Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC849ALP4CE v00.1013 SWITCHES - SPDT - SMT HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz Typical Applications Features The HMC849ALP4CE is ideal for: High Isolation: up to 60 dB • Cellular/4G Infrastructure Single Positive Control: 0/+3V to +5V • WiMAX, WiBro & Fixed Wireless High Input IP3: +52 dBm • Automotive Telematics Non-Reflective Design • Mobile Radio “All Off” State • Test Equipment 16 Lead 4x4 mm QFN Package: 16 mm² Functional Diagram General Description The HMC849ALP4CE is a high isolation non-reflective DC to 6 GHz GaAs pHEMT SPDT switch in a low cost leadless surface mount package. The switch is ideal for cellular/WiMAX/4G Infrastructure applications yielding up to 60 dB isolation, low 0.8 dB insertion loss and +52 dBm input IP3. Power handling is excellent up through the 5 - 6 GHz WiMAX band with the switch offering a P1dB compression point of +31 dBm. On-chip circuitry allows a single positive voltage control of 0/+3V or 0/+5V at very low DC currents. An enable input (EN) set to logic high will put the switch in an “all off” state. Electrical Specifications, TA = +25 °C, Vctl = 0/Vdd, Vdd = +3V to +5V, 50 Ohm System Parameter Frequency Insertion Loss DC - 2.0 GHz 2.0 - 4.0 GHz 4.0 - 6.0 GHz Isolation (RFC to RF1/RF2) DC - 2.0 GHz 2.0 - 4.0 GHz 4.0 - 6.0 GHz Return Loss (On State) Return Loss (Off State) Input Power for 1 dB Compression +3V +5V Input Third Order Intercept (Two-Tone Input Power = +10 dBm Each Tone) Min. 53 48 35 Typ. Max. Units 0.9 1.0 1.8 1.3 1.5 2.5 dB dB 60 56 50 dB dB DC - 4.0 GHz 4.0 - 6.0 GHz 17 14 dB dB DC - 6.0 GHz 15 dB 27 33 dBm dBm DC - 6.0 GHz 52 dBm DC - 6.0 GHz 60 150 0.35 - 6.0 GHz 24 30 Switching Speed tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 1 600 ns ns For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz 0 -0.5 -5 -1 -10 -1.5 -2 -2.5 -3 -3.5 -15 -20 -25 -30 -35 -4 -40 0 1 2 3 4 5 6 7 0 1 2 FREQUENCY (GHz) 3 4 5 6 7 FREQUENCY (GHz) +25C +85C -40C RFC RF1, RF2 OFF RF1, RF2 ON Isolation Between Ports RFC and RF1 / RF2 Isolation Between Ports RF1 and RF2 0 0 -10 -20 ISOLATION (dB) ISOLATION (dB) -20 -40 -60 SWITCHES - SPDT - SMT Return Loss [1] 0 RETURN LOSS (dB) INSERTION LOSS (dB) Insertion Loss -30 -40 -50 -60 -80 -70 -100 -80 0 1 2 3 4 5 6 0 7 1 2 3 4 6 7 RFC-RF1 ON RFC-RF2 ON RF1 RF2 ALL OFF 0.1 and 1 dB Input Compression Point, Vdd = 5V, Linear 0.1 and 1 dB Input Compression Point, Vdd = 3V, Linear 40 35 INPUT COMPRESSION (dBm) INPUT COMPRESSION (dBm) 5 FREQUENCY (GHz) FREQUENCY (GHz) 35 30 25 20 15 30 25 20 15 0 1 2 3 4 5 FREQUENCY (GHz) 0.1 dB Compression Point 1dB Compression Point 6 0 1 2 3 4 5 6 FREQUENCY (GHz) 0.1 dB Compression Point 1 dB Compression Point [1] RFC is reflective in “all off” state. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz 0.1 and 1 dB Input Compression Point, Vdd = 5V 0.1 and 1 dB Input Compression Point, Vdd = 3V INPUT COMPRESSION (dBm) INPUT COMPRESSION (dBm) 35 35 30 25 20 15 0.01 0.1 30 25 20 15 0.01 1 0.1 FREQUENCY (GHz) in log scale 1 FREQUENCY (GHz) in log scale 0.1 dB Compression Point 1 dB Compression Point 0.1 dB Compression Point 1 dB Compression Point Input Third Order Intercept Point, Vdd = 5V, Linear Input Third Order Intercept Point, Vdd = 3V, Linear 60 60 55 55 IP3 (dBm) IP3 (dBm) SWITCHES - SPDT - SMT 40 50 45 50 45 40 40 0 1 2 3 4 5 6 0 1 2 3 6 Input Third Order Intercept Point, Vdd = 3V 60 60 55 55 IP3 (dBm) IP3 (dBm) Input Third Order Intercept Point, Vdd = 5V 50 45 50 45 0.1 1 FREQUENCY (GHz) in log scale +25C +85C -40C 3 5 +25C +85C -40C +25C +85C -40C 40 0.01 4 FREQUENCY (GHz) FREQUENCY (GHz) 40 0.01 0.1 1 FREQUENCY (GHz) in log scale +25C +85C -40C For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz Absolute Maximum Ratings Bias Voltage (Vdd) 7V Control Voltage (Vctl, EN) -1V to Vdd +1V RF Input Power * Through Path 3V/5V Termination Path 3V/5V Channel Temperature 31 / 33 dBm 26.5 dBm Vdd (V) Idd (Typ.) (mA) 3 1.2 5 1.3 150 °C Continuous Pdiss (T = 85 °C) (derate 14.9 mW/°C for through path, and 6.9 mW/°C for termination path above 85 °C) Through Path Termination Path Digital Control Voltages 0.969 W 0.451 W Thermal Resistance (channel to package bottom) Through Path Termination Path 67.1 °C/W 144.2°C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A * The RF input power is quite lower than the breakdown power levels. Hence, the only concern with this product is the thermal limit. State Bias Condition Low 0 to +0.8 Vdc @ <1 µA Typical High +2.0 to +5.0 Vdc @ 40 µA Typical Truth Table Control Input Signal Path State Vctl EN RFC - RF1 Low Low OFF RFC - RF2 ON High Low ON OFF Low High OFF OFF High High OFF OFF SWITCHES - SPDT - SMT Bias Voltage & Current ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz SWITCHES - SPDT - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC849ALP4CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H849A XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz Pin Descriptions Function Description 1 Vdd Supply Voltage. 2 Vctl Control input. See truth and control voltage tables. 3, 9, 12 RFC, RF1, RF2 These pins are DC coupled and matched to 50 Ohms. Blocking capacitors are required. 4, 6, 7, 8, 13, 14, 15, 16 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 5 EN Enable. See truth and control voltage tables. 10, 11 GND Package bottom must also be connected to PCB RF ground. Interface Schematic SWITCHES - SPDT - SMT Pin Number Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6 HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz SWITCHES - SPDT - SMT Evaluation PCB List of Materials for Evaluation PCB EV1HMC849ALP4C [1] Item Description J1 - J3 PC Mount SMA RF Connector J4 - J8 DC Pin C1 - C4 100 pF Capacitor, 0402 Pkg. U1 HMC849ALP4CE SPDT Switch PCB [2] 106965 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR 7 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC849ALP4CE v00.1013 HIGH ISOLATION SPDT NON-REFLECTIVE SWITCH, DC - 6 GHz SWITCHES - SPDT - SMT Notes: For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8