Data Sheet Radar Receive Path AFE: 4-Channel LNA and PGA ADA8282 FEATURES FUNCTIONAL BLOCK DIAGRAM APPLICATIONS ADA8282 +INA +OUTA 3nV√Hz LNA PGA –INA –OUTA +24dB –6dB TO +12dB +INB +OUTB 3nV√Hz LNA PGA –INB –OUTB +24dB –6dB TO +12dB +INC +OUTC 3nV√Hz LNA PGA –INC –OUTC +24dB –6dB TO +12dB +IND +OUTD 3nV√Hz LNA PGA –IND –OUTD +24dB POWER MODE –6dB TO +12dB GAIN SELECT SPI CS SCLK SDI SDO VIO AVDD RESET 13132-001 4 channels of low noise amplifiers (LNAs) followed by programmable gain amplifiers (PGAs) Minimum −3 dB bandwidth of 5 MHz Typical –3 dB bandwidth of 42.3 MHz Typical slew rate of 28 V/µs Differential input and output Gain of 18 dB to 36 dB in 6 dB steps Selectable low noise and low power modes Input referred noise of 4.5 nV/√Hz at 18.3 mW per channel Input referred noise of 3.8 nV/√Hz at 26.5 mW per channel Input referred noise of 3.6 nV/√Hz at 34.8 mW per channel Input referred noise of 3.4 nV/√Hz at 54.8 mW per channel Channel to channel gain matching of ±0.25 dB Absolute gain error of ±0.5 dB SPI programmable Power-down mode (SPI selectable) 3.1 V p-p differential output swing when using a 3.3 V supply 32-lead, 5 mm × 5 mm LFCSP package Specified from −40°C to +125°C Qualified for automotive applications Figure 1. Automotive radar Adaptive cruise control Collision avoidance Blind spot detection Self parking Electronic bumpers GENERAL DESCRIPTION The ADA8282 is designed for applications that require low cost, low power, compact size, and flexibility. The ADA8282 has four parallel channels, each including an LNA and a PGA. The LNA and PGA combine to form a signal chain that features a gain range of 18 dB to 36 dB in 6 dB increments with a guaranteed minimum bandwidth of 5 MHz. Using the highest power settings, the combined input referred voltage noise of the combined LNA and PGA channel is 3.4 nV/√Hz at maximum gain. Rev. 0 The ADA8282 can be configured in four power modes that trade off power and noise performance to optimize the overall performance according to the end application. Fabricated in an advanced complementary metal-oxide semiconductor (CMOS) process, the ADA8282 is available in a 5 mm × 5 mm, RoHS-compliant, 32-lead LFCSP. It is specified over the automotive temperature range of −40°C to +125°C. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility isassumed by Analog Devicesfor its use,norfor any infringements of patents or other rights of third parties thatmay resultfrom its use.Specificationssubject to changewithoutnotice.No license is granted by implication or otherwise under any patent or patent rights of Analog Devices . Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADA8282 Data Sheet TABLE OF CONTENTS Features........................................................................................... 1 Output Swing Variation with Gain......................................... 12 Applications ................................................................................... 1 Offset Voltage Adjustments .................................................... 12 Functional Block Diagram............................................................ 1 Single-Ended or Differential Input......................................... 12 General Description ...................................................................... 1 Short-Circuit Currents............................................................ 12 Revision History ............................................................................ 2 SPI Interface ............................................................................. 12 Specifications ................................................................................. 3 Channel to Channel Phase Matching..................................... 13 Digital Specifications................................................................. 4 Applications ................................................................................. 14 Absolute Maximum Ratings ......................................................... 5 Increased Gain Using Two ADA8282 Devices in Series....... 14 Thermal Resistance ................................................................... 5 Multiplexing Inputs Using Multiple ADA8282 Devices....... 15 ESD Caution............................................................................... 5 Basic Connections for a Typical Application......................... 16 Pin Configuration and Function Descriptions............................ 6 Register Map ................................................................................ 17 Typical Performance Characteristics............................................ 7 Register Summary ................................................................... 17 Theory of Operation.................................................................... 11 Register Details ........................................................................ 17 Radar Receive Path AFE.......................................................... 11 Outline Dimensions .................................................................... 21 Default SPI Settings................................................................. 11 Ordering Guide............................................................................ 21 Input Impedance...................................................................... 11 Automotive Products............................................................... 21 Power Modes............................................................................ 11 Programmable Gain Range ..................................................... 12 REVISION HISTORY 7/15—Revision 0: Initial Version Rev. 0 | Page 2 of 21 Data Sheet ADA8282 SPECIFICATIONS AVDD = 3.3 V, LNA + PGA gain = 36 dB (LNA gain = 24 dB, PGA gain = 12 dB), TA = −40°C to +125°C, PGA_BIAS_SEL = b’10, LNA_BIAS_SEL= b’10, unless otherwise noted. Table 1. Parameter ANALOG CHANNEL CHARACTERISTICS Gain Gain Range Gain Error −3 dB Bandwidth Channel to Channel Gain Matching Channel to Channel Phase Matching1 Slew Rate Input Referred Noise Output Referred Noise Offset Voltage Referred to Input Referred to Output SPI Offset Adjustment Resolution (Relative to Input) SPI Offset Adjustment Range (Relative to Input) Harmonic Distortion Second Harmonic (HD2) Third Harmonic (HD3) Intermodulation Distortion Test Conditions/Comments Min Typ Max Unit ±0.5 dB dB dB 18/24/30/36 18 VOUT = 100 mV p-p, gain = 36 dB PGA_BIAS_SEL = b’00, LNA_BIAS_SEL = b’00 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’01 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’10 PGA_BIAS_SEL = b’11, LNA_BIAS_SEL = b’11 Frequencies up to 5 MHz Frequencies up to 5 MHz Gain = 36 dB at 2 MHz PGA_BIAS_SEL = b’00, LNA_BIAS_SEL = b’00 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’01 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’10 PGA_BIAS_SEL = b’11, LNA_BIAS_SEL = b’11 50 Ω impedance used for voltage to power conversion Gain = 18 dB Gain = 24 dB Gain = 30 dB Gain = 36 dB 5 5 5 5 20.5 34.2 42.3 52.3 0.1 0.1 28 ±0.25 ±1 MHz MHz MHz MHz dB Degrees V/μs 4.5 3.8 3.6 3.4 −156 nV/√Hz nV/√Hz nV/√Hz nV/√Hz dBm/Hz 36 61 115 218 nV/√Hz nV/√Hz nV/√Hz nV/√Hz Gain = 36 dB Gain = 36 dB LNA_BIAS_SEL = b’00 ±0.8 ±50 113 LNA_BIAS_SEL = b’01 LNA_BIAS_SEL = b’10 LNA_BIAS_SEL = b’11 LNA_BIAS_SEL = b’00 186 250 440 ±4 μV μV μV mV LNA_BIAS_SEL = b’01 LNA_BIAS_SEL = b’10 LNA_BIAS_SEL = b’11 ±6 ±8 ±14 mV mV mV VOUT = 2 V p-p, fIN = 100 kHz VOUT = 100 mV p-p, fIN = 2 MHz VOUT = 2 V p-p, fIN = 100 kHz VOUT = 100 mV p-p, fIN = 2 MHz VOUT = 2 V p-p, fIN1 = 100 kHz, fIN2 = 150 kHz VOUT = 100 mV p-p, fIN1 = 2 MHz, fIN2 = 2.1 MHz −70 −85 −85 −95 −72 −83 −80 −105 dBc dBc dBc dBc dBc dBc dB dBc Common-Mode Rejection Ratio (CMRR) Crosstalk Rev. 0 | Page 3 of 21 ±3 ±200 mV mV μV ADA8282 Parameter POWER SUPPLY Total Power Dissipation Data Sheet Test Conditions/Comments Min Typ PGA_BIAS_SEL = b’00, LNA_BIAS_SEL = b’00 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’01 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’10 PGA_BIAS_SEL = b’11, LNA_BIAS_SEL = b’11 Power Dissipation per Channel AVDD VIO IAVDD IVIO Power-Down Current Power-Down Dissipation Power-Up Time Power Supply Rejection Ratio (PSRR) INPUT Input Resistance Differential Input Resistance Common-Mode Input Resistance Differential Input Capacitance OUTPUT Output Voltage Swing Output Balance Short-Circuit Current Capacitive Load 1 Max Unit 73 106 139 219 mW mW mW mW mW V V 31 3.0 1.8 3.6 3.6 Four channels active PGA_BIAS_SEL = b’00, LNA_BIAS_SEL = b’00 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’01 PGA_BIAS_SEL = b’01, LNA_BIAS_SEL = b’10 PGA_BIAS_SEL = b’11, LNA_BIAS_SEL = b’11 One channel active 19.6 29 37.7 60 9.8 10 20 0.07 5 IAVDD and IVIO Time to operational after chip is enabled At dc At 1 MHz mA mA mA mA mA μA μA mW μs dB dB 1.7 0.42 13.2 kΩ kΩ pF −80 −80 1.45 0.37 10.8 +OUTx (−OUTx), gain = 18 dB +OUTx (−OUTx), gain = 24 dB, 30 dB, or 36 dB fIN = 100 kHz Per output at 25°C 20% overshoot 22 32 42 66.3 11 12 100 0.33 1.57 0.39 12 3.1 6.3 V p-p V p-p dB mA pF −70 205 30 Normalized to 0° phase matching at 25°C; see the Theory of Operation section for details. DIGITAL SPECIFICATIONS AVDD = 3.3 V, TA = −40°C to +125°C, unless otherwise noted. Table 2. Parameter LOGIC INPUT (CS) Logic 1 Voltage Logic 0 Voltage Input Resistance Input Capacitance LOGIC INPUTS (SDI, SCLK, RESET) Logic 1 Voltage Logic 0 Voltage Input Resistance Input Capacitance Maximum SCLK Frequency LOGIC OUTPUT (SDO) Logic 1 Voltage (IOH = 800 μA) Logic 0 Voltage (IOL = 50 μA) Temperature Min Full Full 25°C 25°C 1.2 Full Full 25°C 25°C 1.2 0 Typ Max Unit VIO + 0.3 0.3 V V kΩ pF VIO + 0.3 0.3 10 V V kΩ pF MHz 0.3 V V 15 0.5 2.5 2 Full Full VIO − 0.3 Rev. 0 | Page 4 of 21 Data Sheet ADA8282 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 3. Parameter Electrical AVDD to EPAD +INx, −INx, SCLK, SDI, SDO, CS, VIO, RESET, −OUTx, +OUTx to EPAD ESD Ratings Human Body Model (HBM) Charged Device Model (CDM) Environmental Operating Temperature Range (Ambient) Storage Temperature Range (Ambient) Maximum Junction Temperature Lead Temperature (Soldering, 10 sec) θJA is specified for the worst case conditions, that is, a device soldered in a circuit board for surface-mount packages. Rating −0.3 V to +3.9 V −0.3V to AVDD + 0.3 V ±4000 V ±2000 V Table 4. Thermal Resistance Package Type 32-Lead, 5 mm × 5 mm LFCSP ESD CAUTION −40°C to +125°C −65°C to +150°C 150°C 300°C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. 0 | Page 5 of 21 θJA 33.51 θJC 4.1 Unit °C/W ADA8282 Data Sheet 32 31 30 29 28 27 26 25 AVDD SDO SDI CS SCLK RESET VIO AVDD PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 ADA8282 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD NOTES 1. NIC = NO INTERNAL CONNECTION. 2. TIE THE EXPOSED PAD ON THE BOTTOM SIDE OF THE PACKAGE TO THE ANALOG/DIGITAL GROUND PLANE. 13132-002 AVDD NIC NIC NIC NIC NIC NIC AVDD 9 10 11 12 13 14 15 16 +INA –INA +INB –INB +INC –INC +IND –IND Figure 2. Pin Configuration Table 5. Pin Function Descriptions Pin No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Mnemonic EPAD +INA −INA +INB −INB +INC −INC +IND −IND AVDD NIC NIC NIC NIC NIC NIC AVDD −OUTD +OUTD −OUTC +OUTC −OUTB +OUTB −OUTA +OUTA AVDD VIO RESET 28 29 30 31 32 SCLK CS SDI SDO AVDD Description Exposed Pad. Tie the exposed pad on the bottom side of the package to the analog/digital ground plane. Positive LNA Analog Input for Channel A. Negative LNA Analog Input for Channel A. Positive LNA Analog Input for Channel B. Negative LNA Analog Input for Channel B. Positive LNA Analog Input for Channel C. Negative LNA Analog Input for Channel C. Positive LNA Analog Input for Channel D. Negative LNA Analog Input for Channel D. 3.3 V Analog Supply. No Internal Connection. Leave this pin floating. No Internal Connection. Leave this pin floating. No Internal Connection. Leave this pin floating. No Internal Connection. Leave this pin floating. No Internal Connection. Leave this pin floating. No Internal Connection. Leave this pin floating. 3.3 V Analog Supply. Negative Analog Output for Channel D. Positive Analog Output for Channel D. Negative Analog Output for Channel C. Positive Analog Output for Channel C. Negative Analog Output for Channel B. Positive Analog Output for Channel B. Negative Analog Output for Channel A. Positive Analog Output for Channel A. 3.3 V Analog Supply. Digital Level Select for SPI and RESET. This pin can accept 1.8 V to 3.3 V. Reset Input. RESET overrides the SPI and powers down the device and returns all settings back to default. RESET is pulled to ground by default. A logic high triggers the reset. Serial Clock. Chip Select Bar. Serial Data Input. Serial Data Output. 3.3 V Analog Supply. Rev. 0 | Page 6 of 21 Data Sheet ADA8282 TYPICAL PERFORMANCE CHARACTERISTICS AVDD = 3.3 V, LNA + PGA gain = 36 dB (LNA gain = 24 dB, PGA gain = 12 dB), TA = 25°C, PGA_BIAS_SEL = b’10, LNA_BIAS_SEL= b’10, unless otherwise noted. 350 25000 TA = +125°C TA = +25°C TA = –40°C TA = +125°C TA = –40°C 300 20000 NUMBER OF HITS NUMBER OF HITS 250 15000 10000 200 150 100 5000 0 2500 N: 12353 M: –7.49789 SD: 20.0841 –20 2000 N: 11292 M: 0.0246995 SD: 21.4755 –40 1500 1000 –80 500 –100 –50 0 50 100 150 VOS (mV) Figure 4. Output Offset Voltage Distribution 3000 13132-107 0.30 0.35 0.25 0.15 0.20 0.10 30dB –120 13132-110 –100 0.05 24dB 18dB 36dB 0 –150 0 –0.10 –60 0 1 2 3 4 5 FREQUENCY (MHz) 13132-108 THD (dB) NUMBER OF HITS –0.05 Figure 6. Distribution of Channel to Channel Phase Matching N: 12199 M: –13.1269 SD: 19.535 TA = +125°C TA = +25°C TA = –40°C –0.15 PHASE MISMATCH (Degrees) Figure 3. Gain Accuracy Distribution 3000 –0.20 13132-103 –0.20 –0.19 –0.18 –0.17 –0.16 –0.15 –0.14 –0.13 –0.12 –0.11 –0.10 –0.09 –0.08 –0.07 –0.06 –0.05 –0.04 –0.03 –0.02 –0.01 0 GAIN ERROR (dB) –0.30 0 0 –0.25 50 Figure 7. Total Harmonic Distortion (THD) vs. Frequency for Various Gains, VOUT = −10 dBm 1800 TA = +125°C TA = +25°C TA = –40°C 1600 2500 INPUT IMPEDANCE (Ω) 2000 1500 1000 1200 1000 800 600 400 500 DC GAIN MISMATCH (dB) 0 1k 13132-106 0.050 0.045 0.040 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 10k 100k 1M 10M 100M FREQUENCY (Hz) Figure 8. Input Impedance vs. Frequency Figure 5. Distribution of Channel to Channel Gain Matching Rev. 0 | Page 7 of 21 1G 13132-109 200 0 NUMBER OF HITS 1400 ADA8282 Data Sheet 42 GAIN = 36dB 36 30 ANALOG OUTPUT (1V/DIV) 2V 24 ANALOG OUTPUT 18 GAIN (dB) 250mV GAIN = 30dB GAIN = 24dB GAIN = 18dB 12 6 0 SDI –6 b'11 –12 TIME (80ns/DIV) –24 100k 100M 10M 1M 13132-113 –18 13132-105 b'00 FREQUENCY (Hz) Figure 12. Frequency Response at All Gains (Bias Mode 0) Figure 9. Gain Step Transient Response 30 42 GAIN = 18dB GAIN = 24dB GAIN = 30dB GAIN = 36dB 25 GAIN = 36dB 36 30 18 GAIN (dB) NOISE (nV/√Hz) 24 20 15 GAIN = 30dB GAIN = 24dB GAIN = 18dB 12 6 0 10 –6 –12 5 100k 10M 1M 100M FREQUENCY (Hz) –24 100k 13132-111 10k 1M 10M 13132-114 –18 0 1k 100M FREQUENCY (Hz) Figure 10. Input Referred Noise vs. Frequency Figure 13. Frequency Response at All Gains (Bias Mode 2) 40 4 35 3 30 2 AMPLITUDE (V) 25 50Ω 20 15 VOUT 1 0 –1 10 –2 5 –3 0 1k 10k 100k 1M 10M FREQUENCY (Hz) 100M –4 0 100 200 300 400 500 600 TIME (ns) Figure 11. Noise Figure vs. Frequency Figure 14. Overdrive Recovery Rev. 0 | Page 8 of 21 700 800 13132-115 UNTERMINATED 13132-112 NOISE FIGURE (dB) VIN × GAIN Data Sheet ADA8282 200 GAIN = 36dB 29 28 SLEW RATE (V/µs) 150 VOUT (mV) 30 NO LOAD 5pF 33pF 66pF 100pF 100 50 0 GAIN = 30dB 27 GAIN = 24dB 26 25 GAIN = 18dB 24 23 22 200 400 600 800 1000 TIME (ns) 20 –40 MODE 0 MODE 1 MODE 2 MODE 3 VOUT (V) 0 –0.5 200 300 400 500 600 700 800 900 1000 TIME (ns) 13132-121 –1.0 100 65 80 95 110 125 3.4 3.0 2.6 2.2 1.8 1.4 1.0 0.6 0.2 –0.2 –0.6 –1.0 –1.4 –1.8 –2.2 –2.6 –3.0 –3.4 18 24 30 36 Figure 19. Maximum and Minimum Differential VOUT vs. Gain 4 500 480 3 OUTPUT VOLTAGE SWING (V) 460 440 420 400 380 360 340 2 1 0 –1 TA = +85°C TA = +25°C TA = –40°C –2 –3 320 –25 10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) Figure 17. Short-Circuit Current vs. Temperature Per Channel –4 10 13132-118 SHORT-CIRCUIT CURRENT (mA) 50 35 GAIN (dB) Figure 16. Large Signal Pulse Response for Various LNA and PGA Bias Modes 300 –40 20 100 1k 10k OUTPUT LOAD RESISTANCE (Ω) 100k 13132-117 VOUT (V) 0.5 0 5 Figure 18. Output Slew Rate vs. Temperature 1.5 –1.5 10 TEMPERATURE (°C) Figure 15. Pulse Response at Various Output Capacitive Loads 1.0 –25 13132-125 0 13132-116 –50 13132-119 21 Figure 20. Differential Output Voltage Swing vs. Output Load Resistance Rev. 0 | Page 9 of 21 ADA8282 Data Sheet 120 0 GAIN = 18dB GAIN = 24dB GAIN = 30dB GAIN = 36dB 100 –20 –40 CROSSTALK (dB) PSRR (dB) 80 60 40 –60 –80 –100 20 1M 10M 100M FREQUENCY (Hz) –140 10k 100k 1M 10M 100M FREQUENCY (Hz) Figure 21. PSRR vs. Frequency at Various Gains 13132-124 100k 13132-122 0 10k –120 Figure 23. Crosstalk vs. Frequency 37.85 100 90 37.80 SUPPLY CURRENT (mA) 80 60 50 40 30 GAIN = 18dB GAIN = 24dB GAIN = 30dB GAIN = 36dB 10 0 100k 1M 10M FREQUENCY (Hz) 100M 37.75 37.70 37.65 37.60 37.55 –40 –25 10 5 20 35 50 65 80 95 110 TEMPERATURE (°C) Figure 24. Quiescent Supply Current vs. Temperature Figure 22. CMRR vs. Frequency at Various Gains Rev. 0 | Page 10 of 21 125 13132-120 20 13132-123 CMRR (dB) 70 Data Sheet ADA8282 THEORY OF OPERATION The input to the ADA8282 is typically ac-coupled. The ac coupling capacitors operate with the input impedance of the ADA8282 to create a high-pass filter with a pole at 1/(2π2RC), where R = 785 Ω with a typical tolerance of ±15%. RADAR RECEIVE PATH AFE The primary application for the ADA8282 is a high speed ramp, frequency modulated, continuous wave radar (HSR-FMCW radar). Figure 25 shows a simplified block diagram of an HSR-FMCW radar system. The signal chain requires multiple channels, each including an LNA and a PGA. The ADA8282 provides these key components in a single 5 mm × 5 mm LFCSP. POWER MODES The ADA8282 has four power modes that can be controlled through Register 0x14 (BIAS_SEL). The power modes allow a user to adjust the power and performance tradeoffs to suit the end application. Use the low power mode when power savings are in demand, and use the high power mode in applications that require increased bandwidth and low noise. The performance of each component is designed to meet the demands of an HSR-FMCW radar system. Some examples of these performance metrics are the LNA noise, PGA gain range, and signal chain bandwidth and power. The ADA8282 also has adjustable power modes to adjust the power and performance level to accommodate a wide variety of applications. Table 6 shows the power performance trade-offs of the various SPI settings. The ADA8282 is programmable via the SPI. Channel gain, power mode, and offset voltage can be adjusted using the SPI port. Table 6. Power Mode Trade-Offs DEFAULT SPI SETTINGS Mode Setting b’00 b’01 b’10 b’11 When initially powered, the ADA8282 defaults to a setting of 0x00 in Register 0x17, which disables all channels. The device is enabled by writing 0x0F to Register 0x17. INPUT IMPEDANCE Power per Channel (mW) 18.3 26.5 34.8 54.8 Input Referred Noise at 2 MHz (nV/√Hz) 4.5 3.8 3.6 3.4 The input impedance to the ADA8282 is set by an internal 785 Ω resistance at each input, biased to midsupply by an internal voltage buffer. Both the positive and negative inputs are biased with the same network, creating a differential input impedance of 1.57 kΩ. TRANSMIT SIGNAL GENERATION REF. OSCILLATOR CHIRP RAMP GENERATOR VCO ADA8282 DSP LNA PGA 12-BIT ADC LNA PGA 12-BIT ADC LNA PGA 12-BIT ADC ANTENNA Figure 25. Typical Signal Chain Overview Rev. 0 | Page 11 of 21 13132-021 PA Typical Bandwidth (MHz), Gain = 36 dB 20.5 34.2 42.3 52.3 ADA8282 Data Sheet The default setting (0x20) applies a zero offset, 0x00 applies the maximum negative offset, and 0x3F applies the maximum positive offset. PROGRAMMABLE GAIN RANGE The ADA8282 has a programmable gain to allow adjusting of the output amplitudes of signals to accommodate a variety of applications. The gain of the ADA8282 is programmable in 6 dB increments from 18 dB to 36 dB. The gain is controlled using Register 0x15. The same register controls all four channels, but each channel can be independently controlled by utilizing the appropriate bits in the register. Channel A is controlled with the two LSBs of Register 0x15 (Bits[1:0]), Channel B uses Bits[3:2], Channel C uses Bits[5:4], and Channel D uses the two MSBs, Bits[7:6]. The range and resolution of the LNA_OFFSETx adjustments are dependent on the LNA bias mode as described in Table 9. Table 9. Offset Voltage Adjustments LNA_BIAS_SEL Setting b’00 b’01 b’10 b’11 The gain setting and gains are listed in Table 7. Table 7. Gain Settings Referred to Input (RTI) Offset Resolution (μV) 113 186 250 440 RTI Offset Range (mV) ±4 ±6 ±8 ±14 VIO Pin Register 0x15 Setting b’00 b’01 b’10 b’11 Gain (dB) 18 24 30 36 Gain (V/V) 7.9 15.9 31.6 63.1 The VIO pin sets the voltage levels used by the SPI interface. If the VIO pin is tied to the 3.3 V supply, the SPI port functions on 3.3 V logic. SINGLE-ENDED OR DIFFERENTIAL INPUT The ADA8282 operates with either a differential or single-ended signal source. The maximum input voltage swing is the same in either configuration. When using a single-ended signal source, connect the unused input to ground with a capacitor. Matching the ac coupling capacitor to the ac grounding capacitor optimizes CMRR performance. OUTPUT SWING VARIATION WITH GAIN The ADA8282 gain is implemented using two internal gain stages. The first stage is an LNA with a gain of 24 dB, and the second stage is a PGA with a gain that varies from −6 dB to +12 dB. The output of the LNA has a fixed output swing range, and is the limiting factor when the channel gain is 18 dB. Because of the limitations of the LNA swing range, the ADA8282 has an output swing that is dependent on gain, as shown in Table 8. SHORT-CIRCUIT CURRENTS The ADA8282 typically has a 205 mA short-circuit current per output pin. The thermal implications of this current during unintended shorting of these outputs must be taken into account when designing boards with this device. Table 8. Output Swing at Various Gains Gain (dB) 18 24 30 36 Output Swing (V p-p) 3.1 6.3 6.3 6.3 SPI INTERFACE The ADA8282 SPI interface uses a 4-wire interface to deliver a 16-bit instruction header, followed by 8 bits of data. The first bit is a read/write bit. W1 and W0 determine how many bytes are transferred, and must both be zeros for the ADA8282 to write to a single register. Then, a 13-bit address and an 8-bit data byte follow. OFFSET VOLTAGE ADJUSTMENTS Register 0x10 through Register 0x13 adjust the dc offset voltage of each channel. The default value of 0x20 is intended to be the setting for the offset closest to 0 V, but adjustments can be made as required by the application. The SPI port operates at SCLK frequencies of up to 10 MHz. For additional SPI timing information, see the AN-877 Application Note. CS SDI DON’T CARE DON’T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 16-BIT INSTRUCTION HEADER MSB-FIRST 16-BIT INSTRUCTION Figure 26. Serial Instruction Details Rev. 0 | Page 12 of 21 A0 D7 D6 D5 D4 D3 D2 REGISTER (N) DATA D1 D0 DON’T CARE 13132-022 SCLK DON’T CARE Data Sheet ADA8282 CHANNEL TO CHANNEL PHASE MATCHING 350 In a multichannel radar application, matching the ac performance between channels improves the distance and angle resolution of a detected object, particularly the phase matching in the band of interest for the application. The ADA8282 layout and design are optimized to increase phase matching. The ADA8282 also has sufficient bandwidth to minimize any channel to channel phase variation for up to 5 MHz input signals. 300 NUMBER OF HITS 250 200 150 100 The phase mismatch between channels can be calibrated at a single temperature. However, any variation in phase matching over temperature can still degrade system performance. The ADA8282 is characterized to capture the maximum channel to channel phase mismatch as the temperature varies from a calibration temperature of 25°C. Figure 27 shows a distribution of channel to channel phase mismatch for signal frequencies up to 5 MHz. When the initial phase mismatch between channels is normalized to 0° at +25°C, the 6σ mismatch is 0.43° at −40°C and 0.6° at +125°C. TA = +125°C TA = –40°C PHASE MISMATCH (Degrees) Figure 27. Channel to Channel Phase Mismatch, Normalized to 0° at 25°C, LNA_BIAS_SEL = PGA_BIAS_SEL = b’00, PGA_GAIN = b’11 The amount of channel to channel phase mismatch varies with the power mode. Table 10 shows the 6σ phase mismatch up to 5 MHz over the full temperature range for all gain settings in different power modes, when normalized to 0° at 25°C in each power mode. Table 10. Maximum Channel to Channel Phase Mismatch over Temperature After 25°C Calibration PGA_BIAS_SEL b’00 b’01 b’10 b’11 LNA_BIAS_SEL b’00 b’01 b’10 b’11 13132-126 0.35 0.30 0.25 0.20 0.15 0.10 0 0.05 –0.05 –0.10 –0.15 –0.20 –0.25 0 –0.30 50 6σ Channel to Channel Phase Mismatch over Temperature (Degrees) 0.60 0.41 0.33 0.60 Rev. 0 | Page 13 of 21 Maximum Channel to Channel Phase Mismatch (Degrees) ±1 ±1 ±1 ±1 ADA8282 Data Sheet APPLICATIONS INFORMATION INCREASED GAIN USING TWO ADA8282 DEVICES IN SERIES Table 11. Gain Settings for Two Devices in Series For applications that require gains greater than 36 dB, two ADA8282 devices can be used in series with each other. To optimize the signal swing for the path, increment the gains according to Table 11. GPIO: +3.3V/0V 0.1µF 0.1µF 5 25 27 28 29 26 21 20 EPAD TIED TO GROUND 6 19 7 18 8 17 9 0.1µF +3.3V 22 ADA8282 4 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF TO ADC TO ADC TO ADC TO ADC 0.1µF +3.3V 0.1µF +3.3V +3.3V Figure 28. Using Two ADA8282 Devices in Series to Increase Gain Rev. 0 | Page 14 of 21 13132-023 0.1µF 3 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD 16 0.1µF 23 15 0.1µF 2 14 17 0.1µF 24 13 18 8 0.1µF 16 7 0.1µF 1 12 19 0.1µF +INA –INA +INB –INB +INC –INC +IND –IND 11 20 EPAD TIED TO GROUND 6 0.1µF AVDD NIC NIC NIC NIC NIC NIC AVDD 5 21 0.1µF 30 AVDD SDO SDI CS SCLK RESET VIO AVDD 22 ADA8282 4 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD 32 25 26 27 28 29 30 31 32 3 15 0.1µF 23 14 0.1µF 2 13 INPUT D SOURCE 0.1µF 24 12 INPUT C SOURCE 0.1µF 0.1µF 1 11 0.1µF +INA –INA +INB –INB +INC –INC +IND –IND 9 INPUT B SOURCE 0.1µF 10 0.1µF AVDD NIC NIC NIC NIC NIC NIC AVDD INPUT A SOURCE 0.1µF SPI BUS AVDD SDO SDI CS SCLK RESET VIO AVDD SPI BUS +3.3V 10kΩ 31 0.1µF +3.3V +3.3V 10kΩ A2 (Output Side ADA8282) Gain (dB) 18 24 24 24 30 30 36 GPIO: +3.3V/0V 10 +3.3V A1 (Input Side ADA8282) Gain (dB) 18 18 24 30 30 36 36 Total Gain (dB) 36 42 48 54 60 66 72 Data Sheet ADA8282 Figure 29) as long as only one device is enabled at a time. When an ADA8282 is disabled, the outputs present a 6 kΩ load on the output bus. MULTIPLEXING INPUTS USING MULTIPLE ADA8282 DEVICES It is possible to multiplex eight differential inputs down to four differential outputs by using two ADA8282 devices. The devices can be connected such that the outputs are connected (see GPIO: +3.3V/0V +3.3V 0.1µF +3.3V 10kΩ 0.1µF 0.1µF 25 26 27 28 29 30 31 22 ADA8282 4 5 21 20 EPAD TIED TO GROUND 6 19 7 18 8 17 AVDD NIC NIC NIC NIC NIC NIC AVDD 9 0.1µF 3 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD +3.3V 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF +3.3V 0.1µF GPIO: +3.3V/0V +3.3V 0.1µF 16 INPUT D SOURCE 0.1µF 23 15 0.1µF 24 2 14 INPUT C SOURCE 0.1µF 1 13 0.1µF +INA –INA +INB –INB +INC –INC +IND –IND 12 INPUT B SOURCE 0.1µF 11 0.1µF 10 INPUT A SOURCE 32 AVDD SDO SDI CS SCLK RESET VIO AVDD SPI BUS TO ADC +3.3V 10kΩ TO ADC TO ADC 0.1µF 0.1µF SPI BUS 0.1µF 25 26 27 28 29 30 31 22 ADA8282 4 5 21 20 EPAD TIED TO GROUND 6 19 7 18 8 17 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF +3.3V +3.3V Figure 29. Multiplexing by Connecting Two ADA8282 Outputs to One Output Bus Rev. 0 | Page 15 of 21 13132-024 AVDD NIC NIC NIC NIC NIC NIC AVDD 9 0.1µF 3 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD 16 INPUT H SOURCE 0.1µF 23 15 0.1µF 24 2 14 INPUT G SOURCE 0.1µF 1 13 0.1µF +INA –INA +INB –INB +INC –INC +IND –IND 12 INPUT F SOURCE 0.1µF 11 0.1µF 10 INPUT E SOURCE 32 AVDD SDO SDI CS SCLK RESET VIO AVDD TO ADC ADA8282 Data Sheet series with the bypassing paths. AC couple the inputs and outputs for each channel as shown in Figure 30. Pull the RESET pin low with a 10 kΩ resistor and drive it with 3.3 V GPIO logic. The SPI pins can be directly connected to the SPI bus. BASIC CONNECTIONS FOR A TYPICAL APPLICATION The ADA8282 is typically configured to operate with a nominal 3.3 V power supply, using the EPAD as the analog ground connection. Place the bypass capacitors as close as possible to the power supply pins to minimize the length of metal traces in GPIO: +3.3V/0V +3.3V 0.1µF +3.3V 10kΩ 0.1µF 25 27 28 29 30 31 26 22 ADA8282 4 5 21 20 EPAD TIED TO GROUND 6 19 18 8 17 +OUTA –OUTA +OUTB –OUTB +OUTC –OUTC +OUTD –OUTD 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF TO ADC TO ADC TO ADC TO ADC 16 7 15 0.1µF 0.1µF +3.3V +3.3V Figure 30. Typical Component Connections Rev. 0 | Page 16 of 21 13132-025 0.1µF 3 14 INPUT D SOURCE 0.1µF 0.1µF 23 13 0.1µF 24 2 12 INPUT C SOURCE 0.1µF 1 11 0.1µF +INA –INA +INB –INB +INC –INC +IND –IND 9 INPUT B SOURCE 0.1µF 10 0.1µF AVDD NIC NIC NIC NIC NIC NIC AVDD INPUT A SOURCE 32 AVDD SDO SDI CS SCLK RESET VIO AVDD SPI BUS Data Sheet ADA8282 REGISTER MAP REGISTER SUMMARY Table 12. Register Summary Reg. 0x00 0x01 0x04 0x05 0x06 0x10 0x11 0x12 0x13 0x14 0x15 0x17 Name INTF_CONFA SOFT_RESET CHIP_ID1 CHIP_ID2 Revision LNA_OFFSET0 LNA_OFFSET1 LNA_OFFSET2 LNA_OFFSET3 BIAS_SEL PGA_GAIN EN_CHAN Bits Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 [7:0] INTF_CONFA2 LSBFIRST1 INTF_CONFA1 LSBFIRST0 [7:0] Unused [7:0] CHIP_IDLOW [7:0] CHIP_IDHI [7:0] Revision [7:0] Unused LNA_OFFSET0 [7:0] Unused LNA_OFFSET1 [7:0] Unused LNA_OFFSET2 [7:0] Unused LNA_OFFSET3 [7:0] Unused PGA_BIAS_SEL [7:0] PGA_GAIN3 PGA_GAIN2 PGA_GAIN1 [7:0] Unused EN_ EN_ CHANNEL3 CHANNEL2 0x18 EN_BIAS_GEN [7:0] Unused 0x1D SPAREWR0 [7:0] Unused 0x1E SPARERD0 [7:0] Unused Bit 1 Bit 0 INTF_CONFA0 SOFT_RESET Reset 0x00 0x00 0x82 0x82 0x00 0x20 0x20 0x20 0x20 0x0A 0x00 0x00 RW RW R R R R RW RW RW RW RW RW RW LNA_BIAS_SEL PGA_GAIN0 EN_ EN_ CHANNEL1 CHANNEL0 EN_BIAS_GEN 0x00 RW GPIO_WRITE GPIO_WR_ 0x00 RW MODE GPIO_READ 0x00 R REGISTER DETAILS Register 0x00: Interface Configuration Register Bit 7 Bit 6 INTF_CONFA2 Bit 5 LSBFIRST1 Bit 4 Bit 3 INTF_CONFA1 Bit 2 LSBFIRST0 Bit 1 Bit 0 INTF_CONFA0 The INTF_CONFA configuration register is symmetric, as it is the first register written and sets the data direction (LSB first or MSB first). Table 13. INTF_CONFA Configuration Register Bit Descriptions Bits [7:0] 5 [4:3] 2 [1:0] Bit Name INTF_CONFA2 LSBFIRST1 INTF_CONFA1 LSBFIRST0 INTF_CONFA0 Description INTF_CONFA2 must remain b’00. LSBFIRST1 must be set to b’1 for LSB first operation and to b’0 for MSB first operation. INTF_CONFA1 must remain b’00. LSBFIRST0 must be set to b’1 for LSB first operation and to b’0 for MSB first operation. INTF_CONFA0 must remain b’00. Reset 0x00 0x00 0x00 0x00 0x00 Access RW RW RW RW RW Register 0x01: Soft Reset Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Unused Bit 0 SOFT_RESET Table 14. SOFT_RESET Configuration Register Bit Descriptions Bits 0 Bit Name SOFT_RESET Description The SOFT_RESET bit resets all registers to their default values when SOFT_RESET is set to b’1. Reset 0x00 Access RW Register 0x04: Chip ID Low Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 CHIP_IDLOW Bit 2 Bit 1 Bit 0 Table 15. CHIP_IDLOW Configuration Register Bit Descriptions Bits [7:0] Bit Name CHIP_IDLOW Description The CHIP_ID1 and CHIP_ID2 registers identify the ADA8282. Rev. 0 | Page 17 of 21 Reset 0x82 Access R ADA8282 Data Sheet Register 0x05: Chip ID High Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 CHIP_IDHI Bit 2 Bit 1 Bit 0 Table 16. CHIP_IDHI Configuration Register Bit Descriptions Bits [7:0] Bit Name CHIP_IDHI Description The CHIP_ID1 and CHIP_ID2 registers identify the ADA8282. Reset 0x82 Access R Register 0x06: Revision Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Revision Bit 2 Bit 1 Bit 0 Table 17. Revision Configuration Register Bit Descriptions Bits [7:0] Bit Name Revision Description The revision register identifies the silicon revision of the current die. Reset 0x00 Access R Register 0x10: LNA Offset 0 Register Bit 7 Bit 6 Unused Bit 5 Bit 4 Bit 3 Bit 2 LNA_OFFSET0 Bit 1 Bit 0 Table 18. LNA_OFFSET0 Configuration Register Bit Descriptions Bits [5:0] Bit Name LNA_OFFSET0 Description LNA_OFFSET0 controls the offset of Channel A. The default setting (0x20) applies the minimum offset, 0x00 applies the maximum negative offset, and 0x3F applies the maximum positive offset. The resolution of the offset varies with the LNA bias mode as follows: LNA Bias Mode 0: 113 μV RTI offset resolution, ±4 mV range. LNA Bias Mode 1: 186 μV RTI offset resolution, ±6 mV range. LNA Bias Mode 2: 250 μV RTI offset resolution, ±8 mV range. LNA Bias Mode 3: 440 μV RTI offset resolution, ±14 mV range. Reset 0x20 Access RW Register 0x11: LNA Offset 1 Register Bit 7 Bit 6 Unused Bit 5 Bit 4 Bit 3 Bit 2 LNA_OFFSET1 Bit 1 Bit 0 Table 19. LNA_OFFSET1 Configuration Register Bit Descriptions Bits [5:0] Bit Name LNA_OFFSET1 Description LNA_OFFSET0 controls the offset of Channel B. The default setting (0x20) applies the minimum offset, 0x00 applies the maximum negative offset, and 0x3F applies the maximum positive offset. The resolution of the offset varies with the LNA bias mode as follows: LNA Bias Mode 0: 113 μV RTI offset resolution, ±4 mV range. LNA Bias Mode 1: 186 μV RTI offset resolution, ±6 mV range. LNA Bias Mode 2: 250 μV RTI offset resolution, ±8 mV range. LNA Bias Mode 3: 440 μV RTI offset resolution, ±14 mV range. Reset 0x20 Register 0x12: LNA Offset 2 Register Bit 7 Bit 6 Unused Bit 5 Bit 4 Bit 3 Bit 2 LNA_OFFSET2 Rev. 0 | Page 18 of 21 Bit 1 Bit 0 Access RW Data Sheet ADA8282 Table 20. LNA_OFFSET2 Configuration Register Bit Descriptions Bits [5:0] Bit Name LNA_OFFSET2 Description LNA_OFFSET0 controls the offset of Channel C. The default setting (0x20) applies the minimum offset, 0x00 applies the maximum negative offset, and 0x3F applies the maximum positive offset. The resolution of the offset varies with the LNA bias mode as follows: LNA Bias Mode 0: 113 μV RTI offset resolution, ±4 mV range. LNA Bias Mode 1: 186 μV RTI offset resolution, ±6 mV range. LNA Bias Mode 2: 250 μV RTI offset resolution, ±8 mV range. LNA Bias Mode 3: 440 μV RTI offset resolution, ±14 mV range. Reset 0x20 Access RW Register 0x13: LNA Offset 3 Register Bit 7 Bit 6 Unused Bit 5 Bit 4 Bit 3 Bit 2 LNA_OFFSET3 Bit 1 Bit 0 Table 21. LNA_OFFSET3 Configuration Register Bit Descriptions Bits [5:0] Bit Name LNA_OFFSET3 Description LNA_OFFSET0 controls the offset of Channel D. The default setting (0x20) applies the minimum offset, 0x00 applies the maximum negative offset, and 0x3F applies the maximum positive offset. The resolution of the offset varies with the LNA bias mode as follows: LNA Bias Mode 0: 113 μV RTI offset resolution, ±4 mV range. LNA Bias Mode 1: 186 μV RTI offset resolution, ±6 mV range. LNA Bias Mode 2: 250 μV RTI offset resolution, ±8 mV range. LNA Bias Mode 3: 440 μV RTI offset resolution, ±14 mV range. Reset 0x20 Access RW Register 0x14: PGA Bias Register Bit 7 Bit 6 Bit 5 Unused Bit 4 Bit 3 Bit 2 PGA_BIAS_SEL Bit 1 Bit 0 LNA_BIAS_SEL The PGA bias select register allows the user to trade off power and performance (for example, bandwidth and noise). Table 22. BIAS_SEL Configuration Register Bit Descriptions Bits [3:2] [1:0] Bit Name PGA_BIAS_SEL LNA_BIAS_SEL Description Set PGA_BIAS_SEL to b’00 for the minimum PGA bias and to b’11 for the maximum PGA bias. Set LNA_BIAS_SEL to b’00 for the minimum LNA bias and to b’11 for the maximum LNA bias. Reset 0x00 0x00 Access RW RW Register 0x15: PGA Gain Register Bit 7 Bit 6 PGA_GAIN3 Bit 5 Bit 4 PGA_GAIN2 Bit 3 Bit 2 PGA_GAIN1 Bit 1 Bit 0 PGA_GAIN0 The PGA gain register allows independent gain settings for each channel. Table 23. PGA_GAIN Configuration Register Bit Descriptions Bits [7:6] Bit Name PGA_GAIN3 [5:4] PGA_GAIN2 [3:2] PGA_GAIN1 [1:0] PGA_GAIN0 Description Set PGA_GAIN3 to b’00 for 18 dB gain, to b’01 for 24 dB gain, to b’10 for 30 dB gain, and to b’11 for 36 dB gain for Channel D Set PGA_GAIN2 to b’00 for 18 dB gain, to b’01 for 24 dB gain, to b’10 for 30 dB gain, and to b’11 for 36 dB gain for Channel C Set PGA_GAIN1 to b’00 for 18 dB gain, to b’01 for 24 dB gain, to b’10 for 30 dB gain, and to b’11 for 36 dB gain for Channel B Set PGA_GAIN0 to b’00 for 18 dB gain, to b’01 for 24 dB gain, to b’10 for 30 dB gain, and to b’11 for 36 dB gain for Channel A Rev. 0 | Page 19 of 21 Reset 0x00 Access RW 0x00 RW 0x00 RW 0x00 RW ADA8282 Data Sheet Register 0x17: Enable Channel Register Bit 7 Bit 6 Bit 5 Unused Bit 4 Bit 3 EN_CHANNEL3 Bit 2 EN_CHANNEL2 Bit 1 EN_CHANNEL1 Bit 0 EN_CHANNEL0 The enable channel register allows individual channels to be enabled or disabled. The default mode for the channel is disabled. Write 0x0F to the EN_CHAN register to enable all channels. When a channel is disabled but the bias generator is still enabled, the channel’s current consumption is <100 μA. When a channel is disabled, its output pins are high-Z. The enable channel register resets at AVDD power-on to 0x00 to avoid inrush current for fast supply ramps. Table 24. EN_CHAN Register Bit Descriptions Bits 3 2 1 0 Bit Name EN_CHANNEL3 EN_CHANNEL2 EN_CHANNEL1 EN_CHANNEL0 Description Set to b’1 to enable Channel D, and set to b’0 to disable Channel D Set to b’1 to enable Channel C, and set to b’0 to disable Channel C Set to b’1 to enable Channel B, and set to b’0 to disable Channel B Set to b’1 to enable Channel A, and set to b’0 to disable Channel A Reset 0x00 0x00 0x00 0x00 Access RW RW RW RW Register 0x18: Enable Bias Generator Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Unused Bit 0 EN_BIAS_GEN When any channel is enabled, the bias generator is automatically enabled. The EN_BIAS_GEN register controls whether the bias generator stays active, even when all channels are disabled. Leaving the bias generator active decreases the enable time of the device. Table 25. EN_BIAS_GEN Register Bit Descriptions Bits 0 Bit Name EN_BIAS_GEN Description Setting EN_BIAS_GEN to 1 keeps the bias generator active, providing a faster enable time (~2 μs). Reset 0x00 Access RW Register 0x1D: GPIO Write Register Bit 7 Bit 6 Bit 5 Bit 4 Unused Bit 3 Bit 2 Bit 1 GPIO_WRITE Bit 0 GPIO_WR_MODE The GPIO_WR_MODE bit reconfigures the SDO pin to a general-purpose input/output (GPIO) port that can be written by the GPIO_WRITE register or read by the GPIO_READ register. Table 26. SPAREWR0 Configuration Register Bit Descriptions Bits 1 0 Bit Name GPIO_WRITE GPIO_WR_MODE Description Data bit is put onto the SDO pin when GPIO write mode is active. Write b’1 to this register to activate GPIO write mode. Reset 0x00 0x00 Access RW RW Register 0x1E: GPIO Read Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Unused Bit 0 GPIO_READ Table 27. SPARERD0 Configuration Register Bit Descriptions Bits 0 Bit Name GPIO_READ Description This register reflects the logic level placed on SDO when a b’0 is written to GPIO_WR_MODE. Rev. 0 | Page 20 of 21 Reset 0x00 Access R Data Sheet ADA8282 OUTLINE DIMENSIONS 0.30 0.25 0.18 32 25 0.50 BSC 0.80 0.75 0.70 0.50 0.40 0.30 8 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 3.65 3.50 SQ 3.45 EXPOSED PAD 17 TOP VIEW PIN 1 INDICATOR 1 24 9 BOTTOM VIEW 0.25 MIN 3.50 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. 04-02-2012-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 Figure 31. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm × 5 mm Body, Very Very Thin Quad (CP-32-11) Dimensions shown in millimeters ORDERING GUIDE Model1, 2 ADA8282WBCPZ-R7 ADA8282WBCPZ ADA8282CP-EBZ 1 2 Temperature Range −40°C to +125°C −40°C to +125°C Package Description 32-Lead LFCSP_WQ, 7” Tape and Reel 32-Lead LFCSP_WQ Evaluation Board Package Option CP-32-11 CP-32-11 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The ADA8282W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. ©2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D13132-0-7/15(0) Rev. 0 | Page 21 of 21