Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC620 v01.1007 MIXERS - I/Q MIXERS / IRM - CHIP 3 GaAs MMIC I/Q MIXER 3 - 7 GHz Typical Applications Features The HMC620 is ideal for: Wide IF Bandwidth: DC - 3.5 GHz • Point-to-Point Radios High Image Rejection: 33 dB • Point-to-Multi-Point Radios High LO to RF Isolation: 45 dB • WiMAX & Fixed Wireless High Input IP3: +23 dB • VSAT Die Size: 1.49 x 1.15 x 0.10 mm Functional Diagram General Description The HMC620 is a compact I/Q MMIC mixer which can be used as either an Image Reject Mixer (IRM) or a Single Sideband Upconverter. The chip utilizes two standard Hittite double balanced mixer cells and a 90 degree hybrid fabricated in a GaAs MESFET process. All data shown below is taken with the chip mounted in a 50 Ohm test fixture and includes the effects of 1 mil diameter x 20 mil length bond wires on each port. A low frequency quadrature hybrid was used to produce a 100 MHz upper side band (USB) IF output. This product is a much smaller and more consistent alternative to hybrid style Image Reject Mixers and Single Sideband Upconverter assemblies. Electrical Specifi cations, TA = +25° C, IF= 100 MHz, LO = +15 dBm* Parameter Min. Typ. Frequency Range, RF/LO 3.0 - 7.0 Frequency Range, IF DC - 3.5 Conversion Loss (As IRM) Image Rejection 7.5 25 1 dB Compression (Input) 28 Max. Min. Typ. Max. 4.5 - 6.5 GHz DC - 3.5 8.5 7.5 31 +13 GHz 9 dB 33 dB +13 dBm LO to RF Isolation 35 45 35 45 dB LO to IF Isolation 35 40 35 40 dB dBm IP3 (Input) 23 23 Amplitude Balance 0.1 0.2 dB 3 3 Deg Phase Balance * Unless otherwise noted, all measurements performed as downconverter. 3 - 154 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC620 v01.1007 GaAs MMIC I/Q MIXER 3 - 7 GHz Data taken As IRM With External IF 90˚ Hybrid Conversion Gain vs. Temperature Image Rejection vs. Temperature 0 -5 -10 +25 C +85 C -55 C -15 -20 2.5 3.5 4.5 5.5 6.5 -30 3.5 0 -5 -5 -10 +11 dBm +13 dBm +15 dBm +17 dBm 7.5 6.5 7.5 6.5 7.5 -10 -15 RF LO -20 3.5 4.5 5.5 6.5 -30 2.5 7.5 3.5 RF FREQUENCY (GHz) 4.5 5.5 FREQUENCY (GHz) Input P1dB vs. Temperature Input IP3 vs. LO Drive 20 30 18 +25 C +85 C -55 C 25 IP3 (dBm) 16 P1dB (dBm) 6.5 -25 -25 -30 2.5 5.5 Return Loss 0 RETURN LOSS (dB) CONVERSION GAIN (dB) Conversion Gain vs. LO Drive -20 4.5 RF FREQUENCY (GHz) RF FREQUENCY (GHz) -15 3 -20 -40 2.5 7.5 +25 C +85 C -55 C -10 MIXERS - I/Q MIXERS / IRM - CHIP IMAGE REJECTION (dB) CONVERSION GAIN (dB) 0 14 12 20 15 10 LO = +11 dBm LO = +15 dBm LO = +19 dBm 10 8 6 2.5 3.5 4.5 5.5 RF FREQUENCY (GHz) 6.5 7.5 5 2.5 3.5 4.5 5.5 RF FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 - 155 HMC620 v01.1007 GaAs MMIC I/Q MIXER 3 - 7 GHz IF Bandwidth* -10 0 -20 -5 RESPONSE (dB) -30 -40 -50 LO/RF RF/IF1 LO/IF1 RF/IF2 LO/IF2 -60 -70 -80 2.5 3.5 4.5 5.5 -10 -15 CONVERSION GAIN RETURN LOSS -20 -25 6.5 -30 0.5 7.5 1 RF FREQUENCY (GHz) PHASE BALANCE (degrees) LO = 13 dBm LO = 15 dBm LO = 17 dBm 3 0 -1 3.5 4.5 5.5 6.5 0 -5 -10 LO = +13 dBm LO = +15 dBm LO = +17 dBm -15 -20 2.5 7.5 3.5 4.5 5.5 6.5 7.5 RF FREQUENCY (GHz) Upconverter Performance Conversion Gain vs. LO Drive Upconverter Performance Sideband Rejection vs. LO Drive 0 SIDEBAND REJECTION (dBc) 0 -5 -10 LO = +13 dBm LO = +15 dBm LO = +17 dBm -15 3.5 4.5 5.5 6.5 RF FREQUENCY (GHz) 7.5 -10 LO = +13 dBm LO = +15 dBm LO = +17 dBm -20 -30 -40 -50 -60 2.5 3.5 4.5 5.5 6.5 RF FREQUENCY (GHz) * Conversion gain data taken with external IF 90˚ hybrid 3 - 156 3.5 5 RF FREQUENCY (GHz) CONVERSION GAIN (dB) 2.5 10 1 -20 2.5 2 Phase Balance vs. LO Drive 2 -2 2.5 1.5 IF FREQUENCY (GHz) Amplitude Balance vs. LO Drive AMPLITUDE BALANCE (dB) MIXERS - I/Q MIXERS / IRM - CHIP 3 ISOLATION (dB) Isolations For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7.5 HMC620 v01.1007 GaAs MMIC I/Q MIXER 3 - 7 GHz Harmonics of LO MxN Spurious Outputs nLO Spur at RF Port nLO LO Freq. (GHz) 2 3 4 mRF 0 1 2 3 4 2.5 29 35 48 30 0 xx 1 15 28 69 3 26 33 51 39 1 15 0 30 39 50 4 28 32 39 43 2 69 67 78 60 71 5 28 36 45 52 3 95 95 95 73 95 6 36 44 60 41 4 95 95 95 95 95 7 40 36 58 34 8 46 37 55 46 LO = +15 dBm Values in dBc below input LO level measured at RF Port. Absolute Maximum Ratings RF / IF Input +20 dBm LO Drive +27 dBm Channel Temperature 150 °C Continuous Pdiss (T=85°C) (derate 14.2 mW/°C above 85°C) 925 mW Thermal Resistance (RTH) (channel to die bottom) 70.2 °C/W Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C Outline Drawing RF = 5.6 GHz @ -10 dBm LO = 5.5 GHz @ +15 dBm Data taken without IF 90˚ hybrid All values in dBc with reference to output power at IF= 100 MHz ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Die Packaging Information [1] Standard Alternate WP-3 (Waffle Pack) [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM] 2. DIE THICKNESS IS .004” 3. TYPICAL BOND PAD IS .004” SQUARE 4. BACKSIDE METALIZATION: GOLD 5. BOND PAD METALIZATION: GOLD 6. BACKSIDE METAL IS GROUND 7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. 8. OVERALL DIE SIZE ±.002” For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 MIXERS - I/Q MIXERS / IRM - CHIP 1 3 - 157 HMC620 v01.1007 GaAs MMIC I/Q MIXER 3 - 7 GHz Pad Descriptions MIXERS - I/Q MIXERS / IRM - CHIP 3 3 - 158 Pad Number Function Description 1 RF This pad is DC coupled and matched to 50 Ohms. 2 (5) IF2 3 (6) IF1 4 LO This pad is DC coupled and matched to 50 Ohms. GND The backside of the die must be connected to RF/DC ground. Interface Schematic This pad is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pad must not source/sink more than 3mA of current or die nonfunction and possible die failure will result. Pads 5 and 6 are alternate IF ports. Assembly Diagrams For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC620 v01.1007 GaAs MMIC I/Q MIXER 3 - 7 GHz Mounting & Bonding Techniques for Millimeterwave GaAs MMICs 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane Microstrip substrates should be brought as close to the die as possible in order to minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils). Handling Precautions 0.127mm (0.005”) Thick Alumina Thin Film Substrate Follow these precautions to avoid permanent damage. Figure 1. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane 0.150mm (0.005”) Thick Moly Tab Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. 0.254mm (0.010”) Thick Alumina Thin Film Substrate Figure 2. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. 3 MIXERS - I/Q MIXERS / IRM - CHIP The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). Wire Bonding Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 - 159