Wideband Quadrature Modulator with Integrated Fractional-N PLL and VCOs ADRF6720-27 Data Sheet FEATURES GENERAL DESCRIPTION I/Q modulator with integrated fractional-N PLL RF output frequency range: 400 MHz to 3000 MHz Internal LO frequency range: 356.25 MHz to 2855 MHz Output P1dB: 10.8 dBm at 2140 MHz Output IP3: 31.1 dBm at 2140 MHz Carrier feedthrough: −44.3 dBm at 2140 MHz Sideband suppression: −40.8 dBc at 2140 MHz Noise floor: −159.5 dBm/Hz at 2140 MHz Baseband 1 dB modulation bandwidth: >1000 MHz Baseband input bias level: 2.68 V Power supply: 3.3 V/425 mA Integrated RF tunable balun allowing single-ended RF output Multicore integrated VCOs HD3/IP3 optimization Sideband suppression and carrier feedthrough optimization High-side/low-side LO injection Programmable via 3-wire serial port interface (SPI) 40-lead 6 mm × 6 mm LFCSP The ADRF6720-27 is a wideband quadrature modulator with an integrated synthesizer ideally suited for 3G and 4G communication systems. The ADRF6720-27 consists of a high linearity broadband modulator, an integrated fractional-N phase-locked loop (PLL), and four low phase noise multicore voltage controlled oscillators (VCOs). The ADRF6720-27 local oscillator (LO) signal can be generated internally via the on-chip integer-N and fractional-N synthesizers, or externally via a high frequency, low phase noise LO signal. The internal integrated synthesizer enables LO coverage from 356.25 MHz to 2855 MHz using the multicore VCOs. In the case of internal LO generation or external LO input, quadrature signals are generated with a divide by 2 phase splitter. When the ADRF6720-27 is operated with an external 1 × LO input, a polyphase filter generates the quadrature inputs to the mixer. The ADRF6720-27 offers digital programmability for carrier feedthrough optimization, sideband suppression, HD3/IP3 optimization, and high-side or low-side LO injection. APPLICATIONS The ADRF6720-27 is fabricated using an advanced silicongermanium BiCMOS process. It is available in a 40-lead, RoHS-compliant, 6 mm × 6 mm LFCSP package with an exposed pad. Performance is specified over the −40°C to +85°C temperature range. 2G/3G/4G/LTE broadband communication systems Microwave point-to-point radios Satellite modems Military/aerospace Instrumentation FUNCTIONAL BLOCK DIAGRAM VPOSx 40 30 26 22 17 11 6 3 ADRF6720-27 V TO I I– 4 LO NULLING DAC LO NULLING DAC Q– 8 27 ENBL 24 RFOUT 18 LOOUT+ 19 LOOUT– 15 CS 14 SCLK 13 SDIO PHASE CORRECTION PHASE CORRECTION V TO I Q+ 9 REFIN 39 CP 36 VTUNE 32 LOIN– 33 LOIN+ 34 PLL QUAD DIVIDER POLYPHASE FILTER 2 5 7 10 16 20 23 25 29 37 38 LDO 2.5V LDO VCO 12 28 DECL1 DECL2 SERIAL PORT INTERFACE 31 DECL3 GND 12488-001 I+ 35 Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2014–2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADRF6720-27 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 LO Input ...................................................................................... 24 Applications ....................................................................................... 1 Loop Filter ................................................................................... 24 General Description ......................................................................... 1 RF Output .................................................................................... 24 Functional Block Diagram .............................................................. 1 Applications Information .............................................................. 25 Revision History ............................................................................... 2 DAC to I/Q Modulator Interfacing .......................................... 25 Specifications..................................................................................... 3 Baseband Bandwidth ................................................................. 26 Timing Characteristics ................................................................ 7 Carrier Feedthrough Nulling .................................................... 26 Absolute Maximum Ratings............................................................ 8 Sideband Suppression Optimization ....................................... 26 Thermal Resistance ...................................................................... 8 Linearity....................................................................................... 27 ESD Caution .................................................................................. 8 LO Amplitude and Common-Mode Voltage.......................... 27 Pin Configuration and Function Descriptions ............................. 9 Operating Out of Frequency Range ......................................... 28 Typical Performance Characteristics ........................................... 11 Spurious Performance ............................................................... 28 Theory of Operation ...................................................................... 18 Layout .......................................................................................... 29 LO Generation Block ................................................................. 18 Characterization Setups ................................................................. 30 Baseband ...................................................................................... 21 Register Map ................................................................................... 32 Active Mixers .............................................................................. 21 Register Details ............................................................................... 33 Serial Port Interface .................................................................... 22 Outline Dimensions ....................................................................... 43 Basic Connections for Operation ................................................. 23 Ordering Guide .......................................................................... 43 Power Supply and Grounding ................................................... 23 Baseband Inputs.......................................................................... 24 REVISION HISTORY 9/15—Rev. A to Rev. B Changed RFOUT = 4 dBm to RFOUT ≈ 4 dBm, and USB to Sideband Suppression ................................................... Throughout Changes to Spurious Performance Section and Figure 59 ........ 28 Changes to Figure 60 ...................................................................... 29 3/15—Rev. 0 to Rev. A Added Spurious Performance Section and Figure 57 to Figure 59; Renumbered Sequentially ........................................... 28 Added Figure 60 ............................................................................. 29 10/14—Revision 0: Initial Version Rev. B | Page 2 of 43 Data Sheet ADRF6720-27 SPECIFICATIONS VPOSx = 3.3 V, TA = 25°C; baseband I/Q amplitude = 1 V p-p differential sine waves in quadrature with a 2.68 V dc bias, unless otherwise noted. Table 1. Parameter OPERATING FREQUENCY RANGE RF OUTPUT = 460 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Output IP2 Output IP3 Noise Floor RF OUTPUT = 940 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Output IP2 Output IP3 Noise Floor RF OUTPUT = 1900 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Test Conditions/Comments RF output range Internal LO range External LO range Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) Rev. B | Page 3 of 43 Min 400 356.25 400 Typ Max 3000 2855 3000 Unit MHz MHz MHz −0.7 −4.68 6.1 −53.0 −50.2 0.18 0.023 −77.1 −61.5 58.1 dBm dB dBm dBm dBc Degrees dB dBc dBc dBm 27.2 dBm −161.2 dBm/Hz −160.1 dBm/Hz 5.0 1.02 11.75 −45.5 −47.3 −0.05 0.022 −69.5 −60.6 65.8 dBm dB dBm dBm dBc Degrees dB dBc dBc dBm 34.8 dBm −158.2 dBm/Hz −157.3 dBm/Hz 4.5 0.52 11.4 −37.5 −40.4 1.21 0.006 −65.0 −61.4 dBm dB dBm dBm dBc Degrees dB dBc dBc ADRF6720-27 Parameter Output IP2 Output IP3 Noise Floor RF OUTPUT = 2140 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Output IP2 Output IP3 Noise Floor RF OUTPUT = 2300 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Output IP2 Output IP3 Noise Floor RF OUTPUT = 2600 MHz Output Power, POUT Modulator Voltage Gain Output P1dB Carrier Feedthrough Sideband Suppression Quadrature Error I/Q Amplitude Balance Second Harmonic Third Harmonic Output IP2 Data Sheet Test Conditions/Comments f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Baseband VIQ = 1 V p-p differential POUT − P(fLO ± (2 × fBB)) POUT − P(fLO ± (3 × fBB)) f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential Rev. B | Page 4 of 43 Min Typ 59.8 Max Unit dBm 32.7 dBm −157.5 dBm/Hz −156.6 dBm/Hz 4.0 0.02 10.8 −44.3 −40.8 −0.78 −0.015 −58.4 −67.3 58.7 dBm dB dBm dBm dBc Degrees dB dBc dBc dBm 31.1 dBm −159.5 dBm/Hz −158.6 dBm/Hz 3.5 −0.48 10.3 −40.8 −37.4 −1.38 −0.015 −58.8 −65.8 57.5 dBm dB dBm dBm dBc Degrees dB dBc dBc dBm 28.1 dBm −158.6 −157.5 dBm/Hz dBm/Hz 2.9 −1.08 9.9 −37.1 −40.7 −0.80 0.003 −61.2 −59.1 53.5 dBm dB dBm dBm dBc Degrees dB dBc dBc dBm Data Sheet Parameter Output IP3 Noise Floor SYNTHESIZER SPECIFICATIONS Figure of Merit (FOM)1 REFERENCE CHARACTERISTICS REFIN Input Frequency REFIN Input Amplitude Phase Detector Frequency MUXOUT Output Level MUXOUT Duty Cycle CHARGE PUMP Charge Pump Current Output Compliance Range PHASE NOISE, FREQUENCY = 460 MHz, fPFD = 38.4 MHz Integrated Phase Noise Reference Spurs PHASE NOISE, FREQUENCY = 940 MHz, fPFD = 38.4 MHz Integrated Phase Noise Reference Spurs PHASE NOISE, FREQUENCY = 1900 MHz, fPFD = 38.4 MHz Integrated Phase Noise ADRF6720-27 Test Conditions/Comments f1BB = 3.5 MHz, f2BB = 4.5 MHz, baseband I/Q amplitude per tone = 0.3 V p-p differential I/Q input with 2.68 V dc bias and no RF output, 20 MHz carrier offset I/Q input with 2.68 V dc bias and −10 dBm RF output, 20 MHz carrier offset Synthesizer specifications referenced to the modulator output Min Typ 27.9 Max Unit dBm −158.6 dBm/Hz −157.3 dBm/Hz −218.5 dBc/Hz/Hz REFIN, MUXOUT pins 5.7 320 4 11.4 Low (lock detect output selected) High (lock detect output selected) 40 0.25 2.7 50 Programmable to 250 µA, 500 µA, 750 µA, or 1000 µA 1000 1 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs fPFD fPFD × 2 fPFD × 3 fPFD × 4 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs fPFD fPFD × 2 fPFD × 3 fPFD × 4 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs Rev. B | Page 5 of 43 2.8 MHz dBm MHz V V % µA V −102.1 −125.2 −144.4 −149.6 −150.8 −150.6 0.09 −97.7 −93.3 −91.5 −96.2 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms dBc dBc dBc dBc −97.9 −121.3 −144.3 −153.7 −154.3 −154.7 0.15 −99.2 −92.3 −95.2 −101.3 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms dBc dBc dBc dBc −92.2 −114.8 −139.8 −151.4 −152.8 −153.4 0.31 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms ADRF6720-27 Parameter Reference Spurs PHASE NOISE, FREQUENCY = 2140 MHz, fPFD = 38.4 MHz Integrated Phase Noise Reference Spurs PHASE NOISE, FREQUENCY = 2300 MHz, fPFD = 38.4 MHz Integrated Phase Noise Reference Spurs PHASE NOISE, FREQUENCY = 2600 MHz, fPFD = 38.4 MHz Integrated Phase Noise Reference Spurs LO INPUT/OUTPUT LO Output Frequency Range LO Output Level LO Input Level LO Input Impedance Data Sheet Test Conditions/Comments fPFD fPFD × 2 fPFD × 3 fPFD × 4 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs fPFD fPFD × 2 fPFD × 3 fPFD × 4 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs fPFD fPFD × 2 fPFD × 3 fPFD × 4 Closed-loop operation (20 kHz loop filter, see Figure 44 for loop filter design) 10 kHz offset 100 kHz offset 1 MHz offset 5 MHz offset 10 MHz offset 20 MHz offset 1 kHz to 40 MHz integration bandwidth, with spurs fPFD fPFD × 2 fPFD × 3 fPFD × 4 Min 1 × LO mode 2 × LO mode 2 × LO or 1 × LO mode, into a 50 Ω load, LO buffer enabled at 2140 MHz LO_DRV_LVL = 0 LO_DRV_LVL = 1 LO_DRV_LVL = 2 Externally applied LO, PLL disabled Externally applied LO, PLL disabled 356.25 712.5 Rev. B | Page 6 of 43 −6 Typ −93.2 −86.8 −89.8 −101.7 Max Unit dBc dBc dBc dBc −92.9 −116.2 −140.3 −150.7 −151.8 −152.5 0.29 −91.3 −90.3 −85.6 −91.0 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms dBc dBc dBc dBc −94.6 −114.8 −139.0 −149.4 −151.1 −151.5 0.26 −96.1 −91.9 −88.2 −94.8 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms dBc dBc dBc dBc −92.4 −111.4 −137.2 −147.7 −148.9 −149.9 0.36 −95.5 −85.4 −93.4 −91.0 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz °rms dBc dBc dBc dBc 2855 5710 −5.8 −1.0 2.2 0 50 +6 MHz MHz dBm dBm dBm dBm Ω Data Sheet ADRF6720-27 Parameter BASEBAND INPUTS I and Q Input DC Bias Level Bandwidth Differential Input Impedance Differential Input Capacitance OUT ENABLE Turn-On Settling Time Test Conditions/Comments I± and Q± pins Min DIGITAL LOGIC Input Voltage High (VIH) Input Voltage Low (VIL) Input Current (IIH/IIL) Input Capacitance (CIN) Output Voltage High (VOH) Output Voltage Low (VOL) POWER SUPPLIES Voltage Range Supply Current Max Unit 1 dB Frequency = 100 MHz2 2.68 >1000 55 V MHz KΩ Frequency = 100 MHz2 0.97 pF 170 ns 10 ns ENBL pin ENBL low to high (90% of envelope), when Register 0x01[10] = 1, Register 0x10[10] = 1 ENBL high to low (10% of envelope), when Register 0x01[10] = 1, Register 0x10[10] = 1 SCLK, SDIO, CS, and ENBL Turn-Off Settling Time Typ 1.4 V V µA pF V V 0.7 +1 −1 5 IOH = −100 µA IOL = +100 µA 2.3 0.2 VPOSx Tx mode at internal LO mode (PLL, internal VCO , and modulator enabled, LO output driver disabled) Tx mode at external 1× LO mode (PLL, internal VCO disabled, modulator enabled, LO output driver disabled) LO output driver; LO_DRV_LVL bits (Register 0x22[7:6]) = 10 Power-down mode 3.3 425 V mA 218 mA 42 14.5 mA mA The figure of merit (FOM) is computed as phase noise (dBc/Hz) – 10log10(fPFD) − 20log10(fLO/fPFD). The FOM was measured across the full LO range, with fREF = 153.6 MHz, fREF power = 4 dBm with a 38.4 MHz fPFD. The FOM was computed at a 50 kHz offset. 2 Refer to Figure 47 for a plot of input impedance over frequency. 1 TIMING CHARACTERISTICS Table 2. Parameter tSCLK tDS tDH tS tH tHIGH tLOW tACCESS tz Description Serial clock period Setup time between data and rising edge of SCLK Hold time between data and rising edge of SCLK Setup time between falling edge of CS and SCLK Hold time between rising edge of CS and SCLK Minimum period that SCLK should be in a logic high state Minimum period that SCLK should be in a logic low state Maximum time delay between falling edge of SCLK and output data valid for a read operation Maximum time delay between CS deactivation and SDIO bus return to high impedance tHIGH tDS tS Min 38 8 8 10 10 10 10 Max 13 5 Unit ns ns ns ns ns ns ns ns ns tH tSCLK tACCESS tLOW tDH Typ CS DON'T CARE DON'T CARE tZ SDIO DON'T CARE A6 A5 A4 A3 A2 A1 A0 R/W D15 D14 D13 Figure 2. Serial Port Timing Diagram Rev. B | Page 7 of 43 D3 D2 D1 D0 DON'T CARE 12488-002 SCLK ADRF6720-27 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 3. Parameter Supply Voltage I+, I−, Q+, Q− LOIN+, LOIN− REFIN ENBL VTUNE CS, SCLK, SDIO Maximum Junction Temperature Operating Temperature Range Storage Temperature Range θJA is thermal resistance, junction to ambient (°C/W), and θJC is thermal resistance, junction to case (°C/W). Rating −0.3 V to +3.6 V −0.5 V to +3.6 V 16 dBm differential −0.3 V to +3.6 V −0.3 V to +3.6 V −0.3 V to +3.6 V −0.3 V to +3.6 V 150°C −40°C to +85°C −65°C to +150°C Table 4. Thermal Resistance Package Type 40-Lead LFCSP 1 θJA1 30.23 θJC1 0.44 Unit °C/W See JEDEC standard JESD51-2 for information on optimizing thermal impedance. ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. B | Page 8 of 43 Data Sheet ADRF6720-27 40 39 38 37 36 35 34 33 32 31 VPOS8 REFIN GND GND CP VPOS7 LOIN+ LOIN– VTUNE DECL3 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADRF6720-27 TOP VIEW (Not to Scale) 30 29 28 27 26 25 24 23 22 21 VPOS6 GND DECL2 ENBL VPOS5 GND RFOUT GND VPOS4 NIC NOTES 1. NIC = NOT INTERNALLY CONNECTED. 2. SOLDER THE EXPOSED PAD TO A LOW IMPEDANCE GROUND PLANE. 12488-003 VPOS2 DECL1 SDIO SCLK CS GND VPOS3 LOOUT+ LOOUT– GND 11 12 13 14 15 16 17 18 19 20 MUXOUT 1 GND 2 I+ 3 I– 4 GND 5 VPOS1 6 GND 7 Q– 8 Q+ 9 GND 10 Figure 3. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 Mnemonic MUXOUT 2, 10 3, 4 5, 7 6 8, 9 11 12 13 14 15 16 17 18, 19 GND I+, I− GND VPOS1 Q−, Q+ VPOS2 DECL1 SDIO SCLK CS GND VPOS3 LOOUT+, LOOUT− GND NIC VPOS4 GND RFOUT VPOS5 ENBL 20 21 22 23, 25 24 26 27 28 29 30 31 32 33, 34 35 DECL2 GND VPOS6 DECL3 VTUNE LOIN−, LOIN+ VPOS7 Description Multiplexer Output. This output allows a digital lock detect signal, a voltage proportional to absolute temperature (VPTAT), or a buffered, frequency-scaled reference signal to be accessed externally. The output is selected by programming Bits[6:4] in Register 0x21. Baseband Ground. Differential In-Phase Baseband Inputs. Mixer Core (I and Q) Ground. 3.3 V Supply Voltage for Baseband. Decouple VPOS1 with 100 pF and 0.1 µF capacitors located close to the pin. Differential Quadrature Baseband Inputs. 3.3 V Supply Voltage for 2.5 V LDO. Decouple VPOS2 with 100 pF and 0.1 µF capacitors located close to the pin. Decoupling Pin for 2.5 V LDO. Connect 100 pF, 0.1 µF, and 10 µF capacitors between this pin and ground. Serial Data Input/Output for SPI. Serial Clock Input/Output for SPI. Chip Select Input/Output for SPI. Digital Ground. 3.3 V Supply Voltage for LO. Decouple VPOS3 with 100 pF and 0.1 µF capacitors located close to the pin. Differential LO Outputs. Either the internally generated LO or external 1 × LO/2 × LO is available at 1 × LO or 2 × LO on these pins. LO Ground. Not Internally Connected. This pin can be left open or tied to RF ground. 3.3 V Supply Voltage for RF. Decouple VPOS4 with 100 pF and 0.1 µF capacitors located close to the pin. RF Ground. Single-Ended 0 V DC RF Output. 3.3 V Supply Voltage for RF. Decouple VPOS5 with 100 pF and 0.1 µF capacitors located close to the pin. Enables/Disables the Circuit Blocks. References the settings at Register 0x01 and Register 0x10. Refer to the ENBL section for more information. Decoupling Pin for VCO LDO. Connect 100 pF, 0.1 µF, and 10 µF capacitors between this pin and ground. VCO Ground. 3.3 V Supply Voltage for VCO LDO. Decouple VPOS6 with 100 pF and 0.1 µF capacitors located close to the pin. Decoupling Pin for VCO LDO. Connect 100 pF, 0.1 µF, and 10 µF capacitors between this pin and ground. VCO Tuning Voltage. Differential External LO Inputs. 3.3 V Supply Voltage for Charge Pump. Decouple VPOS7 with 100 pF and 0.1 µF capacitors located close to the pin. Rev. B | Page 9 of 43 ADRF6720-27 Pin No. 36 37 38 39 40 Mnemonic CP GND GND REFIN VPOS8 EP Data Sheet Description Charge Pump Output. Charge Pump Ground. PLL Reference Ground. PLL Reference Input. 3.3 V Supply Voltage for PLL Reference. Decouple VPOS8 with 100 pF and 0.1 µF capacitors located close to the pin. Exposed Pad. Solder the exposed pad to a low impedance ground plane. Rev. B | Page 10 of 43 Data Sheet ADRF6720-27 TYPICAL PERFORMANCE CHARACTERISTICS VPOSx = 3.3 V; TA = 25°C; baseband I/Q amplitude = 1 V p-p differential sine waves in quadrature with a 2.68 V dc bias; baseband I/Q frequency (fBB) = 1 MHz; fPFD = 38.4 MHz; fREF = 153.6 MHz at 4 dBm referred to 50 Ω (1 V p-p); 20 kHz loop filter, unless otherwise noted. 8 6 SSB OUTPUT POWER (dBm) 4 2 0 –2 –4 –6 1900 2400 1dB OUTPUT COMPRESSION (dBm) 1dB OUTPUT COMPRESSION (dBm) 14 TA = –40°C TA = +25°C TA = +85°C 10 8 6 4 2 1400 1900 2400 LO FREQUENCY (MHz) 1900 2400 3.15 3.30 3.45 10 8 6 4 2 900 1400 1900 2400 Figure 8. SSB 1 dB Output Compression Point (OP1dB) vs. LO Frequency (fLO) and Supply 0 TA = –40°C TA = +25°C TA = +85°C –10 CARRIER FEEDTHROUGH (dBm) CARRIER FEEDTHROUGH (dBm) 1400 LO FREQUENCY (MHz) Figure 5. SSB 1 dB Output Compression Point (OP1dB) vs. LO Frequency (fLO) and Temperature; Multiple Devices Shown –20 –30 –40 –50 –60 –70 –80 TA = –40°C TA = +25°C TA = +85°C –20 –30 –40 –50 –60 –70 –80 900 1400 1900 LO FREQUENCY (MHz) 2400 –90 400 12488-006 –90 400 12 0 400 12488-005 900 900 Figure 7. SSB Output Power (POUT) vs. LO Frequency (fLO) and Supply 12 –10 0 LO FREQUENCY (MHz) 16 0 2 –4 400 Figure 4. Single Sideband (SSB) Output Power (POUT) vs. LO Frequency (fLO) and Temperature; Multiple Devices Shown 0 400 4 12488-007 1400 12488-004 900 LO FREQUENCY (MHz) 14 6 –2 –8 –10 400 3.15 3.30 3.45 12488-008 SSB OUTPUT POWER (dBm) 8 10 TA = –40°C TA = +25°C TA = +85°C 900 1400 1900 LO FREQUENCY (MHz) Figure 6. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature Before Nulling; Multiple Devices Shown 2400 12488-009 10 Figure 9. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature After Nulling Using DCOFF_I and DCOFF_Q at 25°C; Multiple Devices Shown Rev. B | Page 11 of 43 ADRF6720-27 0 0 TA = –40°C TA = +25°C TA = +85°C –20 –30 –40 –50 –60 –70 –80 –20 –30 –40 –50 –60 –70 2400 –90 400 LO FREQUENCY (MHz) Figure 13. Sideband Suppression vs. LO Frequency (fLO) and Temperature After Nulling Using I_LO and Q_LO at 25°C; Multiple Devices Shown 80 –20 70 THIRD-ORDER HARMONIC (dBc), SECOND-ORDER HARMONIC (dBc) 60 50 40 30 OIP3 20 TA = –40°C TA = +25°C TA = +85°C 900 1400 1900 2400 LO FREQUENCY (MHz) –30 THIRD-ORDER DISTORTION (dBC) –10 0 –50 –5 –10 –15 –70 –80 900 1400 1900 2400 20 SSB OUTPUT POWER (dBm) 5 SIDEBAND SUPPRESSION (dBC) –70 15 –40 –60 –60 0 10 CARRIER FEEDTHROUGH (dBm) –50 20 SECOND-ORDER DISTORTION (dBc), THIRD-ORDER DISTORTION (dBc), CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION (dBc) –20 –40 Figure 14. Second- and Third-Order Harmonics vs. LO Frequency (fLO) and Temperature (POUT ≈ 5 dBm) SSB OUTPUT POWER (dBm) SSB OUTPUT POWER (dBm) –10 –30 LO FREQUENCY (MHz) Figure 11. OIP3 and OIP2 vs. LO Frequency (fLO) and Temperature (POUT ≈ −5 dBm per Tone); Multiple Devices Shown 0 TA = –40°C TA = +25°C TA = +85°C SECOND HARMONIC THIRD HARMONIC –90 400 12488-011 OUTPUT IP3 AND IP2 (dBm) OIP2 0 400 2400 1900 LO FREQUENCY (MHz) Figure 10. Sideband Suppression vs. LO Frequency (fLO) and Temperature Before Nulling; Multiple Devices Shown 10 1400 900 12488-014 1900 15 THIRD-ORDER DISTORTION (dBc) 10 –20 SIDEBAND SUPPRESSION (dBc) –30 5 CARRIER FEEDTHROUGH (dBm) –40 0 –50 –5 –10 –60 SECOND-ORDER DISTORTION (dBc) SSB OUTPUT POWER (dBm) 1400 12488-010 900 12488-013 –80 –90 400 SECOND-ORDER DISTORTION (dBc), THIRD-ORDER DISTORTION (dBc), CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION (dBc) TA = –40°C TA = +25°C TA = +85°C –10 SIDEBAND SUPPRESSION (dBc) –10 SIDEBAND SUPPRESSION (dBc) Data Sheet –15 –70 1 –20 10 BASEBAND INPUT VOLTAGE (Vp-p Differential) Figure 12. SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, and Sideband Suppression vs. Baseband Differential Input Voltage (fOUT = 940 MHz) –80 0.1 12488-012 –80 0.1 1 –20 10 BASEBAND INPUT VOLTAGE (Vp-p Differential) Figure 15. SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, and Sideband Suppression vs. Baseband Differential Input Voltage (fOUT = 2140 MHz) Rev. B | Page 12 of 43 12488-015 SECOND-ORDER DISTORTION(dBC) Data Sheet ADRF6720-27 –10 –20 –30 SIDEBAND SUPPRESSION (dBc) 20 0 15 –20 10 CARRIER FEEDTHROUGH (dBm) 5 –40 0 –50 –5 –60 –10 SECOND-ORDER DISTORTION (dBc) –70 TA = –40°C TA = +25°C TA = +85°C –40 PHASE NOISE (dBc/Hz) THIRD-ORDER DISTORTION (dBc) SSB OUTPUT POWER (dBm) SSB OUTPUT POWER (dBm) SECOND-ORDER DISTORTION (dBc), THIRD-ORDER DISTORTION (dBc), CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION (dBc) 0 –60 –80 –100 –120 –140 –15 1 12488-016 –20 10 BASEBAND INPUT VOLTAGE (Vp-p Differential) –180 1k 10k 100k 1M 10M OFFSET FREQUENCY (Hz) Figure 16. SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, and Sideband Suppression vs. Baseband Differential Input Voltage (fOUT = 2600 MHz) 0 TA = –40°C TA = +25°C TA = +85°C –20 PHASE NOISE (dBc/Hz) –40 –60 –80 –100 –120 –80 –100 –120 –140 –160 –160 –180 1k 10k 100k 1M 10M OFFSET FREQUENCY (Hz) Figure 17. Closed-Loop Phase Noise vs. Offset Frequency and Temperature, fLO = 1900 MHz; 20 kHz Loop Filter 0 –20 –180 1k 100k 1M 10M Figure 20. Closed-Loop Phase Noise vs. Offset Frequency and Temperature, fLO = 2140 MHz; 20 kHz Loop Filter 0 TA = –40°C TA = +25°C TA = +85°C –20 TA = –40°C TA = +25°C TA = +85°C –40 PHASE NOISE (dBc/Hz) –60 –80 –100 –120 –60 –80 –100 –120 –140 –140 –160 –160 10k 100k 1M OFFSET FREQUENCY (Hz) 10M –180 1k 12488-018 –180 1k 10k OFFSET FREQUENCY (Hz) –40 PHASE NOISE (dBc/Hz) –60 –140 12488-017 PHASE NOISE (dBc/Hz) –40 TA = –40°C TA = +25°C TA = +85°C 12488-020 –20 Figure 19. Closed-Loop Phase Noise vs. Offset Frequency and Temperature, fLO = 940 MHz; 20 kHz Loop Filter Figure 18. Closed-Loop Phase Noise vs. Offset Frequency and Temperature, fLO = 2300 MHz; 20 kHz Loop Filter 10k 100k 1M OFFSET FREQUENCY (Hz) 10M 12488-021 0 12488-019 –160 –80 0.1 Figure 21. Closed-Loop Phase Noise vs. Offset Frequency and Temperature, fLO = 2600 MHz; 20 kHz Loop Filter Rev. B | Page 13 of 43 ADRF6720-27 Data Sheet –80 TA = –40°C TA = +25°C TA = +85°C –90 –80 –90 OFFSET = 1kHz –110 OFFSET = 100kHz –120 –130 –140 OFFSET = 5MHz 2400 –170 400 TA = –40°C TA = +25°C TA = +85°C SPUR LEVEL (dBc) –85 –90 –95 –100 –105 –95 –100 –105 –110 –115 –115 1900 2400 LO FREQUENCY (MHz) Figure 23. PLL Reference Spurs vs. LO Frequency (1 × PFD and 3 × PFD) at Modulator Output –120 400 1400 1900 2400 Figure 26. PLL Reference Spurs vs. LO Frequency (1 × PFD and 3 × PFD) at LO Output TA = –40°C TA = +25°C TA = +85°C –75 –85 SPUR LEVEL (dBc) –80 –85 –90 –95 –100 –105 –90 –95 –100 –105 –110 –110 –115 –115 1900 LO FREQUENCY (MHz) 2400 –120 400 12488-024 1400 900 –70 2× PFD FREQUENCY 4× PFD FREQUENCY 900 TA = –40°C TA = +25°C TA = +85°C 1× PFD FREQUENCY 3× PFD FREQUENCY LO FREQUENCY (MHz) –80 –120 400 2400 –90 –110 –70 1900 –75 –85 –75 1400 Figure 25. Closed-Loop Phase Noise vs. LO Frequency at 10 kHz, 1 MHz, and 10 MHz Offsets –80 1400 900 –70 1× PFD FREQUENCY 3× PFD FREQUENCY 900 TA = –40°C TA = +25°C TA = +85°C OFFSET = 10MHz LO FREQUENCY (MHz) –80 –120 400 OFFSET = 1MHz 12488-025 1900 12488-023 SPUR LEVEL (dBc) –140 12488-026 1400 12488-022 900 Figure 22. Closed-Loop Phase Noise vs. LO Frequency at 1 kHz, 100 kHz, and 5 MHz Offsets –75 –130 –160 LO FREQUENCY (MHz) –70 –120 –150 –160 –170 400 –110 Figure 24. PLL Reference Spurs vs. LO Frequency (2 × PFD and 4 × PFD) at Modulator Output TA = –40°C TA = +25°C TA = +85°C 2× PFD FREQUENCY 4× PFD FREQUENCY 900 1400 1900 LO FREQUENCY (MHz) 2400 12488-027 –150 SPUR LEVEL (dBc) OFFSET = 10kHz –100 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) –100 Figure 27. PLL Reference Spurs vs. LO Frequency (2 × PFD and 4 × PFD) at LO Output Rev. B | Page 14 of 43 ADRF6720-27 2.8 0.9 2.6 0.8 2.4 0.7 2.2 0.6 2.0 VTUNE (V) 1 0.5 0.4 1.6 1.2 0.2 TA = –40°C TA = +25°C TA = +85°C 900 1400 1900 1.0 2400 0.8 2800 LO FREQUENCY (MHz) –60 –60 PHASE NOISE (dBc/Hz) 4800 5300 5800 –80 –100 –120 –80 –100 –120 –140 10k 100k 1M 10M 100M FREQUENCY (Hz) –160 12488-029 1k Figure 29. Open-Loop VCO Phase Noise for VCO 0 Measured at 2302.24 MHz, 2578.49 MHz, and 2858.07 MHz (VCO ÷ 2) –60 PHASE NOISE (dBc/Hz) –60 –120 10k 100k 1M 10M 100M Figure 32. Open-Loop VCO Phase Noise for VCO 1 Measured at 2009.39 MHz, 2156.68 MHz, and 2303.74 MHz (VCO ÷ 2) –40 –100 1k FREQUENCY (Hz) –40 –80 2303.74MHz 2156.68MHz 2009.39MHz 12488-032 2858.07MHz 2578.49MHz 2302.24MHz –80 –100 –120 –140 –140 2011.44MHz 1880.53MHz 1750.79MHz 10k 100k 1M FREQUENCY (Hz) 10M 100M –160 12488-030 1k Figure 30. Open-Loop VCO Phase Noise for VCO 2 Measured at 1750.79 MHz, 1880.53 MHz, and 2011.44 MHz (VCO ÷ 2) 1750.85MHz 1588.9MHz 1425.84MHz 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M 12488-033 PHASE NOISE (dBc/Hz) –40 –140 PHASE NOISE (dBc/Hz) 4300 Figure 31. VTUNE vs. VCO Frequency and Temperature –40 –160 3800 VCO FREQUENCY (MHz) Figure 28. Integrated Phase Noise with Spurs vs. LO Frequency and Temperature –160 3300 12488-031 0.1 0 400 1.8 1.4 0.3 12488-028 INTEGRATED PHASE NOISE (°rms) Data Sheet Figure 33. Open-Loop VCO Phase Noise for VCO 3 Measured at 1425.84 MHz, 1588.9 MHz, and 1750.85 MHz (VCO ÷ 2) Rev. B | Page 15 of 43 ADRF6720-27 Data Sheet 100 5 450 940 1900 2140 2300 2600 80 70 60 50 40 30 20 2 1 LO_DRV_LVL = 1 0 –1 –2 –3 –4 LO_DRV_LVL = 0 –5 –6 12488-034 NOISE FLOOR (dBm/Hz) –8 400 0.48 TA = –40°C TA = +25°C TA = +85°C 60 50 40 30 0.44 0.42 0.40 0.38 0.36 20 0.34 10 0.32 NOISE FLOOR (dBm/Hz) 0.30 400 12488-035 0 –163 –162 –161 –160 –159 –158 –157 –156 –155 –154 –153 Figure 35. Noise Floor Cumulative Distribution at Various LO Frequencies Using Internal LO; I/Q Input with 2.68 V DC Bias and RF Output = −10 dBm 900 1400 1900 12488-038 70 2400 LO FREQUENCY (MHz) Figure 38. Supply Current vs. LO Frequency and Temperature (PLL and I/Q Modulator Enabled, LO Buffer Disabled) 0 20 15 –5 5 0 –5 –10 –15 –20 –10 –25 –15 0.5 1.0 1.5 2.0 2.5 3.0 TIME (ms) 3.5 4.0 4.5 5.0 –30 0.35 12488-036 0 Figure 36. Frequency Deviation from LO Frequency at LO = 1.91 GHz to 1.9 GHz vs. Lock Time BAL_CIN = 0, BAL_COUT = 0 BAL_CIN = 1, BAL_COUT = 0 BAL_CIN = 2, BAL_COUT = 0 BAL_CIN = 3, BAL_COUT = 0 BAL_CIN = 4, BAL_COUT = 0 BAL_CIN = 8, BAL_COUT = 0 BAL_CIN = 9, BAL_COUT = 0 BAL_CIN = 10, BAL_COUT = 0 BAL_CIN = 11, BAL_COUT = 0 BAL_CIN = 12, BAL_COUT = 0 BAL_CIN = 13, BAL_COUT = 0 BAL_CIN = 14, BAL_COUT = 0 BAL_CIN = 15, BAL_COUT = 0 BAL_CIN = 15, BAL_COUT = 3 BAL_CIN = 15, BAL_COUT = 8 BAL_CIN = 15, BAL_COUT = 11 BAL_CIN = 15, BAL_COUT = 15 0.85 1.35 1.85 LO FREQUENCY (GHz) 2.35 2.85 12488-039 RETURN LOSS (dB) 10 –20 2400 0.46 SUPPLY CURRENT (A) 80 1900 Figure 37. LO Output Power vs. LO Frequency at Various LO_DRV_LVL Settings 0.50 450 940 1900 2140 2300 2600 90 1400 LO FREQUENCY (MHz) Figure 34. Noise Floor Cumulative Distribution at Various LO Frequencies Using Internal LO; I/Q Input with 2.68 V DC Bias and No RF Output 100 900 12488-037 –7 0 –163 –162 –161 –160 –159 –158 –157 –156 –155 –154 –153 CUMMULATIVE PERCENTAGE (%) LO_DRV_LVL = 2 3 10 FREQUENCY DEVIATION (MHz) TA = –40°C TA = +25°C TA = +85°C 4 LO OUTPUT POWER (dBm) CUMMULATIVE PERCENTAGE (%) 90 Figure 39. RF Output Return Loss vs. LO Frequency (fLO) for Multiple BAL_CIN and BAL_COUT Combinations Rev. B | Page 16 of 43 ADRF6720-27 0 –5 –5 RETURN LOSS (dB) 0 –10 –15 –15 1.3 2.3 3.3 4.3 5.3 LO FREQUENCY (GHz) 6.3 Figure 40. LO Input Return Loss vs. LO Frequency (fLO) –25 0.3 1.3 2.3 3.3 4.3 5.3 LO FREQUENCY (GHz) Figure 41. LO Output Return Loss vs. LO Frequency (fLO) Rev. B | Page 17 of 43 6.3 12488-041 –25 0.3 –10 –20 –20 12488-040 RETURN LOSS (dB) Data Sheet ADRF6720-27 Data Sheet THEORY OF OPERATION Internal LO Mode The ADRF6720-27 integrates a high performance broadband I/Q modulator with a fractional-N PLL and low noise multicore VCOs. The baseband inputs mix with the LO generated internally or provided externally, and convert it to a singleended RF using an integrated RF balun. A block diagram of the device is shown in Figure 1. The ADRF6720-27 is programmed via an SPI. For internal LO mode, the ADRF6720-27 uses the on-chip PLL and VCO to synthesize the frequency of the LO signal. The PLL, shown in Figure 42, consists of a reference path, phase and frequency detector (PFD), charge pump, and a programmable integer divider with prescaler. The reference path takes in a reference clock and divides it down by a factor of 2, 4, or 8, or multiplies it by a factor of 1 or 2, and then passes it to the PFD. The PFD compares this signal to the divided down signal from the VCO. Depending on the PFD polarity selected, the PFD sends either an up or down signal to the charge pump if the VCO signal is either slow or fast compared to the reference frequency. The charge pump sends a current pulse to the offchip loop filter to increase or decrease the tuning voltage (VTUNE). LO GENERATION BLOCK The ADRF6720-27 supports the use of both internal and external LO signals for the mixers. The internal LO is generated by an on-chip VCO, which is tunable over an octave frequency range of 2850 MHz to 5710 MHz. The output of the VCO is phase-locked to an external reference clock through a fractional-N PLL that is programmable through the SPI control registers. To produce in-phase and quadrature phase LO signals over the 356.25 MHz to 2855 MHz frequency range to drive the mixers, steer the VCO outputs through a combination of frequency dividers, as shown in Figure 42. The ADRF6720-27 integrates four VCO cores, covering an octave range of 2850 MHz to 5710 MHz. Table 6 lists the frequency range covered by each VCO. The desired VCO can be selected by addressing the VCO_SEL bits at Register 0x22[2:0]. Alternatively, an external signal can be used with the dividers or a polyphase phase splitter to generate the LO signals in quadrature to the mixers. In demanding applications that require the lowest possible phase noise performance, it may be necessary to source the LO signal externally. The different methods of quadrature LO generation and the control register programming needed are listed in Table 6. The LO source and quadrature generation path can be selected by setting the QUAD_DIV_EN bit (Register 0x01[9]) and the LO_1XVCO_EN bit (Register 0x01[11]). The mode of the VCO signal through a polyphase filter is intended to extend the operating frequency with an internal VCO and is only useful for baseband input frequencies high enough to prevent the RF output from pulling the VCO. POLYPHASE FILTER LOIN+ 34 REF_SEL REG 0x21[2:0] ÷8 ÷4 REFIN 39 LOIN– 33 PFD + ×1 CHARGE PUMP CP VTUNE 36 32 LPF CP_CTL REG 0x20[14:0] ×2 ÷1, ÷2, ÷4 QUAD DIVIDER EXTERNAL LOOP FILTER PFD_POLARITY REG 0x21[3] ÷2 LO_1XVCO_EN REG 0x01[11] QUAD_DIV_EN REG 0x01[9] LO_I+ LO_I– LO_Q+ LO_Q– TO MIXER DIV8 _EN/ DIV4_EN REG 0x22[4:3] N = INT + FRAC MOD ÷1,÷2 ÷2 DRVDIV2_EN REG 0x22[5] LOOUT+ LOOUT– MUXOUT 1 DIV_MODE: REG 0x02[11] INT_DIV: REG 0x02[10:0] FRAC_DIV: REG 0x03[15:0] MOD_DIV: REG 0x04[15:0] VCO_SEL REG 0x22[2:0] REF_MUX_SEL REG 0x21[6:4] Figure 42. LO Block Diagram Rev. B | Page 18 of 43 LO_DRV2X_EN REG 0x01[8] LO_DRV1X_EN REG 0x01[7] 12488-042 LOCK_DET VPTAT Data Sheet ADRF6720-27 Table 6. LO Mode Selection LO Selection Internal (VCO) fVCO or fEXT (MHz) 2850 to 3500 3500 to 4020 4020 to 4600 4600 to 5710 2855 to 3000 700 to 6000 700 to 3000 External 1 Quadrature Generation Divide by 2 Divide by 2 Divide by 2 Divide by 2 Polyphase Divide by 2 Polyphase QUAD_DIV_EN (Register 0x01[9]) 1 1 1 1 0 1 0 LO_1XVCO_EN (Register 0x1[11]) 0 0 0 0 1 0 0 Enables (Register 0x01[6:0]) 111 111X1 111 111X1 111 111X1 111 111X1 111 111X1 101 000X1 000 000X1 VCO_SEL (Register 0x22[2:0]) 011 010 001 000 011 1XX1 XXX1 X = don’t care. LO Frequency and Dividers The signal coming from the VCO or the external LO inputs goes through a series of dividers before it is buffered to drive the active mixers. Two programmable divide by 2 stages divide the frequency of the incoming signal by 1, 2, or 4 before reaching the quadrature divider that further divides the signal frequency by 2 to generate the in-phase and quadrature phase LO signals for the mixers. The control bits (Register 0x22[4:3]) needed to select the different LO frequency ranges are listed in Table 7. Table 7. LO Frequency and Dividers LO Frequency Range (MHz) 1425 to 2855 712.5 to 1425 356.25 to 712.5 fVCO/fLO or fEXT LO/fLO 2 4 8 DIV8_EN (Register 0x22[4]) 0 0 1 DIV4_EN (Register 0x22[3]) 0 1 1 The N divider with divide by 2 divides down the VCO signal to the PFD frequency. The N divider can be configured for fractional or integer mode by addressing the DIV_MODE bit (Register 0x02[11]). The default configuration is set for fractional mode. Use the following equations to determine the N value and PLL frequency: f VCO 2× N N = INT + f LO = Loop Filter The loop filter is connected between the CP and VTUNE pins. The recommended components for 20 kHz filter designs are shown in Table 8 and referenced in Figure 44. The ADRF6720-27 closed-loop phase noise is characterized using a 20 kHz loop filter. Operation with an external VCO is possible. In this case, the output of the loop filter is connected to the tuning pin of the external VCO. The output of the VCO is brought back into the device on the LOIN+ and LOIN− pins. For assistance in designing loop filters with other characteristics, download the most recent revision of ADIsimPLL™ from www.analog.com/adisimpll. Table 8. Recommended Loop Filter Components PLL Frequency Programming f PFD = LO_DIVIDER is the final frequency divider ratio that divides the frequency of the VCO or the external LO signal down by 2, 4, or 8 before it reaches the mixer, as shown in Table 7. Component C57 R12 C58 R23 C59 R26 C60 20 kHz Loop Filter 2700 pF 300 Ω 100 nF 5.6 Ω 2700 pF 820 Ω 1500 pF PLL Lock Time It takes time to lock the PLL after the last register is written. VCO band calibration time and loop settling time are used to determine the PLL lock time. FRAC MOD f ×2×N fvco = PFD LO _ DIVIDER LO_DIVIDER where: fPFD is the phase frequency detector frequency. fVCO is the VCO frequency. N is the fractional divide ratio (INT + FRAC/MOD). INT is the integer divide ratio programmed in Register 0x02. FRAC is the fractional divider programmed in Register 0x03. MOD is the modulus divide ratio programmed in Register 0x04. fLO is the LO frequency going to the mixer core when the loop is locked. After writing to the last register, the PLL automatically performs a VCO band calibration to choose the correct VCO band. This calibration takes approximately 94,208 PFD cycles. For a 40 MHz fPFD, this corresponds to 2.36 ms. After a band calibration completes, the feedback action of the PLL results in the VCO locking to the correct frequency. The speed to be locked depends on the nonlinear cycle slipping behavior, as well as the small signal settling of the loop. For an accurate estimation of the lock time, download the ADIsimPLL tool to capture these effects correctly. In general, higher bandwidth loops tend to lock more quickly than lower bandwidth loops. Rev. B | Page 19 of 43 ADRF6720-27 Data Sheet The lock detect signal is available as one of the selectable outputs through the MUXOUT pin, with a logic high signifying that the loop is locked. The control bits for the MUXOUT pin are the REF_MUX_SEL bits (Register 0x21[6:4]), and the default configuration is for PLL lock detect. Table 10. LO Polarity Setting Address 0x32[11:10] Bit Name POL_Q 01 Required PLL/VCO Settings and Register Write Sequence In addition to writing to the necessary registers to configure the PLL and VCO for the desired LO frequency and phase noise performance, the registers listed in Table 9 are the required registers to write. To ensure that the PLL locks to the desired frequency, follow the proper write sequence of the PLL registers. Configure the PLL registers accordingly to achieve the desired frequency, and the last writes must be to Register 0x02 (INT_DIV), Register 0x03 (FRAC_DIV), or Register 0x04 (MOD_DIV). When Register 0x02, Register 0x03, and Register 0x04 are programmed, an internal VCO calibration initiates, which is the last step to locking the PLL. Table 9. Required PLL/VCO Register Writes Address 0x21[3] 0x49[13:0] Bit Name PFD_POLARITY SET_1[13:9], SET_0[8:0] Setting 0x01 0x14B4 Description Negative polarity Internal settings External LO Mode Use the VCO_SEL bits (Register 0x22[2:0]) to select external or internal LO mode. To configure for external LO mode, set Register 0x22[2:0] to 4 decimal and apply the differential LO signals to Pin 33 (LOIN−) and Pin 34 (LOIN+). The external LO frequency range is 700 MHz to 3 GHz. When the polyphase phase splitter is selected, a 1 × LO signal is required for the active mixer, or a 2 × LO can be used with the internal quadrature divider, as shown in Table 6. There is also the option of using an external VCO with the internal PLL. In this case, the PLL is enabled, but the VCO blocks are turned off. The LOIN+ and LOIN− input pins must be ac-coupled. When not in use, leave the LOIN+ and LOIN− pins unconnected. LO Polarity The ADRF6720-27 offers the flexibility of specifying the quadrature polarity on LO to the I channel or Q channel mixers. This specification determines whether the LO is injected above or below the RF frequency. RF frequency can place either above or below the LO depending on the Register 0x32[11:8] setting as well as the phase relationship between the baseband I and Q. For normal operation and characterization, the Register 0x32 settings are 2 decimal for POL_I (Register 0x32[9:8]) and 1 decimal for POL_Q (Register 0x32, Bits[11:10]). Setting Register 0x32 as such places the RF frequency below the LO (fRF < fLO) when Q leads I and places the RF frequency above the LO (fRF > fLO) when I leads Q. Settings 10 0x32[9:8] POL_I 01 10 Description Quadrature polarity switch, Q channel Inverted Q channel polarity Normal polarity Quadrature polarity switch, I channel. Normal polarity Inverted I channel polarity LO Outputs The ADRF6720-27 can provide either a differential 1 × or 2 × LO output signal at the LOOUT+ and LOOUT− pins (Pin 18 and Pin 19, respectively). The availability of the LO signal makes it possible to daisy-chain many devices. One ADRF6720-27 device can serve as the master where the LO signal is sourced, and the subsequent slave devices can share the same LO output signal from the master. When the quadrature LO signals are generated using the quadrature divider, the output signal is available at either 2× or 1× the frequency of the LO signal at the mixer by setting LO_DRV2X_EN bit (Register 0x1[8]) and DRVDIV2_EN bit (Register 0x22[5]). However, 1× the frequency of the LO signal in this case has a phase ambiguity of 180° relative to the LO signal that drives the mixer core. Because of this phase ambiguity, the utility of this 1 × LO output signal as a system daisy-chained LO signal is compromised. To avoid this ambiguity, a second 1× the frequency of the LO signal output is made available after the quadrature divider. This second 1 × LO output path is enabled by setting the LO_DRV1X_EN bit (Register 0x01[7]) high. When the quadrature LO signals are generated using the polyphase phase splitter, the output signal is also available at 1× the frequency of the LO signal by setting LO_DRV1X_EN bit (Register 0x10[7]) high. Set the output to different drive levels by accessing the LO_DRV_LVL bits (Register 0x22[7:6]), as shown in Table 11. Table 11. LO Output Level at 2140 MHz LO_DRV_LVL (Register 0x22[7:6]) 00 01 10 Rev. B | Page 20 of 43 Amplitude (dBm) −5.8 −1.0 2.2 Data Sheet ADRF6720-27 BASEBAND The baseband inputs are designed to work with a 2.68 V common-mode voltage. To match the 100 Ω impedance of the DAC, place a shunt 100 Ω external resistor across the I and Q inputs. The voltages applied to the differential baseband inputs (I+, I−, Q+, and Q−) drive the V-to-I stage that converts baseband voltages into currents. The converted modulated signal current feeds the modulator mixer core. A programmable dc current can be added to both the I and Q channels to null any carrier feedthrough at the RF output. Refer to the Carrier Feedthrough Nulling section for more information The linearity can be optimized by adding the amplitude and phase correction signals to the current output via the MOD_RSEL (Register 0x31[12:6]) and MOD_CSEL (Register 0x31[5:0]) adjustment. Refer to the Linearity section for more information. ACTIVE MIXERS The ADRF6720-27 has two double balanced mixers: one for the in-phase channel (I channel) and the other for the quadrature channel (Q channel). They upconvert the modulated baseband signal currents by the LO signals to the RF. Tunable RFOUT Balun The ADRF6720-27 integrates a programmable balun operating over a frequency range from 700 MHz to 3000 MHz. It offers single-ended-to-differential conversion and provides additional common-mode noise rejection. The capacitors at the input and output of the balun in parallel with the inductive windings of the balun change the resonant frequency of the inductor capacitor (LC) tank. Therefore, selecting the proper combination of BAL_CIN (Register 0x30[3:0]) and BAL_COUT (Register 0x30[7:4]) sets the desired frequency and optimizes gain. Under most circumstances, it is suggested to set BAL_CIN and BAL_COUT over the frequency profile given in Table 12. However, for matching reasons, it is advantageous to tune the registers independently. BAL_COUT REG 0x30[7:4] BAL_CIN 0 1 2 3 4 8 9 10 11 12 13 14 15 15 15 15 15 BAL_COUT 0 0 0 0 0 0 0 0 0 0 0 0 0 3 8 11 15 Frequency Range (MHz) fRF > 1730 1550 < fRF < 1730 1380 < fRF < 1550 1250 < fRF < 1380 1170 < fRF < 1250 1100 < fRF < 1170 1020 < fRF < 1100 970 < fRF < 1020 930 < fRF < 970 890 < fRF < 930 840 < fRF < 890 820 < fRF < 840 780 < fRF < 820 730 < fRF < 780 680 < fRF < 730 630 < fRF < 680 fRF < 630 ENBL The ENBL pin quickly enables/disables the RF output. The circuit blocks that are enabled/disabled with the ENBL pin can be programmed by setting the appropriate bits in the enables register (Register 0x01) and the ENBL_MASK register (Register 0x10). When the bits in the enables and the ENBL_MASK register are 1, pulling the ENBL pin low disables and pulling high enables the internal blocks more quickly than possible with an SPI write operation. Table 13. Enable/Disable Settings Register 0x01 Enables Bit1 0 Register 0x10 ENBL_MASK Bit1 X2 ENBL Pin Voltage X2 1 0 X2 1 1 >1.8 V 1 1 <0.5 V 12488-043 RFOUT BAL_CIN REG 0x30[3:0] Table 12. Optimum Balun Setting For Desired Frequency Range Figure 43. Integrated Tunable Balun 1 2 This bit refers to any of the 11 bits in the register. X = don’t care. Rev. B | Page 21 of 43 State Block controlled by Register 0x01 enables bit [A] disabled. No effect by ENBL. Block controlled by Register 0x01 enables bit [A] enabled. No effect by ENBL. Block controlled by Register 0x01 enables bit [A] enabled. Block controlled by Register 0x01 enables bit [A] disabled ADRF6720-27 Data Sheet SERIAL PORT INTERFACE The SPI of the ADRF6720-27 allows the user to configure the device for specific functions or operations via a 3-pin SPI port. This interface provides users with added flexibility and customization. The SPI consists of three control lines: SCLK, SDIO, and CS. The timing requirements for the SPI port are shown in Table 2. The ADRF6720-27 protocol consists of seven register address bits, followed by a read/write and 16 data bits. Both the address and data fields are organized with the most significant bit (MSB) first, and end with the least significant bit (LSB). On a write cycle, up to 16 bits of serial write data are shifted in, MSB to LSB. If the rising edge of CS occurs before the LSB of the serial data is latched, only the bits that were latched are written to the device. If more than 16 data bits are shifted in, the 16 most recent bits are written to the device. The ADRF6720-27 input logic level for the write cycle supports an interface as low as 1.4 V. On a read cycle, up to 16 bits of serial read data are shifted out, MSB first. Data shifted out beyond 16 bits is undefined. Readback content at a given register address does not necessarily correspond with the write data of the same address. The output logic level for a read cycle is 2.3 V. Rev. B | Page 22 of 43 Data Sheet ADRF6720-27 BASIC CONNECTIONS FOR OPERATION +3.3V RED 10µF (0805) VPOS8 40 I+ I+ 100Ω (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 0.1µF (0402) 100pF (0402) 100pF (0402) 100pF (0402) 100pF (0402) 100pF (0402) 100pF (0402) 100pF (0402) 100pF (0402) VPOS5 VPOS4 VPOS3 VPOS2 VPOS1 VPOS7 VPOS6 35 30 26 22 3 ADRF6720-27 V TO I I– I– 4 S1 49.9Ω (0402) 24 LO NULLING DAC RFOUT PHASE CORRECTION 8 100Ω (0402) 27 ENBL PHASE CORRECTION LO NULLING DAC Q– Q– 10kΩ (0402) 6 11 17 3.3V V TO I Q+ Q+ LOOUT+ 9 LOOUT 18 LOCK_DET VPTAT 19 LOOUT– ÷2 0Ω (0402) 15 0° POLYPHASE FILTER 90° SERIAL PORT INTERFACE 14 13 REFIN REF_IN 100pF (0402) ÷1, ÷2, ÷4 ÷8 ÷4 ÷2 ×1 REFIN 39 49.9Ω (0402) PFD FRAC N = INT + MOD 4 1 6 100pF (0402) MUXOUT 1 3 100pF (0402) LDO 2.5V 31 CS SCLK CS SCLK SDIO SDIO DECL3 ÷2 100pF (0402) 0.1µF (0402) 10µF (0603) 100pF (0402) 0.1µF (0402) 10µF (0603) 100pF (0402) 0.1µF (0402) 10µF (0603) DECL2 28 ×2 LDO VCO CHARGE PUMP NIC 21 DECL1 12 2 5 7 10 16 20 23 25 29 37 38 36 32 CP R23 5.6Ω (0402) GND R12 300Ω (0402) C58 100nF (0603) C59 2700pF (0402) 100pF (0402) C60 1500pF (0402) 3 4 1 6 EXT LO 100pF (0402) 12488-044 C57 2700pF (0402) 33 34 VTUNE R26 820Ω (0402) NOTES 1. NIC = NO INTERNAL CONNECTION. Figure 44. Basic Connections for Operation (Loop Filter Set to 20 kHz) Figure 44 shows the basic connections for operating the ADRF6720-27 as they are implemented on the evaluation board of the device. POWER SUPPLY AND GROUNDING Connect the power supply pins to a 3.3 V source; the pins can range between 3.15 V and 3.45 V. Individually decouple the pins using 100 pF and 0.1 µF capacitors located as close as possible to the pins. Individually decouple the three internal decoupling nodes (labeled DECL3, DECL2, and DECL1) with capacitors as shown in Figure 44. Tie the 11 GND pins to the same ground plane through low impedance paths. Solder the exposed pad on the underside of the package to a ground plane with low thermal and electrical impedance. If the ground plane spans multiple layers on the circuit board, stitch them together under the exposed pad. The AN-772 Application Note discusses the thermal and electrical grounding of the LFCSP package in detail. Rev. B | Page 23 of 43 ADRF6720-27 Data Sheet BASEBAND INPUTS Drive the four I and Q inputs with an external bias level of 2.68 V. These inputs are generally dc-coupled to the outputs of a dual DAC. The nominal drive level used in the characterization of the ADRF6720-27 is 1 V p-p differential (or 500 mV p-p on each pin). LO INPUT The external LO input is designed to be driven differentially. AC couple both sides of the differential LO source through a pair of series capacitors to the LOIN+ and LOIN− pins. The typical LO drive level, used for the characterization of the ADRF6720-27, is 0 dBm. Apply the reference frequency for the PLL (between 5.7 MHz and 320 MHz) to the REFIN pin, which is ac-coupled. If the REFIN pin is being driven from a 50 Ω source, terminate the pin with 50 Ω as shown in Figure 44. Apply a drive level of about 4 dBm to 14 dBm; 4 dBm is used at characterization. LOOP FILTER The loop filter in Figure 44 is connected between the CP and VTUNE pins. The recommended components for 20 kHz filter designs are shown in Table 8. RF OUTPUT The RF output is available at the RFOUT pin (Pin 24), which can drive a 50 Ω load. Rev. B | Page 24 of 43 Data Sheet ADRF6720-27 APPLICATIONS INFORMATION 3 IOUT0+ RBI– 50Ω IOUT0– 8 IOUT1– RBQ+ 50Ω 3.3V RBQ– 50Ω I– Q– RLQ 100Ω 9 Q+ Adjust the voltage swing for a given DAC output current by placing a different resistance value on RLI and RLQ to the interface (see Figure 45). This adjustment has the effect of varying the ac swing without changing the dc bias already established by the 50 Ω resistors. A higher resistance value increases the output power of the ADRF6720-27 and signal-to-noise ratio (SNR) at the cost of higher intermodulation distortion. Figure 46 shows the relationship between the swing-limiting resistor and the peak-to-peak ac swing that it produces when 50 Ω bias-setting resistors are used. The differential peak-topeak swing at the modulator input is [2 × R [2 × R ] +R ] B × RL B L 0.8 0.6 0.4 10k 12488-046 100 1k AC SWING LIMITING RESISTANCE (Ω) 45 1.2 40 1.1 1.0 CAPACITANCE 30 0.9 25 0.8 20 0.7 15 0.6 10 0.5 5 Figure 45. Interface Between the TxDAC and ADRF6720-27 with 50 Ω Resistors to Ground to Establish the 2.68 V DC Bias for the ADRF6720-27 Baseband Inputs VSIGNAL = I FS × 1.0 35 I+ RLI 100Ω 4 1.2 Figure 46. Relationship Between the AC Swing Limiting Resistance and the Peak-to-Peak Voltage Swing with 50 Ω Bias Setting Resistors RESISTANCE (kΩ) 3.3V 1.4 0 10 12488-045 RBI+ 50Ω 1.6 0.2 ADRF6720-27 TxDAC IOUT1+ 1.8 0 0 0.4 RESISTANCE 100 200 300 CAPACITANCE (pF) An example of interfacing the dual-channel differential current sinking TxDAC is shown in Figure 45. The baseband inputs of the ADRF6720-27 require a dc bias of 2.68 V and the TxDAC outputs interface seamlessly with ADRF6720-27. Place a shunt 100 Ω external resistor across the I and Q inputs to match the 100 Ω impedance of the DAC. With the 50 Ω termination resistors to the power supply in the DAC outputs , the 100 Ω shunt resistors across the I and Q inputs with a 20 mA full-scale current and bleed current , the resulting drive signal from each differential pair is 1 V p-p differential (with the DAC running at 0 dBFS), with a 2.68 V dc bias. 2.0 400 500 600 FREQUENCY (MHz) 700 800 900 0.3 1000 12488-047 The ADRF6720-27 is designed to interface with minimal components to members of the Analog Devices, Inc., family of TxDAC® converters. These dual- or quad-channel differential current sinking DACs provide a current swing from 0 mA to 20 mA. The interface described in this section can be used with any DAC that has a similar output. Figure 47 shows the differential input resistance and capacitance over baseband input frequencies. DIFFERENTIAL SWING (V p-p) DAC TO I/Q MODULATOR INTERFACING Figure 47. Differential Baseband Input Resistance and Input Capacitance Equivalents (Shunt R, Shunt C) I/Q Filtering An antialiasing filter between the DAC and modulator is necessary to filter out Nyquist images, common-mode noise, and broadband DAC noise. The interface for setting up the biasing and ac swing described in the DAC to I/Q Modulator Interfacing section lends itself well to the introduction of such a filter. The filter can be inserted between the dc bias setting resistors and the ac swing limiting resistor. With this configuration, the dc bias setting resistors set the source impedance, and the ac swing limiting resistor sets the load impedance with a high differential I and Q input impedance in parallel for the filter. Rev. B | Page 25 of 43 ADRF6720-27 Data Sheet BASEBAND BANDWIDTH The ADRF6720-27 can be used with a DAC generating a complex IF (CIF), as well as a zero IF signal (ZIF). The 1 dB bandwidth of the ADRF6720-27 is more than 1000 MHz. Figure 48 shows the baseband frequency response of ADRF6720-27, facilitating high CIF and providing sufficient flat bandwidth for digital predistortion (DPD) algorithms. Any flatness variations across frequency at the ADRF6720-27 RF output have been calibrated out of this measurement. 0 –1 12488-049 _ –2 _ –3 Figure 49. Carrier Feedthrough Optimization Through DCOFF_I and DCOFF_Q Adjustment –4 –5 SIDEBAND SUPPRESSION OPTIMIZATION –6 –7 –8 –9 0 200 400 600 800 1000 BB FREQUENCY (MHz) 12488-048 BASEBAND FREQUENCY RESPONSE (dB) 1 Figure 48. ADRF6720-27 Baseband Frequency Response CARRIER FEEDTHROUGH NULLING Carrier feedthrough results from minute dc offsets that occur on the differential baseband inputs. In an I/Q modulator, nonzero differential offsets mix with the LO and result in carrier feedthrough to the RF output. In addition to this effect, some of the signal power at the LO input couples directly to the RF output (this may be as a result of bond wire to bond wire coupling or coupling through the silicon substrate). The net carrier feedthrough at the RF output is the vector combination of the signals that appear at the output as a result of these two effects. Sideband suppression results from gain and phase imperfection between the I and Q channels. Sideband suppression also results from the quadrature error in generating quadrature LO signals. The net unwanted sideband signal at the RF output is the vector combination of the signals as a result of these effects. The ADRF6720-27 offers quadrature phase adjustment through the I_LO (Register 0x32[3:0]) and Q_LO (Register 0x32[7:4]) parameters to reject unwanted sideband signal. Figure 50 shows the level of unwanted sideband signal achievable from the ADRF6720-27 across the I_LO and Q_LO parameters If further optimization is required, the amplitude and phase adjustments can be made externally by a TxDAC. The result of this type of adjustment is shown in Figure 51. The ADRF6720-27 has a feature to add dc current, positive or negative, to both the I and Q channels for carrier feedthrough nulling. Figure 49 shows carrier feedthrough vs. DCOFF_I (Register 0x33[15:8]) and DCOFF_Q (Register 0x33[7:0]). I_LO Q_LO 12488-050 The carrier feedthrough nulling can also be accomplished externally by a TxDAC. Figure 50. Sideband Suppression Optimization Through I_LO and Q_LO Adjustment; LO = 2140 MHz Rev. B | Page 26 of 43 Data Sheet 0 BEFORE NULLING AFTER NULLING BY I_LO AND Q_LO IN ADRF6720–27 AFTER NULLING EXTERNALLY –10 –20 –30 –40 –50 –60 –80 _ _ 1900 2400 LO FREQUENCY (MHz) Figure 53. OIP2 vs. MOD_CSEL and MOD_RSEL at fRF = 2140 MHz, I/Q Amplitude per Tone = 0.3 V p-p Differential Figure 51. Sideband Suppression Before and After Nulling Using I_LO and Q_LO Through External Adjustment; LO = 2140 MHz LINEARITY The linearity in ADRF6720-27 can be optimized through the MOD_RSEL (Register 0x31[12:6]) and MOD_CSEL (Register 0x31[5:0]) settings. The resistance and capacitance curves as a function of the MOD_RSEL and MOD_CSEL settings. These settings control the amount of antiphase distortion to the baseband input stages to correct for distortion. The top two bits (Register 0x31[12:11]) of MOD_RSEL and the MSB (Register 0x31[5]) of MOD_CSEL are used as a range setting. Figure 52 and Figure 53 show the output IP3 and output IP2 that are achievable across the MOD_RSEL and MOD_CSEL settings. _ _ The typical External LO driving level of the ADRF6720-27 is 0 dBm differential. All the baseband inputs must be externally dc biased to 2.68 V. Figure 54 and Figure 55 show the performance variation vs. the external LO amplitude and baseband commonmode voltage, respectively. 70 10 SSB OUTPUT POWER (dBm) 0 OUTPUT IP2 (dBm) 60 50 –10 40 –20 OUTPUT IP3 (dBc) 30 –30 CARRIER FEEDTHROUGH (dBm) 20 –40 SIDEBAND SUPPRESSION(dBc) 10 –50 –60 –70 –10 0 THIRD HARMONIC (dBc) SECOND HARMONIC (dBc) –5 0 5 EXTERNAL LO AMPLITUDE (dBm) –10 10 Figure 54. SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, Sideband Suppression, OIP2, and OIP3 vs. External LO Amplitude; Baseband I/Q Amplitude = 0.6 V p-p Differential for OIP2, and OIP3, 1 V p-p Differential for POUT, Sideband Suppression, HD2, HD3, Carrier Feedthrough, fOUT = 2140 MHz, 25°C 12488-052 Figure 52 and Figure 53 show both a surface and a contour plot in one figure. The contour plot is located directly underneath the surface plot. The peaks on the surface plot indicate the maximum output IP3 and maximum output IP2, and the same color pattern on the contour plot determines the optimized MOD_RSEL and MOD_CSEL values. The overall shape of the output IP3 plot varies with the MOD_RSEL setting more than the MOD_CSEL setting. LO AMPLITUDE AND COMMON-MODE VOLTAGE OUTPUT IP2, OUTPUT IP3 (dBm) 1400 SSB OUTPUT POWER, CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION, SECOND HARMONIC, THIRD HARMONIC (dBc) 900 12488-051 –90 400 12488-053 –70 12488-054 SIDEBAND SUPPRESSION (dBc) ADRF6720-27 Figure 52. OIP3 vs. MOD_CSEL and MOD_RSEL at fRF = 2140 MHz, I/Q Amplitude Per Tone = 0.3 V p-p Differential Rev. B | Page 27 of 43 application by selecting a combination of PLL reference frequency, PFD frequency, and LO frequency in order to ensure that the higher spurious emissions fall out of the band of interest. For more information, contact application support. 70 60 OUTPUT IP2, OUTPUT IP3 (dBm) OUTPUT IP3 (dBm) 30 –30 SIDEBAND SUPPRESSION (dBc) –40 20 CARRIER FEEDTHTOUGH (dBm) 10 –50 SECOND HARMONIC (dBc) 0 –60 –80 2.4 –10 THIRD HARMONIC (dBc) –70 2.5 2.6 2.7 –30 2.8 2.9 –20 3.0 BASEBAND COMMON-MODE VOLTAGE (V) Figure 55. SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, Sideband Suppression, OIP2, and OIP3 vs. Baseband I/Q Amplitude = 0.6 V p-p Differential for OIP2, and OIP3, 1 V p-p Differential for POUT, Sideband Suppression, HD2, HD3, Carrier Feedthrough, fOUT = 2140 MHz, 25°C OPERATING OUT OF FREQUENCY RANGE 10 70 SSB OUTPUT POWER (dBm) 0 60 –10 50 –20 40 OUTPUT IP3 (dBc) –30 20 THIRD HARMONIC (dBc) –60 –70 2800 30 CARRIER FEEDTHROUGH (dBm) SIDEBAND SUPPRESSION (dBc) –40 –50 OUTPUT IP2, OUTPUT IP3 (dBm) OUTPUT IP2 (dBm) 10 SECOND HARMONIC (dBc) 3000 3200 3400 3600 LO FREQUENCY (MHz) 3800 0 –10 4000 12488-056 SSB OUTPUT POWER, CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION, SECOND HARMONIC, THIRD HAMONIC (dBc) The operating frequency range of the ADRF6720-27 can be extended above 3000 MHz using the external 1x LO through the polyphase filter. Above the specified RF frequency range of 3000 MHz, loss from internal balun results in output power drop and output IP2 and IP3 degradation, accordingly. See Figure 56 for a plot of typical SSB output power, second- and third-order harmonics, carrier feedthrough, sideband suppression, OIP2, and OIP3 performance from 3000 MHz to 4000 MHz above operating frequency. Figure 56. Typical SSB Output Power, Second- and Third-Order Harmonics, Carrier Feedthrough, Sideband Suppression, OIP2, and OIP3 Performance Above Operating Frequency; Baseband I/Q Amplitude = 0.6 V p-p Differential for OIP2, and OIP3, 1 V p-p Differential for POUT, Sideband Suppression, HD2, HD3, Carrier Feedthrough, 25°C SPURIOUS PERFORMANCE Figure 57 to Figure 60 show typical spurious emission of the PFD harmonics at the RF output (fLO ± N × fPFD). As shown in Figure 57 to Figure 60, the ADRF6720-27 typically achieves better than −90 dBc/Hz PFD harmonic spurious emissions at most offsets. If required, the spurious emission profile shown in Figure 57 to Figure 60 can be tailored to each individual TA = –40°C TA = +25°C TA = +85°C –40 –50 –60 –70 –80 N=8 –90 –100 N=1 N = 20 –110 –120 LO –130 700 750 800 850 900 950 FREQUENCY (MHz) 1000 1050 12488-060 40 –20 Figure 57. PFD Spurious Emissions on Modulator Output, fLO − N × fPFD; fLO = 1036.8 MHz, RFOUT ≈ 4 dBm at 25°C, fREF = 61.44 MHz at 4 dBm, fPFD = 15.36 MHz, Integer PLL Mode –30 TA = –40°C TA = +25°C TA = +85°C –40 –50 –60 –70 –80 N=8 –90 –100 N = 20 N=1 –110 –120 LO –130 800 850 900 950 1000 1050 FREQUENCY (MHz) 1100 1150 12488-061 50 Figure 58. PFD Spurious Emissions on Modulator Output, fLO − N × fPFD; fLO = 1128.96 MHz, RFOUT ≈ 4 dBm at 25°C, fREF = 61.44 MHz at 4 dBm, fPFD = 15.36 MHz, Integer PLL Mode –30 TA = –40°C TA = +25°C TA = +85°C –40 –50 –60 –70 N=8 –80 –90 N=1 N = 20 –100 –110 –120 LO –130 1650 1700 1750 1800 1850 1900 FREQUENCY (MHz) 1950 2000 12488-062 OUTPUT IP2 (dBm) –10 fLO – N × fPFD SPURIOUS LEVEL (dBc) 0 fLO – N × fPFD SPURIOUS LEVEL (dBc) SSB OUTPUT POWER (dBm) LO + N × PFD SPURIOUS LEVEL (dBc) 10 Data Sheet 12488-055 SSB OUTPUT POWER, CARRIER FEEDTHROUGH (dBm), SIDEBAND SUPPRESSION, SECOND HARMONIC, THIRD HARMONIC (dBc) ADRF6720-27 Figure 59. PFD Spurious Emissions on Modulator Output, fLO + N × fPFD; fLO = 1658.88 MHz, RFOUT ≈ 4 dBm at 25°C, fREF = 61.44 MHz at 4 dBm, fPFD = 15.36 MHz, Integer PLL Mode Rev. B | Page 28 of 43 Data Sheet ADRF6720-27 LO + N × PFD SPURIOUS LEVEL (dBc) –30 TA = –40°C TA = +25°C TA = +85°C –40 –50 –60 –70 N=8 –80 –90 N = 20 N=1 –100 –110 –120 1850 1900 1950 2000 FREQUENCY (MHz) 2050 2100 2150 Figure 60. PFD Spurious Emissions on Modulator Output, fLO + N × fPFD; fLO = 1781.76 MHz, RFOUT ≈ 4 dBm at 25°C, fREF = 61.44 MHz at 4 dBm, fPFD = 15.36 MHz, Integer PLL Mode 12488-057 1800 12488-063 LO –130 1750 Figure 61. Evaluation Board Layout for the ADRF6720-27 Package LAYOUT Solder the exposed pad on the underside of the ADRF6720-27 to a low thermal and electrical impedance ground plane. This pad is typically soldered to an exposed opening in the solder mask on the evaluation board. Notice the use of 25 via holes on the exposed pad of the ADRF6720-27 evaluation board. Connect these ground vias to all other ground layers on the evaluation board to maximize heat dissipation from the device package. Rev. B | Page 29 of 43 ADRF6720-27 Data Sheet CHARACTERIZATION SETUPS The primary setup used to characterize the ADRF6720-27 is shown in Figure 62. This setup was used to evaluate the product as a single-sideband modulator. An automated software program (VEE) was used to control equipment over the IEEE bus. The setup was used to measure SSB, OIP2, OIP3, output P1 dB (OP1dB), LO, and sideband suppression null. For phase noise and reference spur measurements, see the phase noise setup shown in Figure 63. Phase noise was measured on an LO and modulator output. ADRF6720-27 TEST RACK ASSEMBLY (INTERNAL VCO CONFIGURATION) ALL INSTRUMENTS ARE CONNECTED IN DAISY-CHAIN FASHION VIA GBIP CABLE UNLESS OTHERWISE NOTED. E3631A POWER SUPPLY (+6V ADJUSTED TO 5V) +3.3V FOR VPOS TO 34950 MODULE 34401A DMM (FOR SUPPLY CURRENT MEASUREMENT) 34980A WITH 34950 AND (×3) 34921 MODULES PROGRAMMING AND DC CABLE (×4 FOR MULTISITE) INPUT (RFOUT) AGILENT MXA N9020A SPECTRUM ANALYZER 20-PIN CONNECTOR DC HEADER 12-PIN CONNECTOR (REGISTER PROGRAMMING) REFIN KEITHLEY S46 SWITCH SYSTEM (FOR RFOUT AND REFIN ON 4 SITES) ADRF6720-27 RFOUT OUTPUT (REF) KEITHLEY S46 SWITCH SYSTEM (FOR BASEBAND INPUTS ON 4 SITES) EVALUATION BOARD 6dB ROHDE & SCHWARZ SMT 06 SIGNAL GENERATOR (REFIN) BASEBAND INPUTS AT 1MHz PC CONTROL CONNECTED TO SYSTEM VIA USB TO GPIB ADAPTER Figure 62. General Characterization Setup Rev. B | Page 30 of 43 12488-058 BASEB AND OUTPUTS (I–, I+, Q–, Q+) AEROFLEX IFR 3416 FREQUENCY GENERATOR (WITH BASEBAND OUTPUTS AT 1MHz) Data Sheet ADRF6720-27 ADRF6720-27 PHASE NOISE STAND SETUP ALL INSTRUMENTS ARE CONNECTED IN DAISY-CHAIN FASHION VIA GBIP CABLE UNLESS OTHERWISE NOTED. ROHDE & SCHWARZ SMA 100A SIGNAL GENERATOR REFIN AGILENT E5052A SIGNAL SOURCE ANALYZER AGILENT MXA N9020A SPECTRUM ANALYZER IF OUT KEITHLEY S46 SWITCH SYSTEM 2 (FOR RFOUT AND REFIN ON 4 SITES) LOOUT± REFIN BASEBAND INPUTS (I–, I+, Q–, Q+) 20-PIN CONNECTOR (DC MEASUREMENT, +3.3V POS) AND 12-PIN CONNECTOR (VCO AND PLL PROGRAMMING) 3dB KEITHLEY S46 SWITCH SYSTEM 1 (FOR BASEBAND INPUTS ON 4 SITES) 6dB IFR 3416 SIGNAL GENERATOR (BASEBAND SOURCE) ADRF6720-27 EVALUATION BOARD 34980A MULTIFUNCTION SWITCH (WITH 34950 AND 34921 MODULES) INPUT DC AGILENT 34401A DMM (IN DC I MODE, SUPPLY CURRENT MEASUREMENT) PC CONTROL CONNECTED TO SYSTEM VIA USB TO GPIB ADAPTER Figure 63. Characterization Setup for Phase Noise and Reference Spur Measurements Rev. B | Page 31 of 43 12488-059 AGILENT E3631A POWER SUPPLY ADRF6720-27 Data Sheet REGISTER MAP Table 14. ADRF6720-27 Register Map Bit 15 Reg Name Bits Bit 7 0x00 SOFT_RESET [15:8] Bit 14 Bit 6 Bit 13 Bit 5 Bit 12 Bit 4 [7:0] 0x01 ENABLES 0x02 0x03 0x04 INT_DIV FRAC_DIV MOD_DIV RESERVED LO_DRV1X_EN VCO_MUX_EN [15:8] REF_BUF_EN RESERVED PFD_CTL VCO_CTL BALUN_CTL [15:8] MOD_DIV[15:8] [7:0] MOD_DIV[7:0] RESERVED CP_SEL MOD_CTL1 DITH_CTL1 0x45 DITH_CTL2 VCO_CTL2 VCO_CTL3 DIV8_EN 0x2A03 RW VCO_SEL RESERVED 0x0000 RW BAL_CIN RESERVED MOD_RSEL[6:2] MOD_RSEL[1:0] 0x1101 RW MOD_CSEL RESERVED MOD_BLEED POL_Q Q_LO POL_I 0x0900 RW I_LO DCOFF_I [7:0] DCOFF_Q 0x0000 RW RESERVED RESERVED ABLDLY 0x0010 RW CP_CTRL [15:8] PFD_CLK_EDGE RESERVED RESERVED 0x000E RW DITH_EN [15:8] DITH_VAL[15:8] [7:0] DITH_VAL[7:0] [15:8] [7:0] REF_SEL DIV4_EN [15:8] [15:8] 0x0C26 RW VCO_LDO_R2SEL DRVDIV2_EN RESERVED DITH_MAG DITH_VAL 0x0000 RW VTUNE_CTRL [7:0] VCO_BAND_SRC 0x49 RESERVED 0x000B RW PFD_POLARITY BAL_COUT [7:0] 0x43 VCO_LDO_MASK RESERVED VCO_LDO_R4SEL LO_DRV_LVL [15:8] [7:0] CP_MASK RESERVED 0x40 PFD_CP_CTL [15:8] 0x42 DIV_MASK CP_CSCALE REF_MUX_SEL [7:0] 0x33 0x0600 RW CP_BLEED RESERVED [15:8] [15:8] 0x002C RW LO_1XVCO_MASK MOD_MASK QUAD_DIV_MASK LO_DRV2X_MASK 0xF67F RW [15:8] [7:0] INT_DIV[10:8] 0xF67F RW 0x0128 RW RESERVED 0x31 MOD_LIN_CTL [15:8] MOD_CTL0 RESERVED FRAC_DIV[7:0] [7:0] 0x32 VCO_LDO_EN FRAC_DIV[15:8] [7:0] 0x30 CP_EN [7:0] [7:0] 0x22 DIV_EN [15:8] [7:0] 0x21 LO_DRV2X_EN DIV_MODE RESERVED Reset RW 0x0000 W SOFT_RESET QUAD_DIV_EN INT_DIV[7:0] [15:8] Bit 8 Bit 0 MOD_EN VCO_EN [7:0] LO_DRV1X_MASK VCO_MUX_MASK REF_BUF_MASK VCO_MASK CP_CTL Bit 9 Bit 1 LO_1XVCO_EN [7:0] 0x10 ENBL_MASK [15:8] 0x20 Bit 10 Bit 2 RESERVED [15:8] [7:0] Bit 11 Bit 3 RESERVED 0x0000 RW BAND RESERVED SET_1 SET_0[7:0] Rev. B | Page 32 of 43 SET_0[8] 0x16BD RW Data Sheet ADRF6720-27 REGISTER DETAILS Address: 0x00, Reset: 0x0000, Name: SOFT_RESET Table 15. Bit Descriptions for SOFT_RESET Bits 0 Bit Name SOFT_RESET Settings Description Soft Reset. Reset 0x0 Access W Reset 0x0 0x1 0x1 0x0 0x0 0x1 0x1 0x1 0x1 0x1 0x1 Access RW RW RW RW RW RW RW RW RW RW RW Address: 0x01, Reset: 0xF67F, Name: ENABLES Table 16. Bit Descriptions for ENABLES Bits 11 10 9 8 7 6 5 4 3 2 1 Bit Name LO_1XVCO_EN MOD_EN QUAD_DIV_EN LO_DRV2X_EN LO_DRV1X_EN VCO_MUX_EN REF_BUF_EN VCO_EN DIV_EN CP_EN VCO_LDO_EN Settings Description Enables 1 × LO with Internal VCO. Enables MOD/LO Drive Chain. Enables Quad Divider for 2 × LO Operation. Enables External 2 × LO Driver—Before Quad Divider. Enables External 1 × LO Driver—After Quad Divider. Enables VCO Mux. Enables Reference Buffer. Enables VCOs. Enables VCO Dividers. Enables Charge Pump. Enables VCO LDO. Rev. B | Page 33 of 43 ADRF6720-27 Data Sheet Address: 0x02, Reset: 0x002C, Name: INT_DIV Table 17. Bit Descriptions for INT_DIV Bits 11 Bit Name DIV_MODE Settings 0 1 [10:0] INT_DIV Description Divide Mode. Fractional Integer Divider INT Value. Reset 0x0 Access RW 0x2C RW Reset 0x128 Access RW Reset 0x600 Access RW Address: 0x03, Reset: 0x0128, Name: FRAC_DIV Table 18. Bit Descriptions for FRAC_DIV Bits [15:0] Bit Name FRAC_DIV Settings Description Divider FRAC Value. Address: 0x04, Reset: 0x0600, Name: MOD_DIV Table 19. Bit Descriptions for MOD_DIV Bits [15:0] Bit Name MOD_DIV Settings Description Divider Modulus Value. Rev. B | Page 34 of 43 Data Sheet ADRF6720-27 Address: 0x10, Reset: 0xF67F, Name: ENBL_MASK Table 20. Bit Descriptions for ENBL_MASK Bits 11 10 9 8 7 6 5 4 3 2 1 Bit Name LO_1XVCO_MASK MOD_MASK QUAD_DIV_MASK LO_DRV2X_MASK LO_DRV1X_MASK VCO_MUX_MASK REF_BUF_MASK VCO_MASK DIV_MASK CP_MASK VCO_LDO_MASK Settings Description Enable 1 × LO with internal VCO. MOD Enable. Quadrature Divide Path Enable (2 ×/4 ×/8 × LO). External 2 × LO Driver Enable—Before Quad Divider. External 1 × LO Driver Enable—After Quad Divider. VCO_Mux_Enable. Reference Buffer Enable. Power Up VCOs. Power Up Dividers. Power Up Charge Pump. Power Up VCO LDO. Address: 0x20, Reset: 0x0C26, Name: CP_CTL Rev. B | Page 35 of 43 Reset 0x0 0x1 0x1 0x0 0x0 0x1 0x1 0x1 0x1 0x1 0x1 Access RW RW RW RW RW RW RW RW RW RW RW ADRF6720-27 Data Sheet Table 21. Bit Descriptions for CP_CTL Bits 14 Bit Name CP_SEL Settings 0 1 [13:10] CP_CSCALE 0001 0011 0111 1111 [5:0] CP_BLEED 000000 000001 000010 000011 … 011111 100000 100001 100010 100011 … 111111 Description Charge Pump Reference Current Select. Internal Charge Pump. External Charge Pump. Charge Pump Coarse Scale Current. 250 µA. 500 µA. 750 µA. 1000 µA. Charge Pump Bleed. 0 µA 15.625 µA Sink. 31.25 µA Sink. 46.875 µA Sink. Reset 0x0 Access RW 0x3 RW 0x26 RW Reset 0x0 Access RW 0x1 RW 484.375 µA Sink. 0 µA. 15.625 µA Source. 31.25 µA Source. 46.875 µA Source. 484.375 µA Source. Address: 0x21, Reset: 0x000B, Name: PFD_CTL Table 22. Bit Descriptions for PFD_CTL Bits [6:4] Bit Name REF_MUX_SEL Settings 000 001 010 011 100 101 110 3 PFD_POLARITY 0 1 Description Reference (REF) Output Mux Select. LOCK_DET. VPTAT. REFCLK. REFCLK/2. REFCLK × 2. REFCLK/8. REFCLK/4. Set PFD Polarity. Positive. Negative. Rev. B | Page 36 of 43 Data Sheet Bits [2:0] Bit Name REF_SEL ADRF6720-27 Settings 000 001 010 011 100 Description Set REF Input Multiply/Divide Ratio. ×2. ×1. Divide by 2. Divide by 4. Divide by 8. Reset 0x3 Access RW Reset 0x2 0xA 0x0 Access RW RW RW 0x0 RW 0x0 RW 0x0 RW Address: 0x22, Reset: 0x2A03, Name: VCO_CTL Table 23. Bit Descriptions for VCO_CTL Bits [15:12] [11:8] [7:6] Bit Name VCO_LDO_R4SEL VCO_LDO_R2SEL LO_DRV_LVL Settings 00 01 10 5 DRVDIV2_EN 0 1 4 DIV8_EN 0 1 3 DIV4_EN 0 1 Description VCO LDO Resistor 4 Selections. VCO LDO Resistor 2 Selections. Set External LO Output Amplitude. −5.8 dBm. −1.0 dBm. +2.2 dBm. Divide by 2 for External LO Driver Enable. Disable. Enable. Divide by 2 in LO Path for Total Division of 8. Disable. Enable. Divide by 2 in LO Path for Total Division of 4. Disable. Enable. Rev. B | Page 37 of 43 ADRF6720-27 Bits [2:0] Bit Name VCO_SEL Data Sheet Settings 000 001 010 011 100 Description Select VCO Core/External LO. 4.6 GHz to About 5.71 GHz. 4.02 GHz to About 4.6 GHz. 3.5 GHz to About 4.02 GHz. 2.85 GHz to About 3.5 GHz. External LO/VCO. Reset 0x3 Access RW Reset 0x0 Access RW 0x0 RW Reset 0x44 0x01 Access RW RW Address: 0x30, Reset: 0x0000, Name: BALUN_CTL Table 24. Bit Descriptions for BALUN_CTL Bits [7:4] Bit Name BAL_COUT Settings 0000 1111 [3:0] BAL_CIN 0000 1111 Description Set Balun Output Capacitance. Minimum Capacitance Value. Maximum Capacitance Value. Set Balun Input Capacitance. Minimum Capacitance Value. Maximum Capacitance Value. Address: 0x31, Reset: 0x1101, Name: MOD_LIN_CTL Table 25. Bit Descriptions for MOD_LIN_CTL Bits [12:6] [5:0] Bit Name MOD_RSEL MOD_CSEL Settings Description Modulator Linearizer RSEL Value. Modulator Linearizer CSEL Value. Rev. B | Page 38 of 43 Data Sheet ADRF6720-27 Address: 0x32, Reset: 0x0900, Name: MOD_CTL0 Table 26. Bit Descriptions for MOD_CTL0 Bits [14:12] [11:10] Bit Name MOD_BLEED POL_Q Settings 01 10 [9:8] POL_I 01 10 [7:4] [3:0] Q_LO I_LO Description Modulator Bleed Current. Quadrature Polarity Switch, Q Channel. Inverted Q Channel Polarity. Normal Polarity. Quadrature Polarity Switch, I Channel. Normal Polarity. Inverted I Channel Polarity. Unwanted Sideband Nulling, Q Channel. Unwanted Sideband Nulling, I Channel. Address: 0x33, Reset: 0x0000, Name: MOD_CTL1 Rev. B | Page 39 of 43 Reset 0x0 0x2 Access RW RW 0x1 RW 0x0 0x0 RW RW ADRF6720-27 Data Sheet Table 27. Bit Descriptions for MOD_CTL1 Bits [15:8] Bit Name DCOFF_I Settings 00000000 00000001 00000010 00000011 … 01111110 01111111 10000000 10000001 10000010 10000011 … 11111110 11111111 [7:0] DCOFF_Q 00000000 00000001 00000010 00000011 … 01111110 01111111 10000000 10000001 10000010 10000011 … 11111110 11111111 Description LO Nulling, I Channel. 0 µA. +5 µA. +10 µA. +15 µA. … +630 µA. +635 µA. 0 µA. −5 µA. −10 µA. −15 µA. … −630 µA. −635 µA. LO Nulling, Q Channel. 0 µA. +5 µA. +10 µA. +15 µA. … +630 µA. +635 µA. 0 µA. −5 µA. −10 µA. −15 µA. … −630 µA. −635 µA. Address: 0x40, Reset: 0x0010, Name: PFD_CP_CTL Rev. B | Page 40 of 43 Reset 0x0 Access RW 0x0 RW Data Sheet ADRF6720-27 Table 28. Bit Descriptions for PFD_CP_CTL Bits [6:5] Bit Name ABLDLY Settings 00 01 10 11 [4:2] CP_CTRL 000 001 010 011 100 [1:0] PFD_CLK_EDGE 00 01 10 11 Description Set Antibacklash Delay. 0 ns. 0.5 ns. 0.75 ns. 0.9 ns. Set Charge Pump Control. Both On. Pump Down. Pump Up. Tristate. PFD. Set PFD Clock Edge Trigger. Divide and Reference Down Edge. Divide Down Edge, Reference Up Edge. Divide Up Edge, Reference Down Edge. Divide and Reference Up Edge. Reset 0x0 Access RW 0x4 RW 0x0 RW Reset 0x1 Access RW 0x3 0x0 RW RW Reset 0x0 Access RW Address: 0x42, Reset: 0x000E, Name: DITH_CTL1 Table 29. Bit Descriptions for DITH_CTL1 Bits 3 Bit Name DITH_EN Settings 0 1 [2:1] 0 DITH_MAG DITH_VAL Description Set Dither Enable. Disable. Enable. Set Dither Magnitude. Set Dither Value. Address: 0x43, Reset: 0x0000, Name: DITH_CTL2 Table 30. Bit Descriptions for DITH_CTL2 Bits [15:0] Bit Name DITH_VAL Settings Description Set Dither Value. Rev. B | Page 41 of 43 ADRF6720-27 Data Sheet Address: 0x45, Reset: 0x0000, Name: VCO_CTL2 Table 31. Bit Descriptions for VCO_CTL2 Bits [9:8] Bit Name VTUNE_CTRL Settings 00 01 7 VCO_BAND_SRC 0 1 [6:0] BAND Description Source for VCO VTUNE Pin. Band Calibration Routine. SPI. VCO Band Source Band Calibration Routine. SPI. VCO Band Selection. Reset 0x0 Access RW 0x0 RW 0x00 RW Reset 0x0B Access RW 0x0BD RW Address: 0x49, Reset: 0x16BD, Name: VCO_CTL3 Table 32. Bit Descriptions for VCO_CTL3 Bits [13:9] Bit Name SET_1 [8:0] SET_0 Settings Description Internal Settings. Refer to the Required PLL/VCO Settings and Register Write Sequence section. Internal Settings. Refer to the Required PLL/VCO Settings and Register Write Sequence section. Rev. B | Page 42 of 43 Data Sheet ADRF6720-27 OUTLINE DIMENSIONS 0.30 0.25 0.18 31 30 0.50 BSC TOP VIEW 0.80 0.75 0.70 0.45 0.40 0.35 1 21 11 20 PIN 1 INDICATOR 4.55 4.40 SQ 4.25 EXPOSED PAD 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 40 10 BOTTOM VIEW 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WJJD. 06-04-2012-A PIN 1 INDICATOR 6.10 6.00 SQ 5.90 Figure 64. 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 6 mm × 6 mm Body, Very Very Thin Quad (CP-40-11) Dimensions shown in millimeters ORDERING GUIDE Model1 ADRF6720-27ACPZ-R7 ADRF6720-27-EVALZ 1 Temperature Range −40°C to +85°C Package Description 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ] Evaluation Board Z = RoHS Compliant Part. ©2014–2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D12488-0-9/15(B) Rev. B | Page 43 of 43 Package Option CP-40-11