Datasheet No - PD97469 Nov 2, 2009 IR11672AS ADVANCED SMART RECTIFIER TM CONTROL IC Product Summary Features • • • • • • • • • • • • • • • Secondary side high speed SR controller Topology DCM, CrCM flyback and Resonant half-bridge topologies 200V proprietary IC technology VD Max 500KHz switching frequency VOUT Anti-bounce logic and UVLO protection 7A peak turn off drive current Io+ & I o- (typical) Micropower start-up & ultra low quiescent current Turn on Propagation 10.7V gate drive clamp Delay 50ns turn-off propagation delay Vcc range from 11.3V to 20V Turn off Propagation Direct sensing of MOSFET drain voltage Delay Enable function synchronized with MOSFET VDS transition Cycle by Cycle MOT Check Circuit prevents multiple Package Options false trigger GATE pulses Lead-free Compatible with 0.3W Standby, Energy Star, CECP, etc. Flyback, Resonant Half-bridge 200V 10.7V +2A & -7A 60ns (typical) 50ns (typical) Typical Applications • LCD & PDP TV, Telecom SMPS, AC-DC adapters, ATX SMPS, Server SMPS 8-Lead SOIC Typical Connection Diagram Vin Rs Rdc XFM Cdc U1 1 Ci 2 3 RMOT 4 VCC VGATE OVT GND MOT VS EN VD 8 LOAD Cs 7 6 Co 5 Rg IR11671 IR11672AS Rtn Q1 *Please note that this datasheet contains advance information that could change before the product is released to production. www.irf.com © 2009 International Rectifier IR11672AS Table of Contents Page Description 3 Qualification Information 4 Absolute Maximum Ratings 5 Electrical Characteristics 6 Functional Block Diagram 8 Input/Output Pin Equivalent Circuit Diagram 9 Lead Definitions 10 Lead Assignments 10 Application Information and Additional Details 12 Package Details 22 Tape and Reel Details 23 Part Marking Information 24 Ordering Information 25 www.irf.com © 2009 International Rectifier 2 IR11672AS Description IR11672A is a smart secondary-side driver IC designed to drive N-Channel power MOSFETs used as synchronous rectifiers in isolated Flyback and resonant half-bridge converters. The IC can control one or more paralleled N-MOSFETs to emulate the behavior of Schottky diode rectifiers. The drain to source voltage is sensed differentially to determine the polarity of the current and turn the power switch on and off in proximity of the zero current transition. Ruggedness and noise immunity are accomplished using an advanced blanking scheme and double-pulse suppression which allow reliable operation in all operating modes. www.irf.com © 2009 International Rectifier 3 IR11672AS Qualification Information† Qualification Level Moisture Sensitivity Level Machine Model ESD Human Body Model IC Latch-Up Test RoHS Compliant Industrial†† Comments: This family of ICs has passed JEDEC’s Industrial qualification. IR’s Consumer qualification level is granted by extension of the higher Industrial level. MSL2††† 260°C (per IPC/JEDEC J-STD-020) Class B (per JEDEC standard JESD22-A115) Class 2 (per EIA/JEDEC standard EIA/JESD22-A114) Class I, Level A (per JESD78) Yes † †† Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ Higher qualification ratings may be available should the user have such requirements. Please contact your International Rectifier sales representative for further information. ††† Higher MSL ratings may be available for the specific package types listed here. Please contact your International Rectifier sales representative for further information. www.irf.com © 2009 International Rectifier 4 IR11672AS Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM, all currents are defined positive into any lead. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Parameters Supply Voltage Enable Voltage Cont. Drain Sense Voltage Pulse Drain Sense Voltage Source Sense Voltage Gate Voltage Operating Junction Temperature Storage Temperature Thermal Resistance Package Power Dissipation Switching Frequency Symbol VCC VEN VD VD VS VGATE TJ TS RθJA PD fsw Min. -0.3 -0.3 -3 -5 -3 -0.3 -40 -55 Max. 20 20 200 200 20 20 150 150 128 970 500 Units V V V V V V °C °C °C/W mW kHz Remarks VCC=20V, Gate off SOIC-8 SOIC-8, TAMB=25°C Recommended Operating Conditions For proper operation the device should be used within the recommended conditions. Symbol VCC VD TJ Fsw Definition Supply voltage Drain Sense Voltage Junction Temperature Switching Frequency Min. 11.4 -3 -25 --- Max. 18 200 125 500 Units Min. 5 Max. 75 Units kΩ V °C kHz Recommended Component Values Symbol RMOT Component MOT pin resistor value www.irf.com © 2009 International Rectifier 5 IR11672AS Electrical Characteristics VCC=15V and TA = 25°C unless otherwise specified. The output voltage and current (VO and IO) parameters are referenced to GND (pin7). Supply Section Parameters Supply Voltage Operating Range VCC Turn On Threshold VCC Turn Off Threshold (Under Voltage Lock Out) VCC Turn On/Off Hysteresis Operating Current Symbol Min. VCC VCC ON VCC UVLO Max. Units 11.4 9.8 10.55 18 11.3 V V 8.4 9 9.7 V 1.55 8.5 50 1.8 100 150 2.70 1.6 1.5 10 65 2.2 200 200 3.2 2.0 V mA mA mA µA µA V V MΩ VCC HYST ICC Quiescent Current Start-up Current Sleep Current Enable Voltage High Enable Voltage Low Enable Pull-up Resistance IQCC ICC START I SLEEP VENHI VENLO REN Comparator Section Parameters Symbol Turn-off Threshold Typ. VTH1 2.15 1.2 Min. -7 -14 -22 -150 Turn-on Threshold Hysteresis Input Bias Current Input Bias Current Comparator Input Offset VTH2 VHYST IIBIAS1 IIBIAS2 VOFFSET Input CM Voltage Range VCM -0.15 One-Shot Section Parameters Blanking pulse duration Symbol tBLANK Min. 9 Reset Threshold Hysteresis VTH3 VHYST3 Typ. -3.5 -9.5 -18 55 1 30 Typ. 17 2.5 5.4 40 www.irf.com Max. 0 -6 -14 -50 Units mV 7.5 100 2 mV mV µA µA mV 2 V Max. 25 Remarks GBD CLOAD=1nF,fSW=400kHz CLOAD=10nF,fSW=400kHz VCC=VCC ON - 0.1V VEN=0V, VCC =15V GBD Remarks OVT = 0V, VS=0V OVT floating, VS=0V OVT = VCC, VS=0V VD = -50mV VD = 200V GBD Units Remarks µs V VCC=10V – GBD V VCC=20V – GBD mV VCC=10V – GBD © 2009 International Rectifier 6 IR11672AS Electrical Characteristics VCC=15V and TA = 25°C unless otherwise specified. The output voltage and current (VO and IO) parameters are referenced to GND (pin7). Minimum On Time Section Parameters Symbol Minimum on time Gate Driver Section Parameters Gate Low Voltage Gate High Voltage Rise Time Fall Time Min. 190 2.48 Typ. 240 3.1 Max. 290 3.72 Units Remarks ns RMOT =5kΩ, VCC=12V µs RMOT =75kΩ, VCC=12V Symbol VGLO Min. Typ. 0.3 Max. 0.5 VGTH tr1 tr2 tf1 tf2 tDon tDoff rup rdown 9.0 10.7 18 125 10 30 60 50 4 0.7 2 7 12.5 Units Remarks V IGATE = 200mA VCC=12V-18V (internally clamped) V ns CLOAD = 1nF, VCC=12V ns CLOAD = 10nF, VCC=12V ns CLOAD = 1nF, VCC=12V ns CLOAD = 10nF, VCC=12V ns VDS to VGATE -100mV overdrive ns VDS to VGATE -100mV overdrive IGATE = 1A – GBD Ω IGATE = -200mA Ω A CLOAD = 10nF – GBD A CLOAD = 10nF – GBD TONmin Turn on Propagation Delay Turn off Propagation Delay Pull up Resistance Pull down Resistance Output Peak Current(source) IO source Output Peak Current (sink) IO sink www.irf.com 95 75 © 2009 International Rectifier 7 IR11672AS Functional Block Diagram MOT VCC VCC UVLO & REGULATOR EN Cycle by Cycle MOT Check Circuit VCC VD Min ON Time VTH1 RESET VS VGATE DRIVER GND OVT Min OFF Time Vgate RESET VTH3 VTH2 www.irf.com VTH1 VTH3 VDS © 2009 International Rectifier 8 IR11672AS I/O Pin Equivalent Circuit Diagram VD ESD Diode RESD 200V Diode GND www.irf.com © 2009 International Rectifier 9 IR11672AS Lead Definitions PIN# 1 2 3 4 5 6 7 8 Symbol VCC OVT MOT EN VD VS GND VGATE Description Supply Voltage Offset Voltage Trimming Minimum On Time Enable FET Drain Sensing FET Source Sensing Ground Gate Drive Output Lead Assignments www.irf.com © 2009 International Rectifier 10 IR11672AS Detailed Pin Description VCC: Power Supply This is the supply voltage pin of the IC and it is monitored by the under voltage lockout circuit. It is possible to turn off the IC by pulling this pin below the minimum turn off threshold voltage, without damage to the IC. To prevent noise problems, a bypass ceramic capacitor connected to Vcc and COM should be placed as close as possible to the IR11672A. This pin is internally clamped. OVT: Offset Voltage Trimming The OVT pin will program the amount of input offset voltage for the turn-off threshold VTH1. The pin can be optionally tied to ground, to VCC or left floating, to select 3 ranges of input offset trimming. This programming feature allows for accommodating different RDSon MOSFETs. MOT: Minimum On Time The MOT programming pin controls the amount of minimum on time. Once VTH2 is crossed for the first time, the gate signal will become active and turn on the power FET. Spurious ringings and oscillations can trigger the input comparator off. The MOT blanks the input comparator keeping the FET on for a minimum time. The MOT is programmed between 200ns and 3us (typ.) by using a resistor referenced to COM. EN: Enable This pin is used to activate the IC “sleep” mode by pulling the voltage level below 1.6V (typ). In sleep mode the IC will consume a minimum amount of current. All switching functions will be disabled and the gate will be inactive. VD: Drain Voltage Sense VD is the voltage sense pin for the power MOSFET Drain. This is a high voltage pin and particular care must be taken in properly routing the connection to the power MOSFET drain. Additional filtering and or current limiting on this pin are not recommended as it would limit switching performance of the IC. VS: Source Voltage Sense VS is the differential sense pin for the power MOSFET Source. This pin must not be connected directly to the power ground pin (7) but must be used to create a Kelvin contact as close as possible to the power MOSFET source pin. GND: Ground This is ground potential pin of the integrated control circuit. referenced to this point. The internal devices and gate driver are VGATE: Gate Drive Output This is the gate drive output of the IC. Drive voltage is internally limited and provides 2A peak source and 7A peak sink capability. Although this pin can be directly connected to the power MOSFET gate, the use of minimal gate resistor is recommended, especially when putting multiple FETs in parallel. Care must be taken in order to keep the gate loop as short and as small as possible in order to achieve optimal switching performance. www.irf.com © 2009 International Rectifier 11 IR11672AS Application Information and Additional Details State Diagram UVLO/Sleep Mode The IC remains in the UVLO condition until the voltage on the VCC pin exceeds the VCC turn on threshold voltage, VCC ON. During the time the IC remains in the UVLO state, the gate drive circuit is inactive and the IC draws a quiescent current of ICC START. The UVLO mode is accessible from any other state of operation whenever the IC supply voltage condition of VCC < VCC UVLO occurs. The sleep mode is initiated by pulling the EN pin below 1.6V (typ). In this mode the IC is essentially shut down and draws a very low quiescent supply current. Normal Mode and Synchronized Enable Function The IC enters in normal operating mode once the UVLO voltage has been exceeded and the EN voltage is above VENHI threshold. When the IC enters the Normal Mode from the UVLO Mode, the GATE output is disabled (stays low) until VDS exceeds VTH3 to activate the gate. This ensures that the GATE output is not enabled in the middle of a switching cycle. This logic prevents any reverse currents across the device due to the minimum on time function in the IC. The gate will continuously drive the SR MOSFET after this one-time activation. The Cycle by Cycle MOT protection circuit is enabled in Normal Mode. MOT Protection Mode If the secondary current conduction time is shorter than the MOT (Minimum On Time) setting, the next driver output is disabled. This function can avoid reverse current that occurs when the system works at very low duty-cycles or at very light/no load conditions and reduce system standby power consumption by disabling GATE outputs. The Cycle by Cycle MOT Check circuit is always activated under Normal Mode and MOT Protection Mode, so that the IC can automatically resume normal operation once the load increases to a level and the secondary current conduction time is longer than MOT. www.irf.com © 2009 International Rectifier 12 IR11672AS General Description The IR11672A Smart Rectifier IC can emulate the operation of diode rectifier by properly driving a Synchronous Rectifier (SR) MOSFET. The direction of the rectified current is sensed by the input comparator using the power MOSFET RDSon as a shunt resistance and the GATE pin of the MOSFET is driven accordingly. Internal blanking logic is used to prevent spurious transitions and guarantee operation in continuous (CCM), discontinuous (DCM) and critical (CrCM) conduction mode. IR11672A is suitable for Flyback and Resonant Half-Bridge topologies. VGate VDS VTH2 VTH1 VTH3 Figure 1: Input comparator thresholds Flyback Application The modes of operation for a Flyback circuit differ mainly for the turn-off phase of the SR switch, while the turn-on phase of the secondary switch (which corresponds to the turn off of the primary side switch) is identical. Turn-on phase When the conduction phase of the SR FET is initiated, current will start flowing through its body diode, generating a negative VDS voltage across it. The body diode has generally a much higher voltage drop than the one caused by the MOSFET on resistance and therefore will trigger the turn-on threshold VTH2. At that point the IR11672A will drive the gate of MOSFET on which will in turn cause the conduction voltage VDS to drop down. This drop is usually accompanied by some amount of ringing, that can trigger the input comparator to turn off; hence, a Minimum On Time (MOT) blanking period is used that will maintain the power MOSFET on for a minimum amount of time. The programmed MOT will limit also the minimum duty cycle of the SR MOSFET and, as a consequence, the max duty cycle of the primary side switch. DCM/CrCM Turn-off phase Once the SR MOSFET has been turned on, it will remain on until the rectified current will decay to the level where VDS will cross the turn-off threshold VTH1. This will happen differently depending on the mode of operation. In DCM the current will cross the threshold with a relatively low dI/dt. Once the threshold is crossed, the current will start flowing again thru the body diode, causing the VDS voltage to jump negative. Depending on the amount of residual current, VDS may trigger once again the turn on threshold: for this reason VTH2 is blanked for a certain amount of time (TBLANK) after VTH1 has been triggered. The blanking time is internally set. As soon as VDS crosses the positive threshold VTH3 also the blanking time is terminated and the IC is ready for next conduction cycle. www.irf.com © 2009 International Rectifier 13 IR11672AS IPRIM VPRIM T1 time T3 T2 ISEC VSEC time Figure 2: Primary and secondary currents and voltages for DCM mode IPRIM VPRIM T1 time T2 ISEC VSEC time Figure 3: Primary and secondary currents and voltages for CrCM mode CCM Turn-off phase In CCM mode the turn off transition is much steeper and dI/dt involved is much higher. The turn on phase is identical to DCM or CrCM and therefore won’t be repeated here. During the SR FET conduction phase the current will decay linearly, and so will VDS on the SR FET. Once the primary switch will start to turn back on, the SR FET current will rapidly decrease crossing VTH1 and turning the gate off. The turn off speed is critical to avoid cross conduction on the primary side and reduce switching losses. Also in this case a blanking period will be applied, but given the very fast nature of this transition, it will be reset as soon as VDS crosses VTH3. www.irf.com © 2009 International Rectifier 14 IR11672AS IPRIM VPRIM T1 time T2 ISEC VSEC time Figure 4: Primary and secondary currents and voltages for CCM mode The operation waveforms of IR11672A in a flyback converter under CCM mode and DCM/CrCM were shown in Figure 5 and Figure 6 respectively. VTH3 ISEC VDS T1 T2 time VTH1 VTH2 Gate Drive time Blanking time MOT Figure 5: Secondary side CCM operation www.irf.com © 2009 International Rectifier 15 IR11672AS VTH3 ISEC VDS T1 T2 time VTH1 VTH2 Gate Drive time Blanking MOT 10us blanking Figure 6: Secondary side DCM/CrCM operation Resonant Half-Bridge Application The typical application circuit of IR11672A in LLC half-bridge is shown in Figure 7. M3 Rcc1 CVCC1 Rg1 Vin 1 2 3 4 M1 Lr VCC OVT MOT EN Rmot1 T1 M2 GATE GND VS VD 8 7 6 5 IR11672A Lm Cr VOUT Rcc2 CVCC2 Rtn 1 2 3 4 Rmot2 VCC OVT MOT EN GATE GND VS VD 8 7 6 5 Cout Rg2 IR11672A M4 Figure 7: Resonant half-bridge application circuit In resonant half-bridge converter, the turn-on phase and turn-off phase is similar to flyback except the current shape is sinusoid. The typical operation waveform can be found below. www.irf.com © 2009 International Rectifier 16 IR11672AS Figure 8: Resonant half-bridge operation waveform MOT Protection Mode The MOT protection prevents reverse current in SR MOSFET which could happen at light load if the MOT time is set very long. The IC disables the gate output in the protection mode and automatically resume to normal operation as the load increasing to a level where the SR current conduction time is longer than MOT. This function works in both flyback and resonant half-bridge topologies. Figure 9 is an example in Flyback converter. Figure 9: MOT Protection Mode www.irf.com © 2009 International Rectifier 17 IR11672AS Synchronized Enable Function This function works in both flyback and resonant half-bridge topologies. Figure 10 is an example in resonant half-bridge converter. Figure 10: Synchronized Enable Function (resonant half-bridge) General Timing Waveform VCC VCC ON VCC UVLO t UVLO NORMAL UVLO Figure 11: Vcc UVLO VTH1 VDS VTH2 t Don t Doff VGate 90% 50% 10% t rise tfall Figure 12: Timing waveform www.irf.com © 2009 International Rectifier 18 IR11672AS Figure 14: Undervoltage Lockout vs. Temperature Figure 13: Supply Current vs. Supply Voltage Figure 16: Icc Supply Currrent @1nF Load vs. Temperature Figure 15: Icc Quiescent Currrent vs. Temperature www.irf.com © 2009 International Rectifier 19 IR11672AS Figure 17: VTH1 vs. Temperature Figure 18: VTH2 vs. Temperature Figure 19: Comparator Hysteresis vs. Temperature Figure 20: VTH1 vs. Temperature and Common Mode (OVT=Floating) www.irf.com © 2009 International Rectifier 20 IR11672AS Figure 22: MOT vs Temperature Figure 21: VTH2 vs. Temperature and Common Mode Figure 23: Enable Threshold vs. Temperature Figure 24: Turn-on and Turn-off Propagation Delay vs. Temperature www.irf.com © 2009 International Rectifier 21 IR11672AS Package Details: SOIC8N www.irf.com © 2009 International Rectifier 22 IR11672AS Tape and Reel Details: SOIC8N LOADED TAPE FEED DIRECTION A B H D F C NOTE : CONTROLLING DIM ENSION IN M M E G CARRIER TAPE DIMENSION FOR Metric Code Min Max A 7.90 8.10 B 3.90 4.10 C 11.70 12.30 D 5.45 5.55 E 6.30 6.50 F 5.10 5.30 G 1.50 n/a H 1.50 1.60 8SOICN Imperial Min Max 0.311 0.318 0.153 0.161 0.46 0.484 0.214 0.218 0.248 0.255 0.200 0.208 0.059 n/a 0.059 0.062 F D C B A E G H REEL DIMENSIONS FOR 8SOICN Metric Code Min Max A 329.60 330.25 B 20.95 21.45 C 12.80 13.20 D 1.95 2.45 E 98.00 102.00 F n/a 18.40 G 14.50 17.10 H 12.40 14.40 Imperial Min Max 12.976 13.001 0.824 0.844 0.503 0.519 0.767 0.096 3.858 4.015 n/a 0.724 0.570 0.673 0.488 0.566 www.irf.com © 2009 International Rectifier 23 IR11672AS Part Marking Information www.irf.com © 2009 International Rectifier 24 IR11672AS Ordering Information Standard Pack Base Part Number IR11672AS Package Type SOIC8N Complete Part Number Form Quantity Tube/Bulk 95 IR11672ASPBF Tape and Reel 2500 IR11672ASTRPBF The information provided in this document is believed to be accurate and reliable. However, International Rectifier assumes no responsibility for the consequences of the use of this information. International Rectifier assumes no responsibility for any infringement of patents or of other rights of third parties which may result from the use of this information. No license is granted by implication or otherwise under any patent or patent rights of International Rectifier. The specifications mentioned in this document are subject to change without notice. This document supersedes and replaces all information previously supplied. For technical support, please contact IR’s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 www.irf.com © 2009 International Rectifier 25