Micropower Quad-Channel Digital Isolators ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 General-purpose, low power multichannel isolation 1 MHz, low power peripheral interface (SPI) 4 mA to 20 mA loop process controls GENERAL DESCRIPTION The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM14471 are micropower, 4-channel digital isolators based on the Analog Devices, Inc., iCoupler® technology. Combining high speed, complementary metal oxide semiconductor (CMOS) and monolithic air core transformer technologies, these isolation components provide outstanding performance characteristics superior to the alternatives, such as optocoupler devices. As shown in Figure 3, in standard operating mode, when ENx = 0 (internal refresh enabled), the current per channel is less than 10 μA. When ENx = 1 (internal refresh disabled), the current per channel drops to less than 1 μA. The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM1447 family of quad 2.5 kV digital isolation devices are packaged in a small 16-lead QSOP and 20-lead SSOP, freeing almost 70% of board space compared to isolators packages in wide body SOIC packages. ADuM144x QSOP 16 VDD2 15 GND2 VIA 3 ENCODE DECODE 14 VOA VIB 4 ENCODE DECODE 13 VOB VIC/VOC 5 ENCODE DECODE 12 VOC/VIC VID/VOD 6 ENCODE DECODE 11 VOD/VID EN1 7 10 EN2 GND1 8 9 GND2 Figure 1. VDD1 1 ADuM144x GND1 2 20 VDD2 19 GND2 VIA 3 ENCODE DECODE 18 VOA VIB 4 ENCODE DECODE 17 VOB VIC/VOC 5 ENCODE DECODE 16 VOC/VIC VID/VOD 6 ENCODE DECODE 15 VOD/VID EN1 7 14 EN2 NIC 8 13 NIC NIC 9 12 NIC GND1 10 11 GND2 Figure 2. The devices withstand high isolation voltages and meet regulatory requirements, such as UL and CSA standards. In addition to the space savings, the ADuM1440/ADuM1441/ADuM1442/ ADuM1445/ADuM1446/ADuM1447 operate with supplies as low as 2.25 V. Despite the low power consumption, all models of the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 provide low, pulse width distortion at <8 ns. In addition, every model has an input glitch filter to protect against extraneous noise disturbances. 1000 100 10 ENx = 0 ENx = 1 1 0.1 0.1 1 10 100 1000 10000 DATA RATE (kbps) 11845-001 APPLICATIONS VDD1 1 GND1 2 CURRENT PER CHANNE L (µA) Ultralow power operation 3.3 V operation (typical) 5.6 μA per channel quiescent current, refresh enabled 0.3 μA per channel quiescent current, refresh disabled 148 μA/Mbps per channel typical dynamic current 2.5 V operation (typical) 3.1 μA per channel quiescent current, refresh enabled 0.1 μA per channel quiescent current, refresh disabled 117 μA/Mbps per channel typical dynamic current Small, 16-lead QSOP and 20-Lead SSOP Bidirectional communication Up to 2 Mbps data rate (NRZ) High temperature operation: 125°C High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals UL 1577 component recognition program 2500 V rms for 1 minute per UL 1577 QSOP package 3750V rms for 1 minute per UL 1577 SSOP package CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 565 VPEAK QSOP package VIORM = 849 VPEAK SSOP package 11845-002 FUNCTIONAL BLOCK DIAGRAMS FEATURES 11845-102 Data Sheet Figure 3. Typical Total Supply Current per Channel (VDDx = 3.3 V) 1 Protected by U.S. Patents 5,952,849, 6,873,065, 7,075,329, 6,262,600. Other patents pending. Rev. D Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2013–2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Recommended Operating Conditions .................................... 11 Applications ....................................................................................... 1 Absolute Maximum Ratings ......................................................... 12 General Description ......................................................................... 1 ESD Caution................................................................................ 12 Functional Block Diagrams ............................................................. 1 Pin Configurations and Function Descriptions ......................... 13 Revision History ............................................................................... 2 Typical Performance Characteristics ........................................... 16 Specifications..................................................................................... 3 Applications Information .............................................................. 19 Electrical Characteristics—3.3 V Operation ............................ 3 Printed Circuit Board (PCB) Layout ....................................... 19 Electrical Characteristics—2.5 V Operation ............................ 5 Propagation Delay-Related Parameters ................................... 19 Electrical Characteristics—VDD1 = 3.3 V, VDD2 = 2.5 V Operation....................................................................................... 7 DC Correctness ............................................................................ 19 Electrical Characteristics—VDD1 = 2.5 V, VDD2 = 3.3 V Operation....................................................................................... 8 Power Consumption .................................................................. 21 Package Characteristics ............................................................... 9 Regulatory Information ............................................................... 9 Insulation and Safety Related Specifications .......................... 10 Magnetic Field Immunity............................................................. 20 Insulation Lifetime ..................................................................... 21 Outline Dimensions ....................................................................... 23 Ordering Guide .......................................................................... 24 DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Insulation Characteristics ............................................................................ 10 REVISION HISTORY 4/15—Rev. C to Rev. D Change to General Description Section ........................................ 1 4/15—Rev. B to Rev. C Changes to Regulatory Information Section ................................ 9 3/15—Rev. A to Rev. B Changes to Features Section and Figure 3..................................... 1 Changes to Table 12 .......................................................................... 9 Changes to Table 13 and Table 14 ................................................ 10 Updated Outline Dimensions ....................................................... 23 Changes to Ordering Guide .......................................................... 24 3/14—Rev. 0 to Rev. A Added SSOP Package ......................................................... Universal Changes to Features Section, Added Figure 2, Renumbered Sequentially ................................................................1 Changes to Output Voltage Logic High Parameter, Table 3 ........4 Added Table 15, Renumbered Sequentially; Changes to Figure 4 ............................................................................................ 11 Change to Supply Voltages (VDD1, VDD2) Parameter, Table 17 ........ 12 Added Figure 6; Changes to Table 20 .......................................... 13 Added Figure 8; Changes to Table 21 .......................................... 14 Added Figure 10, Changes to Table 22 ........................................ 15 Added Figure 30 ............................................................................. 19 Changes to Power Consumption Section; Added Table 23 ...... 21 Added Figure 27 ............................................................................. 23 Changes to Ordering Guide .......................................................... 24 10/13—Revision 0: Initial Version Rev. D | Page 2 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 SPECIFICATIONS ELECTRICAL CHARACTERISTICS—3.3 V OPERATION All typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.3 V. Minimum/maximum specifications apply over the entire recommended operating range of 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF, and CMOS signal levels, unless otherwise noted. Table 1. Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Change vs. Temperature Minimum Pulse Width Pulse-Width Distortion Propagation Delay Skew1 Channel Matching Codirectional Opposing Direction 1 Symbol Min tPHL, tPLH PW PWD tPSK Typ 80 200 Max Unit Test Conditions/Comments 2 180 Within pulse-width distortion (PWD) limit 50% input to 50% output 8 10 Mbps ns ps/°C ns ns ns 10 15 ns ns 500 tPSKCD tPSKOD Within PWD limit |tPLH − tPHL| tPSK is the magnitude of the worst-case difference in tPHL and tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. Table 2. Parameter SUPPLY CURRENT ADuM1440/ADuM1445 ADuM1441/ADuM1446 ADuM1442/ADuM1447 Symbol IDD1 IDD2 IDD1 IDD2 IDD1 IDD2 Min Typ Max Unit 732 492 672 552 612 612 1000 750 900 900 900 900 µA µA µA µA µA µA Rev. D | Page 3 of 24 Test Conditions/Comments 2 Mbps, no load ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet Table 3. For All Models Parameter DC SPECIFICATIONS Input Threshold Logic High Logic Low Output Voltages Logic High Logic Low Input Current per Channel Input Switching Thresholds Positive Threshold Voltage Negative Going Threshold Input Hysteresis Undervoltage Lockout, VDD1 or VDD2 Supply Current per Channel Quiescent Current Input Supply Output Supply Input (Refresh Off ) Output (Refresh Off ) Dynamic Supply Current Input Output AC SPECIFICATIONS Output Rise Time/Fall Time Common-Mode Transient Immunity2 Refresh Rate 1 2 Symbol Min VIH VIL 0.7 VDDx1 VOH VDDx1 − 0.1 VDDx1 − 0.4 VOL II −1 Typ 3.3 3.1 0.0 0.2 +0.01 Max Unit 0.3 VDDx1 V V 0.1 0.4 +1 V V V V µA VT+ VT− ΔVT UVLO 1.8 1.2 0.6 1.5 IDDI (Q) IDDO (Q) IDDI (Q) IDDO (Q) 4.8 0.8 0.12 0.13 IDDI (D) IDDO (D) 88 60 µA/Mbps µA/Mbps 2 40 ns kV/µs 14 kbps tR/tF |CM| fr 25 Test Conditions/Comments IOUTx = −20 µA, VIx = VIxH IOUTx = −4 mA, VIx = VIxH IOUTx = 20 µA, VIx = VIxL IOUTx = 4 mA, VIx = VIxL 0 V ≤ VIx ≤ VDDx1 V V V V 10 3.3 µA µA µA µA ENX low ENX low ENX high ENX high 10% to 90% VIx = VDDx1, VCM = 1000 V, transient magnitude = 800 V VDDx = VDD1 or VDD2. |CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining VOUT > 0.8 VDDx. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. Rev. D | Page 4 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 ELECTRICAL CHARACTERISTICS—2.5 V OPERATION All typical specifications are at TA = 25°C, VDD1 = VDD2 = 2.5 V. Minimum/maximum specifications apply over the entire recommended operating range of 2.25 V ≤ VDD1 ≤ 2.75 V, 2.25 V ≤ VDD2 ≤ 2.75 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF, and CMOS signal levels, unless otherwise noted. Table 4. Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Change vs. Temperature Pulse-Width Distortion Minimum Pulse Width Propagation Delay Skew1 Channel Matching Codirectional Opposing Direction 1 Symbol Min tPHL, tPLH PWD PW tPSK Typ 112 280 Max Unit Test Conditions/Comments 2 180 Within PWD limit 50% input to 50% output 10 Mbps ns ps/°C ns ns ns 10 30 ns ns 12 500 tPSKCD tPSKOD |tPLH − tPHL| Within PWD limit tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. Table 5. Parameter SUPPLY CURRENT ADuM1440/ADuM1445 ADuM1441/ADuM1446 ADuM1442/ADuM1447 Symbol IDD1 IDD2 IDD1 IDD2 IDD1 IDD2 Min Typ Max Unit 623 337 552 409 480 480 800 500 750 750 750 750 µA µA µA µA µA µA Rev. D | Page 5 of 24 Test Conditions/Comments 2 Mbps, no load ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet Table 6. For All Models Parameter DC SPECIFICATIONS Input Threshold Logic High Logic Low Output Voltages Logic High Logic Low Input Current per Channel Input Switching Thresholds Positive Threshold Voltage Negative Going Threshold Input Hysteresis Undervoltage Lockout, VDD1 or VDD2 Supply Current per Channel Quiescent Current Input Supply Output Supply Input (Refresh Off ) Output (Refresh Off ) Dynamic Supply Current Input Output AC SPECIFICATIONS Output Rise Time/Fall Time Common-Mode Transient Immunity2 Refresh Rate 1 2 Symbol Min VIH VIL 0.7 VDDx1 VOH VDDx1 − 0.1 VDDx1 − 0.4 VOL II −1 Typ 2.5 2.35 0.0 0.1 +0.01 Max Unit 0.3 VDDx1 V V 0.1 0.4 +1 V V V V µA VT+ VT− ΔVT UVLO 1.5 1.0 0.5 1.5 IDDI (Q) IDDO (Q) IDDI (Q) IDDO (Q) 2.6 0.5 0.05 0.05 IDDI (D) IDDO (D) 76 41 µA/Mbps µA/Mbps 2 40 ns kV/µs 14 kbps tR/tF |CM| fr 25 Test Conditions/Comments IOx = −20 µA, VIx = VIxH IOx = −4 mA, VIx = VIxH IOx = 20 µA, VIx = VIxL IOx = 4 mA, VIx = VIxL 0 V ≤ VIx ≤ VDDx1 V V V V 3.3 1.8 µA µA µA µA ENX low ENX low ENX high ENX high 10% to 90% VIx = VDDx1, VCM = 1000 V, transient magnitude = 800 V VDDx = VDD1 or VDD2. |CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining VOUT > 0.8 VDDx. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. Rev. D | Page 6 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 ELECTRICAL CHARACTERISTICS—VDD1 = 3.3 V, VDD2 = 2.5 V OPERATION All typical specifications are at TA = 25°C, VDD1 = 3.3 V, and.VDD2 = 2.5 V. Minimum/maximum specifications apply over the entire recommended operating range of 3.0 V ≤ VDD1 ≤ 3.6 V, 2.25 V ≤ VDD2 ≤ 2.75 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF, and CMOS signal levels, unless otherwise noted. For dc specifications and ac specifications, see Table 3 for Side 1 and see Table 6 for Side 2. Table 7. Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Side 1 to Side 2 Side 2 to Side 1 Change vs. Temperature Pulse-Width Distortion Pulse Width Propagation Delay Skew1 Channel Matching Codirectional Opposing Direction 1 Symbol Min tPHL, tPLH tPHL, tPLH PWD PW tPSK Typ 84 120 280 Max Unit Test Conditions/Comments 2 Mbps Within PWD limit 180 180 50% input to 50% output 50% input to 50% output 10 ns ns ps/°C ns ns ns 10 60 ns ns 12 500 tPSKCD tPSKOD |tPLH − tPHL| Within PWD limit tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. Table 8. Parameter SUPPLY CURRENT ADuM1440/ADuM1445 ADuM1441/ADuM1446 ADuM1442/ADuM1447 Symbol IDD1 IDD2 IDD1 IDD2 IDD1 IDD2 Min Typ Max Unit 732 337 672 409 612 480 1000 750 900 750 900 750 µA µA µA µA µA µA Rev. D | Page 7 of 24 Test Conditions/Comments 2 Mbps, no load ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet ELECTRICAL CHARACTERISTICS—VDD1 = 2.5 V, VDD2 = 3.3 V OPERATION All typical specifications are at TA = 25°C, VDD1 = 2.5, and VDD2 = 3.3 V. Minimum/maximum specifications apply over the entire recommended operating range of 2.25 V ≤ VDD1 ≤ 2.75 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF, and CMOS signal levels, unless otherwise noted. For dc specifications and ac specifications, see Table 6 for Side 1 and see Table 3 for Side 2. Table 9. Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Side 1 to Side 2 Side 2 to Side 1 Change vs. Temperature Pulse-Width Distortion Pulse Width Propagation Delay Skew1 Channel Matching Codirectional Opposing Direction 1 Symbol Min tPHL, tPLH tPHL, tPLH PWD PW tPSK Typ 120 84 200 Max Unit Test Conditions/Comments 2 Mbps Within PWD limit 180 180 50% input to 50% output 50% input to 50% output 10 ns ns ps/°C ns ns ns 10 60 ns ns 12 500 tPSKCD tPSKOD |tPLH − tPHL| Within PWD limit tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. Table 10. Parameter SUPPLY CURRENT ADuM1440/ADuM1445 ADuM1441/ADuM1446 ADuM1442/ADuM1447 Symbol IDD1 IDD2 IDD1 IDD2 IDD1 IDD2 Min Typ Max Unit 623 492 552 552 480 612 1000 750 750 900 750 900 µA µA µA µA µA µA Rev. D | Page 8 of 24 Test Conditions/Comments 2 Mbps, no load ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V ENX = 0 V, VIH = VDD, VIL = 0 V Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 PACKAGE CHARACTERISTICS Table 11. Parameter Resistance (Input-to-Output)1 Capacitance (Input-to-Output)1 Input Capacitance2 IC Junction-to-Ambient Thermal Resistance (QSOP) IC Junction-to-Ambient Thermal Resistance (SSOP) 1 2 Symbol RI-O CI-O CI θJA θJA Min Typ 1013 2 4.0 76 50.5 Max Unit Ω pF pF °C/W Test Conditions/Comments °C/W Thermocouple located at center of package underside f = 1 MHz Thermocouple located at center of package underside The device is considered a 2-terminal device: Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together. Input capacitance is from any input data pin to ground. REGULATORY INFORMATION See Table 18 and the Insulation Lifetime section for the recommended maximum working voltages for specific cross-isolation waveforms and insulation levels. Table 12. UL Recognized Under UL 1577 Component Recognition Program1 Single Protection 2500 V RMS Isolation Voltage (RQ-16 Only) 3750 V RMS Isolation Voltage (RS-20 Only) File E214100 CSA Approved under CSA Component Acceptance Notice 5A CSA 60950-1-07+A1+A2 and IEC 60950-1 second edition +A1+A2 QSOP package Basic insulation, 310 V rms maximum working voltage SSOP package Basic insulation at 510 V rms (721 VPEAK) maximum working voltage IEC60601-1 Edition 3.1 250 V (1 means of patient protection (MOPP)) Reinforced insulation at 255 V rms (360 VPEAK) maximum working voltage File 205078 VDE Certified according to DIN V VDE V 0884-10 (VDE V 0884-10):2006-122 QSOP package Reinforced insulation, 565 VPEAK QSOP package SSOP package Reinforced insulation, 849 VPEAK SSOP package File 2471900-4880-0001 In accordance with UL 1577, each ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 is proof tested by applying an insulation test voltage and measuring leakage during final production testing. QSOP package devices are tested at ≥3000 V rms for 1 sec with a current leakage detection limit = 5 μA. SSOP package devices are tested at ≥4500 V rms for 1 sec with a current leakage detection limit = 10 μA. 2 In accordance with DIN V VDE V 0884-10, each ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 is proof tested by applying an insulation test voltage ≥1059 VPEAK for 1 second (partial discharge detection limit = 5 pC). The asterisk (*) marked on the component designates DIN V VDE V 0884-10 approval. 1 Rev. D | Page 9 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet INSULATION AND SAFETY RELATED SPECIFICATIONS Table 13. Parameter Rated Dielectric Insulation Voltage (RQ-16) Rated Dielectric Insulation Voltage (RS-20) Minimum External Tracking and Air Gap, RQ-16 (Creepage and Clearance) L(I02) Value 2500 3750 3.1 Unit V rms V rms mm min Minimum Clearance in the Plane of the Printed Circuit Board, RQ-16 (PCB Clearance) L(I01) 3.8 mm min Minimum External Tracking and Air Gap, RS-20 (Creepage and Clearance) L(I01) 5.1 mm min Minimum Clearance in the Plane of the Printed Circuit Board, RS-20 (PCB Clearance) L(I02) 5.1 mm min CTI 0.017 >400 II mm min V Minimum Internal Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group Symbol Test Conditions/Comments 1-minute duration 1-minute duration Measured from input terminals to output terminals, shortest distance path along package body Measured from input terminals to output terminals, shortest distance through air, line of sight, in the PCB mounting plane Measured from input terminals to output terminals, shortest distance path along package body Measured from input terminals to output terminals, shortest distance through air, line of sight, in the PCB mounting plane Insulation distance through insulation DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS These isolators are suitable for reinforced electrical isolation within the safety limit data only. Maintenance of the safety data is ensured by protective circuits. The asterisk (*) marked on packages denotes DIN V VDE V 0884-10 approval. Table 14. 16-Lead QSOP (RQ-16) Description Installation Classification per DIN VDE 0110 For Rated Mains Voltage ≤ 150 V rms For Rated Mains Voltage ≤ 300 V rms For Rated Mains Voltage ≤ 400 V rms Climatic Classification Pollution Degree per DIN VDE 0110, Table 1 Maximum Working Insulation Voltage Input-to-Output Test Voltage, Method b1 Input-to-Output Test Voltage, Method a After Environmental Tests Subgroup 1 After Input and/or Safety Test Subgroup 2 and Subgroup 3 Highest Allowable Overvoltage Surge Isolation Voltage Safety Limiting Values Case Temperature Total Power Dissipation at 25°C Insulation Resistance at TS Test Conditions/Comments VIORM × 1.875 = Vpd(m), 100% production test, tini = tm = 1 sec, partial discharge < 5 pC VIORM × 1.5 = Vpd(m), tini = 60 sec, tm = 10 sec, partial discharge < 5 pC VIORM × 1.2 = Vpd(m), tini = 60 sec, tm = 10 sec, partial discharge < 5 pC VPEAK = 10 kV, 1.2 µs rise time, 50 µs, 50% fall time Maximum value allowed in the event of a failure (see Figure 4) VIO = 500 V Rev. D | Page 10 of 24 Symbol Characteristic Unit VIORM Vpd(m) I to IV I to III I to II 40/105/21 2 565 1059 VPEAK VPEAK Vpd(m) 847 VPEAK Vpd(m) 678 VPEAK VIOTM VIOSM 4000 6250 VPEAK VPEAK TS IS1 RS 150 1.64 >109 °C W Ω Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Table 15. 20-Lead SSOP (RS-20) Description Installation Classification per DIN VDE 0110 For Rated Mains Voltage ≤ 150 V rms For Rated Mains Voltage ≤ 300 V rms For Rated Mains Voltage ≤ 400 V rms Climatic Classification Pollution Degree per DIN VDE 0110, Table 1 Maximum Working Insulation Voltage Input-to-Output Test Voltage, Method b1 Conditions VIORM × 1.875 = Vpd(m), 100% production test, tini = tm = 1 sec, partial discharge < 5 pC Input-to-Output Test Voltage, Method a After Environmental Tests Subgroup 1 After Input and/or Safety Test Subgroup 2 and Subgroup 3 Highest Allowable Overvoltage Surge Isolation Voltage Safety Limiting Values VIORM × 1.5 = Vpd(m), tini = 60 sec, tm = 10 sec, partial discharge < 5 pC VIORM × 1.2 = Vpd(m),tini = 60 sec, tm = 10 sec, partial discharge < 5 pC VPEAK = 10 kV, 1.2 µs rise time, 50µs, 50% fall time Maximum value allowed in the event of a failure (see Figure 4) Case Temperature Total Power Dissipation at 25°C Insulation Resistance at TS VIO = 500 V 3.0 Unit VIORM Vpd(m) I to IV I to IV I to III 40/105/21 2 849 1592 VPEAK VPEAK Vpd(m) 1273 VPEAK Vpd(m) 1018 VPEAK VIOTM VIOSM 6000 6000 VPEAK VPEAK TS IS1 150 2.5 °C W RS >109 Ω Table 16. 2.5 SAFE LIMITING POWER (W) Characteristic RECOMMENDED OPERATING CONDITIONS SSOP20 Parameter Operating Temperature Supply Voltages1 Input Signal Rise and Fall Times 2.0 QSOP16 1.5 1 1.0 50 100 150 AMBIENT TEMPERATURE (°C) 200 11845-003 0 Symbol TA VDD1, VDD2 Value −40°C to +125°C 2.25 V to 3.6 V 1.0 ms All voltages are relative to their respective grounds. See the DC Correctness section for information on immunity to external magnetic fields. 0.5 0 Symbol Figure 4. Thermal Derating Curve, Dependence of Safety-Limiting Values with Case Temperature per DIN V VDE V 0884-10 Rev. D | Page 11 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 18. Maximum Continuous Working Voltage1 Table 17. Parameter AC Voltage 60 Hz Bipolar Waveform 60 Hz Unipolar Waveform Basic Insulation DC Voltage Basic Insulation Parameter Supply Voltages (VDD1, VDD2) Input Voltages (VIA, VIB ) Output Voltages (VOA, VOB) Average Output Current per Pin1 Side 1 (IO1) Side 2 (IO2) Common-Mode Transients2 Storage Temperature (TST) Range Ambient Operating Temperature (TA) Range 1 2 Rating −0.5 V to +5 V −0.5 V to VDDI + 0.5 V −0.5 V to VDD2 + 0.5 V −10 mA to +10 mA −10 mA to +10 mA −100 kV/µs to +100 kV/µs −65°C to +150°C −40°C to +125°C 1 Value Constraint 565 VPEAK 50-year minimum lifetime 975 VPEAK 50-year minimum lifetime 975 VPEAK 50-year minimum lifetime Refers to continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more details. ESD CAUTION See Figure 4 for maximum safety power values for various temperatures. Refers to common-mode transients across the insulation barrier. Common-mode transients exceeding the absolute maximum ratings can cause latch-up or permanent damage. Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Table 19. Truth Table (Positive Logic) for all Models VIx Input1, 2 H L H L L VDDI State3 Powered Powered Powered Powered Unpowered VDDO State4 Powered Powered Powered Powered Powered ENx Input1 L L H H L VOx Output1 H L H L5 Default L Unpowered Powered H Hold X Powered Unpowered X Z Description Normal operation; data is high and refresh is enabled. Normal operation; data is low and refresh is enabled. Output is high, and refresh is disabled. Output is low, and refresh is disabled. Input unpowered. Outputs are in the default state, high for ADuM1440, ADuM1441, and ADuM1442, and low ADuM1445, ADuM1446, and ADuM1447. Outputs return to input state within 150 µs of VDDI power restoration. See the pin function descriptions (Table 20 through Table 22) for more details. Input unpowered. Outputs are the last state before input power is shut down. Output unpowered. Output pins are in high impedance state. Outputs return to input state within 34 µs of VDDO power restoration. See the pin function descriptions (Table 20 through Table 22) for more details. H = high, L = low, X = don’t care, and Z = high impedance. VIx and VOx refer to the input and output signals of a given channel (A, B, C, or D). 3 VDDI refers to the power supply on the input side of a given channel (A, B, C, or D). 4 VDDO refers to the power supply on the output side of a given channel (A, B, C, or D). 5 Low input must follow a falling edge; otherwise, it can be in the default low state. 1 2 Rev. D | Page 12 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS VDD1 1 20 VDD2 GND11 2 19 GND22 VOA VIA 3 18 VOA VOB VIB 4 17 VOB 12 VOC VIC 5 16 VOC 15 VOD VDD1 1 16 VDD2 GND11 2 15 GND22 14 13 VIA 3 VIB 4 ADuM1440/ ADuM1445 VIC 5 TOP VIEW (Not to Scale) VID 6 11 VOD VID 6 EN1 7 10 EN2 EN1 7 GND11 8 9 GND22 2 AND PIN 8 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND1 IS RECOMMENDED. 2PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED. 11845-004 1PIN ADuM1440/ ADuM1445 TOP VIEW (Not to Scale) 14 EN2 NIC 8 13 NIC NIC 9 12 NIC GND11 10 11 GND22 NIC = NOT INTERNALLY CONNECTED. 2 AND PIN 10 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND1 IS RECOMMENDED. 2PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED. Figure 5. ADuM1440/ADuM1445 QSOP Pin Configuration 11845-104 1PIN Figure 6. ADuM1440/ADuM1445 SSOP Pin Configuration Table 20. ADuM1440/ADuM1445 Pin Function Descriptions1 QSOP Pin No.2 1 SSOP Pin No. 1 Mnemonic VDD1 2, 8 2, 10 GND1 3 4 5 6 7 3 4 5 3 7 VIA VIB VIC VID EN1 9, 15 11, 19 GND2 10 14 EN2 11 12 13 14 16 15 16 17 18 20 VOD VOC VOB VOA VDD2 N/A 8, 9, 12, 13 NC 1 2 Description Supply Voltage for Isolator Side 1 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD1 (Pin 1) and GND1 (Pin 2). Ground 1. Ground reference for Isolator Side 1. Pin 2 and Pin 8 are internally connected, and connecting both to GND1 is recommended. Logic Input A. Logic Input B. Logic Input C. Logic Input D. Refresh/Watchdog Enable 1. Connecting Pin 7 to GND1 enables input/output refresh and watchdog functionality for Side 1, supporting standard iCoupler operation. Tying Pin 7 to VDD1 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for a detailed description of this mode. EN1 and EN2 must be set to the same logic state. Ground 2. Ground reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and connecting both to GND2 is recommended. Refresh/Watchdog Enable 2. Connecting Pin 10 to GND2 enables input/output refresh and watchdog functionality for Side 2, supporting standard iCoupler operation. Tying Pin 10 to VDD2 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for a detailed description of this mode. EN1 and EN2 must be set to the same logic state. Logic Output D. Logic Output C. Logic Output B. Logic Output A. Supply Voltage for Isolator Side 2 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD2 (Pin 16) and GND2 (Pin 15). No Connect. Do not connect to this pin. Reference the AN-1109 Application Note for specific layout guidelines. N/A = not applicable. Rev. D | Page 13 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet VDD1 1 20 VDD2 GND11 2 19 GND22 VDD1 1 16 VDD2 GND11 2 15 GND22 14 VOA VIA 3 18 VOA 13 VOB VIB 4 17 VOB VIA 3 VIB 4 ADuM1441/ ADuM1446 VIC 5 TOP VIEW (Not to Scale) 12 VOC VIC 5 VOD 6 11 VID VOD 6 EN1 7 10 EN2 EN1 7 GND11 8 9 GND22 NIC 8 2 AND PIN 8 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND1 IS RECOMMENDED. 2PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED. 11845-005 1PIN ADuM1441/ ADuM1446 TOP VIEW (Not to Scale) 16 VOC 15 VID 14 EN2 13 NIC NIC 9 12 NIC GND11 10 11 GND22 NIC = NOT INTERNALLY CONNECTED. 2 AND PIN 10 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND1 IS RECOMMENDED. 2PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED. Figure 7. ADuM1441/ADuM1446 QSOP Pin Configuration 11845-108 1PIN Figure 8. ADuM1441/ADuM1446 SSOP Pin Configuration Table 21. ADuM1441/ADuM1446 Pin Function Descriptions1 QSOP Pin No. 2 1 SSOP Pin No. 1 Mnemonic VDD1 2, 8 2, 10 GND1 3 4 5 6 7 3 4 5 3 7 VIA VIB VIC VOD EN1 9, 15 11, 19 GND2 10 14 EN2 11 12 13 14 16 15 16 17 18 20 VID VOC VOB VOA VDD2 N/A 8, 9, 12, 13 NC 1 2 Description Supply Voltage for Isolator Side 1 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD1 (Pin 1) and GND1 (Pin 2). Ground 1. Ground reference for Isolator Side 1. Pin 2 and Pin 8 are internally connected, and connecting both to GND1 is recommended. Logic Input A. Logic Input B. Logic Input C. Logic Output D. Refresh/Watchdog Enable 1. Connecting Pin 7 to GND1 enables input/output refresh and watchdog functionality for Side 1, supporting standard iCoupler operation. Tying Pin 7 to VDD1 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for a detailed description of this mode. EN1 and EN2 must be set to the same logic state. Ground 2. Ground reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and connecting both to GND2 is recommended. Refresh/Watchdog Enable 2. Connecting Pin 10 to GND2 enables input/output refresh and watchdog functionality for Side 2, supporting standard iCoupler operation. Tying Pin 10 to VDD2 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for a detailed description of this mode. EN1 and EN2 must be set to the same logic state. Logic Input D. Logic Output C. Logic Output B. Logic Output A. Supply Voltage for Isolator Side 2 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD2 (Pin 16) and GND2 (Pin 15). No Connect. Do not connect to this pin. Reference the AN-1109 Application Note for specific layout guidelines. N/A = not applicable. Rev. D | Page 14 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 VDD1 1 VIA 3 13 VOB VIB 4 12 VIC VOC 5 VOD 6 11 VID VOD 6 EN1 7 10 EN2 EN1 7 VIB 4 ADuM1442/ ADuM1447 VOC 5 TOP VIEW (Not to Scale) GND11 8 9 GND22 1PIN 2 AND PIN 8 ARE INTERNALLY CONNECTED. CONNECTING BOTH BOTH TO GND2 IS RECOMMENDED. 18 VOA ADuM1442/ ADuM1447 TOP VIEW (Not to Scale) 17 VOB 16 VIC 15 VID 14 EN2 NIC 8 13 NIC NIC 9 12 NIC GND11 10 11845-006 TO GND1 IS RECOMMENDED. 2PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED. CONNECTING 19 GND22 GND11 2 15 GND22 14 VOA VIA 3 20 VDD2 VDD1 1 16 VDD2 GND11 2 11 GND22 NIC = NOT INTERNALLY CONNECTED. 1PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND1 IS RECOMMENDED. 2PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED. Figure 9. ADuM1442/ADuM1447 QSOP Pin Configuration 11845-110 Data Sheet Figure 10. ADuM1442/ADuM1447 SSOP Pin Configuration Table 22. ADuM1442/ADuM1447 Pin Function Descriptions1 QSOP Pin No. 2 1 SSOP Pin No. 1 Mnemonic VDD1 2, 8 2, 10 GND1 3 4 5 6 7 3 4 5 3 7 VIA VIB VOC VOD EN1 9, 15 11, 19 GND2 10 14 EN2 11 12 13 14 16 15 16 17 18 20 VID VIC VOB VOA VDD2 N/A 8, 9, 12, 13 NC 1 2 Description Supply Voltage for Isolator Side 1 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD1 (Pin 1) and GND1 (Pin 2). Ground 1. Ground reference for Isolator Side 1. Pin 2 and Pin 8 are internally connected, and connecting both to GND1 is recommended. Logic Input A. Logic Input B. Logic Output C. Logic Output D. Refresh/Watchdog Enable 1. Connecting Pin 7 to GND1 enables input/output refresh and watchdog functionality for Side 1, supporting standard iCoupler operation. Tying Pin 7 to VDD1 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for detailed description of this mode. EN1 and EN2 must be set to the same logic state. Ground 2. Ground reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and connecting both to GND2 is recommended. Refresh/Watchdog Enable 2. Connecting Pin 10 to GND2 enables input/output refresh and watchdog functionality for Side 2, supporting standard iCoupler operation. Tying Pin 10 to VDD2 disables refresh and watchdog functionality for lowest power operation, see the Applications Information section for a detailed description of this mode. EN1 and EN2 must be set to the same logic state. Logic Input D. Logic Input C. Logic Output B. Logic Output A. Supply Voltage for Isolator Side 2 (2.25 V to 3.6 V). Connect a ceramic bypass capacitor in the 0.01 µF to 0.1 µF range between VDD2 (Pin 16) and GND2 (Pin 15). No Connect. Do not connect to this pin. Reference the AN-1109 Application Note for specific layout guidelines. N/A = not applicable. Rev. D | Page 15 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 15 10 250 5 0 200 0 20 40 150 100 50 VDDx INPUT CURRENT 0 500 1000 1500 2000 DATA RATE (kbps) 0 20 40 60 40 20 VDDx OUTPUT CURRENT 0 1500 1000 500 2000 Figure 14. Current Consumption per Output vs. Data Rate for 3.3 V, ENx = Low Operation CURRENT CONSUMPTION PER INPUT (µA) 160 80 4 2 60 0 50 0 20 40 40 30 20 10 0 500 1000 1500 2000 DATA RATE (kbps) 1.0 120 0.5 100 0 0 5 10 80 60 40 20 VDDx INPUT CURRENT VDDx OUTPUT CURRENT 0 140 0 0 500 1500 1000 2000 DATA RATE (kbps) 11845-011 70 11845-008 CURRENT CONSUMPTION PER OUTPUT (µA) 0 80 DATA RATE (kbps) 90 Figure 15. Current Consumption per Input vs. Data Rate for 2.5 V, ENx = High Operation Figure 12. Current Consumption per Output vs. Data Rate for 2.5 V, ENx = Low Operation 90 350 CURRENT CONSUMPTION PER OUTPUT (µA) 400 15 10 300 5 0 250 0 20 40 200 150 100 50 VDDx INPUT CURRENT 0 500 1000 1500 2000 DATA RATE (kbps) 11845-009 CURRENT CONSUMPTION PER INPUT (µA) 2 100 0 Figure 11. Current Consumption per Input vs. Data Rate for 2.5 V, ENx = Low Operation 0 4 80 1.0 70 0.5 60 0 0 5 10 50 40 30 20 10 VDDx OUTPUT CURRENT 0 0 500 1000 DATA RATE (kbps) 1500 2000 11845-012 0 120 11845-010 300 CURRENT CONSUMPTION PER OUTPUT (µA) 140 11845-007 CURRENT CONSUMPTION PER INPUT (µA) 350 Figure 16. Current Consumption per Output vs. Data Rate for 2.5 V, ENx = High Operation Figure 13. Current Consumption per Input vs. Data Rate for 3.3 V, ENx = Low Operation Rev. D | Page 16 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 300 FALLING RISING 180 1.0 250 160 0.5 0 120 0 5 IDDx CURRENT (µA) 140 10 100 80 60 40 150 100 50 500 1000 1500 2000 DATA RATE (kbps) 0 Figure 17. Current Consumption per Input vs. Data Rate for VDDX = 3.3 V, ENx = High Operation 0.5 1.0 2.0 1.5 2.5 Figure 20. IDDx Current per Input vs. Data Input Voltage for VDDx = 2.5 V 10 9 0.5 100 0 0 5 10 80 60 40 20 8 7 6 5 4 3 2 1 OUTPUT INPUT VDDx OUTPUT CURRENT 500 1000 1500 2000 DATA RATE (kbps) 11845-014 0 0 –40 –20 0 20 40 60 80 100 140 Figure 21. Typical Input and Output Supply Current per Channel vs. Temperature for VDDx = 2.5 V, Data Rate = 100 kbps Figure 18. Current Consumption per Output vs. Data Rate for VDDx = 3.3 V, ENx = High Operation 10 600 FALLING RISING 9 SUPPLY CURRENT/CHANNEL (µA) 500 400 300 200 100 8 7 6 5 4 3 2 0 1 2 3 DATA INPUT VOLTAGE (V) 4 11845-015 1 0 120 TEMPERATURE (°C) 11845-117 SUPPLY CURRENT/CHANNEL (µA) 1.0 120 0 3.0 DATA INPUT VOLTAGE (V) 140 IDDx CURRENT (µA) 0 11845-016 VDDx INPUT CURRENT 0 0 –40 OUTPUT INPUT –20 0 20 40 60 80 TEMPERATURE (°C) 100 120 140 11845-118 0 CURRENT CONSUMPTION PER OUTPUT (µA) 200 20 11845-013 CURRENT CONSUMPTION PER INPUT (µA) 200 Figure 22. Typical Input and Output Supply Current per Channel vs. Temperature for VDDx = 3.3 V, Data Rate = 100 kbps Figure 19. Typical IDDx Current per Input vs. Data Input Voltage for VDDx = 3.3 V Rev. D | Page 17 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 100 Data Sheet 120 100 GLITCH FILTER WIDTH (ns) 80 70 60 50 40 30 20 80 60 40 0 –40 OUTPUT INPUT –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0 2.0 2.5 3.0 3.5 4.0 TRANSMITTER VDDx (V) Figure 23. Typical Input and Output Supply Current per Channel vs. Temperature for VDDx = 2.5 V, Data Rate = 1000 kbps 11845-017 20 10 11845-119 SUPPLY CURRENT/CHANNEL (µA) 90 Figure 26. Typical Glitch Filter Operation Threshold 100 140 120 80 REFRESH PERIOD (µs) SUPPLY CURRENT/CHANNEL (µA) 90 70 60 50 40 30 100 80 60 40 20 20 VDDx = 2.5V VDDx = 3.3V –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0 –40 11845-120 0 –40 OUTPUT INPUT 0 20 40 60 80 100 120 140 TEMPERATURE (°C) Figure 24. Typical Input and Output Supply Current per Channel vs. Temperature for VDDx = 3.3 V, Data Rate = 1000 kbps Figure 27. Typical Refresh Period vs. Temperature for 3.3 V and 2.5 V Operation 140 120 120 100 REFRESH PERIOD (µs) 100 80 60 40 80 60 40 20 20 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0 2.0 2.5 3.0 3.5 VDDx VOLTAGE (V) Figure 28. Typical Refresh Period vs. VDDX Voltage Figure 25. Typical Propagation Delay vs. Temperature for VDDx = 3.3 V or VDDx = 2.5 V Rev. D | Page 18 of 24 4.0 11845-123 0 –40 VDDx = 2.5V VDDx = 3.3V 11845-121 PROPAGATION DELAY (ns) –20 11845-122 10 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 APPLICATIONS INFORMATION INPUT (VIx) The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM1447 digital isolators require no external interface circuitry for the logic interfaces. Power supply bypassing is strongly recommended at both input and output supply pins: VDD1 and VDD2 (see Figure 29). Choose a capacitor value between 0.01 µF and 0.1 µF. The total lead length between both ends of the capacitor and the input power supply pin must not exceed 20 mm. Using proper PCB design choices, the ADuM1440/ADuM1441/ ADuM1442/ADuM1445/ADuM1446/ADuM1447 readily meets CISPR 22 Class A (and FCC Class A) emissions standards, as well as the more stringent CISPR 22 Class B (and FCC Class B) standards in an unshielded environment. Refer to the AN-1109 Application Note, Recommendations for Control of Radiated Emissions with iCoupler Devices, for PCB-related EMI mitigation techniques, including board layout and stack-up issues. VDD2 GND2 VOA VOB VOC/VIC VOD/VID EN2 GND2 NC GND1 VDD2 GND2 VOA VOB VOC/VIC VOD/VID CTRL2 NC/EN2 NC GND2 11845-126 Figure 29. Recommended Printed Circuit Board Layout, QSOP VDD1 GND1 VIA VIB VIC/VOC VID/VOD NC/CTRL1 EN1 tPLH OUTPUT (VOx) tPHL 50% Figure 31. Propagation Delay Parameters Pulse width distortion is the maximum difference between these two propagation delay values and an indication of how accurately the timing of the input signal is preserved. Channel-to-channel matching is the maximum amount of time the propagation delay differs between channels within a single ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ ADuM1447 component. Propagation delay skew is the maximum amount of time the propagation delay differs between multiple ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 components operating under the same conditions. In edge-based systems, it is critical to reject pulses that are too short to be handled by the encode and decode circuits. The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ ADuM1447 implement a glitch filter to reject pulses less than the glitch filter operating threshold. This threshold depends on the operating voltage, as shown in Figure 26. Any pulse shorter than the glitch filter does not pass to the output. When the refresh circuit is enabled, pulses that match the glitch filter width have a small probability of being stretched until corrected by the next refresh cycle, or by the next valid data through that channel. To avoid issues with pulse stretching, observe the minimum pulse width requirements listed in the switching specifications. 11845-018 VDD1 GND1 VIA VIB VIC/VOC VID/VOD EN1 GND1 50% 11845-019 PRINTED CIRCUIT BOARD (PCB) LAYOUT DC CORRECTNESS Figure 30. Recommended Printed Circuit Board Layout, SSOP Standard Operating Mode For applications involving high common-mode transients, it is important to minimize board coupling across the isolation barrier. Furthermore, design the board layout so that any coupling that does occur equally affects all pins on a given component side. Failure to ensure this can cause voltage differentials between pins exceeding the absolute maximum ratings of the device, thereby leading to latch-up or permanent damage. PROPAGATION DELAY-RELATED PARAMETERS These products are optimized for minimum power consumption by eliminating as many internal bias currents as possible. As a result, the timing characteristics are more sensitive to operating voltage and temperature than in standard iCoupler products. Refer to Figure 21 through Figure 28 for the expected variation of these parameters. Propagation delay is a parameter defined as the time it takes a logic signal to propagate through a component. The input-tooutput propagation delay time for a high-to-low transition can differ from the propagation delay time of a low-to-high transition. Positive and negative logic transitions at the isolator input cause narrow (~1 ns) pulses to be sent to the decoder using the transformer. The decoder is bistable and is, therefore, either set or reset by the pulses, indicating input logic transitions. When refresh and watchdog functions are enabled by pulling EN1 and EN2 low, in the absence of logic transitions at the input for more than ~140 µs, a periodic set of refresh pulses indicative of the correct input state is sent to ensure dc correctness at the output. If the decoder receives no internal pulses of more than approximately 200 µs, the input side is assumed unpowered or nonfunctional, in which case, the isolator watchdog circuit forces the output to a default state. The default state is either high as in the ADuM1440, ADuM1441, and ADuM1442 versions, or low as in the ADuM1445, ADuM1446, and ADuM1447 versions. Low Power Operating Mode The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM1447 allow the refresh and watchdog functions to be disabled by pulling EN1 and EN2 to logic high for the lowest power consumption. These control pins must be set to the same value on each side of the component for proper operation. Rev. D | Page 19 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet where: β is magnetic flux density (gauss). rn is the radius of the nth turn in the receiving coil (cm). N is the number of turns in the receiving coil. 1. 2. 3. Given the geometry of the receiving coil in the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 and an imposed requirement that the induced voltage be, at most, 50% of the 0.5 V margin at the decoder, a maximum allowable magnetic field at a given frequency can be calculated. The result is shown in Figure 32. The high on VIA is not automatically transferred to the Side 2 VOA, and there can be a level mismatch that is not corrected until a transition occurs at VIA. After power is stable on each side and a transition occurs on the input of the channel, that channel’s input and output state is correctly matched. This contingency can be addressed in several ways, such as sending dummy data, or toggling refresh on for a short period to force synchronization after turn on. Recommended Input Voltage for Low Power Operation The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM1447 implement Schmitt trigger input buffers so that the devices operate cleanly in low data rate or noisy environments. Schmitt triggers allow a small amount of shoot through current when their input voltage is not approximate to either VDDx or GNDx levels. This is because the two transistors are both slightly on when input voltages are in the middle of the supply range. For many digital devices, this leakage is not a large portion of the total supply current and may not be noticed; however, in the ultralow power ADuM1440/ADuM1441/ADuM1442/ ADuM1445/ADuM1446/ADuM1447, this leakage can be larger than the total operating current of the device and cannot be ignored. To achieve optimum power consumption with the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ ADuM1447, always drive the inputs as near to VDDx or GNDx levels as possible. Figure 19 and Figure 20 illustrate the shoot through leakage of an input; therefore, whereas the logic thresholds of the input are standard CMOS levels, optimum power performance is achieved when the input logic levels are driven within 0.5 V of either VDDx or GNDx levels. MAGNETIC FIELD IMMUNITY The magnetic field immunity of the ADuM1440/ADuM1441/ ADuM1442/ADuM1445/ADuM1446/ADuM1447 is determined by the changing magnetic field, which induces a voltage in the receiving coil of the transformer large enough to either falsely set or reset the decoder. The following analysis defines the conditions under which this can occur. The 3.3 V operating condition of the ADuM1440/ADuM1441/ADuM1442/ ADuM1445/ADuM1446/ADuM1447 is examined because it represents the most typical mode of operation. 1000 100 10 1 0.1 0.01 0.001 1k 10k 10M 100k 1M MAGNETIC FIELD FREQUENCY (Hz) 100M 11845-020 Power is applied to Side 1 A high level is asserted on the VIA input Power is applied to Side 2 MAXIMUM ALLOWABLE MAGNETIC FLUX (kgauss) In this mode, the current consumption of the chip drops to the microamp range. However, be careful when using this mode because dc correctness is no longer guaranteed at startup. For example, if the following sequence of events occurs: Figure 32. Maximum Allowable External Magnetic Flux Density For example, at a magnetic field frequency of 1 MHz, the maximum allowable magnetic field of 0.5 kgauss induces a voltage of 0.25 V at the receiving coil. This is about 50% of the sensing threshold and does not cause a faulty output transition. Similarly, if such an event occurred during a transmitted pulse (and was of the worst-case polarity), it would reduce the received pulse from >1.0 V to 0.75 V, still well above the 0.5 V sensing threshold of the decoder. The preceding magnetic flux density values correspond to specific current magnitudes at given distances from the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 transformers. Figure 33 shows these allowable current magnitudes as a function of frequency for selected distances. As shown, the ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ ADuM1447 are extremely immune and can be affected only by extremely large currents operating at a high frequency very near to the component. For the 1 MHz example noted previously, a 1.2 kA current would have to be placed 5 mm away from the ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ ADuM1447 to affect the operation of the component. The pulses at the transformer output have an amplitude greater than 1.0 V. The decoder has a sensing threshold at about 0.5 V, thus establishing a 0.5 V margin in which induced voltages can be tolerated. The voltage induced across the receiving coil is given by V = (−dβ/dt) ∑ π rn2; n = 1, 2, … , N Rev. D | Page 20 of 24 Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 average data rate, either by bursting data at high speed at a low duty factor or by running low bit rates. If data is burst at high data rates, the part sits quiescent for the majority of the time, at low data rates, the power consumption approaches the quiescent power consumption. Table 23 shows the typical current for an input and output channel pair as well as the total power dissipated for that channel. The total power is summed across both sides of the device, so the power is being drawn from two different supplies. However, it shows how the power depends on the VDD values and the state of the refresh. 100 10 1 0.1 DISTANCE = 5mm DISTANCE = 100mm DISTANCE = 1m 0.01 1k 10M 10k 100k 1M MAGNETIC FIELD FREQUENCY (Hz) 100M 11845-021 MAXIMUM ALLOWABLE CURRENT (kA) 1000 Figure 33. Maximum Allowable Current for Various Current-to-ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Spacings Note that at combinations of strong magnetic field and high frequency, any loops formed by PCB traces can induce error voltages sufficiently large enough to trigger the thresholds of succeeding circuitry. Take care in the layout of such traces to avoid this possibility. Table 23. Typical Total Power Dissipation Per Channel State of Refresh Enabled Disabled Typical Input Channel VDDI IDDI(Q) Typical Output Channel VDDO IDDO(Q) Power/Ch 2.5 V 2.6 µA 2.5 V 0.5 µA 7.8 µW 3.3 V 4.8 µA 3.3 V 0.8 µA 18.5 µW 2.5 V 0.05 µA 2.5 V 0.05 µA 0.3 µW 3.3 V 0.12 µA 3.3 V 0.13 µA 0.8 µW POWER CONSUMPTION INSULATION LIFETIME The supply current at a given channel of the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 isolator is a function of the supply voltage, the data rate of the channel, and the output load of the channel. All insulation structures eventually break down when subjected to voltage stress over a sufficiently long period. The rate of insulation degradation is dependent on the characteristics of the voltage waveform applied across the insulation. In addition to the testing performed by the regulatory agencies, Analog Devices carries out an extensive set of evaluations to determine the lifetime of the insulation structure within the ADuM1440/ ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447. For each input channel, the supply current is given by IDDI = IDDI (Q) f ≤ 0.5 fr IDDI = IDDI (D) × (2f − fr) + IDDI (Q) f > 0.5 fr For each output channel, the supply current is given by IDDO = IDDO (Q) f ≤ 0.5 fr IDDO = (IDDO (D) + (0.5 × 10 ) × CL × VDDO) × (2f − fr) + IDDO (Q) f > 0.5 fr −3 where: IDDI (D), IDDO (D) are the input and output dynamic supply currents per channel (mA/Mbps). IDDI (Q), IDDO (Q) are the specified input and output quiescent supply currents (mA). f is the input logic signal frequency (MHz); it is half the input data rate, expressed in units of Mbps. fr is the input stage refresh rate (Mbps). CL is the output load capacitance (pF). VDDO is the output supply voltage (V). To calculate the total VDD1 and VDD2 supply current, the supply currents for each input and output channel corresponding to VDD1 and VDD2 are calculated and totaled. Figure 11 through Figure 18 show per channel supply currents as a function of data rate for an unloaded output condition. The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ ADuM1446/ADuM1447 devices are intended to operate at an ultralow current. This is achieved by operating the part at a low Analog Devices performs accelerated life testing using voltage levels higher than the rated continuous working voltage. Acceleration factors for several operating conditions are determined. These factors allow calculation of the time to failure at the actual working voltage. The values shown in Table 18 summarize the peak voltage for 50 years of service life for a bipolar ac operating condition and the maximum CSA approved working voltages. In many cases, the approved working voltage is higher than the 50-year service life voltage. Operation at these high working voltages can lead to shortened insulation life, in some cases. The insulation lifetime of the ADuM1440/ADuM1441/ ADuM1442/ADuM1445/ADuM1446/ADuM1447 depends on the voltage waveform type imposed across the isolation barrier. The iCoupler insulation structure degrades at different rates depending on whether the waveform is bipolar ac, unipolar ac, or dc. Figure 34, Figure 35, and Figure 36 illustrate these different isolation voltage waveforms. Bipolar ac voltage is the most stringent environment. The goal of a 50-year operating lifetime under the ac bipolar condition determines the Analog Devices recommended maximum working voltage. In the case of unipolar ac or dc voltage, the stress on the insulation is significantly lower. This allows operation at higher working Rev. D | Page 21 of 24 ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 11845-022 0V Figure 34. Bipolar AC Waveform RATED PEAK VOLTAGE 11845-023 Note that the voltage presented in Figure 35 is shown as sinusoidal for illustration purposes only. It is meant to represent any voltage waveform varying between 0 V and some limiting value. The limiting value can be positive or negative, but the voltage cannot cross 0 V. RATED PEAK VOLTAGE 0V Figure 35. Unipolar AC Waveform RATED PEAK VOLTAGE 11845-024 voltages while still achieving a 50-year service life. The working voltages listed in Table 18 can be applied while maintaining the 50-year minimum lifetime provided the voltage conforms to either the unipolar ac or dc voltage case. Treat any cross-insulation voltage waveform that does not conform to Figure 35 or Figure 36 as a bipolar ac waveform, and limit its peak voltage to the 50-year lifetime voltage value listed in Table 18. 0V Figure 36. DC Waveform Rev. D | Page 22 of 24 Data Sheet Data Sheet ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 OUTLINE DIMENSIONS 0.197 (5.00) 0.193 (4.90) 0.189 (4.80) 16 9 0.158 (4.01) 0.154 (3.91) 0.150 (3.81) 1 8 0.244 (6.20) 0.236 (5.99) 0.228 (5.79) 0.010 (0.25) 0.006 (0.15) 0.069 (1.75) 0.053 (1.35) 0.065 (1.65) 0.049 (1.25) 0.010 (0.25) 0.004 (0.10) COPLANARITY 0.004 (0.10) SEATING PLANE 0.025 (0.64) BSC 8° 0° 0.012 (0.30) 0.008 (0.20) 0.050 (1.27) 0.016 (0.41) 0.020 (0.51) 0.010 (0.25) 0.041 (1.04) REF 09-12-2014-A COMPLIANT TO JEDEC STANDARDS MO-137-AB CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 37. 16-Lead Shrink Small Outline Package [QSOP] (RQ-16) (Dimensions shown in inches and (millimeters) 7.50 7.20 6.90 11 20 5.60 5.30 5.00 1 8.20 7.80 7.40 10 0.65 BSC 0.38 0.22 SEATING PLANE 8° 4° 0° COMPLIANT TO JEDEC STANDARDS MO-150-AE Figure 38. 20-Lead Shrink Small Outline Package [SSOP] (RS-20) Dimensions shown in millimeters Rev. D | Page 23 of 24 0.95 0.75 0.55 060106-A 0.05 MIN COPLANARITY 0.10 0.25 0.09 1.85 1.75 1.65 2.00 MAX ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 Data Sheet ORDERING GUIDE Model1, 2 ADuM1440ARQZ ADuM1441ARQZ ADuM1442ARQZ ADuM1445ARQZ ADuM1446ARQZ ADuM1447ARQZ ADuM1440ARSZ ADuM1441ARSZ ADuM1442ARSZ ADuM1445ARSZ ADuM1446ARSZ ADuM1447ARSZ EVAL-ADUM1441EBZ 1 2 Number of Inputs, VDD1 Side 4 3 2 4 3 2 4 3 2 4 3 2 Number of Inputs, VDD2 Side 0 1 2 0 1 2 0 1 2 0 1 2 Maximum Data Rate (Mbps) 2 2 2 2 2 2 2 2 2 2 2 2 Default Output State High High High Low Low Low High High High Low Low Low Maximum Propagation Delay, 3.3 V (ns) 180 180 180 180 180 180 180 180 180 180 180 180 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Z = RoHS Compliant Part. Tape and reel is available. The addition of the –RL7 suffix indicates that the product is shipped on 7” tape and reel. ©2013–2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D11845-0-4/15(D) Rev. D | Page 24 of 24 Package Description 16-Lead QSOP 16-Lead QSOP 16-Lead QSOP 16-Lead QSOP 16-Lead QSOP 16-Lead QSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP Evaluation Board Package Option RQ-16 RQ-16 RQ-16 RQ-16 RQ-16 RQ-16 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20