ISOCOM LTD ® PART NUMBER CSM150/L2S COMPONENT ISSUE 1 SPECIFICATION January 2014 Component Specification For Ceramic Hermetically Sealed, Radiation Hard Photo-Diode Optocouplers M1077 IECQ 1077/M Further copies of this document may be obtained from: ISOCOM LIMITED WASHINGTON, UK NE38 0AH www.isocom.uk.com For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 1 of 11 ISOCOM LTD ® Ceramic Hermetically Sealed, Radiation Hard Photo-Diode Optocouplers ■ CSM150 ■ CSM150/L2 ■ CSM150/L2S Features Applications ▪ Released to European Standard and Complies to Mil Std ▪ Space Radiation Equipment ▪ Military, high reliability system ▪ Total Ionizing Dose Tested to 150KRad(si) ▪ Medical instruments ▪ Displacement Damage to 1 MEV x 10¹² ▪ Logic Interfacing ▪ High Isolation Voltage 1000vdc ▪ Mos, Cmos Applications ▪ 4 Pin LCC Package ▪ Data Transmission ▪ Low Input Requirements ▪ Power Supply ▪ 200V Breakdown (Typically) High Speed Switching Hermetically Sealed Description These devices are single, hermetically sealed optically coupled isolators. Each channel is composed of a infra-red emitting diode and a silicon photo-diode. The CSM150 series is being used in environments encounted by space applications. It is manufactured to meet the JANS standard in conjunction with MIL-PRF-19500 procedures (please see next page for all other applicable specifications). Package styles for this device include 4 Pin LCC Package with surface mount, solder dip option available. Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 2 of 11 ISOCOM LTD ® Standards The following specifications have been complied with in the manufacturing of this product: Military Compliance Specifications MIL-PRF-19500 – General Specification for Discrete Semiconductor Devices IECQ – M1077 Military Compliance Standards MIL-STD-202 – Test Method Standard Electronic and Electrical Component Parts MIL-STD-883 – Test Method Standard Microcircuits MIL-STD-750 – Test Methods for Semiconductor Devices ISO 9001:2008 – Manufacturing of Optocouplers and Optoelectronic components. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 3 of 11 ISOCOM LTD ® Selection Guide Package Styles and Configuration Options Package 4 pin LCC Lead Style Channels Common Channel Wiring Isocom Part Number and Options Commercial Defense Screen Level Space Screen Level Standard Gold Plate Finish Solder Dipped 1 CSM150 CSM150/L2 CSM150/L2S Gold Plate Option 20 Functional Diagrams CSM150 4 pin LCC 1 Channel Device Marking ISOCOM XXXXXXX XXXX For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 4 of 11 Manufacturer Isocom Part Number Date Code (XX year XX week) ISOCOM LTD ® Outline Drawings C A K L B I Lid grounding stripe J D H 0.2286 R E G F Inches SYMBOL A B C D E F G H I J K L MIN. 0.215 0.145 0.061 0.045 0.032 0.072 0.032 0.022 0.010 0.029 0.036 0.011 Millimetres MAX. 0.225 0.155 0.075 0.055 0.048 0.088 0.048 0.028 0.024 0.044 0.044 0.019 MIN. 5.46 3.68 1.55 1.14 0.81 1.83 0.81 0.56 0.25 0.74 0.91 0.28 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 5 of 11 MAX. 5.71 3.94 1.91 1.40 1.22 2.24 1.22 0.71 0.61 1.12 1.12 0.48 ISOCOM LTD ® Absolute Maximum Ratings TA = 25°C U.O.S. Storage Temperature Operating Temperature Lead Soldering Temperature Input-to-Output Isolation Voltage -65°C to +150°C -55°C to +125°C 260°C 1.6mm from case for 10S 1000VDC Input Diode Forward DC Current 40mA Reverse DC Voltage Peak forward Current Power Dissipation 2V 1.0mA 60mW DC at (or below) +65°C Derates linearly to +125°C free air temperature at the rate of 0.67mA/°C. Pw1µS, PRR<300pps 10µS ms Derates linearly above 65°C at 1.0W/°C Output Diode Reverse Bias Power Dissipation 200V 300mW Coupled Device Input to Output Isolation Voltage Power Dissipation SolderingTemperature,Soldering Iron 1000V 360mW 260,5 °C,s This part shall not be re-soldered until 3 minutes have elapsed. Electrical Characteristics Input Diode Electrical Characteristics TA = 25°C U.O.S. Parameter Forward Voltage Symbol VF Reverse Current IR Test Conditions IF = 10mA IF = 10mA -55°C IF = 10mA +125°C VR = 2.0V Min 1.3 1.3 1.1 - Type - Max 1.8 1.8 1.8 100 Units V V V µA - 100 - µA 200 - - V 1000 - 1.6 1.62 1.0 1.29 1.6 1.56 1.3 105 200 - % % % % % % VP-P Vdc Ω ηS - 200 - ηS Output Detector Electrical Characteristics Dark Current Reverse Breakdown Voltage ID V(BR) RL = 1MΩ,VR = 5V IB = 1mA Coupled Electrical Characteristics DC Current Transfer Ratio IC/IF Output Voltage Isolation Voltage Input to Output Resistance Rise Time VO V in-out R in-out tr Fall Time tf IF(IN) = 15mA, V(OUT) = 5V IF(IN) = 15mA, V(OUT) = 5V IF(IN) = 1.0mA, V(OUT) = 1V IF(IN) = 3.0mA, V(OUT) = 1V IF(IN) = 15mA, V(OUT) = 1V IF(IN) = 10mA, V(OUT) = 5V RL = 3.3KΩ,Vcc = 5V,IF = 75mA T = 5s (Note 2) VIO = 500V (Note 2) RL = 3.3KΩ Vcc = 5V IF = 10mA RL = 3.3KΩ Vcc = 5V IF = 10mA Notes: 1) Sample and hold pulse shall not be longer than 0.1 seconds. Duty cycle shall be 10. 2) Measurements with inputs shorted together and outputs shorted together For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 6 of 11 ISOCOM LTD ® GROUP TESTING TO MIL-STD 750 GROUP Group A SG1 SG2 SG3 SG4 Group B SG 1 SG 2 SG 3 TEST MIL-STD-750 Visual inspection & mechanical dimensions DC static test at 25°C DC static test at 125°C and ‐55°C Dynamic test at 25°C Method 2071 Physical dimensions Solderability Resistance to solvents Thermal Shock Electrical measurement Bond strength Acc. steady‐state operation life Method 2066 Method 2026 Method 1022 Method 1056 Cond. B, 25 cycles Method 1051, 100 cycles, -55/+125°C Method 1071, Cond. H (fine), Cond. C (gross) pre and post 2075 Method 2037, Cond. D Method 2017 Method 1037, 1042, Cond D, Tab.5-5 Method 1071, Cond. H (fine), Cond. C (gross) pre and post Method 2037, Cond. D Method 1027 Electrical measurement Bond strength pre and post Method 2037, Cond. D Thermal Shock Method 1056, Cond. B, 25 shocks Method 1051, Cond. C, ‐55/+125°C , 25 cycles (total 45 cycles including screening) Method 1071, Cond. H (fine), Cond. C (gross) Method 1021 pre and post Method 2016, non‐operating, 1500 G, 0.5 ms, 5 blows in each orientation (X1,Y1,Z1) Method 2056 Method 2006, at a peak level of 5000 G pre and post Temperature cycling Hermetic seal fine and gross leak SG 4 Electrical measurement Decap internal visual inspection Bond strength Die shear Intermittent operation life Hermetic seal fine and gross leak SG 5 Group C SG 2 Temperature cycling Hermetic seal fine and gross leak SG 3 Moisture resistance Electrical measurement Mechanical shock Vibration Constant acceleration SG 6 Electrical measurement Steady state operating life Not required as B5 is available on same lot yes yes yes For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited READ AND RECORD Page 7 of 11 yes yes yes yes yes yes yes yes yes ISOCOM LTD ® 100% SCREENING TO MIL-STD 750 TEST MIL-STD-750 Internal Visual 2072 READ AND RECORD? Sealing (Fine Leak) (Gross Leak) Temp Cycling* Const. Acceler* PIND Radiography Initial Electrical HTRB Interim Electrical Burn-In Final Electrical PDA (Fine Leak) (Gross Leak) 1071, Condition H1 1071, Condition C 1051, Condition B‐55/+125°C, 20 Cycles. 2006, 5000G, Y1 only. 2052, Condition A 2076 125°C, ‐55°C, 25°C 1039 25°C only 1039 125°C, ‐55°C, 25°C Max. 5%, pre/post B1 electrical and delta at RT only 1071, Condition H1 1071, Condition C R&R R&R R&R Calculate & R Solder Dip Fine Leak Gross Leak 1071, Condition H1 1071, Condition C * The parts are electrical tested before and after & recorded to MIL-STD-750 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 8 of 11 ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 9 of 11 ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 10 of 11