Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC547LC3 v01.0514 Switches - SPDT - SMT GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz Typical Applications Features The HMC547LC3 is ideal for: High Isolation: 45 dB @ 10 GHz 40 dB @ 20 GHz • Fiber Optics & Broadband Telecom Low Insertion Loss: 1.6 dB @ 10 GHz 1.9 dB @ 20 GHz • Microwave Radio & VSAT • Military Radios, Radar, & ECM Fast Switching: 6 ns • Test Instrumentation Non-Reflective Design 16 Lead Ceramic 3x3 mm SMT Package: 9mm2 Functional Diagram General Description The HMC547LC3 is a general purpose broadband high isolation non-reflective GaAs MESFET SPDT switch in a ceramic 3x3 mm leadless surface mount package. Covering DC to 28.0 GHz, the switch offers over 40 dB isolation and less than 2 dB insertion loss at midband. The wide bandwidth, fast switching, and compact size make this absorbtive SPDT ideal for miliitary EW/ECM and test equipment applications. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. Electrical Specifications, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter Insertion Loss Isolation DC - 10.0 GHz 10.0 - 20.0 GHz 20.0 - 28.0 GHz Return Loss Return Loss RF1, RF2 1 Frequency DC - 10.0 GHz 10.0 - 20.0 GHz 20.0 - 28.0 GHz Min. 40 34 30 Typ. Max. Units 1.6 1.9 2.4 2.2 2.5 3.0 dB dB dB 45 40 34 dB dB dB “On State” DC - 28.0 GHz 17 dB “Off State” DC - 10.0 GHz 10.0 - 20.0 GHz 20.0 - 28.0 GHz 25 15 8 dB dB dB 16 23 dBm Input Power for 1 dB Compression DC - 0.5 GHz 0.5 - 28.0 GHz Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone) DC - 0.5 GHz 0.5 - 28.0 GHz 26 46 dBm dBm Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 28.0 GHz 3 6 ns ns 20 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC547LC3 v01.0514 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz Return Loss Insertion Loss -1 -2 +25 C +85 C -40 C -3 -4 -5 RFC RF1,RF2 ON RF1,RF2 OFF -10 -20 -30 -40 0 5 10 15 20 25 30 0 5 10 FREQUENCY (GHz) Isolation Between Ports RFC and RF1/RF2 0 -10 -10 ISOLATION (dB) ISOLATION (dB) -40 -50 30 -30 -40 -50 -60 -60 -70 -70 -80 -80 0 5 10 15 20 25 30 0 5 10 FREQUENCY (GHz) 15 20 25 30 FREQUENCY (GHz) Input P1dB and P0.1dB Compression Point Input Third Order Intercept Point 55 30 50 25 INPUT IP3 (dBm) INPUT P1dB AND P0.1dB (dBm) 25 RF1 PATH ON RF2 PATH ON -20 RF1 RF2 -30 20 Isolation Between Ports RF1 and RF2 0 -20 15 FREQUENCY (GHz) Switches - SPDT - SMT 0 RETURN LOSS (dB) INSERTION LOSS (dB) 0 20 P1dB P0.1dB 15 10 0.01 0.1 1 FREQUENCY (GHz) 10 45 40 +25 C +85 C -40 C 35 30 100 25 0.01 0.1 1 10 100 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC547LC3 v01.0514 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz Switches - SPDT - SMT Absolute Maximum Ratings 3 Control Voltages RF Input Power (A,B = 0V/-5V) +25 dBm State Bias Condition Control Voltage Range (A & B) +5.0V to -7.5V Low 0 to -0.5V @ 10 uA Max. Hot Switch Power Level (A,B = 0V/-5V) +22 dBm High -5V @ 3 uA Typ. to -7V @ 10 uA Typ. (± 0.5V) Channel Temperature 150 °C Continuous Pdiss (T=85°C) (derate 3.3 mW/°C above 85°C) (Insertion Loss Path) 0.215 W Thermal Resistance (Insertion Loss Path) 302 °C/W Continuous Pdiss (T=85°C) (derate 5.6 mW/°C above 85°C) (Terminated Path) 0.363 W Thermal Resistance (Terminated Path) 179 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A Truth Table Control Input Signal Path State A B RFC to RF1 RFC to RF2 High Low On Off Low High Off On ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC547LC3 v01.0514 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA. 2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER NICKEL. 3. DIMENSIONS ARE IN INCHES (MILLIMETERS). 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05MM DATUM – C – 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Switches - SPDT - SMT Outline Drawing Package Information Part Number Package Body Material Lead Finish HMC547LC3 Alumina, White Gold over Nickel MSL Rating MSL3 [1] Package Marking [2] H547 XXXX [1] Max peak reflow temperature of 260 °C [2] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC547LC3 v01.0514 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz Switches - SPDT - SMT Pin Descriptions 5 Pin Number Function Description 1, 5, 9, 12, 16 N/C This pin should be connected to PCB RF ground to maximize isolation 2, 4, 6, 8, 13, 15 GND Package bottom has exposed metal paddle that must also be connected to PCB RF ground. 3, 7, 14 RFC, RF1, RF2 This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. 10 B See truth table and control voltage table. 11 A See truth table and control voltage table. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC547LC3 v01.0514 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 28.0 GHz Switches - SPDT - SMT Evaluation PCB List of Materials for Evaluation PCB EVAL01-HMC547LC3 [1] Item Description J1 - J3 PCB Mount SRI SMA Connector J4 - J6 DC Pin R1 - R2 100 Ohm Resistor, 0603 Pkg. U1 HMC547LC3 SPDT Switch PCB [2] 600-00005-00-1 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6