RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E REVISION RECORD DESCRIPTION REV DATE 0 INITIAL RELEASE 06/24/03 A • PAGE 3, CHANGED INITIAL RATE OF RADS TO 240 RADS/SEC. 03/15/05 B • PAGE 4, CHANGED IN BOTH PARAGRAPHS 4.2, 4.3 IN CONJUNCTION TO 3.3 CHANGED TO 3.4 AND PARAGRAPH 4.3 CHANGED 3.1.1 TO 3.1 AND 3.2.1 TO 3.1.1. CHANGED POSTIRRADIATION, VS=5V, 3V, 50Krad, IB FROM 809 TO 800 nA, PAGE 14. 01/09/08 C • PAGE 3, PARAGRAPH 3.11.1 CHANGED VERBIAGE. 05/05/08 D • PAGE 11, PRE-IRRADIATION DATA SHEET CHANGE TO INPUT BIAS CURRENT MATCH (CHANNEL TO CHANNEL) LIMITS FROM 120 nA to 200 nA. PAGE 13, PRE-IRRADIATION DATA SHEET CHANGE TO INPUT BIAS CURRENT MATCH (CHANNEL TO CHANNEL) LIMITS FROM 100 nA to 180 nA. 02/10/09 • PAGE 13, TABLE II, ELECTRICAL CHARACTERISTICS, (PRE-IRRADIATION) VS= 3V, 5V, DELETED 3V. PARAMETER AVOL, DELETED VS = 3V, VO = 75mV TO 2.8V, R1 = 10k. + PARAMETER CMRR, COMMON MODE REJECTION RATIO - DELETED VS = 3V, VCM = V TO V ; DELETED VS = 3V, VCM = 0.5V TO 2.5V. + PARAMETER CMRR, MATCH (CHANNEL-TO-CHANNEL) - DELETED VS = 3V, VCM = V TO V ; DELETED VS = 3V, VCM = 0.5V TO 2.5V. PARAMETER ISC, DELETED VS = 3V. • PAGE 14, TABLE IIA, ELECTRICAL CHARACTERISTICS, (PRE-IRRADIATION) VS= 3V, 5V, DELETED 3V. 02/25/10 • E CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART REVISION INDEX REVISION INDEX PAGE NO. REVISION PAGE NO. REVISION APPLICATION 1 E ORIG DSGN ENGR MFG CM QA PROG FUNCT 2 E 3 E 4 E 5 E 6 E 7 E 8 E 9 E 10 E 11 E 12 E 13 E 14 E 15 E LINEAR TECHNOLOGY CORPORATION MILPITAS, CALIFORNIA TITLE: MICROCIRCUIT, LINEAR, RH1499M 10MHz, 6V / µs, QUAD RAIL-TO-RAIL INPUT AND OUTPUT PRECISION C-LOAD OP AMP SIZE SIGNOFFS DATE CAGE CODE 64155 CONTRACT: DRAWING NUMBER 05-08-5199 REV E FOR OFFICIAL USE ONLY LINEAR TECHNOLOGY CORPORATION Page 1 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E 1.0 SCOPE: 1.1 This specification defines the performance and test requirements for a microcircuit processed to a space level manufacturing flow. 2.0 APPLICABLE DOCUMENTS: 2.1 Government Specifications and Standards: the following documents listed in the Department of Defense Index of Specifications and Standards, of the issue in effect on the date of solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS: 2.2 3.0 MIL-PRF-38535 Integrated Circuits (Microcircuits) Manufacturing, General Specification for MIL-STD-883 Test Method and Procedures for Microcircuits MIL-STD-1835 Microcircuits Case Outlines Order of Precedence: In the event of a conflict between the documents referenced herein and the contents of this specification, the order of precedence shall be this specification, MIL-PRF-38535 and other referenced specifications. REQUIREMENTS: 3.1 General Description: This specification details the requirements for the RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp processed to space level manufacturing flow. 3.2 Part Number: 3.3 Part Marking Includes: 3.4 RH1499MW (Glass Sealed Ceramic Flatpak, 14 LEAD) a. LTC Logo b. LTC Part Number (See Paragraph 3.2) c. Date Code d. Serial Number e. ESD Identifier per MIL-PRF-38535, Appendix A The Absolute Maximum Ratings: Note 1/ Note 1/: Absolute Maximum Rating are those values beyond which the life of a device may be impaired. LINEAR TECHNOLOGY CORPORATION Page 2 of 15 SPEC NO. 05-08-5199 REV. E 3.5 Electrostatic discharge sensitivity, ESDS, shall be Class 2. 3.6 Electrical Performance Characteristics: The electrical performance characteristics shall be as specified in Table I (Pre-Irradiation), Table IA (Post-Irradiation), Table II (Pre-Irradiation), and Table IIA (PostIrradiation). 3.7 Electrical Test Requirements: Screening requirements shall be in accordance with 4.1 herein, MIL-STD-883, Method 5004, and as specified in Table IV herein. 3.8 Burn-In Requirement: Static Burn-In, Figure 4; Dynamic Burn-In, Figure 5. 3.9 Delta Limit Requirement: Delta limit parameters are specified in Table III herein, are calculated after each burn-in, and the delta rejects are included in the PDA calculation. 3.10 Design, Construction, and Physical Dimensions: Detail design, construction, physical dimensions, and electrical requirements shall be specified herein. 3.11 4.0 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp 3.10.1 Mechanical / Packaging Requirements: Case outlines and dimensions are in accordance with Figure 1. 3.10.2 Terminal Connections: The terminal connections shall be as specified in Figure 2. 3.10.3 Lead Material and Finish: The lead material and finish for Device shall be Alloy 42 and the lead finish is hot solder dip (Finish letter A) in accordance with MIL-PRF-38535. Radiation Hardness Assurance (RHA): 3.11.1 The manufacturer shall perform a lot sample test as an internal process monitor for total dose radiation tolerance. The sample test is performed with MIL-STD-883 TM1019 Condition A as a guideline. 3.11.2 For guaranteed radiation performance to MIL-STD-883, Method 1019, total dose irradiation, the manufacturer will provide certified RAD testing and report through an independent test laboratory when required as a customer purchase order line item. 3.11.3 Total dose bias circuit is specified in Figure 3. 3.12 Wafer Lot Acceptance: Wafer lot acceptance shall be in accordance with MIL-PRF-38535, Appendix A, except for the following: Topside glassivation thickness shall be a minimum of 4KÅ. 3.13 Wafer Lot Acceptance Report: SEM is performed per MIL-STD-883, Method 2018 and copies of SEM photographs shall be supplied with the Wafer Lot Acceptance Report as part of a Space Data Pack when specified as a customer purchase order line item. VERIFICATION (QUALITY ASSURANCE PROVISIONS) 4.1 Quality Assurance Provisions: Quality Assurance provisions shall be in accordance with MIL-PRF38535. Linear Technology is a QML certified company and all Rad Hard candidates are assembled on qualified Class S manufacturing lines. LINEAR TECHNOLOGY CORPORATION Page 3 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E 4.2 Sampling and Inspection: Sampling and Inspection shall be in accordance with MIL-STD-883, Method 5005 with QML allowed and TRB approved deviations in conjunction with paragraphs 3.1.1, 3.2.1, and 3.4 of the test method. 4.3 Screening: Screening requirements shall be in accordance with MIL-STD-883, Method 5004 with QML allowed and TRB approved deviations in conjunction with paragraphs 3.1, 3.1.1, and 3.4 of the test method. Electrical testing shall be as specified in Table IV herein. 4.3.1 4.4 Analysis of catastrophic (open/short) failures from burn-in will be conducted only when a lot fails the burn-in or re-burn-in PDA requirements. Quality Conformance Inspection: Quality conformance inspection shall be in accordance with 4.2 and 4.3 herein and as follows: 4.4.1 Group A Inspection: Group A inspection shall be performed in accordance with 4.1 herein, per MIL-STD-883, Method 5005, and specified in Table IV herein. 4.4.2 Group B Inspection: When purchased, a full Group B is performed on an inspection lot. As a minimum, Subgroup B2 (Resistance to Solvents / Mark Permanency) and Subgroup B3 (Solderability) are performed prior to the first shipment from any inspection lot and Attributes provided when a Full Space Data Pack is ordered. Subgroup B5 (Operating Life) is performed on each wafer lot. This subgroup may or may not be from devices built in the same package style as the current inspection lot. Attributes and variables data for this subgroup will be provided upon request at no charge. 4.4.2.1 Group B, Subgroup 2c = 10% Group B, Subgroup 3 = 10% Group B, Subgroup 5 = *5% (*per wafer or inspection lot whichever is the larger quantity) Group B, Subgroup 4 = 5% Group B, subgroup 6 = 15% 4.4.2.2 All footnotes pertaining to Table IIa in MIL-STD-883, Method 5005 apply. The quantity (accept number) of all other subgroups are per MIL-STD-883, Method 5005, Table IIa. 4.4.3 4.5 Group D Inspection: When purchased, a full Group D is performed on an inspection lot. As a minimum, periodic full Group D sampling is performed on each package family for each assembly location every 26 weeks. A generic Group D Summary is provided when a full Space Data Pack is ordered. 4.4.3.1 Group D, Subgroups 3, 4 and 5 = 15% each (Sample Size Series). 4.4.3.2 All footnotes pertaining to Table IV in MIL-STD-883, Method 5005 apply. The quantity (accept number) or sample number and accept number of all other subgroups are per MIL-STD-883, Method 5005, Table IV. Source Inspection: 4.5.1 The manufacturer will coordinate Source Inspection at wafer lot acceptance and pre-seal internal visual. LINEAR TECHNOLOGY CORPORATION Page 4 of 15 SPEC NO. 05-08-5199 REV. E 4.5.2 4.6 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp The procuring activity has the right to perform source inspection at the supplier’s facility prior to shipment for each lot of deliverables when specified as a customer purchase order line item. This may include wafer lot acceptance and final data review. Deliverable Data: Deliverable data that will ship with devices when a Space Data Pack is ordered: 4.6.1 Lot Serial Number Sheets identifying all devices accepted through final inspection by serial number. 4.6.2 100% attributes (completed lot specific traveler; includes Group A Summary) 4.6.3 Burn-In Variables Data and Deltas (if applicable) 4.6.4 Group B2, B3, and B5 Attributes (Variables data, if performed on lot shipping) 4.6.5 Generic Group D data (4.4.3 herein) 4.6.6 SEM photographs (3.13 herein) 4.6.7 Wafer Lot Acceptance Report (3.13 herein) 4.6.8 X-Ray Negatives and Radiographic Report 4.6.9 A copy of outside test laboratory radiation report if ordered 4.6.10 Certificate of Conformance certifying that the devices meet all the requirements of this specification and have successfully completed the mandatory tests and inspections herein. Note: Items 4.6.1 and 4.6.10 will be delivered as a minimum, with each shipment. This is noted on the Purchase Order Review Form as “No Charge Data”. 5.0 Packaging Requirements: Packaging shall be in accordance with Appendix A of MIL-PRF-38535. All devices shall be packaged in conductive material or packaged in anti-static material with an external conductive field shielding barrier. LINEAR TECHNOLOGY CORPORATION Page 5 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E (W) Glass Sealed Flatpak / 14 LEADS CASE OUTLINE θja = +170°C/W θjc = +40°C/W FIGURE 1 LINEAR TECHNOLOGY CORPORATION Page 6 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E TERMINAL CONNECTIONS FIGURE 2 LINEAR TECHNOLOGY CORPORATION Page 7 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E TOTAL DOSE BIAS CIRCUIT FIGURE 3 LINEAR TECHNOLOGY CORPORATION Page 8 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E STATIC BURN-IN CIRCUIT Glass Sealed Flatpak / 14 LEADS FIGURE 4 LINEAR TECHNOLOGY CORPORATION Page 9 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E DYNAMIC BURN-IN CIRCUIT Glass Sealed Flatpak / 14 LEADS FIGURE 5 LINEAR TECHNOLOGY CORPORATION Page 10 of 15 SPEC NO. 05-08-5199 REV. E RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp TABLE I: ELECTRICAL CHARACTERISTICS (PRE-IRRADIATION) NOTES FOR THIS TABLE ARE ON PAGE 14. LINEAR TECHNOLOGY CORPORATION Page 11 of 15 SPEC NO. 05-08-5199 REV. E RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp TABLE IA: ELECTRICAL CHARACTERISTICS (POST-IRRADIATION) NOTES FOR THIS TABLE ARE ON PAGE 14. LINEAR TECHNOLOGY CORPORATION Page 12 of 15 SPEC NO. 05-08-5199 REV. E RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp TABLE II: ELECTRICAL CHARACTERISTICS (PRE-IRRADIATION) NOTES FOR THIS TABLE ARE ON PAGE 14. LINEAR TECHNOLOGY CORPORATION Page 13 of 15 SPEC NO. 05-08-5199 REV. E RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp TABLE IIA: ELECTRICAL CHARACTERISTICS (POST-IRRADIATION) Special Note: Note 1 pertains only to the Absolute Maximum Ratings on page 2 of this specification. LINEAR TECHNOLOGY CORPORATION Page 14 of 15 RH1499M, 10MHz, 6V / µs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp SPEC NO. 05-08-5199 REV. E TABLE III: POST BURN-IN ENDPOINTS AND DELTA LIMIT REQUIREMENTS TA = 25°C, VS = + 15V PARAMETER VOS ENDPOINT LIMIT MIN MAX MIN DELTA MAX UNITS -800 + 800 -250 + 250 μV IB -715 + 715 -350 + 350 nA IOS -70 + 70 -50 + 50 nA TABLE IV: ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUP FINAL ELECTRICAL TEST REQUIREMENTS (METHOD 5004) 1*, 2, 3, 4 ,5, 6 GROUP A TEST REQUIREMENTS (METHOD 5005) 1, 2, 3, 4 ,5 ,6 GROUP B AND D FOR CLASS S ENDPOINT ELECTRICAL PARAMETERS (METHOD 5005) 1, 2, 3 *PDA APPLIES TO SUBGROUP 1. PDA TEST NOTE: The PDA is specified as 5% based on failures from Group A, Subgroup 1, tests after cooldown as the final electrical test in accordance with method 5004 of MIL-STD-883. The verified failures of Group A, Subgroup 1 and delta rejects after burn-in divided by the total number of devices submitted for burn-in in that lot shall be used to determine the percent for the lot. LINEAR TECHNOLOGY CORPORATION Page 15 of 15