PHILIPS PCF8574P

INTEGRATED CIRCUITS
DATA SHEET
PCF8574
Remote 8-bit I/O expander for
I2C-bus
Product specification
Supersedes data of September 1994
File under Integrated Circuits, IC12
1997 Apr 02
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
CONTENTS
1
FEATURES
2
GENERAL DESCRIPTION
3
ORDERING INFORMATION
4
BLOCK DIAGRAM
5
PINNING
6
CHARACTERISTICS OF THE I2C-BUS
6.1
6.2
6.3
6.4
Bit transfer
Start and stop conditions
System configuration
Acknowledge
7
FUNCTIONAL DESCRIPTION
7.1
7.2
7.3
Addressing
Interrupt
Quasi-bidirectional I/Os
8
LIMITING VALUES
9
HANDLING
10
DC CHARACTERISTICS
11
I2C-BUS TIMING CHARACTERISTICS
12
PACKAGE OUTLINES
13
SOLDERING
13.1
13.2
13.2.1
13.2.2
13.3
13.3.1
13.3.2
13.3.3
Introduction
DIP
Soldering by dipping or by wave
Repairing soldered joints
SO and SSOP
Reflow soldering
Wave soldering
Repairing soldered joints
14
DEFINITIONS
15
LIFE SUPPORT APPLICATIONS
16
PURCHASE OF PHILIPS I2C COMPONENTS
1997 Apr 02
2
PCF8574
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
1
FEATURES
PCF8574
2
• Operating supply voltage 2.5 to 6 V
GENERAL DESCRIPTION
The PCF8574 is a silicon CMOS circuit. It provides general
purpose remote I/O expansion for most microcontroller
families via the two-line bidirectional bus (I2C).
• Low standby current consumption of 10 µA maximum
• I2C to parallel port expander
The device consists of an 8-bit quasi-bidirectional port and
an I2C-bus interface. The PCF8574 has a low current
consumption and includes latched outputs with high
current drive capability for directly driving LEDs. It also
possesses an interrupt line (INT) which can be connected
to the interrupt logic of the microcontroller. By sending an
interrupt signal on this line, the remote I/O can inform the
microcontroller if there is incoming data on its ports without
having to communicate via the I2C-bus. This means that
the PCF8574 can remain a simple slave device.
• Open-drain interrupt output
• 8-bit remote I/O port for the I2C-bus
• Compatible with most microcontrollers
• Latched outputs with high current drive capability for
directly driving LEDs
• Address by 3 hardware address pins for use of up to
8 devices (up to 16 with PCF8574A)
• DIP16, or space-saving SO16 or SSOP20 packages.
The PCF8574 and PCF8574A versions differ only in their
slave address as shown in Fig.9.
3
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
PCF8574P;
PCF8574AP
DIP16
plastic dual in-line package; 16 leads (300 mil)
SOT38-1
PCF8574T;
PCF8574AT
SO16
plastic small outline package; 16 leads; body width 7.5 mm
SOT162-1
PCF8574TS
SSOP20
plastic shrink small outline package; 20 leads; body width 4.4 mm
SOT266-1
1997 Apr 02
3
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
4
PCF8574
BLOCK DIAGRAM
handbook, full pagewidth
INT
13
INTERRUPT
LOGIC
A0
A1
A2
SCL
SDA
LP FILTER
PCF8574
1
2
4
3
5
6
14
15
INPUT
FILTER
I 2 C BUS
CONTROL
7
SHIFT
REGISTER
8 BIT
I/O
PORT
9
10
11
12
WRITE pulse
VDD
V SS
16
8
READ pulse
POWER-ON
RESET
MBD980
Fig.1 Block diagram (SOT38-1 and SOT162-1).
1997 Apr 02
4
P0
P1
P2
P3
P4
P5
P6
P7
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
5
PCF8574
PINNING
PIN
SYMBOL
DESCRIPTION
DIP16; SO16
SSOP20
A0
1
6
address input 0
A1
2
7
address input 1
A2
3
9
address input 2
P0
4
10
quasi-bidirectional I/O 0
P1
5
11
quasi-bidirectional I/O 1
P2
6
12
quasi-bidirectional I/O 2
P3
7
14
quasi-bidirectional I/O 3
VSS
8
15
supply ground
P4
9
16
quasi-bidirectional I/O 4
P5
10
17
quasi-bidirectional I/O 5
P6
11
19
quasi-bidirectional I/O 6
P7
12
20
quasi-bidirectional I/O 7
INT
13
1
interrupt output (active LOW)
SCL
14
2
serial clock line
SDA
15
4
serial data line
VDD
16
5
supply voltage
n.c.
−
3
not connected
n.c.
−
8
not connected
n.c.
−
13
not connected
n.c.
−
18
not connected
handbook, halfpage
handbook, halfpage
INT
1
20
P7
SCL
2
19
P6
A0
1
16 VDD
A1
2
15
SDA
n.c.
3
18
n.c.
A2
3
14
SCL
SDA
4
17
P5
P0
4
13
INT
VDD
5
16
P4
P7
A0
6
15
VSS
PCF8574
PCF8574A
PCF8574TS
P1
5
P2
6
11 P6
A1
7
14
P3
P3
7
10
P5
n.c.
8
13
n.c.
VSS
8
9
P4
A2
9
12
P2
P0 10
11
P1
12
MBD979
MBD978
Fig.2 Pin configuration (DIP16; SO16).
1997 Apr 02
Fig.3 Pin configuration (SSOP20).
5
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
6
CHARACTERISTICS OF THE I2C-BUS
PCF8574
6.2
The I2C-bus is for 2-way, 2-line communication between
different ICs or modules. The two lines are a serial data
line (SDA) and a serial clock line (SCL). Both lines must be
connected to a positive supply via a pull-up resistor when
connected to the output stages of a device. Data transfer
may be initiated only when the bus is not busy.
Both data and clock lines remain HIGH when the bus is not
busy. A HIGH-to-LOW transition of the data line, while the
clock is HIGH is defined as the start condition (S).
A LOW-to-HIGH transition of the data line while the clock
is HIGH is defined as the stop condition (P) (see Fig.5).
6.3
6.1
Start and stop conditions
Bit transfer
System configuration
A device generating a message is a ‘transmitter’, a device
receiving is the ‘receiver’. The device that controls the
message is the ‘master’ and the devices which are
controlled by the master are the ‘slaves’ (see Fig.6).
One data bit is transferred during each clock pulse. The
data on the SDA line must remain stable during the HIGH
period of the clock pulse as changes in the data line at this
time will be interpreted as control signals (see Fig.4).
SDA
SCL
change
of data
allowed
data line
stable;
data valid
MBC621
Fig.4 Bit transfer.
SDA
SDA
SCL
SCL
S
P
START condition
STOP condition
MBC622
Fig.5 Definition of start and stop conditions.
SDA
SCL
MASTER
TRANSMITTER /
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER /
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER /
RECEIVER
MBA605
Fig.6 System configuration.
1997 Apr 02
6
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
6.4
PCF8574
transmitter. The device that acknowledges has to pull
down the SDA line during the acknowledge clock pulse, so
that the SDA line is stable LOW during the HIGH period of
the acknowledge related clock pulse, set-up and hold
times must be taken into account.
Acknowledge
The number of data bytes transferred between the start
and the stop conditions from transmitter to receiver is not
limited. Each byte of eight bits is followed by one
acknowledge bit. The acknowledge bit is a HIGH level put
on the bus by the transmitter whereas the master
generates an extra acknowledge related clock pulse.
A master receiver must signal an end of data to the
transmitter by not generating an acknowledge on the last
byte that has been clocked out of the slave. In this event
the transmitter must leave the data line HIGH to enable the
master to generate a stop condition.
A slave receiver which is addressed must generate an
acknowledge after the reception of each byte. Also a
master must generate an acknowledge after the reception
of each byte that has been clocked out of the slave
DATA OUTPUT
BY TRANSMITTER
not acknowledge
DATA OUTPUT
BY RECEIVER
acknowledge
SCL FROM
MASTER
1
2
8
9
S
START
CONDITION
MBC602
Fig.7 Acknowledgment on the I2C-bus.
1997 Apr 02
7
clock pulse for
acknowledgement
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
7
PCF8574
FUNCTIONAL DESCRIPTION
VDD
handbook, full pagewidth
write pulse
100
µA
data from
shift register
D
Q
FF
P0 to P7
CI
S
power-on
reset
V SS
D
Q
FF
CI
read pulse
S
to interrupt
logic
data to
shift register
MBD977
Fig.8 Simplified schematic diagram of each I/O.
7.1
Addressing
For addressing see Figs 9, 10 and 11.
slave address
handbook, full pagewidth
S
0
1
0
0
A2
slave address
A1
A0
0
A
S
0
1
1
1
A2
A1
A0
0
A
MBD973
a.
b.
(a) PCF8574.
(b) PCF8574A.
Fig.9 PCF8574 and PCF8574A slave addresses.
Each of the PCF8574’s eight I/Os can be independently
used as an input or output. Input data is transferred from
the port to the microcontroller by the READ mode
(see Fig.11). Output data is transmitted to the port by the
WRITE mode (see Fig.10).
1997 Apr 02
8
1997 Apr 02
9
DATA OUT
FROM PORT
WRITE TO
PORT
3
4
5
6
1
0
0
A2
A1
slave address (PCF8574)
2
A0
7
R/W
0
8
DATA 1
t pv
acknowledge
from slave
A
DATA 1 VALID
DATA 2
data to port
t pv
MBD974
DATA 2 VALID
acknowledge
from slave
A
Remote 8-bit I/O expander for I2C-bus
Fig.10 WRITE mode (output).
acknowledge
from slave
A
data to port
ndbook, full pagewidth
start condition
0
SDA
S
1
SCL
Philips Semiconductors
Product specification
PCF8574
1997 Apr 02
10
0
1
t iv
start condition
S
0
0
A2
A1
A0
t ph
R/W
1
t ir
DATA 2
acknowledge
from slave
A
DATA 3
t ps
t ir
acknowledge
from slave
DATA 4
DATA 4
DATA 1
A
data from port
data from port
P
MBD975
stop
condition
1
htdiwegap lluf ,koobdnah
Fig.11 READ mode (input).
Remote 8-bit I/O expander for I2C-bus
A LOW-to-HIGH transition of SDA, while SCL is HIGH is defined as the stop condition (P). Transfer of data can be stopped at any moment by a stop condition. When this occurs, data present
at the last acknowledge phase is valid (output mode). Input data is lost.
INT
DATA INTO
PORT
READ FROM
PORT
SDA
slave address (PCF8574)
Philips Semiconductors
Product specification
PCF8574
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
7.2
• Interrupts which occur during the acknowledge clock
pulse may be lost (or very short) due to the resetting of
the interrupt during this pulse.
Interrupt (see Figs 12 and 13)
The PCF8574 provides an open drain output (INT) which
can be fed to a corresponding input of the microcontroller.
This gives these chips a type of master function which can
initiate an action elsewhere in the system.
Each change of the I/Os after resetting will be detected
and, after the next rising clock edge, will be transmitted as
INT. Reading from or writing to another device does not
affect the interrupt circuit.
An interrupt is generated by any rising or falling edge of the
port inputs in the input mode. After time tiv the signal INT is
valid.
7.3
Resetting and reactivating the interrupt circuit is achieved
when data on the port is changed to the original setting or
data is read from or written to the port which has generated
the interrupt.
• In the READ mode at the acknowledge bit after the rising
edge of the SCL signal
• In the WRITE mode at the acknowledge bit after the
HIGH-to-LOW transition of the SCL signal
V DD
MICROCOMPUTER
Quasi-bidirectional I/Os (see Fig.14)
A quasi-bidirectional I/O can be used as an input or output
without the use of a control signal for data direction.
At power-on the I/Os are HIGH. In this mode only a current
source to VDD is active. An additional strong pull-up to VDD
allows fast rising edges into heavily loaded outputs. These
devices turn on when an output is written HIGH, and are
switched off by the negative edge of SCL. The I/Os should
be HIGH before being used as inputs.
Resetting occurs as follows:
handbook, full pagewidth
PCF8574
PCF8574
(1)
PCF8574
(2)
PCF8574
(16)
INT
INT
INT
INT
MBD976
Fig.12 Application of multiple PCF8574s with interrupt.
slave address (PCF8574)
handbook, full pagewidth
SDA
S
0
1
0
0
A2
A1
data from port
A0
start condition
SCL
1
2
1
R/W
3
4
5
6
7
A
1
acknowledge P5
from slave
1
P
stop
condition
8
DATA INTO
P5
INT
t iv
t ir
Fig.13 Interrupt generated by a change of input to I/O P5.
1997 Apr 02
11
MBD972
1997 Apr 02
12
P3
PULL-UP
OUTPUT
CURRENT
P3
OUTPUT
VOLTAGE
SCL
SDA
0
1
2
3
1
4
1
5
A2
6
A1
7
A0
8
R/W
0
acknowledge
from slave
A
P3
1
I OHt
A
P3
0
data to port
MBD971
I OH
A
P
Remote 8-bit I/O expander for I2C-bus
Fig.14 Transient pull-up current IOHt while P3 changes from LOW-to-HIGH and back to LOW.
1
start condition
S
data to port
handbook, full pagewidth
slave address (PCF8574A)
Philips Semiconductors
Product specification
PCF8574
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
8 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VDD
supply voltage
−0.5
+7.0
V
VI
input voltage
VSS − 0.5
VDD + 0.5
V
II
DC input current
−
±20
mA
IO
DC output current
−
±25
mA
IDD
supply current
−
±100
mA
ISS
supply current
−
±100
mA
Ptot
total power dissipation
−
400
mW
PO
power dissipation per output
−
100
mW
Tstg
storage temperature
−65
+150
°C
Tamb
operating ambient temperature
−40
+85
°C
9
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take precautions appropriate to handling MOS devices. Advice can be found in Data Handbook IC12 under
“Handling MOS Devices”.
10 DC CHARACTERISTICS
VDD = 2.5 to 6 V; VSS = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
VDD
supply voltage
IDD
supply current
Istb
standby current
VPOR
Power-on reset voltage
−
6.0
V
operating mode; VDD = 6 V; −
no load; VI = VDD or VSS;
fSCL = 100 kHz
40
100
µA
standby mode; VDD = 6 V;
no load; VI = VDD or VSS
−
2.5
10
µA
VDD = 6 V; no load;
VI = VDD or VSS; note 1
−
1.3
2.4
V
2.5
Input SCL; input/output SDA
VIL
LOW level input voltage
−0.5
−
+0.3VDD
V
VIH
HIGH level input voltage
0.7VDD
−
VDD + 0.5
V
IOL
LOW level output current
VOL = 0.4 V
3
−
−
mA
IL
leakage current
VI = VDD or VSS
−1
−
+1
µA
Ci
input capacitance
VI = VSS
−
−
7
pF
1997 Apr 02
13
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
SYMBOL
PARAMETER
PCF8574
CONDITIONS
MIN.
TYP.
MAX.
UNIT
I/Os
VIL
LOW level input voltage
−0.5
−
+0.3VDD
V
VIH
HIGH level input voltage
0.7VDD
−
VDD + 0.5
V
IIHL(max)
maximum allowed input
current through protection
diode
VI ≥ VDD or VI ≤ VSS
−
−
±400
µA
IOL
LOW level output current
VOL = 1 V; VDD = 5 V
10
25
−
mA
IOH
HIGH level output current
VOH = VSS
30
−
300
µA
IOHt
transient pull-up current
HIGH during acknowledge
(see Fig.14); VOH = VSS;
VDD = 2.5 V
−
−1
−
mA
Ci
input capacitance
−
−
10
pF
Co
output capacitance
−
−
10
pF
−
−
4
µs
Port timing; CL ≤ 100 pF (see Figs 10 and 11)
tpv
output data valid
tsu
input data set-up time
0
−
−
µs
th
input data hold time
4
−
−
µs
Interrupt INT (see Fig.13)
IOL
LOW level output current
VOL = 0.4 V
1.6
−
−
mA
IL
leakage current
VI = VDD or VSS
−1
−
+1
µA
TIMING; CL ≤ 100 PF
tiv
input data valid time
−
−
4
µs
tir
reset delay time
−
−
4
µs
Select inputs A0 to A2
VIL
LOW level input voltage
−0.5
−
+0.3VDD
V
VIH
HIGH level input voltage
0.7VDD
−
VDD + 0.5
V
ILI
input leakage current
−250
−
+250
nA
pin at VDD or VSS
Note
1. The Power-on reset circuit resets the I2C-bus logic with VDD < VPOR and sets all I/Os to logic 1 (with current source
to VDD).
1997 Apr 02
14
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
11 I2C-BUS TIMING CHARACTERISTICS
SYMBOL
PARAMETER
MIN.
TYP.
MAX.
UNIT
I2C-BUS TIMING (see Fig.15; note 1)
fSCL
SCL clock frequency
−
−
100
kHz
tSW
tolerable spike width on bus
−
−
100
ns
tBUF
bus free time
4.7
−
−
µs
tSU;STA
START condition set-up time
4.7
−
−
µs
tHD;STA
START condition hold time
4.0
−
−
µs
tLOW
SCL LOW time
4.7
−
−
µs
tHIGH
SCL HIGH time
4.0
−
−
µs
tr
SCL and SDA rise time
−
−
1.0
µs
tf
SCL and SDA fall time
−
−
0.3
µs
tSU;DAT
data set-up time
250
−
−
ns
tHD;DAT
data hold time
0
−
−
ns
tVD;DAT
SCL LOW to data out valid
−
−
3.4
µs
tSU;STO
STOP condition set-up time
4.0
−
−
µs
Note
1. All the timing values are valid within the operating supply voltage and ambient temperature range and refer to VIL
and VIH with an input voltage swing of VSS to VDD.
handbook, full pagewidth
t SU;STA
BIT 6
(A6)
BIT 7
MSB
(A7)
START
CONDITION
(S)
PROTOCOL
t LOW
t HIGH
BIT 0
LSB
(R/W)
ACKNOWLEDGE
(A)
STOP
CONDITION
(P)
1 / f SCL
SCL
t
tr
BUF
tf
SDA
t HD;STA
t SU;DAT
t
HD;DAT
Fig.15 I2C-bus timing diagram.
1997 Apr 02
15
t VD;DAT
MBD820
t SU;STO
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
12 PACKAGE OUTLINES
DIP16: plastic dual in-line package; 16 leads (300 mil); long body
SOT38-1
ME
seating plane
D
A2
A
A1
L
c
e
Z
b1
w M
(e 1)
b
MH
9
16
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.7
0.51
3.7
1.40
1.14
0.53
0.38
0.32
0.23
21.8
21.4
6.48
6.20
2.54
7.62
3.9
3.4
8.25
7.80
9.5
8.3
0.254
2.2
inches
0.19
0.020
0.15
0.055
0.045
0.021
0.015
0.013
0.009
0.86
0.84
0.26
0.24
0.10
0.30
0.15
0.13
0.32
0.31
0.37
0.33
0.01
0.087
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT38-1
050G09
MO-001AE
1997 Apr 02
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-10-02
95-01-19
16
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
SO16: plastic small outline package; 16 leads; body width 7.5 mm
SOT162-1
D
E
A
X
c
HE
y
v M A
Z
9
16
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
8
e
detail X
w M
bp
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
mm
2.65
0.30
0.10
2.45
2.25
0.25
0.49
0.36
0.32
0.23
10.5
10.1
7.6
7.4
1.27
10.65
10.00
1.4
1.1
0.4
1.1
1.0
0.25
0.25
0.1
0.9
0.4
inches
0.10
0.012 0.096
0.004 0.089
0.01
0.019 0.013
0.014 0.009
0.41
0.40
0.30
0.29
0.050
0.419
0.043
0.055
0.394
0.016
0.043
0.039
0.01
0.01
0.004
0.035
0.016
Z
(1)
θ
8o
0o
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT162-1
075E03
MS-013AA
1997 Apr 02
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
95-01-24
97-05-22
17
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
SSOP20: plastic shrink small outline package; 20 leads; body width 4.4 mm
D
SOT266-1
E
A
X
c
y
HE
v M A
Z
11
20
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
10
detail X
w M
bp
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.5
0.15
0
1.4
1.2
0.25
0.32
0.20
0.20
0.13
6.6
6.4
4.5
4.3
0.65
6.6
6.2
1.0
0.75
0.45
0.65
0.45
0.2
0.13
0.1
0.48
0.18
10
0o
Note
1. Plastic or metal protrusions of 0.20 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
90-04-05
95-02-25
SOT266-1
1997 Apr 02
EUROPEAN
PROJECTION
18
o
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
13 SOLDERING
13.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
13.3.2
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
13.2
13.2.1
DIP
If wave soldering cannot be avoided, the following
conditions must be observed:
SOLDERING BY DIPPING OR BY WAVE
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
• The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
13.3
13.3.1
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
SO and SSOP
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO and
SSOP packages.
13.3.3
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
1997 Apr 02
WAVE SOLDERING
Wave soldering is not recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
13.2.2
PCF8574
19
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
PCF8574
14 DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
15 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
16 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1997 Apr 02
20
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
NOTES
1997 Apr 02
21
PCF8574
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
NOTES
1997 Apr 02
22
PCF8574
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I2C-bus
NOTES
1997 Apr 02
23
PCF8574
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580/xxx
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2870, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA53
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
417067/1200/02/pp24
Date of release: 1997 Apr 02
Document order number:
9397 750 01758