Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC641ALC4 v00.0713 SWITCHES - SP4T - SMT GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Typical Applications Features The HMC641ALC4 is ideal for: Broadband Performance: DC - 20 GHz • Telecom Infrastructure High Isolation: 42 dB @ 12 GHz • Microwave Radio & VSAT Low Insertion Loss: 2.1 dB @ 12 GHz • Military & Space Hybrids Integrated 2:4 TTL Decoder • Test Instrumentation 24 Lead 4x4mm SMT Package: 16mm² • SATCOM & Sensors General Description Functional Diagram The HMC641ALC4 is a broadband non-reflective GaAs pHEMT SP4T switch in a compact 4x4 mm ceramic package. Covering DC to 20 GHz, this switch offers high isolation, low insertion loss and on-chip termination of isolated ports. This switch also includes an on board binary decoder circuit which reduces the number of required logic control lines from four to two. The HMC641ALC4 is controlled with 0/ -5V logic, exhibits fast switching speed and consumes much less DC current than pin diode based solutions. Electrical Specifications, TA = +25° C, With 0/-5V Control, Vss = -5V, 50 Ohm System Parameter Insertion Loss Isolation (RFC to RF1 - RF4) DC - 12 GHz DC - 20 GHz Return Loss “On State” Return Loss “Off State” Min. 30 30 DC - 12 GHz DC - 20 GHz DC - 20 GHz 10 20 Typ. Max. Units 1.8 2.3 2.8 3.5 dB dB 42 40 dB dB 18 17 dB dB 19 dB 15 25 dBm dBm Input Power for 1 dB Compression 0.05 - 0.25 GHz 0.25- 20 GHz Input Third Order Intercept (Two-Tone Input Power= +10 dBm Each Tone) 0.05 - 0.25 GHz 0.25 - 20 GHz 32 41 dBm dBm DC - 20 GHz 30 100 ns ns Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 1 Frequency DC - 12 GHz DC - 20 GHz For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641ALC4 v00.0713 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Insertion Loss vs. Temperature Isolation 0 -1 -20 ISOLATION (dB) INSERTION LOSS (dB) -10 -2 -3 -30 -40 -50 -60 -4 -70 -5 -80 0 4 8 12 16 20 0 24 4 8 +25 C +85 C -40 C Return Loss 16 20 24 RF1 RF3 RF2 RF4 1 dB Input Compression Point 30 INPUT COMPRESSION POINT (dBm) 0 -5 RETURN LOSS (dB) 12 FREQUENCY (GHz) FREQUENCY (GHz) -10 -15 -20 -25 -30 -35 SWITCHES - SP4T - SMT 0 25 20 15 10 0 4 8 12 16 20 24 0 2 4 6 FREQUENCY (GHz) 8 10 12 14 16 18 20 FREQUENCY (GHz) RFC RF1,2,3,4 On RF1,2,3,4 Off Input Third Order Intercept Point @ 10 dBm Tone Power 50 45 IP3 (dBm) 40 35 30 25 20 15 0 5 10 15 20 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC641ALC4 v00.0713 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz SWITCHES - SP4T - SMT Absolute Maximum Ratings 3 Bias Voltage (Vss) -7V Control Voltage Range (A & B) Vss -0.5V to +1V Channel Temperature Signal Path State B High High RF1 +26.5 dBm +23 dBm Low High RF2 High Low RF3 150 °C Low Low RF4 Thermal Resistance Channel to die bottom Insertion Loss Path Terminated Path Control Input A Maximum Input Power Insertion Loss Path Terminated Path Truth Table 201 °C/W 321 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS RFC to: Bias Voltage & Current Vss Range= -5.0 Vdc ±10% Vss (Vdc) Iss (Typ) (mA) Iss (Max) (mA) -5 1.8 5.0 TTL/CMOS Control Voltages State Bias Condition Low -2.5V to 0V @ 30 µA Typ. High -5V to -3.8V @ 0.5 µA Typ. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641ALC4 v00.0713 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz SWITCHES - SP4T - SMT Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish HMC641ALC4 Alumina, White Gold over Nickel MSL Rating MSL3 [1] Package Marking [2] H641A XXXX [1] Max peak reflow temperature of 260 °C [2] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC641ALC4 v00.0713 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Pin Descriptions SWITCHES - SP4T - SMT Pin Number 5 Function Description 1, 5, 6, 13, 18 N/C These pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 2, 4, 7, 9, 10, 12, 17, 19, 21, 22, 24 Ground Paddle GND These pins and the exposed ground paddle must be connected to RF/DC ground. 3, 8, 11, 20, 23 RFC, RF1, RF2, RF3, RF4 These pads are DC coupled and matched to 50 Ohms. Blocking capacitors are required if RF line potential is not equal to 0V. 14 Vss Supply Voltage -5 Vdc ± 10%. 15 CTLB See Truth Table and Control Voltage Table. 16 CTLA See Truth Table and Control Voltage Table. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC641ALC4 v00.0713 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz SWITCHES - SP4T - SMT Evaluation PCB List of Materials for Evaluation PCB EVAL01 - HMC641ALC4 [1] Item Description J1 - J5 PCB Mount SMA Connector J6 - J9 DC Pin C1 1000 pF Capacitor, 0402 Pkg. U1 HMC641ALC4 Switch PCB [2] 600-00782-00-1 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon FR4 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6