ISOCOM LTD ® PART NUMBER CS3081/3082/3083 COMPONENT ISSUE 1 SPECIFICATION October 2013 Component Specification For Ceramic Hermetically Sealed, Radiation Hard Zero Crossing Triac Optocoupler BS9000 M1077 IECQ 1077/M Further copies of this document may be obtained from: ISOCOM LIMITED WASHINGTON, UK NE38 0AH www.isocom.uk.com For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 1 of 10 ISOCOM LTD ® Ceramic Hermetically Sealed, Radiation Hard Zero Crossing Triac Optocoupler ■ CS3081/3082/3083 ■ CS3081/3082/3083/L2 ■ CS3081/3082/3083/L2S Features Applications ▪ Released to European Standard and complies to Mil Std ▪ Space Radiation Equipment ▪ Hermetically Sealed ▪ Military, high reliability system ▪ High Isolation 1500Vdc ▪ Medical instruments ▪ 6 Pin Dual In Line Package ▪ Power Supply ▪ 800V Peak Blocking Voltage ▪ Zero Crossing Voltage Description These devices are single, hermetically sealed optically coupled isolators. Each channel is composed of a Gallium Arsenide infra-red emitting diode coupled to a silicon detector performing the function of a zero voltage crossing bilateral triac driver. The CS3081 series is being used in environments encounted by space applications. It is manufactured to JANS standard in conjunction with MIL-PRF-19500 procedures (please see next page for all other applicable specifications). Package styles for this device include 6 Pin DIL Package with surface mount, solder dip option available. Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 2 of 10 ISOCOM LTD ® Standards The following specifications have been included in the manufacturing of this product: Military Compliance Specifications MIL-PRF-19500 – General Specification for Discrete Semiconductor Devices IECQ – M1077 Military Compliance Standards MIL-STD-202 – Test Method Standard Electronic and Electrical Component Parts MIL-STD-883 – Test Method Standard Microcircuits MIL-STD-750 – Test Methods for Semiconductor Devices ISO 9001:2008 – Manufacturing of Optocouplers and Optoelectronic components. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 3 of 10 ISOCOM LTD ® Selection Guide Package Styles and Configuration Options Package 6 pin DIL Lead Style Channels Common Channel Wiring Isocom Part Number and Options Commercial Defense Screen Level Space Screen Level Standard Gold Plate Finish Butt Joint Solder Dipped Gull Wing Butt Joint 1 CS3081/3082/3083 CS3081/3082/3083/L2 CS3081/3082/3083/L2S Gold Plate Option 10 Option 20 Option 30 Option 60 Functional Diagrams CS3081/3082/3083 6 pin DIL 1 Channel Device Marking ISOCOM XXXXXXX XXXX Outline Drawings For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 4 of 10 Manufacturer Isocom Part Number Date Code (XX year XX week) ISOCOM LTD ® Hermetic Optocoupler Options Option 10 Description Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 6, 8 and 16 pin DIP 4.32 (0.17) Max 0.51 (0.02) Min 1.14 (0.045) 1.40 (0.055) 2.29 (0.09) 2.79 (0.11) 0.51 (0.02) Max 4.32 (0.17) Max 0.51 (0.2) Min 2.29 (0.09) 2.79 (0.11) 0.51 (0.02) Max 0.2 (0.008) 0.33 (0.013) 7.36 (0.29) 7.87 (0.31) 1.14 (0.045) 1.40 (0.055) 20 30 Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 6, 8 and 16 pin DIP. 4.57 (0.18) Max 0.51 (0.02) Min 2.29 (0.9) 2.79 (0.11) 5 deg 4.57 (0.18) Max Max 0.51 (0.02) Min 2.29 (0.09) 2.79 (0.11) 60 1.4 (0.055) 1.65 (0.065) 0.51 (0.02) Max 4.57 (0.18) Max 0.2 (0.008) 0.33 (0.013) 1.4 (0.055) 1.65 (0.065) 0.51 (0.02) Max 9.65 (0.38) 9.91 (0.39) Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 6, 8 and 16 pin DIP 3.81 (0.15) Min 0.51 (0.02) Min 2.29 (0.09) 2.79 (0.11) 3.81 (0.15) Max 0.2 (0.008) 0.33 (0.013) 7.36 (0.29) 7.87 (0.31) 1.14 (0.045) 1.25 (0.049) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 5 of 10 0.51 (0.02) Min 2.29 (0.09) 2.79 (0.11) 1.02 (0.04) Typ ISOCOM LTD ® Absolute Maximum Ratings TA = 25°C U.O.S. Storage Temperature Operating Temperature Normal Temperature Range (No Derating) Lead Soldering Temperature Input-to-Output Isolation Voltage (Peak) -40°C to +150°C -40°C to +85°C -55°C to +50°C 260°C 1.6mm from case for 10S 1500V (60Hz, 5 sec duration) Input Diode Forward DC Current Reverse DC Voltage Power Dissipation 60mA 6V 120mW Derate linearly above 25°C at 1.33mW/°C. 800V 100mA 1.2A 150mW 250mW P.W. = 10m.Sec Derate linearly above 25°C at 4.0mW/°C Derate linearly above 25°C at 4.4mW/°C Output Photo Triac Off-State Output Terminal Voltage RMS Forward Current Forward Current (Peak) Power Dissipation Total Power Dissipation Electrical Characteristics TA = 25°C U.O.S. Input Diode Electrical Characteristics Parameter Forward Voltage Reverse Current Symbol VF IR Test Conditions IF = 30mA VR= 3.0V Min - Typ - Max 1.5 100 Units V µA Output Photo-SCR Characteristics Peak Off-State Current Peak Blocking Voltage On-State Voltage Critical rate of rise of commutating Off-state Voltage IDRM VDRM VTM dv/dt(C) VDRM= 250V IDRM= 100nA ITM= 100mA(Peak) 800 600 1.8 1500 100 3.0 - nA V V V/µS IFT Main Terminal Voltage = 3V CS3031 Main Terminal Voltage = 3V CS3032 Main Terminal Voltage = 3V CS3033 1500 100 - 15 10 5 - mA mA mA µA Vac VIH IF = Rated IFM; MT-1,MT-2 voltage above which the device will not trigger. IF= Rated IFT, VDRM= 250V, Off-State 5 20 V 300 500 µA Coupled Electrical Characteristics Input Current to Trigger Holding Current, either Direction Input-to-Output Isolation Voltage Zero Crossing Characteristics Inhibit Voltage Leakage in Inhibited State IR For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 6 of 10 - ISOCOM LTD ® GROUP TESTING to MIL-STD 750 GROUP Group A SG1 SG2 SG3 SG4 Group B SG 1 SG 2 SG 3 TEST MIL-STD-750 Visual inspection & mechanical dimensions DC static test at 25°C DC static test at 125°C and ‐55°C Dynamic test at 25°C Method 2071 Physical dimensions Solderability Resistance to solvents Thermal Shock Electrical measurement Bond strength Acc. steady‐state operation life Method 2066 Method 2026 Method 1022 Method 1056 Cond. B, 25 cycles Method 1051, 100 cycles, -55/+125°C Method 1071, Cond. H (fine), Cond. C (gross) pre and post 2075 Method 2037, Cond. D Method 2017 Method 1037, 1042, Cond D, Tab.5-5 Method 1071, Cond. H (fine), Cond. C (gross) pre and post Method 2037, Cond. D Method 1027 Electrical measurement Bond strength pre and post Method 2037, Cond. D Thermal Shock Method 1056, Cond. B, 25 shocks Method 1051, Cond. C, ‐55/+125°C , 25 cycles (total 45 cycles including screening) Method 1071, Cond. H (fine), Cond. C (gross) Method 1021 pre and post Method 2016, non‐operating, 1500 G, 0.5 ms, 5 blows in each orientation (X1,Y1,Z1) Method 2056 Method 2006, at a peak level of 5000 G pre and post Temperature cycling Hermetic seal fine and gross leak SG 4 Electrical measurement Decap internal visual inspection Bond strength Die shear Intermittent operation life Hermetic seal fine and gross leak SG 5 Group C SG 2 Temperature cycling Hermetic seal fine and gross leak SG 3 Moisture resistance Electrical measurement Mechanical shock Vibration Constant acceleration SG 6 Electrical measurement Steady state operating life Not required as B5 is available on same lot yes yes yes For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 7 of 10 READ AND RECORD yes yes yes yes yes yes yes yes yes ISOCOM LTD ® 100% SCREENING to MIL-STD 750 TEST MIL-STD-750 Internal Visual 2072 READ AND RECORD? Sealing (Fine Leak) (Gross Leak) Temp Cycling Const. Acceler PIND Radiography Initial Electrical HTRB Interim Electrical Burn-In Final Electrical PDA (Fine Leak) (Gross Leak) 1071, Condition H1 1071, Condition C 1051, Condition B‐55/+125°C, 20 Cycles. 2006, 5000G, Y1 only. 2052, Condition A 2076 125°C, ‐55°C, 25°C 1039 25°C only 1039 125°C, ‐55°C, 25°C Max. 5%, pre/post B1 electrical and delta at RT only 1071, Condition H1 1071, Condition C Solder Dip Fine Leak Gross Leak 1071, Condition H1 1071, Condition C For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 8 of 10 R&R R&R R&R Calculate & R ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 9 of 10 ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 10 of 10