unless otherwise specified Limits Unit Min Max -500 +500 DC performance section. Input offset voltage +25°C VIO 01, 02 µV -30 typical Input offset voltage drift ∆VIO +25°C 01, 02 Input bias current IIB +25°C 01, 02 0.2 typical -17 -4 µV / °C µA -11 typical Input bias current drift ∆IIB +25°C 01, 02 Input bias offset current IIBO +25°C 01, 02 3 typical -0.6 +0.6 nA / °C µA -0.02 typical Open loop gain AOL +25°C VOUT = 0.5 V to 4.5 V 01, 02 97 dB 110 typical Input characteristics section. Input resistance, common mode RIN +25°C 01, 02 10 typical MΩ Input resistance, differential RIN +25°C 01, 02 10 typical kΩ Input capacitance, common mode CIN +25°C 01, 02 3 typical pF Input capacitance, differential CIN +25°C 01, 02 11 typical pF Input common mode voltage range VINR +25°C 01, 02 0.1 to 4.1 typical V Common mode rejection ratio CMRR +25°C 01, 02 VCM = 1 V to 4 V -91 dB -118 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 10 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max Output characteristics section. Output overdrive recovery time VIN = 0 V to 5 V, G = + 2 +25°C 01, 02 Positive output voltage swing RL = 1 kΩ +25°C 01, 02 96 typical 4.85 ns V 4.98 typical 4.8 RL = 100 Ω 4.88 typical Negative output voltage swing +25°C RL = 1 kΩ 01, 02 0.15 V 0.014 typical 0.2 RL = 100 Ω 0.08 typical Output current IOUT SFDR = -45 dBc +25°C 01, 02 70 typical mA Short circuit current ISC Sinking / sourcing +25°C 01, 02 125 typical mA 30% overshoot, G = +2 +25°C 01, 02 39 typical pF Operating range +25°C 01, 02 3 to 10 typical V Quiescent current per amplifier +25°C 01, 02 2.6 Capacitive load drive Power supply section. 2.9 mA 2.8 typical 0.18 DISABLE = 0 V 0.05 typical Power supply rejection ratio +PSRR +25°C +VS = 4.5 V to 5.5 V, -VS = 0 V 01, 02 -96 dB -123 typical -PSRR -96 +VS = 5 V, -VS = -0.5 V to +0.5 V -121 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 11 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +5 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max DISABLE pin section. Enabled DISABLE voltage +25°C 01, 02 Disabled >+VS – 0.5 typical V <+VS – 2 typical Input current, enabled IIN DISABLE = +5 V +25°C 01, 02 -1.2 typical µA Input current, disabled IIN DISABLE = 0 V +25°C 01, 02 -20 typical µA Switching speed, enabled +25°C 01, 02 0.25 typical µs Switching speed, disabled +25°C 01, 02 12 typical µs See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 12 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +3 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max Dynamic performance section. -3 dB bandwidth BW Bandwidth for 0.1 dB flatness +25°C G = +1, VOUT = 0.02 VPP 01, 02 230 typical G = -1, VOUT = 1 VPP 45 typical G = +2, VOUT = 0.02 VPP 90 typical G = +2, VOUT = 2 VPP, MHz +25°C 01, 02 7 typical MHz RL = 100 Ω Slew rate SR G = +2, VOUT = 1 V step +25°C 01, 02 85 typical V/µs Settling time to 0.1% tS G = +2, VOUT = 2 V step +25°C 01, 02 45 typical ns Settling time to 0.01% tS G = +2, VOUT = 2 V step +25°C 01, 02 96 typical ns +25°C 01, 02 -105 typical dBc Noise / harmonic performance section. Harmonic distortion SFDR Input voltage noise VOUT = 2 VPP, fC = 100 kHz, G = +2 VOUT = 1 VPP, fC = 1 MHz, G = -1 -84 typical VOUT = 1 VPP, fC = 2 MHz, G = -1 -77 typical VOUT = 1 VPP, fC = 5 MHz, G = -1 -60 typical f = 10 Hz +25°C 01, 02 f = 100 kHz Input current noise 1 typical f = 10 Hz +25°C 01, 02 f = 100 kHz 0.1 Hz to 10 Hz noise 2.3 typical 11 typical 2.8 typical G = +101, RF = 1 kΩ, RG = 10 Ω +25°C 01, 02 99 typical nV / Hz pA / Hz nVPP See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 13 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +3 V, G = +1, Temperature, TA Device type Limits RL = 1 kΩ to midsupply, unless otherwise specified Unit Min Max -500 +500 DC performance section. Input offset voltage +25°C VIO 01, 02 µV -30 typical Input offset voltage drift ∆VIO +25°C 01, 02 Input bias current IIB +25°C 01, 02 0.2 typical -17 -4 µV / °C µA -11 typical Input bias current drift ∆IIB +25°C 01, 02 Input bias offset current IIBO +25°C 01, 02 3 typical -0.6 +0.6 nA / °C µA -0.02 typical Open loop gain AOL +25°C VOUT = 0.5 V to 2.5 V 01, 02 95 dB 108 typical Input characteristics section. Input resistance, common mode RIN +25°C 01, 02 10 typical MΩ Input resistance, differential RIN +25°C 01, 02 10 typical kΩ Input capacitance, common mode CIN +25°C 01, 02 3 typical pF Input capacitance, differential CIN +25°C 01, 02 11 typical pF Input common mode voltage range VINR +25°C 01, 02 0.1 to 2.1 typical V Common mode rejection ratio CMRR +25°C 01, 02 VCM = 1.1 V to 1.9 V -90 dB -124 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 14 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +3 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max Output characteristics section. Output overdrive recovery time VIN = 0 V to 3 V, G = + 2 +25°C 01, 02 Positive output voltage swing RL = 1 kΩ +25°C 01, 02 83 typical 2.85 ns V 2.97 typical 2.8 RL = 100 Ω 2.92 typical Negative output voltage swing +25°C RL = 1 kΩ 01, 02 0.15 V 0.01 typical 0.2 RL = 100 Ω 0.05 typical Output current IOUT SFDR = -45 dBc +25°C 01, 02 60 typical mA Short circuit current ISC Sinking / sourcing +25°C 01, 02 120 typical mA 30% overshoot, G = +2 +25°C 01, 02 39 typical pF Operating range +25°C 01, 02 3 to 10 typical V Quiescent current per amplifier +25°C 01, 02 2.5 Capacitive load drive Power supply section. 2.9 mA 2.7 typical 0.15 DISABLE = 0 V 0.035 typical Power supply rejection ratio +PSRR +25°C +VS = 2.7 V to 3.7 V, -VS = 0 V 01, 02 -96 dB -121 typical -PSRR -96 +VS = 3 V, -VS = -0.3 V to +0.7 V -120 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 15 TABLE I. Electrical performance characteristics – Continued. 1/ 2/ Test Symbol Conditions 2/ VS = +3 V, G = +1, Temperature, TA Device type Limits Min RL = 1 kΩ to midsupply, unless otherwise specified Unit Max DISABLE pin section. Enabled DISABLE voltage +25°C 01, 02 Disabled >+VS – 0.5 typical V <+VS + 2 typical Input current, enabled IIN DISABLE = +3 V +25°C 01, 02 -1.2 typical µA Input current, disabled IIN DISABLE = 0 V +25°C 01, 02 -15 typical µA Switching speed, enabled +25°C 01, 02 0.25 typical µs Switching speed, disabled +25°C 01, 02 12 typical µs 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Products supplied to this drawing have been characterized across the military temperature range of -55°C to +125°C but, are only production tested at +25°C. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 16 Case X FIGURE 1. Case outlines. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 17 Case X – continued. Dimensions Inches Symbol Millimeters Min Med Max Min Med Max A 0.035 0.045 0.051 0.90 1.15 1.30 A1 0.001 --- 0.005 0.05 --- 0.15 A2 0.037 --- 0.057 0.95 --- 1.45 b 0.011 --- 0.019 0.30 --- 0.50 c 0.003 --- 0.007 0.08 --- 0.20 D 0.110 0.114 0.118 2.80 2.90 3.00 E 0.059 0.062 0.066 1.50 1.60 1.70 E1 0.102 0.110 0.118 2.60 2.80 3.00 e L L1 0.037 BSC 0.013 0.017 0.95 BSC 0.021 0.35 0.023 BSC 0.45 0.55 0.60 BSC NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within reference to JEDEC MO-178-AB. FIGURE 1. Case outlines - continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 18 Case Y FIGURE 1. Case outlines - Continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 19 Case Y – continued. Dimensions Inches Symbol Millimeters Min Med Max Min Med Max A --- --- 0.043 --- --- 1.10 A1 0.001 --- 0.005 0.05 --- 0.15 A2 0.029 0.033 0.037 0.75 0.85 0.95 b 0.05 --- 0.011 0.15 --- 0.30 c 0.005 --- 0.009 0.13 --- 0.23 D 0.114 0.118 0.122 2.90 3.00 3.10 E 0.114 0.118 0.122 2.90 3.00 3.10 E1 0.183 0.192 0.202 4.65 4.90 5.15 e L 0.019 BSC 0.015 0.021 0.50 BSC 0.027 0.40 0.55 0.70 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within reference to JEDEC MO-187-BA. FIGURE 1. Case outlines - Continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 20 Device type 01 Case outline X Terminal number Terminal symbol Description 1 OUT Output. 2 -VS Negative supply. 3 +IN Noninverting input. 4 -IN Inverting input. 5 DISABLE 6 +VS Disable. Positive supply. Device type 02 Case outline Y Terminal number Terminal symbol Description 1 OUT1 2 -IN1 Inverting input 1. 3 +IN1 Noninverting input 1. 4 -VS Negative supply. 5 DISABLE1 Disable 1. 6 DISABLE2 Disable 2. 7 +IN2 Noninverting input 2. 8 -IN2 Inverting input 2. 9 OUT2 10 +VS Output 1. Output 2. Positive supply. FIGURE 2. Terminal connections. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 21 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number V62/13614-01XE 24355 ADA4897-1SRJZ-EPR7 V62/13614-02YE 24355 ADA4897-2TRMZ-EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code 24355 DLA LAND AND MARITIME COLUMBUS, OHIO Source of supply Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13614 PAGE 22