AD8672-DSCC: Military Data Sheet

REVISIONS
LTR
DESCRIPTION
DATE
Prepared in accordance with ASME Y14.24
APPROVED
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
PAGE
1
2
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
15-11-04
4
A
REV
5
6
7
8
9
10
11
12
13
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
MICROCIRCUIT, LINEAR, PRECISION, VERY
LOW NOISE, LOW INPUT BIAS CURRENT DUAL,
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
APPROVED BY
CHARLES F. SAFFLE
SIZE
AMSC N/A
3
CODE IDENT. NO.
DWG NO.
V62/16603
16236
PAGE
1
OF
13
5962-V003-16
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a precision, very low noise, low input bias current dual operational
amplifier microcircuit, with an operating temperature range of -55C to +125C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/16603
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
AD8672-EP
Circuit function
Precision, very low noise, low input bias current
dual operational amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
8
JEDEC PUB 95
Package style
MS-012-AA
Plastic small outline surface mount
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer:
Finish designator
A
B
C
D
E
Z
1.3 Absolute maximum ratings.
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
1/
Supply voltage (VS) .................................................................................................................. 36 V
Input voltage (VIN) .................................................................................................................... -VS to +VS
Differential input voltage (VID) .................................................................................................. 0.7 V
Output short circuit duration ..................................................................................................... Indefinite
Power dissipation (PD) ............................................................................................................. 0.210 W
Storage temperature range (TSTG) .......................................................................................... -65C to +150C
Junction temperature range (TJ) .............................................................................................. -65C to +150C
Lead temperature range (soldering, 60 seconds) ..................................................................... +300C
Thermal resistance, junction to ambient (JC) .......................................................................... 43C/W
Thermal resistance, junction to ambient (JA) .......................................................................... 120C/W
_______
1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
2
1.4 Recommended operating conditions. 2/
Supply voltage range (VS) ........................................................................................................ 5 V and 15 V
Operating free-air temperature range (TA) ............................................................................... -55C to +125C
2. APPLICABLE DOCUMENTS
JEDEC Solid State Technology Association
JEDEC PUB 95
–
Registered and Standard Outlines for Semiconductor Devices
(Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107).
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
2/
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
3
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions
VS = 5.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics
Offset voltage
+25C
VOS
01
75
V
20 typical
125
-55C to +125C
30 typical
Offset voltage drift
Input bias current
VOS /
T
-55C to +125C
01
0.8
0.3 typical
+25C
IB
01
-14
+14
V /
C
nA
+3 typical
-20
+25C to +125C
+20
+5 typical
-60
-55C to +125C
+60
+8 typical
Input offset current
+25C
IOS
01
-14
+14
nA
+6 typical
-20
+25C to +125C
+20
+6 typical
-60
-55C to +125C
+60
+8 typical
Input voltage range
VINR
Common mode
rejection ratio
CMRR
VCM = -2.5 V to +2.5 V
+25C
01
-2.5
+25C
01
100
+2.5
V
dB
120 typical
Large signal voltage
gain
AVO
+25C
RL = 2 k, VO = -3 V to +3 V
01
1000
V/
mV
6000 typical
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
4
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 5.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input capacitance,
common mode
CINCM
+25C
01
6.25 typical
pF
Input capacitance,
differential mode
CINDM
+25C
01
7.5 typical
pF
Input resistance,
common mode
RIN
+25C
01
3.5 typical
G
Input resistance,
differential mode
RINDM
+25C
01
15 typical
M
+25C
01
Output characteristics.
High output voltage
VOH
RL = 600 
+3.7
V
+3.9 typical
+3.8
-55C to +125C
RL = 2 k
+4.0 typical
Low output voltage
VOL
RL = 600 
+25C
01
-3.7
V
-3.8 typical
-3.8
-55C to +125C
RL = 2 k
-3.9 typical
Output current
IOUT
+25C
01
+25C
01
10 typical
mA
Power supply
Power supply
rejection ratio
PSRR
VS = 4 V to 18 V
110
dB
130 typical
Supply current per
amplifier
ISY
+25C
VO = 0 V
01
3.5
mA
3 typical
-55C to +125C
4.2
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 5.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Dynamic performance
Slew rate
SR
RL = 2 k
+25C
01
4 typical
V/s
Settling time
tS
To 0.1%, 4 V step, G = 1
+25C
01
1.4 typical
s
To 0.01%, 4 V step, G = 1
Gain bandwidth
product
5.1 typical
GBP
+25C
01
+25C
01
10 typical
MHz
Noise performance
Peak to peak noise
en p-p
0.1 Hz to 10 Hz
100
nV p-p
77 typical
Voltage noise density
en
f = 1 kHz
+25C
01
3.8
nV /
Hz
2.8 typical
Current noise density
in
f = 1 kHz
+25C
01
0.3 typical
pA /
Hz
Channel separation
CS
f = 1 kHz
+25C
01
f = 10 kHz
-130 typical
dB
-105 typical
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics
Offset voltage
+25C
VOS
01
V
75
20 typical
125
-55C to +125C
30 typical
Offset voltage drift
Input bias current
VOS /
T
-55C to +125C
01
0.8
0.3 typical
+25C
IB
01
-14
V /
C
+14
nA
+3 typical
-20
+25C to +125C
+20
+5 typical
-60
-55C to +125C
+60
+8 typical
Input offset current
+25C
IOS
01
-14
+14
nA
+6 typical
-20
+25C to +125C
+20
+6 typical
-60
-55C to +125C
+60
+8 typical
Input voltage range
VINR
Common mode
rejection ratio
CMRR
VCM = -12 V to +12 V
+25C
01
-12
+25C
01
100
+12
V
dB
120 typical
Large signal voltage
gain
AVO
+25C
RL = 2 k, VO = -10 V to +10 V
01
1000
V/
mV
6000 typical
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
7
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input capacitance,
common mode
CINCM
+25C
01
6.25 typical
pF
Input capacitance,
differential mode
CINDM
+25C
01
7.5 typical
pF
Input resistance,
common mode
RIN
+25C
01
3.5 typical
G
Input resistance,
differential mode
RINDM
+25C
01
15 typical
M
+25C
01
Output characteristics.
High output voltage
VOH
RL = 600 
+11
V
+12.3 typical
+13.2
-55C to +125C
RL = 2 k
+13.8 typical
Low output voltage
VOL
RL = 600 
+25C
01
-13.2
V
-13.8 typical
-11
-55C to +125C
RL = 2 k
-12.4 typical
Output current
IOUT
+25C
01
20 typical
mA
Short circuit current
ISC
+25C
01
30 typical
mA
+25C
01
Power supply
Power supply
rejection ratio
PSRR
VS = 4 V to 18 V
110
dB
130 typical
Supply current per
amplifier
ISY
+25C
VO = 0 V
01
3.5
mA
3 typical
-55C to +125C
4.2
See footnote at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
8
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 15.0 V, VCM = 0 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Dynamic performance
Slew rate
SR
RL = 2 k
+25C
01
4 typical
V/s
Settling time
tS
To 0.1%, 10 V step, G = 1
+25C
01
2.2 typical
s
To 0.01%, 10 V step, G = 1
Gain bandwidth
product
6.3 typical
GBP
+25C
01
+25C
01
10 typical
MHz
Noise performance
Peak to peak noise
en p-p
0.1 Hz to 10 Hz
100
nV p-p
77 typical
Voltage noise density
en
f = 1 kHz
+25C
01
3.8
nV /
Hz
2.8 typical
Current noise density
in
f = 1 kHz
+25C
01
0.3 typical
pA /
Hz
Channel separation
CS
f = 1 kHz
+25C
01
f = 10 kHz
1/
-130 typical
dB
-105 typical
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
9
Case X
FIGURE 1. Case outline.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
10
Case X – continued.
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
.0532
.0688
1.35
1.75
A1
.0040
.0098
0.10
0.25
b
.0122
.0201
0.31
0.51
c
.0067
.0098
0.17
0.25
D
.1890
.1968
4.80
5.00
e
.0500
BSC
1.27
BSC
E
.1497
.1574
3.80
4.00
E1
.2284
.2441
5.80
6.20
L
.0157
.0500
0.40
1.27
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. Inch dimensions are rounded off millimeter equivalents for reference only and are not appropriate use in design.
3. Falls within reference to JEDEC MS-012-AA.
FIGURE 1. Case outline - Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
11
Device type
01
Case outline
X
Terminal number
Terminal
symbol
1
OUTPUT A
2
-INPUT A
3
+INPUT A
4
-VS
5
+INPUT B
6
-INPUT B
7
OUTPUT B
8
+VS
FIGURE 2. Terminal connections.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
12
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Mode of
transportation
and quantity
Vendor part number
V62/16603-01XE
24355
Tube, 98 units
AD8672TRZ-EP
V62/16603-01XE
24355
Reel, 1,000 units
AD8672TRZ-EP-R7
1/ The vendor item drawing establishes an administrative control number for identifying the
item on the engineering documentation.
CAGE code
24355
DLA LAND AND MARITIME
COLUMBUS, OHIO
Source of supply
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: Raheen Business Park
Limerick, Ireland
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/16603
PAGE
13