2 Ω, CMOS, ±5 V/+5 V SPST Switches ADG601/ADG602 Data Sheet FUNCTIONAL BLOCK DIAGRAMS Low on resistance, 2.5 Ω maximum <0.65 Ω on-resistance flatness Dual ±2.7 V to ±5.5 V or single +2.7 V to +5.5 V supplies Rail-to-rail input signal range Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die Low power consumption TTL-/CMOS-compatible inputs S D S D IN ADG601 IN ADG602 NOTES 1. SWITCHES SHOWN FOR A LOGIC 0 INPUT. 02619-001 FEATURES Figure 1. APPLICATIONS Automatic test equipment Power routing Communication systems Data acquisition systems Sample-and-hold systems Avionics Relay replacement Battery-powered systems Table 1. Truth Table ADG601 IN 0 1 ADG602 IN 1 0 GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The ADG601/ADG602 are monolithic, CMOS single-pole single-throw (SPST) switches with on resistance typically less than 2.5 Ω. The low on-resistance flatness makes the ADG601/ ADG602 ideally suited to many applications, particularly those requiring low distortion. These switches are ideal replacements for mechanical relays because they are more reliable, have lower power requirements, and are available in much smaller package sizes. 1. 2. 3. 4. Switch Condition Off On Low on resistance (2 Ω typical) Dual ±2.7 V to ±5.5 V or single +2.7 V to +5.5 V supplies Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die Rail-to-rail input signal range The ADG601 is a normally open (NO) switch, and the ADG602 is a normally closed (NC) switch. Each switch conducts equally well in both directions when the device is on, with the input signal range extending to the supply rails. The switches are available in tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die. Rev. D Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2001–2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADG601/ADG602 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Absolute Maximum Ratings ............................................................5 Applications ....................................................................................... 1 ESD Caution...................................................................................5 Functional Block Diagrams ............................................................. 1 Pin Configurations and Function Descriptions ............................6 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................7 Product Highlights ........................................................................... 1 Terminology .......................................................................................9 Revision History ............................................................................... 2 Test Circuits ..................................................................................... 10 Specifications..................................................................................... 3 Outline Dimensions ....................................................................... 11 Dual Supply ................................................................................... 3 Ordering Guide .......................................................................... 12 Single Supply ................................................................................. 4 REVISION HISTORY 3/15—Rev. C to Rev. D Changes to IR Reflow, Peak Temperature Parameter, Table 4 .... 5 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 12 3/07—Rev. B to Rev. C Added Die Package ............................................................. Universal Changes to Specifications ................................................................ 3 Added Figure 4 and Table 6 ............................................................. 6 Changes to Ordering Guide .......................................................... 11 3/06—Rev. A to Rev. B Updated Format .................................................................. Universal Changes to 6-Lead SOT-23 (RJ-6) Pin Configuration .................6 Added Pin Function Descriptions Table ........................................6 Changes to Figure 19.........................................................................9 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 11 6/03—Rev. 0 to Rev. A Changes to Specifications .................................................................2 Changes to Ordering Guide .............................................................4 Updated Outline Dimensions ..........................................................8 11/01—Revision 0: Initial Version Rev. D | Page 2 of 12 Data Sheet ADG601/ADG602 SPECIFICATIONS DUAL SUPPLY VDD = 5 V ± 10%, VSS = –5 V ± 10%, GND = 0 V, unless otherwise noted. Table 2. Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On-Resistance Flatness (RFLAT (ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off ) Drain Off Leakage, ID (Off ) Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH +25°C B Version1 −40°C to +85°C VSS to VDD 2 2.5 0.35 0.6 ±0.01 ±0.25 ±0.01 ±0.25 ±0.01 ±0.25 5.5 0.4 0.65 ±1 ±1 ±1 2.4 0.8 0.005 tOFF Charge Injection Off Isolation Bandwidth −3 dB CS (Off ) CD (Off ) CD, CS (On) POWER REQUIREMENTS IDD 2 80 120 45 75 250 −60 180 50 50 145 155 90 0.001 1.0 ISS 0.001 1.0 1 2 Test Conditions/Comments V Ω typ Ω max Ω typ Ω max VDD = +4.5 V, VSS = –4.5 V VS = ±4.5 V, IDS = −10 mA; see Figure 15 nA typ nA max nA typ nA max nA typ nA max ±0.1 Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS2 tON Unit V min V max μA typ μA max pF typ ns typ ns max ns typ ns max pC typ dB typ MHz typ pF typ pF typ pF typ μA typ μA max μA typ μA max Temperature range for B version is −40°C to +85°C. Guaranteed by design, not subject to production test. Rev. D | Page 3 of 12 VS = ±3.3 V, IDS = −10 mA VDD = +5.5 V, VSS = −5.5 V VS = +4.5 V/−4.5 V, VD = −4.5 V/+4.5 V; see Figure 16 VS = +4.5 V/−4.5 V, VD = −4.5 V/+4.5 V; see Figure 16 VS = VD = +4.5 V or −4.5 V; see Figure 17 VIN = VINL or VINH RL = 300 Ω, CL = 35 pF VS = 3.3 V; see Figure 18 RL = 300 Ω, CL = 35 pF VS = 3.3 V; see Figure 18 VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 19 RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 20 RL = 50 Ω, CL = 5 pF; see Figure 21 f = 1 MHz f = 1 MHz f = 1 MHz VDD = +5.5 V, VSS = −5.5 V Digital inputs = 0 V or 5.5 V Digital inputs = 0 V or 5.5 V ADG601/ADG602 Data Sheet SINGLE SUPPLY VDD = 5 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 3. Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On-Resistance Flatness (RFLAT (ON)) LEAKAGE CURRENTS Source Off Leakage, IS (Off ) Drain Off Leakage, ID (Off ) Channel On Leakage, ID, IS (On) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH +25°C B Version1 −40°C to +85°C 0 V to VDD 3.5 5 0.2 ±0.01 ±0.25 ±0.01 ±0.25 ±0.01 ±0.25 8 0.2 0.6 ±1 ±1 ±1 2.4 0.8 tOFF Charge Injection Off Isolation Bandwidth –3 dB CS (Off ) CD (Off ) CD, CS (On) POWER REQUIREMENTS IDD 2 V Ω typ Ω max Ω typ Ω max VDD = 4.5 V VS = 0 V to 4.5 V, IDS = −10 mA; see Figure 15 nA typ nA max nA typ nA max nA typ nA max 2 110 220 50 80 20 −60 180 50 50 145 ns typ ns max ns typ ns max pC typ dB typ MHz typ pF typ pF typ pF typ 0.005 280 110 0.001 1.0 1 Test Conditions/Comments V min V max μA typ μA max pF typ ±0.1 Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS2 tON Unit Temperature range for B version is −40°C to +85°C. Guaranteed by design, not subject to production test. Rev. D | Page 4 of 12 μA typ μA max VS = 1.5 V to 3.3 V, IDS = –10 mA VDD = 5.5 V VS = 4.5 V/1 V, VD = 1 V/4.5 V; see Figure 16 VS = 4.5 V/1 V, VD = 1 V/4.5 V; see Figure 16 VS = VD = 4.5 V or 1 V; see Figure 17 VIN = VINL or VINH RL = 300 Ω, CL = 35 pF VS = 3.3 V; see Figure 18 RL = 300 Ω, CL = 35 pF VS = 3.3 V; see Figure 18 VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 19 RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 20 RL = 50 Ω, CL = 5 pF; see Figure 21 f = 1 MHz f = 1 MHz f = 1 MHz VDD = 5.5 V Digital inputs = 0 V or 5.5 V Data Sheet ADG601/ADG602 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 4. Parameter VDD to VSS VDD to GND VSS to GND Analog Inputs1 Digital Inputs1 Continuous Current, S or D Peak Current, S or D (Pulsed at 1 ms, 10% Duty Cycle Max) Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature Thermal Resistance MSOP θJA θJC SOT-23 θJA θJC Lead Temperature, Soldering (10 sec) IR Reflow, Peak Temperature 1 Rating 13 V −0.3 V to +6.5 V +0.3 V to –6.5 V VSS − 0.3 V to VDD + 0.3 V −0.3 V to VDD + 0.3 V or 30 mA (whichever occurs first) 100 mA Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Only one absolute maximum rating may be applied at a time. ESD CAUTION 200 mA −40°C to +85°C −65°C to +150°C 150°C 206°C/W 44°C/W 229.6°C/W 91.99°C/W 300°C 260°C Overvoltages at IN, S, or D are clamped by internal diodes. Current should be limited to the maximum ratings given. Rev. D | Page 5 of 12 ADG601/ADG602 Data Sheet S 2 PIN 1 INDICATOR ADG601/ ADG602 TOP VIEW (Not to Scale) VSS 3 6 5 4 IN GND D 1 PIN 1 INDICATOR 8 S NC 2 ADG601/ ADG602 7 GND 6 IN 5 VSS NC 3 D VDD 4 02619-002 VDD 1 TOP VIEW (Not to Scale) NC = NO CONNECT Figure 2. 6-Lead SOT-23 (RJ-6) 02619-003 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 3. 8-Lead MSOP (RM-8) Table 5. Pin Function Descriptions Pin No. 6-Lead SOT-23 8-Lead MSOP 1 4 2 8 3 5 4 7 5 1 6 6 N/A1 2, 3 Description Most Positive Power Supply Potential. Source Terminal. Can be an input or output. Most Negative Power Supply Potential. Ground (0 V) Reference. Drain Terminal. Can be an input or output. Logic Control Input. No Connect. N/A is not applicable. 1 2 14 13 3 4 12 5 6 7 11 10 9 8 TOP VIEW (Not to Scale) 02619-021 1 Mnemonic VDD S VSS GND D IN NC Figure 4. Die (820 μm × 2255 μm) Table 6. Die Pad Coordinates1 Die Pad No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Die Pad Coordinates X (μm) Y (μm) −265 +754 −265 +525 −265 +241 −265 +141 −265 −191 −265 −409 −265 −549 −265 −787 +265 −767 +265 −429 +265 −289 +265 +189 +265 +521 +265 +661 Mnemonic NC D D D NC NC NC VDD VSS IN GND S S NC Description No Connect. Drain Terminal. Can be an input or output.2 Drain Terminal. Can be an input or output.2 Drain Terminal. Can be an input or output.2 No Connect. No Connect. No Connect. Most Positive Power Supply Potential. Most Negative Power Supply Potential. Logic Control Input. Ground (0 V) Reference. Source Terminal. Can be an input or output.3 Source Terminal. Can be an input or output.3 Source Terminal. Can be an input or output. 1 Measured from the center of the die. Bond the D pads together to a single point to preserve the on resistance and current handling capability. The common point acts as the drain pin of the switch. 3 Bond the S pads together to a single point to preserve the on resistance and current handling capability. The common point acts as the source pin of the switch. 2 Rev. D | Page 6 of 12 Data Sheet ADG601/ADG602 TYPICAL PERFORMANCE CHARACTERISTICS 5 5 TA = 25°C +85°C 4 4 ON RESISTANCE (Ω) ON RESISTANCE (Ω) ±2.5V ±3V 3 ±3.3V ±4.5V 2 1 3 +25°C 2 –40°C 1 ±5V –3 –2 –1 0 1 VD, VS (V) 2 3 4 5 0 10 VDD = 2.7V 1.5 2.0 2.5 3.0 VD, VS (V) 3.5 4.0 0.3 LEAKAGE CURRENT (nA) VDD = 3.0V 7 6 5 VDD = 4.5V VDD = 3.3V 4 3 2 1 0 0.5 5.0 0.2 ID, IS (ON) 0.1 0 –0.1 ID (OFF) IS (OFF) –0.2 –0.3 VDD = 5.0V TA = 25°C VSS = 0V 4.5 VDD = +5V VSS = –5V VD = ±4.5V VS = 4.5V 0.4 –0.4 1.0 1.5 2.0 2.5 3.0 VD, VS (V) 3.5 4.0 4.5 5.0 –0.5 02619-005 Figure 6. On Resistance vs. VD, VS (Single Supply) 0 10 20 30 40 50 60 TEMPERATURE (°C) 70 80 85 Figure 9. Leakage Currents vs. Temperature (Dual Supply) 5 0.5 VDD = +5V VSS = –5V VDD = 5V VSS = 0V VD = 4.5V/1V VS = 1V/4.5V 0.4 4 LEAKAGE CURRENT (nA) 0.3 3 +85°C +25°C 2 1 0.2 ID, IS (ON) 0.1 0 –0.1 ID (OFF) –0.2 IS (OFF) –0.3 –40°C –4 –3 –2 –1 0 1 VD, VS (V) 2 3 4 5 –0.5 02619-006 –5 –0.4 Figure 7. On Resistance vs. VD, VS for Different Temperatures (Dual Supply) Rev. D | Page 7 of 12 0 10 20 30 40 50 60 TEMPERATURE (°C) 70 80 85 Figure 10. Leakage Currents vs. Temperature (Single Supply) 02619-008 ON RESISTANCE (Ω) 8 ON RESISTANCE (Ω) 1.0 0.5 9 0 0.5 Figure 8. On Resistance vs. VD, VS for Different Temperatures (Single Supply) Figure 5. On Resistance vs. VD, VS (Dual Supply) 0 0 02619-009 –4 02619-004 –5 ± 0 02619-007 VDD = 5V VSS = 0V ADG601/ADG602 Data Sheet 500 0 TA = 25°C 450 –10 –20 350 OFF ISOLATION (dB) VDD = +5V VSS = –5V 300 250 200 VDD = +5V VSS = 0V 150 –40 –50 –60 100 VDD = +5V VSS = –5V TA = 25°C –70 50 –5 –4 –3 –2 –1 0 VS (V) 1 2 3 4 5 –80 0.2 02619-010 0 –30 Figure 11. Charge Injection vs. Source Voltage 1 10 FREQUENCY (MHz) 100 02619-012 CHARGE INJECTION (pC) 400 Figure 13. Off Isolation vs. Frequency 0 180 160 ON RESPONSE (dB) VDD = +5V VSS = –5V tON 80 60 tOFF –4 –6 –8 40 0 –40 –20 0 20 40 TEMPERATURE (°C) –10 VDD = +5V VSS = –5V 60 80 VDD = +5V VSS = –5V TA = 25°C –12 0.2 1 10 FREQUENCY (MHz) 100 Figure 14. On Response vs. Frequency Figure 12. tON/tOFF Times vs. Temperature Rev. D | Page 8 of 12 400 02619-013 VDD = +5V VSS = 0V 20 02619-011 TIME (ns) 120 100 –2 VDD = +5V VSS = 0V 140 Data Sheet ADG601/ADG602 TERMINOLOGY VDD Most positive power supply potential. VINL Maximum input voltage for Logic 0. VSS Most negative power supply potential. VINH Minimum input voltage for Logic 1. IDD Positive supply current. IINL (IINH) Input current of the digital input. ISS Negative supply current. CS (Off) Off switch source capacitance. Measured with reference to ground. GND Ground (0 V) reference. CD (Off) Off switch drain capacitance. Measured with reference to ground. S Source terminal. Can be an input or an output. CD, CS (On) On switch capacitance. Measured with reference to ground. D Drain terminal. Can be an input or an output. CIN Digital input capacitance. IN Logic control input. tON Delay between applying the digital control input and the output switching on. VD, VS Analog voltage on Terminal D and Terminal S. tOFF Delay between applying the digital control input and the output switching off. RON Ohmic resistance between Terminal D and Terminal S. RFLAT (ON) Flatness is defined as the difference between the maximum and minimum values of on resistance as measured over the specified analog signal range. IS (Off) Source leakage current with the switch off. ID (Off) Drain leakage current with the switch off. ID, IS (On) Channel leakage current with the switch on. Charge Injection A measure of the glitch impulse transferred from the digital input to the analog output during switching. Off Isolation A measure of unwanted signal coupling through an off switch. On Response Frequency response of the on switch. Insertion Loss Loss due to the on resistance of the switch. Rev. D | Page 9 of 12 ADG601/ADG602 Data Sheet TEST CIRCUITS IDS V1 A D ID (OFF) VD Figure 15. On Resistance S NC A VS 02619-014 VDD VSS VDD VSS NC = NO CONNECT Figure 17. On Leakage 0.1µF ADG601 50% 50% 50% 50% VIN S VS A VD Figure 16. Off Leakage 0.1µF ID (ON) D VOUT D RL 300Ω IN VIN ADG602 CL 35pF 90% VOUT 90% GND tON tOFF 02619-017 RON = V1/IDS VS S 02619-015 D 02619-016 IS (OFF) S Figure 18. Switching Times VS VSS VDD VSS S D VOUT CL 1nF IN GND VIN ADG601 ON OFF VIN ADG602 VOUT ∆VOUT QINJ = CL × ∆VOUT 02619-018 RS VDD Figure 19. Charge Injection VSS VDD NETWORK ANALYZER VSS VDD S 50Ω IN VSS 0.1µF 0.1µF 0.1µF NETWORK ANALYZER VSS VDD S 50Ω 50Ω IN VS D VS D RL 50Ω GND OFF ISOLATION = 20 log VOUT VS VOUT VIN RL 50Ω GND 02619-019 VIN INSERTION LOSS = 20 log Figure 20. Off Isolation VOUT WITH SWITCH VS WITHOUT SWITCH Figure 21. Bandwidth Rev. D | Page 10 of 12 VOUT 02619-020 VDD 0.1µF Data Sheet ADG601/ADG602 OUTLINE DIMENSIONS 3.20 3.00 2.80 8 3.20 3.00 2.80 5.15 4.90 4.65 5 1 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15° MAX 1.10 MAX 0.80 0.55 0.40 0.23 0.09 6° 0° 0.40 0.25 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 22. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 3.00 2.90 2.80 1.70 1.60 1.50 6 5 4 1 2 3 PIN 1 INDICATOR 3.00 2.80 2.60 0.95 BSC 1.90 BSC 0.15 MAX 0.05 MIN 1.45 MAX 0.95 MIN 0.50 MAX 0.30 MIN 0.20 MAX 0.08 MIN SEATING PLANE 10° 4° 0° 0.60 BSC COMPLIANT TO JEDEC STANDARDS MO-178-AB Figure 23. 6-Lead Small Outline Transistor Package [SOT-23] (RJ-6) Dimensions shown in millimeters Rev. D | Page 11 of 12 0.55 0.45 0.35 12-16-2008-A 1.30 1.15 0.90 ADG601/ADG602 Data Sheet ORDERING GUIDE Model1 ADG601BRTZ-REEL ADG601BRTZ-REEL7 ADG601BRMZ ADG601BRMZ-REEL7 ADG601C-PT7 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 6-Lead SOT-23 6-Lead SOT-23 8-Lead MSOP 8-Lead MSOP Die Package Option RJ-6 RJ-6 RM-8 RM-8 Branding2 STB# STB# S1G S1G ADG602BRTZ-REEL7 ADG602BRMZ −40°C to +85°C −40°C to +85°C 6-Lead SOT-23 8-Lead MSOP RJ-6 RM-8 S18 S18 ADG602BRMZ-REEL7 −40°C to +85°C 8-Lead MSOP RM-8 S18 1 2 Z = RoHS Compliant Part, # denotes RoHS compliant product, may be top or bottom marked. Branding on SOT-23 and MSOP is limited to three characters due to space constraints. ©2001–2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D02619-0-3/15(D) Rev. D | Page 12 of 12