MPX IPC Locking Clamp Quick Start Guide (R11/13) (SL-20838)

MPX™ IPC™
Quick-Start Guide
North American Applications
L
MPX IPC (Input Power Cord) – for MPX
PEM™ Variable Capacity Systems ONLY
The MPX IPC is available with various types
of NEMA connectors that permit changing the
input power to a Liebert® MPX™ equipped with
a variable capacity MPX PEM.
The MPX IPC is available in multiple
versions supporting up to 30A single-phase
North American 120VAC and 208VAC and
three‑phase North American 120/208 and
208VAC connections.
• 120VAC – Single-Phase Input /
Output MPXIPC-NXD30XX—30A,
120VAC; NEMA L5-30P Locking plug;
10ft. (3.0m) cord.
• 208VAC – Single‑Phase Input /
Output MPXIPC-NXF30XXX—30A,
208VAC; NEMA L6-30P Locking plug;
10ft. (3.0m) cord.
• 120/208VAC – Single Phase Input /
Output MPXIPC-NXL30XXX—30A,
208/120VAC; NEMA L14-30 Locking
plug; 10ft. (3.0m) cord.
!
Warnings
Before beginning to assemble and
install a Liebert MPX, read and
fully understand all warnings and
cautions in the Liebert MPX user
manual, SL-20820, which can be
downloaded at www.liebert.com
Emerson Network Power strongly
recommends that the MPX PEM
be installed by an individual who
has been properly trained and
qualified to perform electrical
work.
The Liebert MPX contains high
voltage that could cause serious
personal injury or death. The
Liebert MPX must be installed in a
restricted-access location.
• 208VAC – Three Phase Input /
120/208VAC Single-Phase Output
MPXIPC‑NXG30XXX—20A, 120/208VAC, 5-wire; NEMA L21-20P Locking plug;
10ft. (3.0m) cord.
MPXIPC-NXH30XXX—30A,120/208VAC, 5-wire; NEMA L21-30P Locking plug;
10ft. (3.0m) cord.
• 208VAC – Three-Phase Input / 208VAC Single-Phase Output
MPXIPC-NXJ30XXX—30A, 208VAC, 4-wire; NEMA L15-30P Locking plug; 10ft.
(3.0m) cord.
Optional MPX™ IPC™ Locking Clamp
The MPX IPC Locking Clamp is applied to limit removal of the MPX IPC. The standard
MPX IPC allows for quick removal from the MPX PEM™ by opening the connector
latching mechanism. The Locking Clamp reduces the chance of accidental removal of the
MPX IPC—the clamp must be removed before the connector can be opened. The Locking
Clamp is optional and not required for normal Liebert® MPX™ system application.
To attach the MPX IPC Locking Clamp: Spread the retaining tabs to open the clamp.
1. Wrap the clamp around the MPX IPC connector.
2. Press the ridged tongue into the retaining tabs.
3. Spread the retaining tabs to open the clamp.
4. Wrap the clamp around the MPX IPC connector.
5. Press the ridged tongue into the retaining tabs.
Ridged Tongue
Retaining
Tabs
MPX IPC Locking Clamp
Connector inserted in
MPX PEM
MPX IPC Locking Clamp
around Connector
Technical Support / Service
Web Site
www.liebert.com
Monitoring
[email protected]
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
[email protected]
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2013 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
SL-20838_REV1_11-13
Emerson Network Power
Division: Liebert
Web: www.emerson.com
www.EmersonNetworkPower.com