PDF 用户手册

EVAL-ADM1087EBZ User Guide
UG-617
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Kit for ADM1087 Sequencer
FEATURES
GENERAL DESCRIPTION
Full featured evaluation board for the ADM1087 sequencer
3 LEDs indicate output sequence
Dedicated ENABLE/DISABLE switch
On-board test points to examine ADM1087 operation
On-board expansion feature to add more ADM1087 devices
The ADM1087 evaluation board (EVAL-ADM1087EBZ) is a
fully featured board for evaluating ADM1087 sequencers.
The board is designed to power up with a 9 V input supply that can
be turned on and off using a dedicated switch (Switch S1, ON/OFF).
The two ADM1087 devices on the board can be enabled and
disabled using another switch (Switch S2, ENABLE/DISABLE).
When enabled, the ADM1087 devices on the board monitor a
voltage rail and turn on the corresponding three ADP3334 LDO
devices in a sequence. LEDs on the board provide a direct visual
indication of the sequencing of three different voltages: 3.3 V,
2.5 V, and 1.8 V.
EVALUATION KIT CONTENTS
ADM1087 evaluation board
Complete specifications for the ADM1087 can be found in the
ADM1087 data sheet, available at www.analog.com, and should
be consulted in conjunction with this user guide when using the
evaluation board.
11837-001
PHOTOGRAPH OF THE EVALUATION BOARD
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 8
UG-617
EVAL-ADM1087EBZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Board Description .........................................................3
Evaluation Kit Contents ................................................................... 1
Evaluation Board Hardware .............................................................4
General Description ......................................................................... 1
Evaluation Board Connector, Switch, LED Functions .............4
Photograph of the Evaluation Board .............................................. 1
Evaluation Board Schematic ............................................................5
Revision History ............................................................................... 2
Bill of Materials ..................................................................................6
REVISION HISTORY
11/13—Revision 0: Initial Version
Rev. 0 | Page 2 of 8
EVAL-ADM1087EBZ User Guide
UG-617
EVALUATION BOARD DESCRIPTION
A 9 V battery supplies power to the board. The board functions
as follows:
The EVAL-ADM1087EBZ is designed to demonstrate the
features of the ADM1087 sequencer. A simplified block
diagram of the evaluation board is shown in Figure 2.
1.
Two ADM1087 devices are used to sequence the outputs of
three ADP3334 LDO regulators. Separate capacitors on the
CEXT pin of each ADM1087 device determine the time delays
between enabling the 3.3 V, 2.5 V, and 1.8 V supplies. The LDO
regulators and ADM1087 devices are connected in a cascade;
therefore, the output of each regulator is dependent on the output
of the previous device.
2.
3.
4.
There are two switches included on the board:
•
The S1 switch (ON/OFF) is used to power up or power
down the board.
The S2 switch (ENABLE/DISABLE) is used to enable or
disable the ADM1087 devices.
S1
SD
IN
ADP3334
D1
OUT
3.3V
SD
Q1
IN
ADP3334
D2
OUT
2.5V
3.3V
D3
OUT
1.8V
Q3
VCC
VIN
ENOUT
ADM1087
ENIN
IN
ADP3334
3.3V
VCC
VIN
SD
Q2
ENOUT
ADM1087
CEXT
ENIN
CEXT
9V
S2
11837-002
•
Place the S1 switch into the ON position to turn on the
first ADP3334 LDO regulator.
The ADM1087 devices monitor the output of this
regulator. When the output reaches 3.3 V, the red LED (D1)
illuminates and the second ADP3334 LDO regulator turns on.
The ADM1087 devices monitor the output of this
regulator. When the output reaches 2.5 V, the yellow LED (D2)
illuminates and the third ADP3334 LDO regulator turns on.
The ADM1087 devices monitor the output of this
regulator. When the output reaches 1.8 V, the green LED (D3)
illuminates.
Figure 2. Simplified Block Diagram of EVAL-ADM1087EBZ
Rev. 0 | Page 3 of 8
UG-617
EVAL-ADM1087EBZ User Guide
EVALUATION BOARD HARDWARE
EVALUATION BOARD CONNECTOR, SWITCH, LED FUNCTIONS
Table 1. Connector Functions
Reference
P1
Function
Connects the positive and negative terminal of a 9 V battery.
Table 2. Switch Functions
Reference
S1
S2
Position
ON
OFF
ENABLE
DISABLE
Function
Powers up the board.
Powers down the board.
Enables the ADM1087 devices.
Disables the ADM1087 devices.
Table 3. LED Functions
Reference
D1
D2
D3
LED Color
Red
Yellow
Green
Function
Illuminates when the first ADP3334 LDO regulator output is 3.3 V.
Illuminates when the second ADP3334 LDO regulator output is 2.5 V.
Illuminates when the third ADP3334 LDO regulator output is 1.8 V.
Rev. 0 | Page 4 of 8
EVAL-ADM1087EBZ User Guide
UG-617
11837-003
EVALUATION BOARD SCHEMATIC
Figure 3. EVAL-ADM1087EBZ Schematic, Page 1
Rev. 0 | Page 5 of 8
UG-617
EVAL-ADM1087EBZ User Guide
BILL OF MATERIALS
Table 4. Bill of Materials for the EVAL-ADM1087EBZ
Name
C1
C2
C3
C4
C5
C6
C7
C8
C9
D1
D2
D3
P1
Q1
Q2
Q3
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
S1
S2
T1
T2
T3
T4
T5
T6
T7
U1
U2
U3
U4
U5
Part Type
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
LED
LED
LED
BATT_PP3
BC850B
BC850B
BC850B
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
SW-SPDT-SLIDE
SW-SPDT-SLIDE
Test point
Test point
Test point
Test point
Test point
Test point
Test point
LDO regulator
LDO regulator
LDO regulator
Sequencer
Sequencer
Value
1 µF
1 µF
1 µF
1 µF
1 µF
1 µF
100 nF
100 nF
1 µF
75 kΩ
150 kΩ
3.9 kΩ
10 kΩ
91 kΩ
110 kΩ
3.9 kΩ
10 kΩ
150 kΩ
75 kΩ
3.9 kΩ
160 kΩ
51 kΩ
110 kΩ
51 kΩ
10 kΩ
10 kΩ
10 kΩ
Description
16 V, Y5V, ceramic capacitor
16 V, Y5V, ceramic capacitor
16 V, Y5V, ceramic capacitor
16 V, Y5V, ceramic capacitor
16 V, Y5V, ceramic capacitor
16 V, Y5V, ceramic capacitor
35 V through-hole tantalum capacitor
35 V through-hole tantalum capacitor
16 V, Y5V, ceramic capacitor
Red LED
Yellow LED
Green LED
Pair battery connectors
General-purpose transistor
General-purpose transistor
General-purpose transistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
0.1 W resistor
SPDT slide switch
SPDT slide switch
Test point
Test point
Test point
Test point
Test point
Test point
Test point
High accuracy, low IQ, anyCAP® adjustable low dropout regulator in 8-lead MSOP
High accuracy, low IQ, anyCAP adjustable low dropout regulator in 8-lead MSOP
High accuracy, low IQ, anyCAP adjustable low dropout regulator in 8-lead MSOP
Voltage Sequencer with Active Low, Open-Drain Enable Output in 6-lead SC70
Voltage Sequencer with Active Low, Open-Drain Enable Output in 6-lead SC70
Rev. 0 | Page 6 of 8
Stock Code
FEC 318-8899
FEC 318-8899
FEC 318-8899
FEC 318-8899
FEC 318-8899
FEC 318-8899
FEC 1100483
FEC 1100483
FEC 318-8899
FEC 114-2512
FEC 114-2515
FEC 114-2509
FEC 723-988
FEC 108-1239
FEC 108-1239
FEC 108-1239
FEC 933-3541
FEC 933-2626
FEC 933-3169
FEC 933-2391
FEC 933-3649
FEC 933-2464
FEC 933-3169
FEC 933-2391
FEC 933-2626
FEC 933-3541
FEC 933-3169
FEC 933-2685
FEC 933-3339
FEC 933-2464
FEC 933-3339
FEC 933-2391
FEC 933-2391
FEC 933-2391
FEC 112-3875
FEC 112-3875
FEC 873-1144
FEC 873-1144
FEC 873-1144
FEC 873-1144
FEC 873-1144
FEC 873-1144
FEC 873-1144
ADP3334ARMZ-REEL7
ADP3334ARMZ-REEL7
ADP3334ARMZ-REEL7
ADM1087AKSZ-REEL7
ADM1087AKSZ-REEL7
EVAL-ADM1087EBZ User Guide
UG-617
NOTES
Rev. 0 | Page 7 of 8
UG-617
EVAL-ADM1087EBZ User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG11837-0-11/13(0)
Rev. 0 | Page 8 of 8