PDF Data Sheet Rev. A

16-Bit, Isolated Sigma-Delta Modulator,
LVDS Interface
AD7405
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VDD1
VDD2
AD7405
MCLKIN+
BUF
CLK
DECODER
CLK
ENCODER
(5MHz TO
20MHz)
MCLKIN–
REF
VIN+
MDAT+
Σ-Δ ADC
VIN–
DATA
ENCODER
DATA
DECODER
MDAT–
GND2
GND1
12536-001
5 MHz to 20 MHz external clock input rate
16 bits, no missing codes
Signal-to-noise ratio (SNR): 88 dB typical
Effective number of bits (ENOB): 14.2 bits typical
Typical offset drift vs. temperature: 1.6 µV/°C
Low voltage differential signaling (LVDS) interface
On-board digital isolator
On-board reference
Full-scale analog input voltage range: ±320 mV
−40°C to + 125°C operating temperature range
High common-mode transient immunity: >25 kV/µs
16-lead, wide-body SOIC_IC, with increased creepage
package
Safety and regulatory approvals
UL recognition
5000 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice 5A
VDE Certificate of Conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
Maximum working insulation voltage (VIORM): 1250 VPEAK
Figure 1.
APPLICATIONS
Shunt current monitoring
AC motor controls
Power and solar inverters
Wind turbine inverters
Data acquisition systems
Analog-to-digital and opto-isolator replacements
GENERAL DESCRIPTION
The AD74051 is a high performance, second-order, Σ-Δ modulator
that converts an analog input signal into a high speed, single-bit
LVDS data stream, with on-chip digital isolation based on
Analog Devices, Inc., iCoupler® technology. The AD7405 operates
from a 4.5 V to 5.5 V (VDD1) power supply and accepts a
differential input signal of ±250 mV (±320 mV full-scale). The
differential input is ideally suited to shunt voltage monitoring in
high voltage applications where galvanic isolation is required.
The analog input is continuously sampled by a high performance
analog modulator, and converted to a ones density digital output
stream with a data rate of up to 20 MHz. The original information
1
can be reconstructed with an appropriate digital filter to achieve
88 dB SNR at 78.1 kSPS. The LVDS input/output can use a 3 V
to 5.5 V supply (VDD2).
The LVDS interface is digitally isolated. The LVDS interface
technology, combined with monolithic transformer technology,
means the on-chip isolation provides outstanding performance
characteristics, superior to alternatives such as optocoupler
devices. The AD7405 device is offered in a 16-lead, wide-body
SOIC_IC package and has an operating temperature range of
−40°C to +125°C.
Protected by U.S. Patents 5,952,849; 6,873,065; and 7,075,329.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD7405
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Terminology .................................................................................... 12
Applications ....................................................................................... 1
Theory of Operation ...................................................................... 13
Functional Block Diagram .............................................................. 1
Circuit Information.................................................................... 13
General Description ......................................................................... 1
Analog Input ............................................................................... 13
Revision History ............................................................................... 2
Differential Inputs ...................................................................... 14
Specifications..................................................................................... 3
Low Voltage Differential Signaling (LVDS) Interface ........... 14
Timing Specifications .................................................................. 4
Applications Information .............................................................. 15
Package Characteristics ............................................................... 5
Current Sensing Applications ................................................... 15
Insulation and Safety Related Specifications ............................ 5
Voltage Sensing Applications .................................................... 15
Regulatory Information ............................................................... 5
Input Filter .................................................................................. 16
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Insulation
Characteristics .............................................................................. 6
Digital Filter ................................................................................ 16
Absolute Maximum Ratings............................................................ 7
Insulation Lifetime ..................................................................... 19
ESD Caution .................................................................................. 7
Outline Dimensions ....................................................................... 20
Pin Configuration and Function Descriptions ............................. 8
Ordering Guide .......................................................................... 20
Grounding and Layout .............................................................. 19
Typical Performance Characteristics ............................................. 9
REVISION HISTORY
11/14—Rev. 0 to Rev. A
Change to Figure 1 ........................................................................... 1
Changes to Table 7 ............................................................................ 7
Changes to Ordering Guide .......................................................... 20
9/14—Revision 0: Initial Version
Rev. A | Page 2 of 20
Data Sheet
AD7405
SPECIFICATIONS
VDD1 = 4.5 V to 5.5 V, VDD2 = 3 V to 5.5 V, VIN+ = −250 mV to +250 mV, VIN− = 0 V, TA = −40°C to +125°C, fMCLKIN 1 = 5 MHz to 20 MHz, tested
with sinc3 filter, 256 decimation rate, as defined by Verilog code, unless otherwise noted. All voltages are relative to their respective ground.
Table 1.
Parameter
STATIC PERFORMANCE
Resolution
Integral Nonlinearity 2
Differential Nonlinearity2
Offset Error2
Offset Drift vs. Temperature
Symbol
Min
Gain Error Drift vs. VDD1
ANALOG INPUT
Input Voltage Range
SINAD
Signal-to-Noise Ratio2
Total Harmonic Distortion2
Peak Harmonic or Spurious Noise2
Effective Number of Bits2
SNR
THD
SFDR
ENOB
±0.8
±0.8
±1.2
95
60
+320
+250
−200 to +300
±45
0.05
±0.01
14
DC Leakage Current
Input Capacitance
DYNAMIC SPECIFICATIONS
Signal-to-Noise-and-Distortion Ratio2
2
±12
±0.99
±0.75
3.8
3.1
−320
−250
Input Common-Mode Voltage Range
Dynamic Input Current
1
±2
±0.2
1.6
1.3
50
±0.2
±0.2
±0.2
65
40
±0.6
Gain Error Drift vs. Temperature
Power Dissipation
Max
16
INL
DNL
Offset Drift vs. VDD1
Gain Error2
Noise Free Code Resolution2
ISOLATION TRANSIENT IMMUNITY2
LVDS I/O (ANSI-644)
Differential Output Voltage
Common-Mode Output Voltage
Differential Input Voltage
Common-Mode Input Voltage
POWER REQUIREMENTS
VDD1
VDD2
IDD1
IDD2
Typ
±50
±0.6
Unit
Test Conditions/Comments
Bits
LSB
LSB
mV
µV/°C
µV/°C
µV/V
% FSR
% FSR
% FSR
ppm/°C
µV/°C
mV/V
Filter output truncated to 16 bits
mV
mV
mV
µA
µA
µA
pF
Guaranteed no missing codes to 16 bits
0°C to 85°C
fMCLKIN = 16 MHz
fMCLKIN = 20 MHz, TA = −40°C to +85°C
fMCLKIN = 20 MHz
Full-scale range
For specified performance
VIN+ = ±250 mV, VIN− = 0 V
VIN+ = 0 V, VIN− = 0 V
VIN+ = 1 kHz
VOD
VOCM
VID
VICM
81
83
86
13.1
13.4
14
25
247
1125
150
800
87
87
88
−96
−97
14.2
14.2
dB
dB
dB
dB
dB
Bits
Bits
Bits
kV/µs
30
360
1260
4.5
3
30
18
13
264
208
For fMCLKIN > 16 MHz, mark space ratio is 48/52 to 52/48, and VDD1 = 5 V ± 5%.
See the Terminology section.
Rev. A | Page 3 of 20
454
1375
650
1575
mV
mV
mV
mV
5.5
5.5
36
22
15
319
248
V
V
mA
mA
mA
mW
mW
−40°C to +85°C
−40°C to +85°C
RL = 100 Ω
RL = 100 Ω
VDD1 = 5.5 V
VDD2 = 5.5 V
VDD2 = 3.3 V
VDD1 = VDD2 = 5.5 V
VDD1 = 5.5 V, VDD2 = 3.3 V
AD7405
Data Sheet
TIMING SPECIFICATIONS
VDD1 = 4.5 V to 5.5 V, VDD2 = 3 V to 5.5 V, TA = −40°C to +125°C, unless otherwise noted. Sample tested during initial release to ensure
compliance. It is recommended to read the MDAT signal on the MCLKIN+ rising edge.
Table 2.
Parameter 1
fMCLKIN
Limit at TMIN, TMAX
5
20
Unit
MHz minimum
MHz maximum
30
40
ns maximum
ns maximum
10
10
ns minimum
ns minimum
0.45 × tMCLKIN
0.48 × tMCLKIN
ns minimum
ns minimum
0.45 × tMCLKIN
0.48 × tMCLKIN
ns minimum
ns minimum
Description
Master clock input frequency
t1
Data access time after MCLKIN+ rising edge
VDD2 = 4.5 V to 5.5 V
VDD2 = 3 V to 3.6 V
Data hold time after MCLKIN+ rising edge
VDD2 = 4.5 V to 5.5 V
VDD2 = 3 V to 3.6V
Master clock low time
fMCLKIN ≤ 16 MHz
16 MHz < fMCLKIN ≤ 20 MHz
Master clock high time
fMCLKIN ≤ 16 MHz
16 MHz < fMCLKIN ≤ 20 MHz
t2
t3
t4
Sample tested during initial release to ensure compliance.
t4
MCLKIN–
MCLKIN+
t1
t2
MDAT–
MDAT+
Figure 2. Data Timing
Rev. A | Page 4 of 20
t3
12536-002
1
Data Sheet
AD7405
PACKAGE CHARACTERISTICS
Table 3.
Parameter
Resistance (Input to Output) 1
Capacitance (Input to Output)1
IC Junction to Ambient Thermal Resistance
1
Symbol
RI-O
CI-O
θJA
Min
Typ
1012
2.2
45
Max
Unit
Ω
pF
°C/W
Test Conditions/Comments
f = 1 MHz
Thermocouple located at center of package underside,
test conducted on 4-layer board with thin traces
The device is considered a 2-terminal device: Pin 1 to Pin 8 are shorted together, and Pin 9 to Pin 16 are shorted together.
INSULATION AND SAFETY RELATED SPECIFICATIONS
Table 4.
Parameter
Input to Output Momentary Withstand Voltage
Minimum External Air Gap (Clearance)
Symbol
VISO
L(I01)
Value
5000 min
8.3 min 1, 2
Unit
V
mm
Minimum External Tracking (Creepage)
L(I02)
8.3 min1
mm
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
0.034 min
>400
II
mm
V
Test Conditions/Comments
1 minute duration
Measured from input terminals to output
terminals, shortest distance through air
Measured from input terminals to output
terminals, shortest distance path along body
Distance through insulation
DIN IEC 112/VDE 0303 Part 1 3
Material Group (DIN VDE 0110, 1/89, Table I)3
In accordance with IEC 60950-1 guidelines for the measurement of creepage and clearance distances for a pollution degree of 2 and altitudes ≤2000 meters.
Consideration must be given to pad layout to ensure the minimum required distance for clearance is maintained.
3
CSA CTI rating for the AD7405 is >600 V and a Material Group I isolation group.
1
2
REGULATORY INFORMATION
Table 5.
UL 1
Recognized under 1577
Component Recognition
Program1
5000 V rms Isolation Voltage
Single Protection
File E214100
CSA
Approved under CSA Component Acceptance Notice 5A
VDE 2
Certified according to DIN V VDE V 0884-10
(VDE V 0884-10):2006-122
Basic insulation per CSA 60950-1-07 and IEC 60950-1,
830 V rms (1173 VPEAK) maximum working voltage 3
Reinforced insulation per CSA 60950-1-07 and
IEC 60950-1, 415 V rms (586 VPEAK) maximum working
voltage3
Reinforced insulation per IEC 60601-1, 250 V rms
(353 VPEAK) maximum working voltage
File 205078
Reinforced insulation per DIN V VDE V 0884-10
(VDE V 0884-10):2006-12, 1250 VPEAK
File 2471900-4880-0001
In accordance with UL 1577, each AD7405 is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (current leakage detection limit = 15 µA).
In accordance with DIN V VDE V 0884-10, each AD7405 is proof tested by applying an insulation test voltage of ≥ 2344 VPEAK for 1 second (partial discharge detection limit = 5 pC).
3
Rating is calculated for a pollution degree of 2 and a Material Group III. The AD7405 RI-16-2 package material is rated by CSA to a CTI of >600 V and, therefore,
Material Group I.
1
2
Rev. A | Page 5 of 20
AD7405
Data Sheet
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by
means of protective circuits.
Table 6.
Description
INSTALLATION CLASSIFICATION PER DIN VDE 0110
For Rated Mains Voltage ≤300 V rms
For Rated Mains Voltage ≤450 V rms
For Rated Mains Voltage ≤600 V rms
For Rated Mains Voltage ≤1000 V rms
CLIMATIC CLASSIFICATION
POLLUTION DEGREE (DIN VDE 0110, TABLE 1)
MAXIMUM WORKING INSULATION VOLTAGE
INPUT TO OUTPUT TEST VOLTAGE, METHOD B1
VIORM × 1.875 = VPR, 100% Production Test, tm = 1 Second, Partial Discharge < 5 pC
INPUT TO OUTPUT TEST VOLTAGE, METHOD A
After Environmental Test Subgroup 1
VIORM × 1.6 = VPR, tm = 60 Seconds, Partial Discharge < 5 pC
After Input and/or Safety Test Subgroup 2/ Safety Test Subgroup 3
VIORM × 1.2 = VPR, tm = 60 Seconds, Partial Discharge < 5 pC
HIGHEST ALLOWABLE OVERVOLTAGE (TRANSIENT OVERVOLTAGE, tTR = 10 Seconds)
SURGE ISOLATION VOLTAGE
1.2 µs Rise Time, 50 µs, 50% Fall Time
SAFETY LIMITING VALUES (MAXIMUM VALUE ALLOWED IN THE EVENT OF A FAILURE, SEE Figure 3)
Case Temperature
Side 1 (PVDD1) and Side 2 (PVDD2) Power Dissipation
INSULATION RESISTANCE AT TS, VIO = 500 V
Symbol
Characteristic
Unit
VIORM
I to IV
I to IV
I to IV
I to IV
40/105/21
2
1250
VPEAK
2344
VPEAK
2000
VPEAK
1500
8000
12000
VPEAK
VPEAK
VPEAK
VPEAK
150
2.78
>109
°C
W
Ω
VPD(M)
VPR(M)
VIOTM
VIOSM
TS
PSO
RIO
3
2
1
0
0
50
100
150
AMBIENT TEMPERATURE (°C)
200
12536-003
SAFE OPERATING POWER (W)
4
Figure 3. Thermal Derating Curve, Dependence of Safety Limiting Values
with Case Temperature per DIN V VDE V 0884-10
Rev. A | Page 6 of 20
Data Sheet
AD7405
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. All voltages are relative to
their respective ground.
Table 7.
Parameter
VDD1 to GND1
VDD2 to GND2
Analog Input Voltage to GND1
Digital Input Voltage to GND2
Output Voltage to GND2
Input Current to Any Pin Except Supplies1
Operating Temperature Range
Storage Temperature Range
Junction Temperature
Pb-Free Temperature, Soldering
Reflow
ESD
FICDM2
HBM3
Rating
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−1 V to VDD1 + 0.3 V
−0.3 V to VDD2 + 0.5 V
−0.3 V to VDD2 + 0.3 V
±10 mA
−40°C to +125°C
−65°C to +150°C
150°C
Table 8. Maximum Continuous Working Voltage1
Parameter
AC Voltage
Bipolar Waveform
Unipolar Waveform
DC Voltage
1
Max (VPEAK)
Constraint
1250
20-year minimum
lifetime (VDE approved
working voltage)
20-year minimum
lifetime
20-year minimum
lifetime
1250
1250
Refers to continuous voltage magnitude imposed across the isolation barrier.
ESD CAUTION
260°C
2 kV
±1250 V
±4000 V
Transient currents of up to 100 mA do not cause silicon controlled rectifier (SCR)
to latch up.
JESD22-C101; RC Network: 1 Ω, Cpkg; Class: IV.
3
ESDA/JEDEC JS-001-2011; RC Network: 1.5 kΩ, 100 pF; Class: 3A.
1
2
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. A | Page 7 of 20
AD7405
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VDD1 1
16 GND2
VIN+ 2
GND1 4
NIC 5
15 NIC
AD7405
14 VDD2
13 MCLKIN+
TOP VIEW
(Not to Scale) 12 MCLKIN–
NIC 6
11 MDAT+
VDD1 7
10 MDAT–
GND1 8
9
GND2
NOTES
1. NIC = NOT INTERNALLY CONNECTED. CONNECT
TO VDD1 , GND1, OR LEAVE FLOATING.
12536-004
VIN– 3
Figure 4. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
1, 7
Mnemonic
VDD1
2
3
4, 8
5, 6, 15
9, 16
10, 11
VIN+
VIN−
GND1
NIC
GND2
MDAT−,
MDAT+
MCLKIN−,
MCLKIN+
VDD2
12, 13
14
Description
Supply Voltage, 4.5 V to 5.5 V. This pin is the supply voltage for the isolated side of the AD7405 and is relative to
GND1. For device operation, connect the supply voltage to both Pin 1 and Pin 7. Decouple each supply pin to
GND1 with a 10 µF capacitor in parallel with a 1 nF capacitor.
Positive Analog Input.
Negative Analog Input. Normally connected to GND1.
Ground 1. This pin is the ground reference point for all circuitry on the isolated side.
Not Internally Connected. Connect to VDD1, GND1, or leave floating.
Ground 2. This pin is the ground reference point for all circuitry on the nonisolated side.
LVDS Data Outputs. The conversion data is output serially on these pins.
LVDS Clock Inputs. Conversion results are shifted out on the rising edge of MCLKIN+.
Supply Voltage, 3 V to 5.5 V. This pin is the supply voltage for the nonisolated side and is relative to GND2.
Decouple this supply to GND2 with a 100 nF capacitor.
Rev. A | Page 8 of 20
Data Sheet
AD7405
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VDD1 = 5 V, VDD2 = 5 V, VIN+ = −250 mV to +250 mV, VIN− = 0 V, fMCLKIN = 20 MHz, using a sinc3 filter with a 256 oversampling
ratio (OSR), unless otherwise noted.
0
0
200mV p-p SINE WAVE ON VDD1
1nF DECOUPLING
fIN = 1kHz
SNR = 88.6dB
SINAD = 88.3dB
THD = –100.5dB
–20
–20
–40
MAGNITUDE (dB)
PSRR (dB)
–40
–60
MCLKIN = 20MHz
MCLKIN = 10MHz
–80
–60
–80
–100
–120
–100
0
200
400
600
800
SUPPLY RIPPLE FREQUENCY (kHz)
1000
–160
12536-005
–120
0
5
10
15
20
25
30
FREQUENCY (kHz)
Figure 5. PSRR vs. Supply Ripple Frequency
12536-008
–140
Figure 8. Typical Fast Fourier Transform (FFT)
1.0
0
SHORTED INPUTS
200mV p-p SINE WAVE ON INPUTS
–20
0.8
0.6
DNL ERROR (LSB)
CMRR (dB)
–40
MCLKIN = 20MHz, SINC3 DECIMATION RATE = 256
MCLKIN = 10MHz, SINC3 DECIMATION RATE = 256
MCLKIN = 20MHz, UNFILTERED
MCLKIN = 10MHz, UNFILTERED
–60
–80
0.4
0.2
0
–0.2
–0.4
–100
–0.6
–120
100
1000
–1.0
RIPPLE FREQUENCY (kHz)
0
10
86
0.6
84
0.4
INL ERROR (LSB)
0.8
82
78
76
= 4.5V
= 5.0V
= 5.5V
= 4.5V
= 5.0V
= 5.5V
–0.6
–0.8
ANALOG INPUT FREQUENCY (Hz)
50
60
0
–0.2
72
1k
60
0.2
74
70
100
50
–0.4
10k
–1.0
12536-007
SINAD (dB)
1.0
88
80
40
Figure 9. Typical DNL Error
90
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
30
CODE (k)
Figure 6. CMRR vs. Common-Mode Ripple Frequency
16MHz MCLKIN,
16MHz MCLKIN,
16MHz MCLKIN,
20MHz MCLKIN,
20MHz MCLKIN,
20MHz MCLKIN,
20
0
10
20
30
40
CODE (k)
Figure 10. Typical INL Error
Figure 7. SINAD vs. Analog Input Frequency
Rev. A | Page 9 of 20
12536-010
10
12536-006
1
12536-009
–0.8
–140
0.1
AD7405
Data Sheet
200
800
MCLKIN = 20MHz
700
150
MCLKIN = 10MHz
VIN+ = VIN– = 0V
1M SAMPLES
692381
100
50
OFFSET (µV)
HITS PER CODE (k)
600
500
400
0
–50
300
–100
200
160941
144470
–150
0
1147
32764
32765
32766
32767
32768
1061
0
32769
32770
CODE
–200
–50
12536-011
0
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
12536-014
100
Figure 14. Offset vs. Temperature
Figure 11. Histogram of Codes at Code Center
10
100
fIN = 1kHz
MCLKIN = 10MHz
MCLKIN = 20MHz
8
6
GAIN ERROR (mV)
SNR AND SINAD (dB)
90
SNR
SINAD
80
4
2
0
–2
–4
70
–6
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
–10
–50
12536-012
60
–50
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 12. SNR and SINAD vs. Temperature
Figure 15. Gain Error vs. Temperature
–60
35
fIN = 1kHz
30
–70
25
THD
SFDR
–90
20
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
15
–100
10
–110
–120
–50
5
–25
0
25
50
75
100
TEMPERATURE (°C)
125
150
Figure 13. THD and SFDR vs. Temperature
0
4.50
4.75
5.00
5.25
–40°C
+25°C
+85°C
+125°C
–40°C
+25°C
+85°C
+125°C
5.50
VDD1 (V)
Figure 16. IDD1 vs. VDD1 at Various Temperatures and Clock Rates
Rev. A | Page 10 of 20
12536-016
IDD1 (mA)
–80
12536-013
THD AND SFDR (dB)
–25
12536-015
–8
Data Sheet
AD7405
17.4
32
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
TA = +125°C
31
DC INPUT
DC INPUT
17.3
IDD2 (mA)
29
28
27
17.2
17.1
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
TA = +125°C
26
–125
0
125
250
VIN+ DC INPUT (mV)
17.0
–250
12536-017
25
–250
–125
0
125
250
VIN+ DC INPUT (mV)
Figure 17. IDD1 vs. VIN+ DC Input at Various Temperatures
12536-019
IDD1 (mA)
30
Figure 19. IDD2 vs. VIN+ DC Input at Various Temperatures
20
60
DC INPUT
18
40
16
14
IIN+ (µA)
10
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 20MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
MCLKIN = 10MHz,
6
4
2
0
3.0
3.5
4.0
4.5
5.0
–40°C
+25°C
+85°C
+125°C
–40°C
+25°C
+85°C
+125°C
5.5
VDD2 (V)
0
MCLKIN = 5MHz
MCLKIN = 10MHz
MCLKIN = 20MHz
–20
–40
Figure 18. IDD2 vs. VDD2 at Various Temperatures and Clock Rates
–60
–320
–240
–160
–80
0
80
160
240
VIN+ DC INPUT (mV)
Figure 20. IIN+ vs. VIN+ DC Input at Various Clock Rates
Rev. A | Page 11 of 20
320
12536-020
8
12536-018
IDD2 (mA)
20
12
AD7405
Data Sheet
TERMINOLOGY
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7405, it is defined as
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are a specified negative full
scale, −250 mV (VIN+ − VIN−), Code 7168 for the 16-bit level,
and a specified positive full scale, +250 mV (VIN+ − VIN−),
Code 58,368 for the 16-bit level.
Offset Error
Offset error is the deviation of the midscale code (32,768 for the
16-bit level) from the ideal VIN+ − VIN− (that is, 0 V).
Gain Error
The gain error includes both positive full-scale gain error and
negative full-scale gain error. Positive full-scale gain error is the
deviation of the specified positive full-scale code (58,368 for the
16-bit level) from the ideal VIN+ − VIN− (250 mV) after the offset
error is adjusted out. Negative full-scale gain error is the
deviation of the specified negative full-scale code (7168 for the
16-bit level) from the ideal VIN+ − VIN− (−250 mV) after the
offset error is adjusted out.
Signal-to-Noise-and-Distortion Ratio (SINAD)
SINAD is the measured ratio of signal-to-noise-and-distortion
at the output of the ADC. The signal is the rms value of the sine
wave, and noise is the rms sum of all nonfundamental signals
up to half the sampling frequency (fS/2), including harmonics,
but excluding dc.
Signal-to-Noise Ratio (SNR)
SNR is the measured signal-to-noise ratio at the output of the
ADC. The signal is the rms amplitude of the fundamental. Noise
is the sum of all nonfundamental signals up to half the sampling
frequency (fS/2), excluding dc.
The ratio is dependent on the number of quantization levels in the
digitization process: the greater the number of levels, the smaller
the quantization noise. The theoretical SNR for an ideal N-bit
converter with a sine wave input is given by
Signal-to-Noise Ratio = (6.02N + 1.76) dB
Therefore, for a 12-bit converter, the SNR is 74 dB.
Isolation Transient Immunity
The isolation transient immunity specifies the rate of rise and
fall of a transient pulse applied across the isolation boundary,
beyond which clock or data is corrupted. The AD7405 was
tested using a transient pulse frequency of 100 kHz.
THD(dB) = 20 log
V2 2 + V3 2 + V4 2 + V5 2 + V6 2
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak.
Effective Number of Bits (ENOB)
ENOB is defined by
ENOB = (SINAD − 1.76)/6.02 bits
Noise Free Code Resolution
Noise free code resolution represents the resolution in bits for
which there is no code flicker. The noise free code resolution
for an N-bit converter is defined as
Noise Free Code Resolution (Bits) = log2(2N/Peak-to-Peak Noise)
The peak-to-peak noise in LSBs is measured with VIN+ = VIN− = 0 V.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output at
±250 mV frequency, f, to the power of a +250 mV peak-to-peak
sine wave applied to the common-mode voltage of VIN+ and VIN−
of frequency, fS, as
CMRR (dB) = 10 log(Pf/PfS)
where:
Pf is the power at frequency, f, in the ADC output.
PfS is the power at frequency, fS, in the ADC output.
Power Supply Rejection Ratio (PSRR)
Variations in power supply affect the full-scale transition but
not the linearity of the converter. PSRR is the maximum change
in the specified full-scale (±250 mV) transition point due to a
change in power supply voltage from the nominal value.
Rev. A | Page 12 of 20
Data Sheet
AD7405
THEORY OF OPERATION
CIRCUIT INFORMATION
The AD7405 isolated Σ-Δ modulator converts an analog input
signal into a high speed (20 MHz maximum), single-bit data
stream; the time average single-bit data from the modulator is
directly proportional to the input signal. Figure 21 shows a
typical application circuit where the AD7405 is used to provide
isolation between the analog input, a current sensing resistor or
shunt, and the digital output, which is then processed by a
digital filter to provide an N-bit word.
ANALOG INPUT
The differential analog input of the AD7405 is implemented
with a switched capacitor circuit. This circuit implements a
second-order modulator stage that digitizes the input signal
into a single-bit output stream. The sample clock (MCLKIN)
provides the clock signal for the conversion process as well as
the output data framing clock. This clock source is external on
the AD7405. The analog input signal is continuously sampled
by the modulator and compared to an internal voltage
reference. A digital stream that accurately represents the
analog input over time appears at the output of the converter
(see Figure 22).
A differential input signal of 0 V ideally results in a differential
stream of alternating 1s and 0s at the MDAT± output pins. This
output is high 50% of the time and low 50% of the time. A
differential input of 250 mV produces a stream of 1s and 0s that
are high 89.06% of the time. A differential input of −250 mV
produces a stream of 1s and 0s that are high 10.94% of the time.
A differential input of 320 mV ideally results in a stream of all
1s. A differential input of −320 mV ideally results in a stream of
all 0s. The absolute full-scale range is ±320 mV, and the specified
full-scale performance range is ±250 mV, as shown in Table 10.
Table 10. Analog Input Range
Analog Input
Positive Full-Scale Value
Positive Specified Performance Input
Zero
Negative Specified Performance Input
Negative Full-Scale Value
Voltage Input (mV)
+320
+250
0
−250
−320
FLOATING
POWER SUPPLY
+400V
NONISOLATED
5V/3V
VDD1
GND1
5.1V
220pF
10Ω
10Ω
RSHUNT
FLOATING
POWER SUPPLY
220pF
Σ-Δ
MOD/
ENCODER
MDAT+
VDD1
MDAT–
DECODER
DECODER
ENCODER
MCLKIN–
GND2
GND1
GATED
DRIVE
CIRCUIT
MDAT
CS
SCLK
MCLKIN+
VIN–
10µF 1nF
SINC3 FILTER*
VDD
VDD2
MCLK
100nF
SDAT
GND
12536-021
*THIS FILTER IS IMPLEMENTED
WITH AN FPGA OR DSP
–400V
Figure 21. Typical Application Circuit
MODULATOR OUTPUT
+FS ANALOG INPUT
–FS ANALOG INPUT
ANALOG INPUT
Figure 22. Analog Input vs. Modulator Output
Rev. A | Page 13 of 20
12536-022
MOTOR
VIN+
AD7405
100Ω
10µF 1nF
100Ω
GATED
DRIVE
CIRCUIT
AD7405
Data Sheet
To reconstruct the original information, this output must be
digitally filtered and decimated. A sinc3 filter is recommended
because it is one order higher than that of the AD7405 modulator,
which is a second-order modulator. If a 256 decimation rate is
used, the resulting 16-bit word rate is 78.1 kSPS, assuming a
20 MHz external clock frequency. See the Digital Filter section
for more detailed information on the sinc filter implementation.
Figure 23 shows the transfer function of the AD7405 relative to
the 16-bit output.
VIN–
300Ω
MCLKIN
φB
1.9pF
φA
1.9pF
φB
φA φB φA φB
12536-024
VIN+
Figure 24. Analog Input Equivalent Circuit
Because the AD7405 samples the differential voltage across its
analog inputs, an input circuit provides low common-mode
noise at each input attaining low noise performance.
65535
58368
LOW VOLTAGE DIFFERENTIAL SIGNALING (LVDS)
INTERFACE
SPECIFIED RANGE
ADC CODE
φA
300Ω
The AD7405 uses an LVDS interface for both the clock input
and the modulator output. The benefits of using LVDS in this
case helps to make the interface between the modulator and the
controller more robust and less susceptible to electromagnetic
interference (EMI) from the surroundings. LVDS also helps to
reduce the EMI emissions associated with high speed digital
signaling. LVDS signals are treated like transmission lines and
must be resistively terminated. The value of the differential
terminating resistor is typically 100 Ω. Place the terminating
resistor as close to the receiver as possible.
7168
–320mV
–250mV
+250mV +320mV
ANALOG INPUT
12536-023
0
Figure 23. Filtered and Decimated 16-Bit Transfer Function
DIFFERENTIAL INPUTS
The analog input to the modulator is a switched capacitor
design. The analog signal is converted into charge by highly
linear sampling capacitors. A simplified equivalent circuit
diagram of the analog input is shown in Figure 24. A signal
source driving the analog input must provide the charge onto
the sampling capacitors every half MCLKIN cycle and settle to the
required accuracy within the next half cycle.
Rev. A | Page 14 of 20
Data Sheet
AD7405
APPLICATIONS INFORMATION
90
CURRENT SENSING APPLICATIONS
85
80
SINAD (dB)
14 -BIT
ENOB
70
13-BIT
ENOB
fIN = 1kHz
MCLKIN = 20MHz
VDD1 = 5V
VDD2 = 5V
TA = 25°C
65
60
0
12-BIT
ENOB
50
100
150
200
250
VIN+ AC INPUT SIGNAL AMPLITUDE (mV)
Figure 25. SINAD vs. VIN+ AC Input Signal Amplitude
1.6
DC INPUT
100k SAMPLES PER DATA POINT
1.4
1.2
RMS NOISE (LSB)
The shunt resistor (RSHUNT) values used in conjunction with the
AD7405 are determined by the specific application requirements
in terms of voltage, current, and power. Small resistors minimize
power dissipation, whereas low inductance resistors prevent any
induced voltage spikes, and good tolerance devices reduce
current variations. The final values chosen are a compromise
between low power dissipation and accuracy. Higher value
resistors use the full performance input range of the ADC, thus
achieving maximum SNR performance. Low value resistors
dissipate less power but do not use the full performance input
range. The AD7405, however, delivers excellent performance,
even with lower input signal levels, allowing low value shunt
resistors to be used while maintaining system performance.
11-BIT
ENOB
12536-025
Choosing RSHUNT
To choose a suitable shunt resistor, first determine the current
through the shunt. The shunt current for a 3-phase induction
motor can be expressed as
I RMS
75
MCLKIN = 5MHz
MCLKIN = 10MHz
MCLKIN = 20MHz
1.0
0.8
0.6
0.4
0.2
0
–320
PW
=
1.73 × V × EF × PF
–240
–160
–80
0
80
160
240
320
VIN+ DC INPUT SIGNAL AMPLITUDE (mV)
12536-026
The AD7405 is ideally suited for current sensing applications
where the voltage across a shunt resistor (RSHUNT) is monitored.
The load current flowing through an external shunt resistor
produces a voltage at the input terminals of the AD7405. The
AD7405 provides isolation between the analog input from the
current sensing resistor and the digital outputs. By selecting the
appropriate shunt resistor value, a variety of current ranges can
be monitored.
Figure 26. RMS Noise vs. VIN+ DC Input Signal Amplitude
where:
IRMS is the motor phase current (A rms).
PW is the motor power (Watts).
V is the motor supply voltage (V ac).
EF is the motor efficiency (%).
PF is the power efficiency (%).
To determine the shunt peak sense current, ISENSE, consider the
motor phase current and any overload that may be possible in
the system. When the peak sense current is known, divide the
voltage range of the AD7405 (±250 mV) by the peak sense
current to yield a maximum shunt value.
If the power dissipation in the shunt resistor is too large, the
shunt resistor can be reduced and less of the ADC input range can
be used. Figure 25 shows the SINAD performance characteristics
and the ENOB of resolution for the AD7405 for different input
signal amplitudes. Figure 26 shows the rms noise performance
for dc input signal amplitudes. The AD7405 performance at
lower input signal ranges allows smaller shunt values to be used
while still maintaining a high level of performance and overall
system efficiency.
RSHUNT must be able to dissipate the I2R power losses. If the
power dissipation rating of the resistor is exceeded, its value
may drift or the resistor may be damaged, resulting in an open
circuit. This open circuit can result in a differential voltage
across the terminals of the AD7405, in excess of the absolute
maximum ratings. If ISENSE has a large, high frequency
component, choose a resistor with low inductance.
VOLTAGE SENSING APPLICATIONS
The AD7405 can also be used for isolated voltage monitoring.
For example, in motor control applications, it can be used to
sense the bus voltage. In applications where the voltage being
monitored exceeds the specified analog input range of the
AD7405, a voltage divider network can be used to reduce the
voltage being monitored to the required range.
Rev. A | Page 15 of 20
AD7405
Data Sheet
INPUT FILTER
DIGITAL FILTER
In a typical application, where voltage is being measured across
a shunt resistor, connect the AD7405 directly across the shunt
resistor with a simple RC low-pass filter on each input.
The output of the AD7405 is a continuous LVDS digital bit stream.
To reconstruct the original input signal information, this output
bit stream needs to be digitally filtered and decimated. A sinc
filter is recommended due to its simplicity. A sinc3 filter is
recommended because it is one order higher than that of the
AD7405 modulator, which is a second-order modulator. The type
of filter selected, the decimation rate, and the modulator clock used
determines the overall system resolution and throughput rate. The
higher the decimation rate, the greater the system accuracy, as
illustrated in Figure 30. However, there is a trade-off between
accuracy and throughput rate and, therefore, higher decimation
rates result in lower throughput solutions. Note that for a given
bandwidth requirement, a higher MCLKIN frequency can allow
higher decimation rates to be used, resulting in higher SNR
performance.
The recommended circuit configuration for driving the
differential inputs to achieve best performance is shown in
Figure 27. An RC low-pass filter is placed on both the analog
input pins. Recommended values for the resistors and capacitors
are 10 Ω and 220 pF, respectively. If possible, equalize the
source impedance on each analog input to minimize offset.
C
R
VIN+
AD7405
R
12536-027
VIN–
100
fIN = 1kHz
90
Figure 27. RC Low-Pass Filter Input Network
80
70
SNR (dB)
The input filter configuration for the AD7405 is not limited to
the low-pass structure shown in Figure 27. The differential RC
filter configuration shown in Figure 28 also achieves excellent
performance. Recommended values for the resistors and
capacitor are 22 Ω and 47 pF, respectively.
R
VIN–
SINC1
SINC2
SINC3
SINC4
10
0
10
Figure 28. Differential RC Filter Input Network
Figure 29 compares the typical performance for the input filter
structures outlined in Figure 27 and Figure 28 for different
resistor and capacitor values.
95
fIN = 1kHz
90
100
1000
DECIMATION RATE
Figure 30. SNR vs. Decimation Rate for Different Sinc Filter Orders
A sinc3 filter is recommended for use with the AD7405. This
filter can be implemented on a field programmable gate array
(FPGA) or a digital signal processor (DSP).
Equation 1 describes the transfer function of a sinc filter.
85
 1 (1 − Z −DR ) 

H (z ) = 
−1 
 DR (1 − Z ) 
80
SNR (dB)
40
20
12536-028
AD7405
C
R
75
N
(1)
where DR is the decimation rate and N is the sinc filter order.
70
The throughput rate of the sinc filter is determined by the
modulator clock and the decimation rate selected.
65
LOW PASS, 10Ω, 220pF
DIFFERENTIAL, 22Ω, 47pF
DIFFERENTIAL, 22Ω, 10nF
Throughput =
100
DECIMATION RATE
1000
12536-029
55
50
10
50
30
VIN+
60
60
12536-030
C
Figure 29. SNR vs. Decimation Rate for Different Filter Structures for Different
Resistor and Capacitor Values
MCLK
DR
(2)
where MCLK is the modulator clock frequency
As the decimation rate increases, the data output size from the
sinc filter increases. The output data size is expressed
in Equation 3. The 16 most significant bits are used to return a
16-bit result.
Data size = N × log2 DR
Rev. A | Page 16 of 20
(3)
Data Sheet
AD7405
Z = one sample delay MCLKOUT = modulators
conversion bit rate */
MCLKIN
Throughput
Rate (kHz)
625
312.5
156.2
78.1
39.1
Output Data
Size (Bits)
15
18
21
24
27
Filter
Response (kHz)
163.7
81.8
40.9
20.4
10.2
The following Verilog code provides an example of a sinc3 filter
implementation on a Xilinx® Spartan®-6 FPGA. Note that the
data is read on the positive clock edge. It is recommended to
read in the data on the positive clock edge. The code is
configurable to accommodate decimation rates from 32 to 4096.
module dec256sinc24b
(
input mclk1, /* used to clk filter */
input reset, /* used to reset filter */
input mdata1, /* input data to be filtered
*/
output reg [15:0] DATA, /* filtered output
*/
output reg data_en,
input [15:0] dec_rate
);
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
[36:0]
ACC3+
+
always @ (negedge mclk1, posedge reset)
begin
if (reset)
begin
/* initialize acc registers on reset
*/
acc1 <= 37'd0;
acc2 <= 37'd0;
acc3 <= 37'd0;
end
else
begin
/*perform accumulation process */
acc1 <= acc1 + ip_data1;
acc2 <= acc2 + acc1;
acc3 <= acc3 + acc2;
end
end
/*decimation stage (MCLKOUT/WORD_CLK) */
always @ (posedge mclk1, posedge reset)
begin
if (reset)
word_count <= 16'd0;
else
begin
ip_data1;
acc1;
acc2;
acc3;
acc3_d2;
diff1;
diff2;
diff3;
diff1_d;
diff2_d;
if ( word_count == dec_rate 1 )
word_count <= 16'd0;
else
word_count <= word_count
+ 16'b1;
end
end
always @ ( posedge mclk1, posedge reset )
begin
if ( reset )
word_clk <= 1'b0;
else
begin
if ( word_count == dec_rate/2 1 )
word_clk <= 1'b1;
else if ( word_count ==
dec_rate - 1 )
word_clk <= 1'b0;
end
end
reg [15:0] word_count;
reg word_clk;
reg enable;
/*Perform the Sinc
always @ (mdata1)
if(mdata1==0)
ip_data1 <=
/* change 0
complement */
else
ip_data1 <=
+
Figure 31. Accumulator
/* Data is read on positive clk edge */
reg
reg
reg
reg
reg
reg
reg
reg
reg
reg
Z
Z
Z
+
Table 11. Sinc3 Filter Characteristics for 20 MHz MCLKIN
Decimation
Ratio (DR)
32
64
128
256
512
ACC2+
ACC1+
IP_DATA1
12536-031
For a sinc3 filter, the −3 dB filter response point can be derived
from the filter transfer function, Equation 1, and is 0.262 times
the throughput rate. The filter characteristics for a third-order
sinc3 filter are summarized in Table 11.
action*/
37'd0;
to a -1 for twos
37'd1;
/*Accumulator (Integrator)
Perform the accumulation (IIR) at the speed
of the modulator.
/*Differentiator (including decimation
stage)
Perform the differentiation stage (FIR) at a
lower speed.
Rev. A | Page 17 of 20
AD7405
Data Sheet
Z = one sample delay WORD_CLK = output word
rate */
+
ACC3
DIFF1
+
–
DIFF2
+
–
Z–1
Z–1
12536-032
Z–1
DIFF3
–
WORD_CLK
Figure 32. Differentiator
always @ (posedge word_clk, posedge reset)
begin
if(reset)
begin
acc3_d2 <= 37'd0;
diff1_d <= 37'd0;
diff2_d <= 37'd0;
diff1 <= 37'd0;
diff2 <= 37'd0;
diff3 <= 37'd0;
end
else
begin
end
diff1 <= acc3 - acc3_d2;
diff2 <= diff1 - diff1_d;
diff3 <= diff2 - diff2_d;
acc3_d2 <= acc3;
diff1_d <= diff1;
diff2_d <= diff2;
end
end
/* Clock the Sinc output into an output
register
WORD_CLK = output word rate */
DATA
12536-033
WORD_CLK
DIFF3
16'd256:begin
DATA <= (diff3[24:8] ==
17'h10000) ? 16'hFFFF : diff3[23:8];
end
16'd512:begin
DATA <= (diff3[27:11] ==
17'h10000) ? 16'hFFFF : diff3[26:11];
end
16'd1024:begin
DATA <= (diff3[30:14] ==
17'h10000) ? 16'hFFFF : diff3[29:14];
end
16'd2048:begin
DATA <= (diff3[33:17] ==
17'h10000) ? 16'hFFFF : diff3[32:17];
end
16'd4096:begin
DATA <= (diff3[36:20] ==
17'h10000) ? 16'hFFFF : diff3[35:20];
end
default:begin
DATA <= (diff3[24:8] ==
17'h10000) ? 16'hFFFF : diff3[23:8];
end
endcase
Figure 33. Clocking Sinc3 Output into an Output Register
always @ ( posedge word_clk )
begin
case ( dec_rate )
16'd32:begin
DATA <= (diff3[15:0] ==
16'h8000) ? 16'hFFFF : {diff3[14:0], 1'b0};
end
16'd64:begin
DATA <= (diff3[18:2] ==
17'h10000) ? 16'hFFFF : diff3[17:2];
end
16'd128:begin
DATA <= (diff3[21:5] ==
17'h10000) ? 16'hFFFF : diff3[20:5];
end
/* Synchronize Data Output*/
always@ ( posedge mclk1, posedge reset )
begin
if ( reset )
begin
data_en <= 1'b0;
enable <= 1'b1;
end
else
begin
if ( (word_count == dec_rate/2
- 1) && enable )
begin
data_en <= 1'b1;
enable <= 1'b0;
end
else if ( (word_count ==
dec_rate - 1) && ~enable )
begin
data_en <= 1'b0;
enable <= 1'b1;
end
else
data_en <= 1'b0;
end
end
endmodule
Rev. A | Page 18 of 20
Data Sheet
AD7405
•
The value that ensures at least a 20-year lifetime of
continuous use.
The maximum VDE approved working voltage.
Note that the lifetime of the AD7405 varies according to the
waveform type imposed across the isolation barrier. The
iCoupler insulation structure is stressed differently, depending
on whether the waveform is bipolar ac, unipolar ac, or dc.
Figure 34, Figure 35, and Figure 36 illustrate the different
isolation voltage waveforms.
INSULATION LIFETIME
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of the
voltage waveform applied across the insulation. In addition to
the testing performed by the regulatory agencies, Analog
Devices carries out an extensive set of evaluations to determine
the lifetime of the insulation structure within the AD7405.
Analog Devices performs accelerated life testing using voltage
levels higher than the rated continuous working voltage.
Acceleration factors for several operating conditions are
determined. These factors allow calculation of the time to
failure at the actual working voltage. The values shown in Table 8
summarize the peak voltage for 20 years of service life for a
bipolar, ac operating condition and the maximum VDE
approved working voltages.
These tests subjected the AD7405 to continuous cross isolation
voltages. To accelerate the occurrence of failures, the selected
Rev. A | Page 19 of 20
RATED PEAK VOLTAGE
12536-034
Minimize series resistance in the analog inputs to avoid any
distortion effects, especially at high temperatures. If possible,
equalize the source impedance on each analog input to minimize
offset. To reduce offset drift, check for mismatch and thermocouple
effects on the analog input printed circuit board (PCB) tracks.
•
0V
Figure 34. Bipolar AC Waveform, 50 Hz or 60 Hz
RATED PEAK VOLTAGE
12536-035
It is recommended to decouple the VDD1 supply with a 10 µF
capacitor in parallel with a 1 nF capacitor to GND1. Decouple
Pin 1 and Pin 7 individually. Decouple the VDD2 supply with a
100 nF value to GND2. In applications involving high commonmode transients, minimize board coupling across the isolation
barrier. Furthermore, design the board layout so that any
coupling that occurs equally affects all pins on a given
component side. Failure to ensure equal coupling can cause
voltage differentials between pins to exceed the absolute
maximum ratings of the device, thereby leading to latch-up or
permanent damage. Place any decoupling used as close to the
supply pins as possible.
test voltages were values exceeding those of normal use. The
time to failure values of these units were recorded and used to
calculate the acceleration factors. These factors were then used
to calculate the time to failure under the normal operating
conditions. The values shown in Table 8 are the lesser of the
following two values:
0V
Figure 35. Unipolar AC Waveform, 50 Hz or 60 Hz
RATED PEAK VOLTAGE
12536-036
GROUNDING AND LAYOUT
0V
Figure 36. DC Waveform
AD7405
Data Sheet
OUTLINE DIMENSIONS
12.85
12.75
12.65
1.93 REF
16
9
7.60
7.50
7.40
10.51
10.31
10.11
8
PIN 1
MARK
2.64
2.54
2.44
2.44
2.24
0.30
0.20
0.10
COPLANARITY
0.1
0.71
0.50
0.31
0.25 BSC
GAGE
PLANE
45°
SEATING
PLANE
1.27 BSC
1.01
0.76
0.51
0.46
0.36
COMPLIANT TO JEDEC STANDARDS MS-013-AC
0.32
0.23
8°
0°
11-15-2011-A
1
Figure 37. 16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Wide Body
(RI-16-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD7405BRIZ
AD7405BRIZ-RL
AD7405BRIZ-RL7
EVAL-AD7405FMCZ
EVAL-SDP-CH1Z
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
16-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Evaluation Board
System Demonstration Platform
Z = RoHS Compliant Part.
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12536-0-11/14(A)
Rev. A | Page 20 of 20
Package
Option
RI-16-2
RI-16-2
RI-16-2