REVISIONS LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 PMIC N/A PREPARED BY RICK OFFICER Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA 13-05-29 4 A REV 5 6 7 8 9 10 11 12 13 14 15 16 17 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil/ TITLE MICROCIRCUIT, LINEAR, LOW NOISE, HIGH SPEED DIFFERENTIAL AMPLIFIER, MONOLITHIC SILICON APPROVED BY CHARLES F. SAFFLE SIZE AMSC N/A 3 CODE IDENT. NO. DWG NO. V62/13615 16236 PAGE 1 OF 17 5962-V058-13 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low noise, high speed differential amplifier microcircuit, with an operating temperature range of -55°C to +105°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/13615 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 Circuit function ADA4930-1-EP Low noise, high speed differential amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins X 16 JEDEC PUB 95 Package style MO-220-WEED Lead frame chip scale 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z 1.3 Absolute maximum ratings. Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other 1/ Supply voltage range (VS) .......................................................................................... 5.5 V Power dissipation (PD) at TA = +105°C ...................................................................... 550 mW Junction temperature range (TJ) ................................................................................ 150°C Storage temperature range (TSTG) ............................................................................. -65°C to +125°C Lead temperature (soldering, 10 seconds) ................................................................. 300°C 1.4 Recommended operating conditions. 2/ Supply voltage range (VS) .......................................................................................... 3.3 V to 5 V Operating free-air temperature range (TA) ................................................................. -55°C to +105°C 1/ 2/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 2 1.5 Thermal characteristics. Thermal resistance, junction to ambient (θJA) ............................................................ 81.6°C/W 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier and H2X ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 3 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/ VS = 3.3 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Dynamic performance. -3 dB small signal bandwidth SSBW VO,dm = 0.1 VP-P +25°C 01 1430 typical MHz -3 dB large signal bandwidth LSBW VO,dm = 2 VP-P +25°C 01 887 typical MHz VO,dm = 0.1 VP-P +25°C 01 380 typical MHz Bandwidth for 0.1 dB flatness Slew rate SR VO,dm = 2 V step, 25% to 75% +25°C 01 2877 typical V/µs Settling time to 0.1% tS VO,dm = 2 V step, RL = 200 Ω +25°C 01 6.3 typical ns G = 3, VIN,dm = 0.7 VP-P pulse +25°C 01 1.5 typical ns -55°C to +105°C 01 -98 typical dBc Overdrive recovery time Noise / harmonic performance. Second harmonic distortion Third harmonic distortion HD2 HD3 Third order intermodulation distortion (IMD) VO,dm = 2 VP-P, fC = 10 MHz VO,dm = 2 VP-P, fC = 30 MHz -91 typical VO,dm = 2 VP-P, fC = 70 MHz -79 typical VO,dm = 2 VP-P, fC = 100 MHz -73 typical -55°C to +105°C VO,dm = 2 VP-P, fC = 10 MHz 01 -97 typical VO,dm = 2 VP-P, fC = 30 MHz -88 typical VO,dm = 2 VP-P, fC = 70 MHz -79 typical VO,dm = 2 VP-P, fC = 100 MHz -73 typical +25°C VO,dm = 1 VP-P / tone, 01 91 typical dBc dBc fC = 70.05 MHz ±0.05 MHz 86 typical VO,dm = 1 VP-P / tone, fC = 140.05 MHz ±0.05 MHz See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 4 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 3.3 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Noise / harmonic performance - continued. Input voltage noise f = 100 kHz +25°C 01 -55°C to +105°C Input current noise f = 100 kHz +25°C 01 1.15 typical nV / 1.2 typical Hz 3 typical pA / Hz DC performance. Input offset voltage VIO VIP = VIN = VOCM = 0 V, -55°C to +105°C 01 -3.1 +3.1 mV -55°C to +105°C 01 +25°C 01 -36 -16 µA -0.05 typical µA / °C RL = open circuit Input offset voltage drift ∆VIO Input bias current IIB Input bias current drift ∆IIB -55°C to +105°C 01 Input offset current IIO +25°C 01 +25°C 01 Open loop gain RF = RG = 10 kΩ, ∆VO = 0.5 V, -1.8 +1.8 64 typical µV / °C µA dB 61 typical -55°C to +105°C RL = open circuit 2.75 typical Input characteristics. Input common mode voltage range Input resistance RIN Differential +25°C 01 +25°C 01 Common mode 0.3 1.2 V 150 typical kΩ 3 typical MΩ See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 5 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 3.3 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Input characteristics – continued. Input capacitance CIN Common mode +25°C 01 Common mode rejection mode CMRR ∆VICM = 0.5 V dc; +25°C 01 RF = RG = 10 kΩ, RL = open circuit 1 typical -77 pF dB -76 typical -55°C to +105°C Output characteristics. Output voltage VOUT Each single ended output, +25°C 01 0.11 V 1.54 -55°C to +105°C RF = RG = 10 kΩ 1.74 Linear output current Each single ended output, f = 1 MHz, THD ≤ 60 dBc +25°C 01 30 typical mA Output balance error f = 1 MHz +25°C 01 55 typical dB VO,CM = 0.1 VP-P +25°C 01 745 typical MHz VO,CM = 2 VP-P , 25% to 75% +25°C 01 828 typical V/µs 3.3 V VOCM to VO,CM performance. VOCM dynamic performance. -3 dB bandwidth Slew rate SR VOCM input characteristics. Input voltage range VIN +25°C 01 0.8 1.1 V Input resistance RIN +25°C 01 7.0 10.3 kΩ Input offset voltage VIO +25°C 01 -25 +31 mV VOS,CM = VO,CM – VOCM; VIP = VIN = VOCM = 0 V See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 6 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 3.3 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max 3.3 V VOCM to VO,CM performance – continued. VOCM input characteristics continued. Input voltage noise f = 100 kHz +25°C 01 23.5 typical nV / Hz Gain +25°C 01 ∆VICM = 0.5 V dc; +25°C RF = RG = 10 kΩ, RL = open circuit 1.02 V/V 1.01 typical -55°C to +105°C Common mode rejection ratio 0.99 01 -77 dB -76 typical -55°C to +105°C 3.3 V general performance. Power supply. Operating range Quiescent current per amplifier Enabled Enabled variation +25°C 01 +25°C 01 +PSRR ∆VICM = 0.5 V dc; +25°C RF = RG = 10 kΩ, RL = open circuit -PSRR ∆VICM = 0.5 V dc; 2.35 V mA µA/ °C mA 2.4 typical 01 -55°C to +105°C +25°C RF = RG = 10 kΩ, RL = open circuit 40 0.44 +25°C -55°C to +105°C Power supply rejection ratio 32 81 typical -55°C to +105°C Disabled 3.3 typical -55°C to +105°C -70 dB -68 typical -76 -77 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 7 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 3.3 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max 3.3 V general performance - continued. Power down ( PD ). PD input voltage Disabled +25°C 01 < 0.8 typical V >1.3 typical Enabled Turn off time +25°C 01 1 typical µs Turn on time +25°C 01 12 typical ns +25°C 01 0.09 typical µA PD pin bias current Enabled, PD = 3.3 V 97 typical Disabled, PD = 0 V Operating temperature range 01 -55 +105 °C See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 8 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 5 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Dynamic performance. -3 dB small signal bandwidth SSBW VO,dm = 0.1 VP-P +25°C 01 1350 typical MHz -3 dB large signal bandwidth LSBW VO,dm = 2 VP-P +25°C 01 937 typical MHz VO,dm = 0.1 VP-P +25°C 01 369 typical MHz Bandwidth for 0.1 dB flatness Slew rate SR VO,dm = 2 V step, 25% to 75% +25°C 01 3400 typical V/µs Settling time to 0.1% tS VO,dm = 2 V step, RL = 200 Ω +25°C 01 6 typical ns G = 3, VIN,dm = 0.7 VP-P pulse +25°C 01 1.5 typical ns -55°C to +105°C 01 -104 typical dBc Overdrive recovery time Noise / harmonic performance. Second harmonic distortion Third harmonic distortion HD2 HD3 Third order intermodulation distortion (IMD) VO,dm = 2 VP-P, fC = 10 MHz VO,dm = 2 VP-P, fC = 30 MHz -91 typical VO,dm = 2 VP-P, fC = 70 MHz -79 typical VO,dm = 2 VP-P, fC = 100 MHz -73 typical -55°C to +105°C VO,dm = 2 VP-P, fC = 10 MHz 01 -101 typical VO,dm = 2 VP-P, fC = 30 MHz -93 typical VO,dm = 2 VP-P, fC = 70 MHz -82 typical VO,dm = 2 VP-P, fC = 100 MHz -75 typical +25°C VO,dm = 1 VP-P / tone, 01 94 typical dBc dBc fC = 70.05 MHz ±0.05 MHz 90 typical VO,dm = 1 VP-P / tone, fC = 140.05 MHz ±0.05 MHz See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 9 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 5 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Noise / harmonic performance - continued. Input voltage noise f = 100 kHz +25°C 01 -55°C to +105°C Input current noise f = 100 kHz +25°C 01 1.2 typical nV / 1.3 typical Hz 2.8 typical pA / Hz DC performance. Input offset voltage VIO VIP = VIN = VOCM = 0 V, -55°C to +105°C 01 -3.1 +3.1 mV -55°C to +105°C 01 +25°C 01 -34 -15 µA -0.05 typical µA / °C RL = open circuit Input offset voltage drift ∆VIO Input bias current IIB Input bias current drift ∆IIB -55°C to +105°C 01 Input offset current IIO +25°C 01 +25°C 01 Open loop gain RF = RG = 10 kΩ, ∆VO = 1 V, 1.8 typical -0.82 64 typical µA dB 61 typical -55°C to +105°C RL = open circuit +0.82 µV / °C Input characteristics. Input common mode voltage range Input resistance RIN Differential +25°C 01 +25°C 01 Common mode 0.3 2.8 V 150 typical kΩ 3 typical MΩ See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 10 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 5 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Input characteristics – continued. Input capacitance CIN Common mode +25°C 01 Common mode rejection mode CMRR ∆VICM = 1 V dc; +25°C 01 1 typical -77 pF dB -76 typical RF = RG = 10 kΩ, RL = open circuit -55°C to +105°C Each single ended output, RF = RG = 10 kΩ -55°C to +105°C 01 Linear output current Each single ended output, f = 1 MHz, THD ≤ 60 dBc +25°C 01 30 typical mA Output balance error f = 1 MHz +25°C 01 55 typical dB VO,CM = 0.1 VP-P +25°C 01 740 typical MHz VO,CM = 2 VP-P , 25% to 75% +25°C 01 1224 typical V/µs Output characteristics. Output voltage VOUT 0.18 3.38 V 5 V VOCM to VO,CM performance. VOCM dynamic performance. -3 dB bandwidth Slew rate SR VOCM input characteristics. Input voltage range VIN +25°C 01 0.5 2.3 V Input resistance RIN +25°C 01 7.0 10.2 kΩ Input offset voltage VIO +25°C 01 -25 +15 mV VOS,CM = VO,CM – VOCM; VIP = VIN = VOCM = 0 V See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 11 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 5 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max 5 V VOCM to VO,CM performance – continued. VOCM input characteristics - continued. Input voltage noise f = 100 kHz +25°C 01 23.5 typical nV / Hz Gain +25°C 01 ∆VOCM = 1.5 V dc; +25°C RF = RG = 10 kΩ, RL = open circuit 1.02 V/V 1 typical -55°C to +105°C Common mode rejection ratio 0.99 01 -77 dB -76 typical -55°C to +105°C 5 V general performance. Power supply. Operating range Quiescent current per amplifier Enabled Enabled variation +25°C 01 +25°C 01 0.45 +25°C +PSRR ∆VICM = 1 V dc; +25°C RF = RG = 10 kΩ, RL = open circuit -PSRR ∆VICM = 1 V dc; 01 -55°C to +105°C +25°C RF = RG = 10 kΩ, RL = open circuit 38.4 2.6 V mA µA/ °C mA 2.7 typical -55°C to +105°C Power supply rejection ratio 31.1 74.5 typical -55°C to +105°C Disabled 5 typical -55°C to +105°C -71 dB -70 typical -75 -78 typical See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 12 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions 2/ VS = 5 V, unless otherwise specified Temperature, TA Device type Limits Min Unit Max 5 V general performance. Power down ( PD ). PD input voltage Disabled +25°C 01 < 2.5 typical V >3 typical Enabled Turn off time +25°C 01 1 typical µs Turn on time +25°C 01 12 typical ns +25°C 01 0.09 typical µA PD pin bias current Enabled, PD = 5 V 97 typical Disabled, PD = 0 V Operating temperature range 01 -55 +105 °C 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, VICM = 0.9 V, VOCM = 0.9 V, fixed resistance (RF) = 301 Ω, gain resistance (RG) = 301 Ω, load resistance (RL,dm) = 1 kΩ, single ended input, differential output. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 13 Case X FIGURE 1. Case outline. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 14 Case X – continued. Dimensions Inches Symbol Millimeters Min Med Max Min Med Max A 0.027 0.029 0.031 0.70 0.75 0.80 A1 0.0007 --- 0.001 0.02 --- 0.05 A2 0.007 REF 0.20 REF b 0.007 0.009 0.011 0.18 0.23 0.30 D/E 0.114 0.118 SQ 0.122 2.90 3.00 SQ 3.10 D1/E1 0.045 0.051 SQ 0.057 1.15 1.30 SQ 1.45 e 0.019 BSC 0.50 BSC L 0.011 0.015 0.019 0.30 0.40 0.50 L1 0.009 --- --- 0.25 --- --- NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. The exposed pad should be connected to a thermal ground to dissipate heat. For proper connection of the exposed pad, refer to the pin configuration and function descriptions section of the manufacturer’s datasheet. 3. Falls within reference to JEDEC MO-220-WEED. FIGURE 1. Case outline - Continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 15 Device type 01 Case outline X Terminal number Terminal symbol 1 -FB Negative output for feedback component connection 2 +IN Positive input summing node. 3 -IN Negative input summing node. 4 +FB Positive output for feedback component connection 5 +VS Positive supply voltage. 6 +VS Positive supply voltage. 7 +VS Positive supply voltage. 8 +VS Positive supply voltage. 9 VOCM Output common mode voltage. 10 +OUT Positive output for load connection. 11 -OUT Negative output for load connection. 12 PD Power down pin. 13 -VS Negative supply voltage. 14 -VS Negative supply voltage. 15 -VS Negative supply voltage. 16 -VS Negative supply voltage. EPAD Description Exposed pad. The exposed pad is not electrically connected to the device. It is typically soldered to ground or a power plane on the printed circuit board (PCB) that is thermally conductive. FIGURE 2. Terminal connections. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 16 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Transportation mode and order quantity Vendor part number 2/ V62/13615-01XE 24355 Reel, 250 ADA4930-1SCPZ-EPR2 Reel, 1,500 ADA4930-1SCPZ-EPR7 Reel, 5,000 ADA4930-1SCPZ-EPRL 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ Due to size limitation, the vendor will mark the part with “H2X” in lieu of the vendor part number. CAGE code 24355 DLA LAND AND MARITIME COLUMBUS, OHIO Source of supply Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/13615 PAGE 17