New Product SiA467EDJ www.vishay.com Vishay Siliconix P-Channel 12 V (D-S) MOSFET FEATURES PRODUCT SUMMARY VDS (V) - 12 RDS(on) () (Max.) ID (A)a 0.0130 at VGS = - 4.5 V - 31 0.0145 at VGS = - 3.7 V - 30 0.0195 at VGS = - 2.5 V - 26 0.0400 at VGS = - 1.8 V -7 Qg (Typ.) 29 nC PowerPAK SC-70-6L-Single APPLICATIONS 1 D • Portable Devices such as Smart Phones, Tablet PCs and Mobile Computing 2 D 3 6 - Battery Switch - Load Switch - Power Management G D 5 S D 2.05 mm S • TrenchFET® Power MOSFET • Thermally Enhanced PowerPAK® SC-70 Package - Small Footprint Area - Low On-Resistance • 100 % Rg and UIS Tested • Typ ESD Protection: 5000 V (HBM) • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 S G Marking Code 2.05 mm 4 B1 X Part # code Ordering Information: SiA467EDJ-T1-GE3 (Lead (Pb)-free and Halogen-free) XXX D Lot Traceability and Date code P-Channel MOSFET ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted) Parameter Symbol Limit Drain-Source Voltage VDS - 12 Gate-Source Voltage VGS ±8 TC = 25 °C Continuous Drain Current (TJ = 150 °C) TC = 70 °C TA = 25 °C Continuous Source-Drain Diode Current - 25 ID - 13b, c - 11b, c Single Avalanche Current Single Avalanche Energy IDM TC = 25 °C TA = 25 °C L = 0.1 mH TC = 70 °C TA = 25 °C - 16 IS - 2.9b, c IAS - 11 EAS 5.8 mJ 19 12 PD W 3.5b, c 2.2b, c TA = 70 °C Operating Junction and Storage Temperature Range A - 60 TC = 25 °C Maximum Power Dissipation V - 31 TA = 70 °C Pulsed Drain Current (t = 300 μs) Unit TJ, Tstg - 50 to 150 Soldering Recommendations (Peak Temperature)d, e °C 260 THERMAL RESISTANCE RATINGS Parameter Maximum Junction-to-Ambientb, f Maximum Junction-to-Case (Drain) Symbol Typical Maximum t5s RthJA 28 36 Steady State RthJC 5.3 6.5 Unit °C/W Notes a. TC = 25 °C. b. Surface mounted on 1" x 1" FR4 board. c. t = 5 s. d. See solder profile (www.vishay.com/doc?73257). The PowerPAK SC-70 is a leadless package. The end of the lead terminal is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed and is not required to ensure adequate bottom side solder interconnection. e. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components. f. Maximum under steady state conditions is 80 °C/W. S13-0107-Rev. A, 21-Jan-13 Document Number: 62816 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product SiA467EDJ www.vishay.com Vishay Siliconix SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) Parameter Symbol Test Conditions Min. VDS VGS = 0 V, ID = - 250 μA - 12 Typ. Max. Unit Static Drain-Source Breakdown Voltage VDS/TJ VDS Temperature Coefficient VGS(th) Temperature Coefficient VGS(th)/TJ ID = - 250 μA Gate-Source Threshold Voltage VGS(th) VDS = VGS, ID = - 250 μA Gate-Source Leakage IGSS Zero Gate Voltage Drain Current IDSS On-State Drain Currenta ID(on) Drain-Source On-State Resistancea Forward Transconductancea V - 6.4 - 0.4 -1 VDS = 0 V, VGS = ± 8 V ±2 VDS = 0 V, VGS = ± 4.5 V ± 0.5 VDS = - 12 V, VGS = 0 V -1 VDS = - 12 V, VGS = 0 V, TJ = 55 °C VDS - 5 V, VGS = - 4.5 V RDS(on) gfs mV/°C 2.4 V μA - 10 - 10 A VGS = - 4.5 V, ID = - 5 A 0.0105 0.0130 VGS = - 3.7 V, ID = - 5 A 0.0120 0.0145 VGS = - 2.5 V, ID = - 4 A 0.0155 0.0195 VGS = - 1.8 V, ID = - 2 A 0.0260 0.0400 VGS = - 6 V, ID = - 5 A 31 S Dynamicb Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss Total Gate Charge Qg Gate-Source Charge Qgs Gate-Drain Charge Qgd Gate Resistance Rg Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time 2520 VDS = - 6 V, VGS = 0 V, f = 1 MHz pF 545 VDS = - 6 V, VGS = - 8 V, ID = - 14 A VDS = - 6 V, VGS = - 4.5 V, ID = - 14 A 48 72 29 44 4 VDD = - 6 V, RL = 0.6 ID - 10 A, VGEN = - 4.5 V, Rg = 1 1.8 9 18 25 50 25 50 90 180 tf 50 100 td(on) 10 20 10 20 120 240 45 90 td(off) nC 6.6 f = 1 MHz td(on) tr 570 VDD = - 6 V, RL = 0.6 ID - 10 A, VGEN = - 8 V, Rg = 1 tr td(off) tf ns Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulse Diode Forward Current ISM Body Diode Voltage VSD Body Diode Reverse Recovery Time trr Body Diode Reverse Recovery Charge Qrr Reverse Recovery Fall Time ta Reverse Recovery Rise Time tb TC = 25 °C - 16 - 60 IS = - 10 A, VGS = 0 V IF = - 10 A, dI/dt = 100 A/μs, TJ = 25 °C A - 0.75 - 1.2 V 20 40 ns 7 15 nC 9 11 ns Notes a. Pulse test; pulse width 300 μs, duty cycle 2 %. b. Guaranteed by design, not subject to production testing. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. S13-0107-Rev. A, 21-Jan-13 Document Number: 62816 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product SiA467EDJ www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 10-2 20.00 10-3 12.00 10-4 IGSS - Gate Current (A) IGSS - Gate Current (mA) 16.00 TJ = 25 °C 8.00 10-5 TJ = 150 °C 10-6 TJ = 25 °C 10-7 4.00 10-8 10-9 0.00 0 4 8 12 16 0 4 VGS - Gate-Source Voltage (V) 8 12 16 VGS - Gate-to-Source Voltage (V) Gate Current vs. Gate-Source Voltage Gate Current vs. Gate-to-Source Voltage 20 60 VGS = 5 V thru 3 V VGS = 2.5 V 16 ID - Drain Current (A) ID - Drain Current (A) 50 40 VGS = 2 V 30 20 VGS = 1.5 V 10 12 8 TC = 25 °C TC = 125 °C 4 TC = - 55 °C 0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0.0 1.0 1.5 VGS - Gate-to-Source Voltage (V) Output Characteristics Transfer Characteristics 0.060 2.0 4000 VGS = 1.8 V 3500 0.050 3000 C - Capacitance (pF) RDS(on) - On-Resistance (Ω) 0.5 VDS - Drain-to-Source Voltage (V) 0.040 0.030 VGS = 2.5 V 0.020 Ciss 2500 2000 1500 Coss 1000 VGS = 3.7 V 0.010 Crss 500 VGS = 4.5 V 0.000 0 0 10 20 30 40 50 60 0 2 4 6 8 ID - Drain Current (A) VDS - Drain-to-Source Voltage (V) On-Resistance vs. Drain Current and Gate Voltage Capacitance S13-0107-Rev. A, 21-Jan-13 10 12 Document Number: 62816 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product SiA467EDJ www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 1.4 ID = 14 A RDS(on) - On-Resistance (Normalized) VGS - Gate-to-Source Voltage (V) 8 VDS = 6 V 6 VDS = 3 V 4 VDS = 9.6 V 2 VGS = 4.5 V, 2.5 V 1.3 ID = 5 A VGS = 3.7 V 1.2 VGS = 1.8 V 1.1 1.0 0.9 0 0.8 0 10 20 30 40 50 - 50 - 25 0 Gate Charge 50 75 100 125 150 On-Resistance vs. Junction Temperature 100 0.060 TJ = 150 °C 0.050 RDS(on) - On-Resistance (Ω) IS - Source Current (A) 25 TJ - Junction Temperature (°C) Qg - Total Gate Charge (nC) 10 TJ = 25 °C 1 ID = 5 A 0.040 0.030 TJ = 125 °C 0.020 TJ = 25 °C 0.010 0.1 0.000 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 1 VSD - Source-to-Drain Voltage (V) 0.7 25 0.6 20 Power (W) VGS(th) (V) 30 0.5 ID = 250 μA 10 0.3 5 0.2 25 50 75 100 5 15 0.4 0 4 On-Resistance vs. Gate-to-Source Voltage 0.8 - 25 3 VGS - Gate-to-Source Voltage (V) Soure-Drain Diode Forward Voltage - 50 2 125 150 0 0.001 0.01 0.1 1 Time (s) 10 100 1000 TJ - Temperature (°C) Threshold Voltage S13-0107-Rev. A, 21-Jan-13 Single Pulse Power, Junction-to-Ambient Document Number: 62816 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product SiA467EDJ www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 100 Limited by RDS(on)* 100 µs ID - Drain Current (A) 10 1 ms 1 10 ms 100 ms 10 s 1s 0.1 DC TA = 25 °C BVDSS Limited 0.01 0.1 1 10 100 VDS - Drain-to-Source Voltage (V) * VGS > minimum VGS at which RDS(on) is specified Safe Operating Area, Junction-to-Ambient 35 20 25 Power Dissipation (W) ID - Drain Current (A) 30 20 15 10 15 10 5 5 0 0 0 25 50 75 100 TC - Case Temperature (°C) Current Derating* 125 150 25 50 75 100 125 TC - Case Temperature (°C) 150 Power Derating * The power dissipation PD is based on TJ(max.) = 150 °C, using junction-to-case thermal resistance, and is more useful in settling the upper dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this rating falls below the package limit. S13-0107-Rev. A, 21-Jan-13 Document Number: 62816 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product SiA467EDJ www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 0.1 Notes: 0.05 PDM 0.1 t1 0.02 t2 1. Duty Cycle, D = t1 t2 2. Per Unit Base = RthJA = 80 °C/W 3. TJM - TA = PDMZthJA(t) Single Pulse 0.01 10-4 10-3 4. Surface Mounted 10-2 10-1 1 Square Wave Pulse Duration (s) 10 100 1000 Normalized Thermal Transient Impedance, Junction-to-Ambient Normalized Effective Transient Thermal Impedance 1 0.1 10-4 Duty Cycle = 0.5 0.2 0.1 0.05 0.02 Single Pulse 10-3 10-2 10-1 Square Wave Pulse Duration (s) Normalized Thermal Transient Impedance, Junction-to-Case Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?62816. S13-0107-Rev. A, 21-Jan-13 Document Number: 62816 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information Vishay Siliconix b e PIN1 PIN3 PIN1 PIN2 PIN3 PIN5 K1 E1 E1 K PIN6 K3 D1 D1 K D2 D1 E3 E1 E2 K4 K L PIN2 b e L PowerPAK® SC70-6L PIN6 PIN4 K2 PIN5 K1 K2 BACKSIDE VIEW OF SINGLE PIN4 K2 BACKSIDE VIEW OF DUAL A D C A1 E Notes: 1. All dimensions are in millimeters 2. Package outline exclusive of mold flash and metal burr 3. Package outline inclusive of plating Z z DETAIL Z SINGLE PAD DIM A MILLIMETERS DUAL PAD INCHES MILLIMETERS INCHES Min Nom Max Min Nom Max Min Nom Max Min Nom Max 0.675 0.75 0.80 0.027 0.030 0.032 0.675 0.75 0.80 0.027 0.030 0.032 A1 0 - 0.05 0 - 0.002 0 - 0.05 0 - 0.002 b 0.23 0.30 0.38 0.009 0.012 0.015 0.23 0.30 0.38 0.009 0.012 0.015 C 0.15 0.20 0.25 0.006 0.008 0.010 0.15 0.20 0.25 0.006 0.008 0.010 D 1.98 2.05 2.15 0.078 0.081 0.085 1.98 2.05 2.15 0.078 0.081 0.085 D1 0.85 0.95 1.05 0.033 0.037 0.041 0.513 0.613 0.713 0.020 0.024 0.028 D2 0.135 0.235 0.335 0.005 0.009 0.013 E 1.98 2.05 2.15 0.078 0.081 0.085 1.98 2.05 2.15 0.078 0.081 0.085 E1 1.40 1.50 1.60 0.055 0.059 0.063 0.85 0.95 1.05 0.033 0.037 0.041 E2 0.345 0.395 0.445 0.014 0.016 0.018 E3 0.425 0.475 0.525 0.017 0.019 0.021 e 0.65 BSC 0.026 BSC 0.65 BSC 0.026 BSC K 0.275 TYP 0.011 TYP 0.275 TYP 0.011 TYP K1 0.400 TYP 0.016 TYP 0.320 TYP 0.013 TYP K2 0.240 TYP 0.009 TYP 0.252 TYP 0.010 TYP K3 0.225 TYP 0.009 TYP K4 L 0.355 TYP 0.175 0.275 0.014 TYP 0.375 T 0.007 0.011 0.015 0.175 0.275 0.375 0.007 0.011 0.015 0.05 0.10 0.15 0.002 0.004 0.006 ECN: C-07431 − Rev. C, 06-Aug-07 DWG: 5934 Document Number: 73001 06-Aug-07 www.vishay.com 1 Application Note 826 Vishay Siliconix RECOMMENDED PAD LAYOUT FOR PowerPAK® SC70-6L Single 0.300 (0.012) 0.650 (0.026) 0.350 (0.014) 0.275 (0.011) 0.550 (0.022) 0.475 (0.019) 2.200 (0.087) 1.500 (0.059) 0.870 (0.034) 0.235 (0.009) 0.355 (0.014) 0.350 (0.014) 1 0.650 (0.026) 0.300 (0.012) 0.950 (0.037) Dimensions in mm/(Inches) Return to Index APPLICATION NOTE Document Number: 70486 Revision: 21-Jan-08 www.vishay.com 11 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000