REVISIONS LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 PMIC N/A PREPARED BY RICK OFFICER Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA 12-11-29 4 A REV 5 6 7 8 9 10 11 12 13 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil/ TITLE MICROCIRCUIT, LINEAR, LOW POWER, 350 MHz VOLTAGE FEEDBACK AMPLIFIER, MONOLITHIC SILICON APPROVED BY CHARLES F. SAFFLE SIZE AMSC N/A 3 CODE IDENT. NO. DWG NO. V62/12644 16236 PAGE 1 OF 13 5962-V099-12 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low power, 350 MHz voltage feedback amplifier microcircuit, with an operating temperature range of -55°C to +105°C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/12644 - Drawing number 01 X E Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). Device type Generic 01 AD8039 Circuit function Low power, 350 MHz voltage feedback amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins X 8 JEDEC PUB 95 Package style MS-012-AA Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z DLA LAND AND MARITIME COLUMBUS, OHIO Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 2 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) .................................................................................................... 12.6 V Power dissipation (PD) ............................................................................................... 360 mW 2/ Common mode input voltage (VIN) ............................................................................ Differential input voltage ............................................................................................. Storage temperature range (TSTG) ............................................................................ Lead temperature (soldering, 10 seconds) ................................................................. Junction temperature range (TJ) ................................................................................ ±VS ±4 V -65°C to +125°C +300°C 150°C 1.4 Recommended operating conditions. 3/ Supply voltage range (VS) .......................................................................................... ±5 V Operating free-air temperature range (TA) ................................................................. -55°C to +105°C 1.5 Thermal characteristics. Thermal resistance, junction to ambient (θJA) ............................................................ 125°C/W 1/ 2/ 3/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Power dissipation arrived by PD = (TJ – TA) / θJA. PD = (150 – 105) / 125 = 0.36 W Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 3 2. APPLICABLE DOCUMENTS JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http://www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VS = ±5 V, RL = 2 kΩ, gain = +1 unless otherwise specified Temperature, TA Device type Limits Min Unit Max Dynamic performance. -3 dB bandwidth Bandwidth for 0.1 dB flatness Slew rate SR 01 300 MHz G = +1, VOUT = 0.5 Vpp -55°C to +105°C G = +2, VOUT = 0.5 Vpp +25°C 175 typical G = +1, VOUT = 2 Vpp +25°C 100 typical G = +2, VOUT = 0.2 Vpp +25°C 01 G = +1, VOUT = 2 V step, RL = 2 kΩ +25°C 01 45 typical MHz 400 V/µs 300 -55°C to +105°C Overdrive recovery time G = +2, 1 V overdrive +25°C 01 50 typical ns Settling time to 0.1% G = +2, VOUT = 2 V step +25°C 01 18 typical ns +25°C 01 -90 typical dBc +25°C 01 -92 typical dBc +25°C 01 -65 typical dBc +25°C 01 -70 typical dBc f = 5 MHz, G = +2 +25°C 01 -70 typical dB f = 100 kHz +25°C 01 8 typical nV/ Noise/harmonic performance. Signal frequency distortion response (SFDR) Second harmonic fc = 1 MHz, VOUT = 2 Vpp, RL = 2 kΩ Third harmonic fc = 1 MHz, VOUT = 2 Vpp, RL = 2 kΩ Second harmonic fc = 5 MHz, VOUT = 2 Vpp, RL = 2 kΩ Third harmonic fc = 5 MHz, VOUT = 2 Vpp, RL = 2 kΩ Crosstalk, output to output CT Input voltage noise Hz Input current noise f = 100 kHz +25°C 01 600 typical fA/ Hz See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 5 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions VS = ±5 V, RL = 2 kΩ, gain = +1 unless otherwise specified Temperature, TA Device type Limits Min Unit Max DC performance. Input offset voltage +25°C VIO 01 3 mV 4.5 -55°C to +105°C Input offset voltage drift ∆VIO +25°C 01 Input bias current IIB +25°C 01 4.5 typical -55°C to +105°C µV/°C 750 nA 2.0 µA Input bias current drift ∆IIB +25°C 01 3 typical nA/°C Input offset current IIO +25°C 01 ±25 typical nA Open loop gain AOL +25°C 01 70 typical dB VOUT = ±2.5 V Input characteristics. Input resistance RIN +25°C 01 10 typical MΩ Input capacitance CIN +25°C 01 2 typical pF Input common mode voltage range VINR RL = 1 kΩ +25°C 01 ±4 typical V Common mode rejection ratio CMRR VCM = ±2.5 V +25°C 01 61 dB 59 -55°C to +105°C Output characteristics. DC output voltage swing Capacitive load drive CL RL = 2 kΩ, saturated output +25°C 01 ±4 typical V 30% overshoot, G = +2 +25°C 01 20 typical pF See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 6 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions VS = ±5 V, RL = 2 kΩ, gain = +1 unless otherwise specified Temperature, TA Device type Limits Unit Min Max 3 12 V 1.5 mA Power supply . Operating range +25°C 01 Quiescent current per amplifier +25°C 01 2.6 -55°C to +105°C Power supply rejection ratio Positive supply +25°C Negative supply 01 71 -55°C to +105°C 63 +25°C 64 -55°C to +105°C 63 dB See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 7 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions VS = 5 V, RL = 2 kΩ to VS/2, gain = +1, unless otherwise specified Temperature, TA Device type Limits Min Unit Max Dynamic performance. -3 dB bandwidth Bandwidth for 0.1 dB flatness Slew rate SR 01 275 MHz G = +1, VOUT = 0.2 Vpp -55°C to +105°C G = +2, VOUT = 0.2 Vpp +25°C 150 typical G = +1, VOUT = 2 Vpp +25°C 30 typical G = +2, VOUT = 0.2 Vpp +25°C 01 G = +1, VOUT = 2 V step, RL = 2 kΩ +25°C 01 45 typical MHz 340 V/µs 275 -55°C to +105°C Overdrive recovery time G = +2, 1 V overdrive +25°C 01 50 typical ns Settling time to 0.1% G = +2, VOUT = 2 V step +25°C 01 18 typical ns +25°C 01 -82 typical dBc +25°C 01 -79 typical dBc +25°C 01 -60 typical dBc +25°C 01 -67 typical dBc f = 5 MHz, G = +2 +25°C 01 -70 typical dB f = 100 kHz +25°C 01 8 typical nV/ Noise/harmonic performance. Signal frequency distortion response (SFDR) Second harmonic fc = 1 MHz, VOUT = 2 Vpp, RL = 2 kΩ Third harmonic fc = 1 MHz, VOUT = 2 Vpp, RL = 2 kΩ Second harmonic fc = 5 MHz, VOUT = 2 Vpp, RL = 2 kΩ Third harmonic fc = 5 MHz, VOUT = 2 Vpp, RL = 2 kΩ Crosstalk, output to output CT Input voltage noise Hz Input current noise f = 100 kHz +25°C 01 600 typical fA/ Hz See footnotes at end of table. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 8 TABLE I. Electrical performance characteristics – Continued. 1/ Test Symbol Conditions VS = 5 V, RL = 2 kΩ to VS/2, gain = +1, unless otherwise specified Temperature, TA Device type Limits Min Unit Max DC performance. Input offset voltage +25°C VIO 01 3 mV 4.5 -55°C to +105°C Input offset voltage drift ∆VIO +25°C 01 Input bias current IIB +25°C 01 3 typical -55°C to +105°C µV/°C 750 nA 2.0 µA Input bias current drift ∆IIB +25°C 01 3 typical nA/°C Input offset current IIO +25°C 01 ±30 typical nA Open loop gain AOL +25°C 01 70 typical dB VOUT = ±2.5 V Input characteristics. Input resistance RIN +25°C 01 10 typical MΩ Input capacitance CIN +25°C 01 2 typical pF Input common mode voltage range VINR RL = 1 kΩ +25°C 01 1.0 to 4.0 typical V Common mode rejection ratio CMRR VCM = ±1 V +25°C 01 59 dB 59 -55°C to +105°C Output characteristics. DC output voltage swing RL = 2 kΩ, saturated output +25°C 01 0.9 to 4.1 typical V 30% overshoot, G = +2 +25°C 01 20 typical pF Operating range +25°C 01 Quiescent current per amplifier +25°C 01 -55°C to +105°C 01 Capacitive load drive CL Power supply . Power supply rejection ratio 1/ 3 12 V 1.5 mA 65 dB Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 9 Case X FIGURE 1. Case outline. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 10 Case X Dimensions Inches Symbol Millimeters Min Max Min Max A .053 .068 1.35 1.75 A1 .004 .010 0.10 0.25 b .012 .020 0.31 0.51 c .006 .009 0.17 0.25 D .188 .196 4.80 5.00 E .149 .157 3.80 4.00 E1 .228 .244 5.80 6.20 e .050 BSC L .015 1.27 BSC .049 0.40 1.27 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within reference to JEDEC MS-012-AA. FIGURE 1. Case outline - Continued. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 11 Device type 01 Case outline X Terminal number Terminal symbol 1 VOUT1 2 -INPUT1 3 +INPUT1 4 -VS 5 +INPUT2 6 -INPUT2 7 VOUT2 8 +VS FIGURE 2. Terminal connections. DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 12 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number V62/12644-01XE 24355 AD8039SARZ-EPR7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code 24355 DLA LAND AND MARITIME COLUMBUS, OHIO Source of supply Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland SIZE A CODE IDENT NO. 16236 REV DWG NO. V62/12644 PAGE 13